Search Documents

By N. A. C. Smith, D. D. Stark

"Sulphur is apparently a normal Constituent of crude petroleum, but in most crudes is present in percentages of less than one-half of one per cent. Some crudes, however, contain more, and occurrences have been reported of heavy asphaltic oils with as much as five per cent of sulphur.Occurrences of Sulpher-bearing CrudesIn North America, the fields rest of the Mississippi River are almost entirely free from sulphur oils, the time oil from Northern Ohio and Indiana, and the Potrolia crude in Ontario, being practically the only ones which contain sulohur in amounts over 0.5. per cent. In the Mid-Continent district the production of high sulphur crude in general is small and unim¬portant. The two main excentions are the Healdton field in Oklahoma and the El Dorado field in Arkansas, both of which produce oils with considerable sulphur content. In the Wyoming field, one sand, the Ember Sandstone, pro¬duces a crude of high sulphur content, and it is probable that this crude rill be of considerable importance as production increases. At present, however, very little crude is produced from this formation. In the Gulf Coast conditions are irregular, some crudes being low in sulphur and others comparatively high. The same is largely true of California. The crudes of Mexico contain notable amounts of sulphur, and as they have been of great commercial importance in this country, a typical sample of light Mexican crude was selected for the present study. It is probable that the results obtained poly also (but to a lesser degree) to other sulphur-bearing oils. An analysis of this crude will be found in Table 3, also analyses of other typical sulphur-bearing crudes from different sections of the United States."

Mar 1, 1924

By Seth C. Schaefer

The Federal Bureau of Mines studied the Gibbs free energies of formation of chromous fluoride (CrF2), chromic fluoride (CrF3), and chromium (II,III) fluorides (CrF2.40 and CrF2.45) with high-temperature galvanic cells employing calcium fluoride doped with 1 mole-pct yttrium fluoride as the electrolyte. Free-energy changes were obtained from open-circuit potential measurements for the following cells: Cr, CrF2 // CaF2 // NiF2, Ni (a) NiO, NiF2 // CaF2 // CrF3 , Cr203 (b) CrF2 , CrF2.40 // CaF2 // NiF2, Ni (c) and CrF2 ?45 , CrF3 // CaF2 // NiF2, Ni (d) with the following overall reactions Cr(s) + NiF2 (s) = Ni(s) + CrF2 (s) (1) 3NiO(s) + 2CrF3 (s) = 3NiF2 (s) + Cr203 (s) (2) 5CrF2 (s) + NiF2 (s) = 5CrF2.4O (s) + Ni(s) (3) and 3.64CrF2.45 + NiF2 (s) = 3.64CrF3 (s) + Ni (s) . (4) These results were combined with the best available literature values of ?Gf° of NiF2, NiO, and Cr203 to deduce Gibbs free energies of formation for the chromium fluorides expressed as follows: ?Gf°(CrF2) = -179.31 + 24.33 X 10-3T ± 0.43 kcal-mole. (5) (858.1 - 964.9 K) ?Gf° (CrF3) _ -226.16 + 1.82 X 10-3T ± 0.79 kcal/mole (6) (880.8 - 957.8 K) ?Gf°(CrF2.40) _ -213.65 + 32.14 X 10-3T ± 0.44 kcal/mole (7) (0053.9 - 936.8 K) and ?Gf°(CrF2.45) _ -176.17 - 12.67 X 10-3T ± 0.80 kcal/mole (8) (875.1 - 937.6 K). Free energies and equilibrium fluorine pressures for three univariant and one bivariant equilibria are illustrated.

Jan 1, 1976

By Jr. Hill

Laboratory metallurgical treatments of three high-iron bauxite ores from Arkansas were conducted to determine the relative effectiveness of experimental methods for recovering alumina and a commercially acceptable iron concentrate. The standard for evaluating recoveries from experimental processes was the Al2O3 recovery from Bayer digests of the crude ores; recoveries from digestion of the three ores were 74.1, 87.4, and 88.7 percent. Flotation, magnetic separation, or various combinations of digestion, calcination, and reduction-sintering, leaching, and magnetic separation of leach residues failed to produce Al2O3 recoveries as high as the standard. A high-iron-bearing fraction, containing between 68 and 78 percent of the total iron, was produced in a three-phase treatment involving a caustic, lime reduction-sinter of the crude ore, water extraction of Al2O3 from the sinter, and magnetic separation of the leach residue.

Jan 1, 1967

By Wesley T. Holmes

In this final stage of a three-part investigation of the smelting of titania-bearing iron materials, the Bureau of Mines conducted semicontinuous smelting tests in a laboratory electric arc furnace on four concentrates and one are. The objective was to substantiate the significance of liquidus temperature measurements in predicting satisfactory slag compositions in electric furnace smelting of titaniferous magnetites to produce pig iron. Previously obtained liquidus temperature data were used in determining flux requirements. Self-fluxing pellets of either ore or concentrate plus fluxes and reductants were made to produce pig iron and slags containing 0.2 to 0.6 percent titanium. Individual constituents of the slags generally agreed within 5 percent with the value of the corresponding constituent of target composition. Liquidus temperature of furnace slags generally agreed within 50° C of the value obtained from corresponding nominal synthetic slag. The results of the three phases of the investigation may serve as guide-lines for determining flux requirements in smelting a wide variety of titaniferous magnetites and other titania and iron-bearing materials.

Jan 1, 1969

By T. F. Mitchell, Walter J. Long

"SUMMARYThis report is one of a series giving results of laboratory and pilot-plant investigations of the concentration of western manganese ores begun in December 1940. Data given summarize results of laboratory investigation of three samples of complex oxide manganese ores from the Madeline property, Lake View, and Victory claims, Clallam County (Olympic Peninsula), Wash. The samples represented an extremely intimate and complex association of manga¬nese oxide minerals with silica and iron.Owing to the complex nature of the ores, no effective concentration by ore-dressing methods was possible. No high-grade manganese concentrates were produced and the highest recovery at minimum accountable grade was only 55 percent on one of the ores tested.Since the Clallem County ores did not respond to ore-dressing methods, leaching processes were investigated, results of which are to be published in a separate report.INTRODUCTIONOre-beneficiation tests were conducted on three samples of manganese oxide ere from the Madeline, Lakeview, and Victory claims, Clallam County, Wash. The ores are extremely complex because of the unusually small size of manganese mineral particles, their mode of occurrence, and relationship to the gangue. None of the three ores was amenable to the production of high-grade manganese products by ore-dressing methods."

Dec 1, 1945

By Allan M. Johnson

Case histories were used to document and evaluate deficiencies in underground mine closures which have resulted in post-operation problems such as subsidence shaft failures, acid or toxic water drainage and others. Three different underground mining districts in the United States were investigated; 1) an iron mining district in Michigan 2) coal mining districts in eastern Ohio and southern Illinois and 3) three metal mining districts in central Colorado. Previous work in the Michigan district on problems with subsidence and acid water drainage provided the background from which the concept for this project was developed Student investigators working towards their MS degrees in Mining Engineering did the work on the eastern coal and western metal districts. The combined studies show that problems from acid water drainage, subsidence and inadequately protected mine shafts are the most severe and widespread. Suggestions of a technical nature are presented as partial solutions to some of these problems. It was determined that pre-closure evaluations could result in the identification of some potential problems that may occur after the mine is closed. Early recognition of these problems would be an advantage for at this time more options are available to the mine operator to either prevent them or to plan for their occurrence. Mine closure and reclamation should be considered as a part of mining and be incorporated in the mining plan. This would result in reduced environmental impact and would be achieved at a lower overall cost to the mining companies and to society. The role of water in the occurrence of several types of subsidence during mine flooding was significant at some mines in the Michigan district. These mechanisms which involve, friction reduction, gravity loading, overburden transport and hydraulic forces in a flooded mine probably have a broader effect than is currently recognized. Control of these processes may offer some interesting options during mine closure. It is recognized that technical solutions alone cannot provide all of the answers to problems associated with underground mines. Education, modified attitudes on the part of regulators and operators, and a more realistic perception of the importance and value of mining by the general public are also needed.

Jan 1, 1983

By Charles E. Green

This study was conducted to identify, evaluate, and develop procedures to minimize or eliminate safety hazards associated with the electrokinetic dewatering process, such as toxic and volatile gas emissions, electrical shock, accidental detonation of explosives, electrochemical corrosion of metal appurtenances, and possibly others. The identification, evaluation, and procedure development were based on pertinent literature, existing safety regulations, interviews with mine personnel, physical and mechanical properties of the electrokinetic dewatering process, and physical characteristics of the material to be dewatered. The electrokinetic dewatering process was described in detail. Potential safety hazards were identified and evaluated. Procedures and/or safety regulations were developed to minimize or eliminate the potential hazards. It was recommended that the electrokinetic dewatering process when used in deep metal mines be properly monitored to obtain additional information on other potential hazards that possibly exist.

Jan 1, 1979

By Clarence O. Babcock

This Bureau of Mines publication presents guidelines for mining near surface and underground bodies of water. The guidelines were based on information developed under contract in three phases of study, as follows: (1) Collection and documentation of data from worldwide sources; (2) application of existing guidelines, foreign, Federal, and State, to case histories of previous inundations; and (3) development of recommended guidelines for underground coal mining near bodies of water aimed at maximum efficient utilization of underground coal resources consistent with minimizing inundation hazards. While the contract guidelines were for the mining of coal seams, they may also be used for mining any tabular sedimentary mineral deposit. Tables are given for the determination of the size of coal pillars needed; for other bedded deposits, similar tables could be determined based on their strength properties.

Jan 1, 1977

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

By Thomas M. Barczak

The transverse loading requirement for stoppings as specified in the current Code of Federal Regulations is 39 psf. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where the dominant parameter is the tensile strength of the sealant. A new protocol based on arching has been developed to determine the true transverse load capacity of stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid-arching of stoppings was developed and verified through full-scale in-mine tests. Using this protocol, a systematic study of the design parameters that affect arching capability in block stoppings was conducted. The study included a theoretical assessment of arching and development of design formulations that can accurately define the transverse load capacity of various stopping constructions under various loading conditions. This approach should lead to a safer mine environment by matching the transverse load capabilities of the stopping design to the requirements in the mine to ensure proper ventilation control is maintained.

Jan 1, 2005

By C. J. Wilhelm

The Bureau of Mines, under its cooperative agreement with the Kansas State Board of Health, has been conducting a study of the various methods of oil-field brine disposal in the oil fields of Kansas. A previous report5/dealt with this problem in the Ritz-Canton field, McPherson County, Kans. A preliminary survey of the Arkansas River drainage area in western Kansas was made during November and December 1934 and January 1935, and a second survey was made approximately one year later during the months of December 1935 and January and March 1936. In addition to the data on the production of oil and 'brine in the various fields and the methods used for handling the brine, the surface drainage and character of the surface soil in the various oil-producing areas were studied.

Jan 1, 1936

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By B. P. Martinez

A process for regenerating spent pickle liquor is proposed in which some of the water is evaporated at atmospheric pressure and ferrous sulfate is precipitated as monohydrate crystals..Equilibrium conditions are set for a slurry of crystals in a mother liquor containing 5 percent FeS04 and 45 percent E2S04, by weight, and boiling at about 235° F. The slurry is pumped continuously to a filter, and the mother liquor from the filter is pumped back for reuse in the pickling tanks. The net result of the process is to remove ferrous sulfate in the regeneration plant at the same rate ac it is produced in the pickling tanks. This process is integrated with the steel-pickling operation and controlled by the pickling requirements for particular steels. Spent pickle liquor is removed for regeneration continuously from both batch and continuous picklers at higher acid concentrations than would be dumped to waste because no acid is neutralized or discarded. However, the process is not designed to keep a sulfuric acid concentration stronger than 25 percent in any pickling tank. To retain flexibility in the pickling operation, all acid makeup is added to the pickling tanks. Rinse waters are used as water makeup for the pickling tanks. To further minimize waste of acid in the rinse waters, improvements of rinsing practices are outlined.

Jan 1, 1953

By A. L. Engel

This report is a compilation of results of brief preliminary tests on sulfide ores that contained gold and silver and, in some cases base metals. It is a companion paper to a recent similar report on oxide ores. Simple treatment methods employing the least possible equipment sometimes produce satisfactory results on marginal ores and in small-scale operations. Investigations of typical ores from newly discovered or recently explored mining districts have been made in continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno station, Bureau of Mines. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores as well as the conservation and recovery .of values in products that were discarded from former operations because of inability to treat them profitably. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas same involved samples of old dumps or tailings piles. The test work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials. The samples were representative of the districts from which they wore obtained, so this information should be helpful in the future development of these districts.

Jan 1, 1951

By J. S. Kennedy, R. G. Omeara

Beryllium is a strategic metal of ever-increasing peacetime importance because of the unusual properties of beryllium-copper alloys. These unusual characteristics are the combination of high strength and hardness, high fatigue resistance, and high wear resistance in alloys that have the corrosion resistance of copper. The principal industrial source of beryllium is the mineral beryl, a beryllium-aluminum silicate that occurs in pegmatites associated with quartz, feldspar, mica, and smaller amounts of various accessory minerals. The beryl is usually recovered in processing the pegmatites for the recovery of some of the other mineral constituents. Pegmatite deposits are found in various parts of the United States, but those in the Black Hills of South Dakota are the source of most of domestic production. The beryl marketed from the South Dakota pegmatite deposits occurs as coarse crystals, which are obtained by hand sorting. These pegmatites also contain other valuable minerals.

Jan 1, 1948

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part I of the report contains the results of the field teats.5 The studies were made on an oil lease in a so-called "sour district," near Borger, Tag., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it Was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field teat proved that aluminum lease tanks will withstand corrosion by hydrogen sulphide, but it was found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By W. H. Carrington, A. C. Richardson

"INTRODUCTION The Powhatan mine of the Franklin Coal Mining Co. is located in the western part of Jefferson County, Ala., on the Louisville and Nashville Railroad, 40 miles west of Birmingham. The Mary Lee bed at this point yields coal with fair coking qualities, but with an ash content as mined so high as to prohibit its use in the production of metallurgical coke. At present the entire output of the mine is washed in single-compartment jigs and marketed as locomotive and domestic fuel.Figure 1 gives a typical seam section of the Mary Lee bed at the Powhatan mine. This section shows that the bed is divided by rock partings into three benches. In many parts of the mine, particularly in the older workings the roof rock is so weak that it can not be held without excessive timbering. This condition has restricted the operation in many parts of the mins to the middle and bottom benches of coal. The 6 inches of draw rock between the top and middle benches is very strong and makes an excellent roof requiring only a normal amount of timbering to support it. In the newer workings of the mine the character of the rock above the top bench is strong and it is believed that in the future it will be possible to work all three benches. This study was undertaken for the purpose of determining the washing characteristics of the Mary Lee bed at Powhatan and the effect on these characteris-tics of including or omitting the coal from the top bench. It was also the purpose of the study to show whether it would be possible to produce a washed product sufficiently low in ash to be used for the manufacture of metallurgical coke. This paper is one of a series of reports on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and tin University of Alabama. With the cooperation of the coal producers of Alabama. It contains the results of screen sizing and float-and-sink tests of representative samples of run-of-mine coal, and the results of table tests on the minus 3/16-inch sizes of the raw coal."

Apr 1, 1933

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978