Search Documents

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976

By R. L. Montgomery

The heats of formation of lanthanum sulfate and the enneahydrate are -939.8 ± 3.1 and -1,587.1 ± 3.2 kcal. per mole, respectively. The heat of hydration is -32.5 ± 3.5 kca1. per mole. These values were obtained from heat-of-solution measurements of lanthanum oxide and salts. Low rates of solution precluded more accurate determinations of the thermal data. The heat of formation of the chloride was similarly observed to be -256.18 ± 0.28 kcal per mole. Heats of solution and combustion of lanthanum metal yield mutually concordant results, and earlier discrepancies reported in the literature may be ascribed to impurities.

Jan 1, 1959

By L. Mark Irwin, R. A. Marsyla

The objective of this laboratory investigation was to develop a mattesmelting process for the recovery of copper from industrial smelter dusts . Experimentation was conducted on three samples of Cottrell precipitator dust from a northern Michigan smelter with variations in the following conditions : Temperature , charge composition , pelletization , and moisture content . Based on chemical analyses of the furnace slags , poorest recovery of copper was effected in smelting dry charges regardless of composition . Some improvement was noted with uniformly moistened charges and still more with pelletized (but dry) mixes , but best results were obtained from smelting moist , self - fluxing pellets . Under favorable conditions , experiments yielded furnace slags with an average copper content of only 0.15 percent , which is well below that of industrial copper reverberatory slags .

Jan 1, 1963

By D. R. Tesarik

The factor of safety, the traditional measure of stability for earth embankments, is graphically presented in factor of safety charts in this Bureau of Mines report. Factor of safety contours are drawn for homogeneous earth embankments for two contrasting situations: (1) no phreatic surface and (2) a phreatic surface that assumes 10-pct freeboard. The factor of safety can be read directly from the charts if the physical properties of the soil and the geometry of the embankment are known. The curves provide a quick first approximation of the "most stable" and "least stable" condition of the embankment. The Simplified Bishop Method was used for the safety factor calculations, and a sequence of least squares curve fitting steps was used to present the factor of safety in final chart form.

Jan 1, 1981

By T. A. Henrie, J. D. Marchant, E. S. Shedd

Cerium metal was electrowon in a fluoride bath from cerous oxide and tapped from the cell during prolonged operation . Electrolyte constituents were CeF , BaF₂ , and LiF. Twenty- seven pounds of metal of 99.8 percent purity were produced at a rate of 3 pounds per hour and tapped from the cell . Principal impurities were molybdenum , aluminum , oxygen , and carbon . The operating parameters , such as electrode geometry , bath compositions , and oxide feed rate , were investigated . Anode reactions were found to be important factors in cell operation . Stable cerous oxide reacted more uniformly at the anode surface than ceric oxide . Electrowinning was conducted in crucible hearths consisting of both frozen electrolyte and molybdenum metal . Both materials proved satisfactory and did not react with the molten cerium . Stable cerous oxide was prepared by carbothermic reduction and used as a feed material . Cell design proved to be an important factor in continuous cell operation . Complementary to the investigations of electrowinning of cerium , the metal was purified by electrorefining in a chloride electrolyte .

Jan 1, 1964

By A. C. Rice

This report describes a chemical process for preparing solutions of trivalent rare-earth chlorides from sulfate solutions obtained by treating bastnasite concentrate. The chief impurity in the final solution is cerium, and this element is less than 1 percent of the rare-earth oxides. The solution is used directly in the separation of rare-earth elements by ion-exchange methods. The attractive features of the process are that the chemicals are inexpensive and the steps few. The process starts with precipitating the rare-earth hydroxides from sulfate solutions with caustic soda. After the hydroxides are dried to oxidize the cerium, they are treated with dilute hydrochloric acid to dissolve away the trivalent rare-earth elements, leaving the tetravalent cerium. Details for controlling the leaching step are described. The process shortens older procedures by omitting the usual oxalate or double-sulfate-precipitation step.

Jan 1, 1959

By K. A. Johnson, H. F. Yancey

"INTRODUCTION Coals vary so widely in their burning characteristics that all coals prepared for domestic stoker use cannot be burned efficiently on every type of stoker. The overfeed stoker, a large number of which are in use in the Pacific Northwest, operates satisfactorily when burning low- to high-ash, noncaking bituminous or subbituminous coals, whereas on the clinkering-type, underfeed, bituminous stoker both caking and noncaking bituminous and subbituminous coals are burned, generally with ash contents below 12 percent and ash-softening temperatures between 1,800º and about 2,600º F. Because fly ash continues to be one of the most troublesome factors in domestic underfeed stokers, noncaking coals especially must be chosen carefully with respect to size composition, particularly as regards the exclusion of excessive fines. Their formation as a result of degradation in storage handling or because of crushing in .the stoker worm will increase the fly-ash nuisence.Bituminous and subbituminous coals with higher ash-softening temperatures and, often, higher ash contents have not been able to enter the domestic stoker-coal market in the Pacific northwest because clinkers are not formed readily during clinker-type underfeed-stoker burning, especially in mild weather, and because of the labor and attendant inconvenience required in handling larger volumes of ash. The work described in this report was undertaken to enable mines producing coals of the kind described to enter the stoker-coal markets. The anthracite stoker selected was one that conveys the refuse from the ash pit of the furnace and deposits it into one of two covered, dust-tight disposal cans."

Dec 1, 1945

By M. M. Kirk

Forced-air cooling of cold-mold arc furnaces for melting zirconium and similar metals has been investigated and found to be practical from the stand-point of heat transfer. It is believed that this technique offers a significant reduction in explosion hazard from that inherent in water cooling, the current industrial practice. A copper crucible, with longitudinal, integral-type fins and with an outer jacket to confine the airstream, appears to be the best general design for air-cooled operation. Cutting the fins into short segments and bending the segments to produce a herringbone effect increased the airstream's turbulence and was found, on test, to increase the heat transfer up to 35 percent.

Jan 1, 1959

By Robert H. Merrill

This report summerizes the various studies made to determine the size and support of roofs in the upper shale formation, White Pine Copper Mine, Michigan. These studies were a cooperative effort of the White Pine Copper Company and the Federal Bureau of Mines. Before this investigation, the upper shale formation had been found to contain about 30 to 40 percent of the total mineralization in the ore zones. Investigators estimated that this shale could be economically mined by room-and-pillar methods, provided that the roof would stand over spans of 25 to 32 feet. The problem remained to determine the number of bolts required to safely support these spans. Unbonded fractures in the roof structure of the deposit complicated the use of laboratory methods for determining bolted roof support. Therefore, a method was devised to determine the in-place support which would consider the unbonded fractures. In this method the roofs of 3 rooms with spans of 20, 28, and 36 feet were intentionally overbolted as the rooms were mined. Following stability tests that sometimes exceeded 6 months, the bolts were selectively removed and roof sag, roof strain, and changes in bolt loads were measured concurrently. The number of bolts required for support of these spans was computed from these data.

Jan 1, 1961

By H. S. Caldwell

A magnesium-base incendiary alloy, containing about 20 percent cadmium, 4 percent aluminum, and 0.5 percent zinc, was investigated in a series of vacuum-distillation experiments to determine the feasibility of recovering magnesium and cadmium as refined metals. Alloys prepared in the laboratory and actual bomb-casing alloy were studied at temperatures of 550° to 750° C. and pressures of 100 to 150 microns. Simple distillation and fractional distillation methods were only partly effective in separating the cadmium and magnesium. They were separated satisfactorily, however, with a special vapor baffle designed to condense the metals selectively. Magnesium and cadmium products were 99 percent pure and together comprised 82 percent of the total condensate. About 17 percent of the condensate was intermediate-grade alloy that could be recycled with new charge and contained about 70 percent magnesium and 30 percent cadmium.

Jan 1, 1959

By A. C. Johnson

This paper is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods and costs at various mines in the United States. It describes such methods at the Lincoln tungsten mine of the Wah Chang Mining Corp., Lincoln County, Nev. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods, practices and costs. The Lincoln mine in Lincoln County, Nev., in the southeastern part of the [tate], was acquired by the Wah Chang Mining Corp., in April 1951. Mining methods and costs are of special interest at this property because of the low costs and good production record achieved through a well planned program of exploration, development, and exploitation. Operations were discontinued in July 1957 after the Federal Government suspended the tungsten purchase program.

Jan 1, 1959

By P. M. Daling

The objectives of this study were to examine a representative cross section of formal safety analysis techniques developed for the nuclear and aerospace industries, to recommend those methods that would be suitable for application to the mining industry, and to include those methods in a user's manual. Volume II of this report, the user's manual, describes several methods that were determined to be immediately transferrable to the mining industry. The handbook gives detailed instructions on appropriate application and utilization of the methods. Other techniques will require further development before they can be effectively transferred to the mining industry.

Jan 1, 2006

By Jim F. Lemons

The Bureau of Mines Minerals Availability System collected and analyzed data for 34 nonlaterite and 9 nickeliferous laterite domestic chromite deposits in order to assess their viability as sources of chromium under present technologic and economic conditions. These 43 deposits, none currently in production, contain approximately 6.3 and 22.3 million metric tons of Cr203 at the demonstrated and identified resource levels, respectively. Approximately 4.6 and 15.6 million metric tons of Cr203 are recoverable at the demonstrated and identified levels, respectively, for the 34 nonlaterite deposits. None of these resources are economically recoverable at January 1981 market prices. Production of metallurgical-grade chromite (market price $128 to $144) would require a minimum chromite market price of $237 per metric ton. Chemical-grade chromite production (market price $74 to $85) would require a chromite market price in excess of $188 per metric ton. From the 34 nonlaterite deposits, roughly 5.4 and 17.6 million metric tons of ferrochrome could be produced at the demonstrated and identified resource levels, respectively; however, a minimum market price of $770 per metric ton of ferrochrome would be required to stimulate production. The nine nickeliferous laterite deposits were not evaluated through production stages because of uncertainties in process technology and cost.

Jan 1, 1982

By Martin Hertzberg

The early and reliable detection of the self-heating of combustible substances in mines is of considerable importance to the mining community. This Bureau of Mines report describes the results of a variety of studies of incipient combustion and its detection. Heated samples of coal, wood, and various polymers were used to evaluate the relative sensitivities of several types of detectors. The laboratory results indicate that submicrometer particulate detection is the most universal and sensitive method. Carbon monoxide detection was as sensitive as submicrometer particulate detection for pyrolyzing coal but was relatively insensitive to pyrolyzing wood or plastics. The conventional type of ionization smoke detector was the least sensitive for coal and of intermediate sensitivity for wood and plastics. Self-heating experiments with Pittsburgh seam coal piles of varying particle sizes gave ignition temperatures of 170° C for 4-to 7-µm dust, which increased monotonically with particle size. The measured heating rates were compared with data from an adiabatic calorimeter to obtain preexponential rate constants. The preexponential rate constants varied linearly with the surface area per unit mass of sample as would be expected for heterogeneous surface oxidation. The propagation behavior of ignition waves and the overall self-heating appears to depend critically on the magnitude of the convective flows induced, which counteract the depletion of oxygen in the void spaces of the pile. Classical theories of thermal ignition require substantial modification to be applied reliably to such cases.

Jan 1, 1977

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

By A. W. Fahrenwald

[In studying coarse sand flotation3/ the question of the relation between fineness of grinding and mill capacity logically arose. Everyone familiar with present fine-grinding practice knows that the capacity of a ball mill or similar mill is determined, among other things, by the fineness of the finished product. Undoubtedly a great many mining companies must have a good deal of data directly bearing on this point, yet no quantitative relationship between ball-will capacity and fineness of finished product has been established. The experimental study presented here is an effort to establish this relationship in a semiquantitative way. The subject is a tremendously large one and grows in complexity as the study becomes more searching. In this work the power consumed by the mill in the various experiments was not determined end neither vas the steel consumption measured; mill capacity only was considered.]

Jan 1, 1930

By F. D. DeVaney

The supply of manganese is a subject of much interest. The idea of obtaining it from rhodochrosite-MnC03 is attractive because the carbonate is supposed not to be so contaminated with impurities as the commonly utilized oxides. Large bodies of rhodochrosite-bearing rock have been known for a long while to exist at Butte, Mont. Hence samples were obtained from that place. In the two samples examined quartz was the chief diluting substance. The leaner sample was about one half quartz; some copper, lead, zinc, and iron sulphides were also present. The rhodochrosite amounted to about 40 per cent, so that the sample had a tenor of about 20 per cent manganese. This sample was the subject of the examination reported herein.

Jan 1, 1928

By R. G. Knickerbocker, A. L. Fox, J. Koster, P. R. Perry

"During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report. 6/ The geology of the Marysvale region has been reviewed recently. 7/The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.The preliminary work just mentioned had given indications of the separation of sulphate salts high in potassium from fusions of alunite with borax glass.During the course of further work along those lines, fusions of boric acid and alunite were tried. No separation of salts was obtained, but it was observed that rather complete removal of so3 from the alunite occurred and that the sinter could be leached with water to give a solution contain¬ing most of the potash and a residue containing most of the alumina. The reaction that takes place can probably be written 8/:"

Mar 1, 1939

1. Alford, N.G. quantity, of timber used in soft-coal mines and how much will be needed for the future. Gives a table of estimated increase in mine timber consumption in the future. A.I.M.E. Separate. 1336-C 1924. 2 Clark, B.M. The forest and the mine. Rept. Conference of Wood-Using Industries, Harrisburg, Pennsylvania. Apr. 13-14, 1921, pp. 58-62. Describes experience of a Pennsylvania mining company in depletion of timber supply and conservation methods adopted.

Jan 1, 1925

By Charles E. Whieldon

The importance of recovering more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. A previously published report4/ described the highly successful results of waterflooding in the Weir sand in eastern Kentucky. A more recent report5/ evaluated the results of waterflooding in Roane County, W. Va. (See fig. 1.) Two waterflooding projects have been operated in Pleasants County, W. Va. (fig. 2), one by the Dearborn Oil & Gas Corp. in the Cow Run sand near Calcutta, McKim and Washington districts, and the other by George C. Schoonmaker in the Maxton sand at Bens Run, Union district. This report report describes the waterflood operation near Calcutta, W. Va.

Jan 1, 1960