Search Documents

By E. Morrice, R. D. Smith

Thermal expansion and electrical resistance measurements were made on cerium metal from 4° to 300° K. The apparatus developed , including a specimen holder and a cryostat system , are described along with the experimental techniques used in obtaining the measurements . The total linear thermal expansion Data at of 99.83 weight - percent cerium metal between 4 ° K and room temperature was 4.24 percent . The resistivity at 4° K was 7.0 x 10-6 ohm- centimeter . 4° K indicate a fundamental relationship between residual resistivity and purity of cerium metal . The effects of annealing and repeated thermal cycling on resistivity were determined .

Jan 1, 1964

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By N. E. Hanna

To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain safety tests prescribed by the Federal Bureau of Mines. These tests are described in Schedule 1-G4/ (explosives) and Schedule 26A5/ (blasting devices). An explosive or blasting device that passes the appropriate tests is placed on the active permissible list. As this list is subject to continuous revision, it has been the practice of the Bureau of Mines to publish periodically the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. The present circular gives all explosives and blasting devices on the active permissible list as of December 31, 1957, and shows all changes, additions, and transfers in that list between December 31, 1951,6/ and December 31, 1957.

Jan 1, 1958

By O. M. Schaus

The following is a description of the methods employed at the Eureka-Asteroid mine, which is situated on the Gogebic range, at Ramsey, Mich. The mime is operated by the Castile Mining Co. under the direction of Oglebay Norton & Co. This paper has been prepared in accordance with an outline furbished by the United States Bureau of Mines, and in one of a series, on mining methods and costs covering the principal minim operations throughout the United States. ACKNOWLEDGMENTS The author acknowledges the assistance of the mining organization of the Castile Mining Co. in the preparation of this paper.

Jan 1, 1930

By R. D. Groves

Techniques were developed for preparing metallurgical-grade copper powder from industrially produced cement copper. Flotation was used for rejecting discrete gangue particles, acid leaching to remove residual iron and aluminum, hydrogen reduction to eliminate oxygen, sintering to consolidate the fine-sized copper, and grinding to obtain copper powder. Powders prepared from six different cement copper samples contained, in percent, 98.5 to 99.0 Cu, 0.10 to 0.05 Fe, 0.10 to 0.08 insoluble material and the remaining individual impurities less than 0.15 percent. The apparent density, flow characteristics, and other physical properties were suitable for powder metallurgy applications. An economic evaluation showed that this process was economically feasible. Processing costs appeared modest when considering that copper powder commands a price normally about 17.5 cents per pound over that of electrolytic copper.

Jan 1, 1971

By Jr. Reed

The only known large deposits of talc in Alabama occur near Winterboro, Talladega County. Preliminary examinations were made, and work by the Bureau of Mines was recommended. The deposits were investigated to determine the amount and grade of talc present and to search for new talc deposits in the general area. Seventy-five holes, totaling 3370.4 feet, were drilled with Government-owned core drills from August 1, 1948, to February 11, 1949, and 27 samples were taken for assay. This report presents the factual data disclosed by drilling and the results of beneficiation of the talc.

Jan 1, 1950

By Iain Finnie

This report is in three parts. The first part presents a review of theoretical models which have been developed to study removal operations for various types of materials. In the second part, a brief summary is given of coal cutting research. The majority of this work has been carried out in Britain using chisel type bits rather than the conical picks which are in general use in this country. However, a comparison of specific energies measured for conical picks in the laboratory and in the mine shows very encouraging correspondence. In the third part of the report, analytical models for coal cutting by picks are suggested. An extension of the British "tensile breakage" theory, developed for chisels, is given for picks. The role of crushing and cutting in coal removal is discussed as a theory which combines the two processes is shown to give reasonable predictions for specific energy requirements. Finally, directions in which the existing theory could be improved are presented and the need for further research is emphasized.

Jan 1, 1977

By J. W. Thompson

A contract stipUlating for the delivery of quantities of phosphate rock" f. o. b. mines," and stipUlating that" while this contract is in form an absolute sale for a fixed quantity in each year, it is mutually understood and agreed that the purchase is for the buyer's consumption and not for a sale; the buyer agreeing to give to seller the refusal of any surplus over and above the actual consumption. Buyer is at liberty to increase or diminish the quantity called for in any year, to the extent of not exceeding 10 per cent; provided that the quantity to be taken shall not be less than buyer's consumption; provided further that notice of such increased or diminished demand be given seller 12 months in advance of such change," is to be construed as a contract for the sale of stated quantities of rock, deliverable in approximately equal quantities during each year for the specified series of years, subject only to be increased or diminished after specified notice in any year, where the amount taken would not be les<; than the buyer's consumption, not exceeding 10 per cent, and the contract indicating that the rock was intended by both parties for consumption in the fertilizer plant of the buyer. but the quantity to be taken was not limited by the necessities of' the plant.

Jan 1, 1916

By L. M. Burman

The phase-boundary pressure required to maintain a natural hydrocarbon fluid in a single phase must be considered in planning the recovery of reservoir liquids by miscible-phase processes. The change in the phase-boundary pressure at reservoir temperature that results when a light component or a mixture of light components is added to a reservoir fluid is an especially important consideration. The cricondenbar pressure (maximum phase-boundary pressure) and the critical pressure are unique correlated pressures that have been utilized to calculate the change in phase-boundary pressure that may result when the composition of a reservoir liquid is altered by an additive. In this study one reservoir oil and three gas-condensate fluids are used as examples. Correlations pertaining to the critical and cricondenbar states in chapters 4 and 5 of Bureau of Mines Monograph 10 (3)5 were used to demonstrate how butane and lighter components added to these reservoir fluids affect their phase-boundary pressures.

Jan 1, 1962

By B. K. Shibler, I. S. Solet, H. W. St. Clair

"This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics.The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor. Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.INTRODUCTIONAlthough the United States is the world's largest consumer of tin, virtually no tin ores occur within our national borders. Most of the world's tin supply comes from alluvial deposits in the Far East and in Africa, The major sources of tin ores are Malaya, Indochina, Bolivia, Belgian Congo, Nigeria, Thailand, Burma, China, and the United Kingdom. Bolivia is the only important source of tin in the western hemisphere. It was the chief source of tin f or the United States during World War II. The Government-owned tin smelter at Texas City, Tex., was built primarily for smelting Bolivian ores and depends largely on Bolivian ores for its operation. Bolivia is the only major tin-producing country in which the tin ores occur as vein or lode deposits requiring underground mining. Most of the tin from the Far East and Africa is mined by dredges from alluvial or placer depos its. It is recovered as a high-grade concentrate of cassiterite relatively free from impurities. The tin minerals in the lode deposits are more intimately associated with other minerals and more difficult to separate into a clean concentrate. Furthermore, a large part of the tin in the original ore is lost during concentration. The ores as mined contain only a few percent of tin, so they must be milled to separate the gangue minerals and produce a concentrate containing 30 to 40 percent tin before they are shipped to the smelter. The losses of tin that occur during milling vary from 18 to 65 percent. The average recovery of tin from Bolivian ores is probably 50 to 60 percent."

Dec 1, 1954

By Gary W. Krantz

Fibered, portland-cement-based gunite products were applied in the Bureau of Mines Lake Lynn Laboratory Experimental Mine using a variety of pneumatic guns and gunning crews, The demonstrated wet-mix (with silica fume), dry-mix, and surface bonding products were sampled by the Bureau and subjected to a suite of engineering analyses. Gunite flexural and compressive strength, rebound, permeability, porosity, dust loading, shooting rate, crew requirements, and cost factors were evaluated. Steel, fiberglass, or polypropylene fibers were contained in all but two of the gunires tested. Both Bureau and private testing laboratory analyses are provided for some products. Electron probe micro-analysis and X-ray diffraction analysis were performed on the silica fume fraction of the wet-mix gunite to characterize the dust. Aggregate size fraction distribution analyses were performed to provide strength relationships. Results indicate that all of the commercially available fibered-gunite materials tested can provide beneficial sealant, spall prevention, or roof stability control attributes for underground mining environments when applied by an experienced crew using a well-maintained gun, in accordance with product manufacturers&apos; recommendations and when used for the designated purpose.

Jan 1, 1984

By R. G. Warncke, Stanley M. Walker

The United States Bureau of Mines was created by an act of Congress in 1910 as a governmental agency to work , on a national scale , toward reducing the huge annual loss of life in the production and processing of the Nation's minerals . From 1906 to 1910 , inclusive , nearly 2,500 miners lost their lives in 84 major explosion disasters , and more than 13,000 suffered fatal injuries from all causes in the coal mines of the United States . Also , conditions in the metal and nonmetal mines were proportionately hazardous during this period , and the total loss of life in all mines and quarries exceeded 3,000 annually and approximately 250,000 workers suffered serious injuries . Under these conditions it is readily understandable why Congress took notice of this " high cost of mining" , and from the investigations and hearings of the day emerged the Bureau of Mines charged with the prevention of accidents and the preservation of the health of all those engaged in the mineral industry; this has continued to be a most important part of the work of the Bureau . Throughout its existence the Bureau of Mines has had no legal authority of enforcement , except during war years , when enforcement necessary to the national security was given to it . The Bureau believes that persuasion , with factual evidence , is the proper and best way to obtain compliance with the safety suggestions made by its engineers and scientists . There is no panacea for accidents , nor will any single " approach " , instill safety consciousness in all workers , and without it accidents will occur --and occur again . To persuade men to work safely, numerous forms of appeal are required to reach the various temperaments of workers in many types of mines operating under diverse conditions .

Nov 1, 1949

By L. R. Burdick, J. F. Barkley

"The agglomerating index of coal is an index based upon the nature of the coke residue left when the standard volatile-matter determination of the well-known proximate analysis is made. In this determination a small amount of coal is heated in a container to about 950° C. (1,742° F.), at which temperature the volatile matter is driven off, leaving a coke formation. The coke residues for various coals are quite different in physical structure: and, for some time past, work has been done on studies of the nature of these residues in connection with the coking of coal. In 1934 Gilmore, Connell, and Nicolls proposed use of the agglomerating index for indicating the dividing line between noncaking coals and those having weakly caking properties. 4/ Its use was adopted in the standard classification of coals by rank as a requisite physical property index to differentiate semianthracite from low-volatile bituminous coal and also high-volatile ""C"" bituminous from subbituminous ""A"" coal, as shown in table 1, the standard coal classification adopted by the American Society for Testing Materials and the American Standards Association. 5./In studying the agglomerating properties of coals based on the coke residue the Bureau of Mines has adopted the notation given in table 2. Coals that in the volatile-matter determination give a coke residue either in the form of an agglomerate button that will support a 500-gram weight without pulverizing or a button that shows swelling or cell structure are considered to be agglomerating."

Nov 1, 1938

In spite of advances in measurement techniques and an explosive increase in the volume of research, our understanding of human strength remains in its introductory stages. It is clear that muscle strength is a highly complex and variable function that depends on a large number of factors. It is not surprising, therefore, that large differences in strength exist not only between individuals, but even within the same individual tested repeatedly on a given piece of equipment. The issue is compounded by the fact that correlations of strength among different muscle groups in the same individual are generally low, and tests of isometric strength do not necessarily reflect the strength an individual might exhibit in a dynamic test. As a result of these and other influences, great care needs to be exercised in designing, evaluating, reporting, and interpreting muscular strength assessments. Traditionally, tests of muscular strength were in the domain of the orthopaedist, physical therapist, and exercise physiologist. Such tests are also an important tool for the ergonomist, however, because of the high strength demands on workers in manual materials-handling tasks. In some cases, task demands may approach or even exceed the strength that an individual is voluntarily willing to exert in a test of strength. In such cases, evidence suggests that the likelihood of injury is significantly greater than when the task demands lie well within an individual&apos;s strength capacity. Because the relationship among strength capabilities, job demands, and musculoskeletal injury has been established, it is apparent that tests of muscular strength may benefit the ergonomist both in designing jobs and in ensuring that individuals have sufficient strength to safely perform physically demanding jobs. Several strength assessment techniques have been employed for these purposes, each possessing unique characteristics and applicability to job design and worker selection procedures. Our main purpose has been to elucidate these strengths and weaknesses, so that tests of strength may be properly applied in designing jobs and selecting workers. One of the crucial points we have emphasized is that any test of strength used in job design or worker selection must be directly related to the demands of the job.(1) For example, if an occupational lifting task has a high dynamic component, a test of isometric strength is not likely to provide the data necessary for proper design of the job. Of course, dynamic strength tests would also be misapplied in assessing a job requiring isometric exertions. Another potential pitfall is using tests of strength on isolated muscle groups and assuming that they are indicative of whole-body strength. For example, one might mistakenly assume that dynamic trunk extension strength represents a person&apos;s capability to perform a lifting task. However, an individual&apos;s lifting capacity may be entirely unrelated to trunk extension strength. It may, instead, be limited by an individual&apos;s arm or leg strength, depending on the task being performed. A final point on strength assessment should be made. An individual&apos;s strength capability cannot be considered a fixed human attribute. Strength training regimens can increase an individual&apos;s strength capability by 30%-40%. Whether

Jan 1, 1998

By D. Harrington

During the 5-year period 1906-10 inclusive, 84 major disasters (a major disaster being one in which 5 or more lives are lost) occurred in the coal mines of the United States, or an average of 17 per year, and the total number of fatalities from coal-mine gas and dust explosions (major plus minor) for the 5 years aggregated 2,338 or 477.6 per year. The monotonous continuance of coal-mine disasters month by month aroused the people of the United States to such an extent that it was felt necessary for the Federal Government to try to do something looking to the avoidance of the admittedly excessive loss of life in our coal mines, and this was one of the deciding factors in the establishment of the United States Bureau of Mires in 1910. That results have been obtained in this particular cause of coal-mine accidents may be seen from the fact that for the year 1933 but one major explosion disaster occurred in the coal mines of then united States and the total number killed in that disaster was 7. Unquestionably the coal-mining industry through use of oaf or mining practices and aided by the various kinds of work of the Bureau of Mines looking to the prevention of mine fires and explosions is in large part responsible for this very creditable change. If the gas and dust explosion fatality rate of 1.059 per million tons of coal produced during the period 1906-10 inclusive had continued to the first of January 1934, instead of the 6,373 deaths which actually occurred due to gas and dust explosions, there would have been 13,480. Hence, during the 23 years existence of the Bureau of Mines there has apparently been a saving of about 7,102 probable deaths, or an average of more than 300 per year, from gas and dust explosions as against the number which would have occurred had the 1.059 gas and dust explosion fatality rate for the period 1906-10 continued. Thirty-nine persons were killed in all kinds of explosions (both major and minor) in the coal mines of the United States in 1933; if the 1.059 gas and dust fatality rate of the 1900-10 period had been in effect in 1933, about 400 persons world have been killed. Unquestionably, the various teachings of the U.S. Bureau of Mines looking to the avoidance of explosions and fires in mines have had a vital influence in reducing the number of explosions and fires and also in decreasing their destruction in case they occur.

Jan 1, 1934

By Allen D. Look

In the prevention of accidents in milling operations, the proper installation and guarding of electrical and mechanical equipment, safe clearances, good housekeeping, adequate fire protection, adequate ventilation, dust and fume control, and good illumination, as well as safe practices, are essential. In the new concentrator of the Magna Copper Co., Superior, Ariz., many safeguards were incorporated and safe practices instituted to minimize accident hazards. The purpose of this paper is to describe some of these features and practices.

Jan 1, 1951

By Sidney Katell

The reaction of coal, oil, or natural gas with air and oxygen and/or steam yields a gas containing varying amounts of impurities. Depending on the raw material and the end use of the product, these impurities include solids, such as dust or slag, and gases, such as hydrogen sulfide, carbon dioxide, and nitrogen. Considerable effort has been expended in developing and operating purification systems, and the literature is replete with equipment data and operating results. The research problems, the design, and the operation of the various systems have been the subjects of patent applications, journal articles, and textbooks.

Jan 1, 1959

In this U.S. Bureau of Mines report, in situ vat leach mineral recovery system concepts are described and cost compared with conventional mining and pad and autoclave leach processing systems. In the proposed systems, leachable ores are enclosed in place in reagent-impermeable in situ vat constructions. The ores are then rubbled and flood leached or flood oxidized and leached. The in situ vats are called stope leach or stope autoclave vessels. The report also proposes ore body-adjacent in situ vat constructions containing rechargeable processing stopes. A series of ore body-specific, innovative, and conventional mineral recovery systems case study designs are described and prefeasibility level costed. Based on a comparison of these prefeasibility level cost estimates, the proposed systems are determined to be economically competitive with conventional min¬eral recovery systems. The in situ vat leach mineral recovery systems concepts for leachable and refractory ores are developed around the drill-split narrow-vein and longwall mining methods described in part 1 of this Information Circular series.

Jan 1, 1995

The Ringelmann Smoke Chart fulfills an important need in smoke abatement work and in certain problems in the combustion of fuels. A knowledge of its history and method of preparation is, therefore, of interest to many. Since instructions on its use are not shown on the recent edition of the chart, those included in this revision of the previous Bureau of Mines publication now are a necessary complement to the chart, More detail regarding the use of the chart is included than was given in the earlier version.

Jan 1, 1967

By Peter G. Chamberlain

The surge in gold and silver prices during the 1970&apos;s attracted many new mining operators and has rekindled interest among experienced ones. With its low capital investment requirements and fast payout, leaching has attracted many operators--particularly those with small or low- grade deposits. Although in certain situations leaching offers many advantages over conventional mining methods, many operators are uncertain how these relatively new techniques should be implemented. Consequently the Bureau of Mines has prepared this circular to disseminate information on gold and silver leaching practices, techniques, and problem. Engineering data gathered from 26 operations indicate that most ores are leached in heaps following crushing and distribution on pads. Metal values are recovered from cyanide leach solutions using either zinc precipitation or charcoal adsorption. Potential problems that my hamper on block development of a leaching operation are poor percolation characteristics of the ore, calcium salt buildup, low temperatures, and solution losses. An extensive bibliography on gold and silver leaching is appended.

Jan 1, 1984