Search Documents

By J. A. Sutton

In connection with, a stream-pollution-research project, a colorimetric method was developed for concentrations of 1 to 30 p.p.m, of pine oil in water. The method depends on the stable bluish-green color produced when pine oil is reacted with vanillin-hydrochloric acid reagent at 60° C. for 25 minutes. The colorimetric reaction actually determines alphaterpineol, the principal component in pine oil. Some waters may require a special preparation in which ion-exchange resins are used to remove interference. ACKNOWLEDGEMENTS The author wishes to express his appreciation to A. A. Berk, chief of the Industrial Water Branch, Bureau of Mines, for helpful advice and encouragement during the progress of this work and to B. P. Martinez, chief of the Stream Pollution Research Section, for assistance with the manuscript. Thanks are also due to W. D. Bishop of the Hercules Powder Co., Wilmington, Del., for supplying the principal components of pine oil.

Jan 1, 1953

The Bureau of Mines conducted a field study to assess the performance of various chain pillar configurations in terms of gate road entry sta-bility. Vibrating wire stressmeters (VWS's) were installed in four consecutive gate road chain pillars. Field data collected during panel retreat were analyzed to gain a better understanding of the mechanics of vertical load redistribution in gate road chain pillars as it relates to ground control problems. Several different pillar configurations were investigated including abutment-yield and yield-abutment-yield designs. VWS data indicate that average pillar loads were lower and appeared abutment-yield pillar arrangement was utilized. port the occurrence of severe roof and pillar to stabilize when an Data analyses also supdeterioration that was visually observed in the tailgate entries during panel extraction.

Jan 1, 1988

By C. B. Daellenbach

A prototype particulate size analyzer system was developed that would rapidly determine size distributions of homogeneous and two-mineral materials in the 74-micrometer (200-mesh) to 7-micrometer size range. The system sizes particles in a series of hydrocyclone elutriation steps and senses the weight of the five sized fractions by nuclear attenuation techniques. Size distribution of materials was determined from experimentally developed mathematical relationships that existed between particulate weight and the measured transmittance of gamma rays from an Americium-241 source. In the developmental phases, size distributions of three minerals (quartz, magnetite, and hematite) and a laboratory prepared two-mineral mixture of quartz and magnetite were accurately determined by the prototype system. In later stages of the investigation, semiconcentrates, an intermediate magnetic product from a taconite plant, were evaluated. Using 25-gram feed samples of this industrial material, the analyzer system was found to predict weight percentages for individual size fractions with an accuracy of ±0.85 percent or better at a 95-percent confidence level.

Jan 1, 1974

By A. Wahab Khair

"Geologic materials emit transient noises when stressed /1/. The rate and pattern of these transient noises or acoustic emissions (A.E. hereafter) depend on the stages of deformation of the material /2/. It has been demonstrated that rock/coal fracture processes under stress consist of three distinctive stages--crack initiation, propagation and ultimate fracture--and that coalescence of numerous cracks leads to ultimate failure rather than the propagation of a single crack /2,3/. This paper presents an analysis of fracture formation in rock/coal specimens subjected to straight wedge indentors using A.E. technique.The effect of specimen geometry, wedge indentor angle, confining pressure, and material anisotropy on fracture type (tension, extension, and shear crack), fracture length, and fracture intensity were studied. Two types of material mainly Berea sandstone and Coal Berg No. 2 coal were used in this study. Prior to the experiment the mechanical properties of both sandstone and coal were determined using rectangular specimen (Figures 1 a) in standard compression tests and are given in Table 1. In this study cylindrical and rectangular specimens were first prepared to proper dimensions of 2 in. x 1.5 in. and 3 in. x 1.5 in. x 1.5 in. (5.08 cm x 3.81 cm and 7.62 cm x 3.81 cm x 3.81 cm), respectively and then instrumented with SR-4 strain gages as shown in Figure 1. The instrumented specimens were then tested under four distinct load boundary conditions as illustrated in Figure 2. During a typical experiment the instrumented specimen was placed in a specially designed loading jig (Figure 3) where a predetermined lateral pressure was applied mechanically to the specimen by adjusting the inner plate of the confining chamber via screw while monitoring strains in the specimen. Using rock/coal elastic constants and measured strains, a predeter¬mined lateral pressure was applied to the specimen. Then a vertical load was applied by the straight edge of a wedge indentor attached to the upper platen of the universal loading machine via ball and socket arrangement (Figure 4). The arrangement allowed uniform application of load in a straight line manner on the surface of the specimen. During the test a number of parameters namely strains, load and A.E. rates were recorded (Figures 5a-b)."

Jun 1, 1988

By John I. Kasteler

The Rambler mine is in the Douglas mining district, Albany County, Wyo. (fig. 1). The property was first operated about 1870 for gold found in the outcrop of a leached ore body. Copper and metals of the platinum group were discovered, in 1900, or soon thereafter, and intermittent mining was done until 1918, when a fire destroyed the surface plant, and the underground workings caved. The mine has since been idle. The Bureau of Mines conducted a development project on the property from October 1942 to October 1943, with a recess period between November 1942 and August 1943. Ten diamond drill holes, totaling 1,859 linear feet, were drilled on the property (fig. 2). The mine dump was sampled after preparation with a bulldozer. Assay determination and spectrographic analyses disclosed small quantities of copper and metals of the platinum group in the samples. Determinations were made on 11 samples from the diamond drill holes and 23 samples from the mine dump. The assay results and spectrographic analyses are given in tables 1 and 2. The logs of the diamond drill holes are given in an appendix to this report.

Jan 1, 1949

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

This report describes serious injuries occurring to bulldozer operators working at U.S. coal, metal, and nonmetal mines. The period covered is 1988-97. The data were collected by the Mine Safety and Health Administration (MSHA). A total of 873 injury records are examined. These injuries resulted in 18 fatalities and 31,866 lost workdays. All of these injuries occurred to dozer operators while they were doing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Injury records are categorized by activity (task being done), incident result (what apparently happened to the dozer), and operator impact (how the operator was injured). Where information is available, contributing factors are identified. This classification system supplemented the standard injury/illness data classification system compiled by MSHA. The results of the study indicate that, from 1993 to 1997, the number of serious injuries to dozer operators declined by 30%. The reduction in serious injuries was accompanied by a decrease in days lost due to injury. Although the number of reported injuries has decreased, dozer operators being jolted and jarred accounts for the largest percentage (70% of the incidents) and severity (75% of the workdays lost) of serious injuries while operating the equipment. Vertical jars (while backing up the dozer) resulting in injury to the operator accounted for a sizable percentage of jolting and jarring injuries. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over, or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fall over or rollover, 7 out of 26 were killed. Overall, 80% of the fatalities occurred while working near an edge or hidden void or on a steep slope. Further reductions in injury risk will require more widespread use of seatbelts, field and laboratory research interventions to better assess the effect of alternative engineering (e.g., seat and seat suspension) designs to dampen or isolate the effects of shock and vibration, and continued focus on hazard awareness, recognition, and response.

Jan 4, 2001

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By G. E. McElroy

This paper3/ is one of a limited series being prepared by the Bureau of Mines to supplement a more extensive series on mining and preparation methods in the various mining districts of the United States. It describes ventilation methods and practices at the anthracite collieries in the Northern field of the anthracite measures of Pennsylvania as obtained by personal inspections in twenty of the larger collieries during 1933 and 1934 and from supplementary information furnished then and later by operating officials. This field is one of the four major divisions - Northern, Eastern Middle, Western Middle, and Southern - into which the anthracite deposits of Pennsylvania are naturally divided, and constitutes, in plan, a slightly bowed lens, about 60 miles long, and that extends from Forest City on the north through Scranton, Pittston, Wilkes-Barre, and Nanticoke to Shickshinny on the south with a. maximum width of 6 miles. It is the oldest and largest producing field of the four, and has produced continuously from 1S09. The total anthracite production for the State reached a peak of about 100,000,000 tons a year in 1917, but in recent years production has averaged about 50,000,000 tons, of which somewhat over half comes from this Northern field. The operations of three of the largest producing organizations in the State are almost wholly included in this field, as well as about half of the operations of two others of the six largest producers, It comprises the first 14 of the 25 numerically designated anthracite State inspection districts.

Jan 1, 1937

By S. S. Todd

[The purpose of this investigation was to obtain, heat-of-formation values a four Common titanates and, to conjunction with other requisite data, to derive free-energy-of-formation values In tem peratures in the range of 1,600°-1,800° K. T ht four titanites are tricalcium ?ditanite !['a¬spheremr?raritanar( rint-tir.rniurn rill( 1 This rc rr,rt sul,rlc?nu?nIs :r },r; vinu~ hul,lrc.irse,n3i n wlti h eht-rmnnIN-ti i n c {ar.a ai?rc? pu -,csseeri (or, 11 in(c-rnxiLIic co mrc+unrls conraininL~ rir:,niurrl. 'f Lac? !1~:)mc? c?xpcrirnc'ntnl n-ut rhod w,i. rna~loycul. lic?.ats of for rn:ltion of rlre comi?c,unr4~ it 29S.N. ut re mca,urc?,l by tioItl[ion e':iIorrr)utrv, using a ctrneaR }ryrlrc,fllanric-hY rir~chlorie- ,aci l mixttrrt .is rhr c-zle~rinrrrric- fluid and rc.actic~n rtu,liura}.]

Jan 1, 1956

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935

By L. C. IlsLey

The work of the electrical section of the Bureau of Mines may be considered to have had its beginning in April , 1909 , when H. H. Clark was , appointed electrical engineer in the U. S. Geological Survey. The first manuscript prepared by members of this section was Miners Circular 5, which was issued in October , 1911. During each succeeding year additional papers have been published dealing with questions relating to electrical safety. Since 1916 the electrical section has also conducted laboratory investigations on flame safety lamps and gas- detecting devices and has published reports relating thereto . The following selected list of publications covering safety studies and activities of the electrical section has been prepared for the convenience of those who wish to keep themselves advised concerning electrical safety matters . The list includes only such publications as are applicable to present-day prac tices .

Jul 1, 1930

By G. S. Price

This paper, which describes the milling practice at the Page concentrator of the Federal Mining and Smelting Co., is one of a series being prepared by the Bureau of Mines. The Page mine and mill are located on Silver Creek, 3 miles west of Kellogg, Idaho, and 1 mile south of United States Highway No. 10. Supplies and concentrates are hauled by truck over an automobile road which connects Highway No. 10 with the property. The concentrator has capacity to treat 300 tons of ore per day and utilizes all-flotation methods of treatment. Power is supplied from the main line of the Washington Water Power Co. which runs from Spokane, Wash., to Kellogg, Idaho. Water is obtained from the mine and also from a well which is situated 1 mile distant from the concentrator and about 600 feet in elevation below the concentrator.

Jan 1, 1932

By Leland A. Yerkes

Refining aluminum from crude aluminum alloys by the subhalide reaction was investigated to develop a method of producing aluminum by means other than electrolysis of its oxide. The best materials and design for the apparatus and also optimum operating conditions, including temperature, pressure, vapor flow rate, and composition of alloy charge were studied. In the subhalide process, aluminum-trihalide vapor reacts with aluminum in the alloy under high temperature and low pressure, forming volatile aluminum monohalide which reverts to aluminum metal and aluminum trihalide on cooling. The only halide used in this investigation was aluminum trichloride. The crude aluminum-silicon alloys used as the principal raw material contained from 21.9 to 36 percent aluminum, and significant quantities of iron and titanium. These alloys were produced by direct electric smelting of clays. Graphite tubing that was heated by an induction coil proved to be satisfactory material for the laboratory reactor chamber, Enclosed in an insulated glass or quartz pipe, the reactor was used in both vertical and horizontal positions with various baffle and tray arrangements for directing the trihalide vapor both over and through the alloy. Aluminum trichloride vapor was generated in the sublimer at one end of the glass pipe, passed into the reactor where contact was made with the crude alloy, and aluminum monochloride gas was formed. When the gaseous mixture of aluminum monochloride and unreacted tri-chloride passed out of the reactor and entered the condenser, the gases were cooled to 900° C. or less, causing the monochloride to disproportionate into aluminum and aluminum trichloride vapor. The aluminum was deposited on the condenser walls while the aluminum trichloride vapor was carried out of the condenser and into the opposite end of the glass pipe where it solidified on the cooled copper coils.

Jan 1, 1961

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steel in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steel as impurities. For example, silicon additions form SiO2 or combinations of SiO2 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MnO, SiO2, and Al2O3, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods. The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By N. S. Dalal, B. Jafari, F. H. Y. Green, M. M. Suryan, V. Vallyathan

"Freshly ground and aged anthracite and bituminous coal samples were investigated by electron spin resonance (ESR) spectroscopy to detect the presence, concentration and reactivity of free radicals. Freshly ground anthracite coal produced greater concentration of free radicals than the bituminous coal, and the radical reactivity was also greater for the anthracite. The reactivity of the newly produced free radicals in the anthracite dust correlated with the dust's toxicity. Furthermore similar coal-based free radicals were detected in the lung tissue of autopsied coal miners, suggestive of persistent reactivity by the embedded coal dust leading to the progressive disease process. Results of the studies on the severity of coal workers' pneumoconiosis (CWP) and free radical concentration m lung tissue support this hypothesis.INTRODUCTIONCOAL WORKERS' PNEUMOCONIOSIS (CWP) has been an important topic of concern to miners, mining engineers, epidemiologists and medical researchers for decades. It is well known that the prevalence and severity of CWP differ markedly between different regions and mines despite comparable exposures to respirable dust (REISNER and RoBOCK, 1977; HURLEY et al., 1979). These variations in pathogenicity of coal mine dusts can only partially be explained by differences in the mineral composition and by rank of coal (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). Cytotoxity studies on mammalian cells do not correspond well with the human disease pattern (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al.,1980; VALL YA THAN et al., 1988). For example, while epidemiological studies of coal miners (REISNER and ROBECK, 1977; HURLEY et al., 1979) indicate that the prevalence of CWP correlates roughly with the rank of coal, such correlation has not yet been established in biological studies, despite considerable effort (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). In order to help resolve this apparent paradox we have undertaken a systematic study to evaluate whether any correlation exists between the concentration of free radicals present in fresh or aged coal dusts from two well-characterized U.S. coals. This study was also prompted in part by observations reported in the literature that organic free radicals can be formed on the surface of freshly fractured coals (LEBEDEV et al., 1978; DULIBA and CLARKSON, 1984). In particular, ARTEMOV and REZNIK (1980) noted that the decay lifetimes and, hence, the reactivity of the organic free radicals formed on crushing Russian coals, .depended"

Jan 1, 1989

By H. Stuart Auvil

Twelve samples of run-of-oven coke were taken at coke plants in the United States and Canada. Sampling procedure was directed toward obtaining the highest possible degree of uniformity in the gross samples, so that variations in results caused by sampling variations were at a practical minimum. Under these conditions the standard deviation of the screen analysis test on 500-pound samples is found to range from 1.2 percent for the 1-inch screen to 4.5 percent for the 5-inch screen. At present, the A.S.T.H. standard method of test requires that results be reported to the nearest 0.1 percent. This implies a higher than actual degree of precision, and revision of the report required by the method is suggested. Much larger Samples than are generally tested are required to reduce normal testing errors to a point where they are not appreciable fractions of the total variations found in a smoothly operating plant. For example, it is deduced that over 100,000 pounds of coke must be screened to determine if ordinary day-to-day variations in screen analysis have appreciable effects on the performance of a blast furnace.

Jan 1, 1950

By L. R. Burdick, J. F. Barkley

"There is a general conceit in the coal trade that the moisture- and ash-free B.t.u. of coal from the same seam, and surely from the same mine,is substantially a constant; that calculation of the moisture- and ash-free B.t.u. value from the proximate analysis and B.t.u. determined in the laboratory will reveal whether a coal came from a given area or seam; and that, having this constant, the B.t.u. value of a coal sample can be calculated fairly closely upon a dry or as-received basis from the moisture and ash values of its proximate analysis.To illustrate with a simple example;"

Jun 1, 1941

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By Oliver Bowles

From the most remote periods of civilization, stone Las been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns) or single markers to great obelisks and pyramid or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1050 at a cost estimated at a: high as $50,000,000, and it is today an object of unusual attraction for travelers. Other magnificent memorials, both ancient and modern, are to be found in many lands. Memorials of varying design have characterized the passing centuries and have found an important place in the New World. In early days, monuments were chiefly imported into America, but gradually an extensive memorial stone-manufacturing industry developed on this side of the Atlantic. Sales value of domestic memorials, f.o.b. quarry or mill, attained a maximum of $17,488,755 in 1920, and retail sales, of course, reached a much higher figure. Modest markers and tombstones are to be found in almost every rural community in the United States, and there are many elaborate and costly monuments in and near urban centers.

Jan 1, 1938