Search Documents

By S. Benedict Levin

The Big mine has been a source of mica and high-grade felspar from separate zones in the same pegmatite dike since 1914. In 1943 it became the outstanding producer of strategic mica in New England. The urgent need for sheet mica led to core-drilling by the Bureau of Mines from February to May 1914. Nine diamond-drill hob's aggregating 1,474 feet in length were drilled by the Bureau of Mines with the objective of developing extensions of the known mica shoots. The use of large-diameter bits made it feasible to obtain reasonably reliable results in diamond-drilling this type of deposit.

Jan 1, 1949

The papers contained herein summarize results of various recent Bureau of Mines investigations in the area of mine power distribution systems. They are based on information from Bureau personnel, contractors and grantees, and Mining Enforcement and Safety Administration. Conclusions drawn from a series of parameter measurements on mine power systems, taken over a 3-year span, are presented. Personnel and equipment hazards due to faults on isolated, solidly grounded, and resistance grounded three-phase systems are discussed. Two papers cover dc applications of circuit breakers, including a novel protection scheme for trolley lines. The methods of suppressing induced arcing currents and voltages in a-c machines are evaluated. An evaluation program for ground monitors is described. Acceptance test procedures and the importance of various paparameters for trailing cable splice are covered. A number of techniques for locating faults in trailing cables are described.

Jan 1, 1975

By E. J. Matson

Under the investigation for critical and strategic minerals the Kaiser mine, formerly the Baxter fluorspar property, in northeastern Mineral County, Nev., was explored. The work comprised excavating 32 trenches averaging 90 feet in length, 8 feet in width, and 1 1/2 feet in depth. The trenches were excavated across the strike of the ore body to enable the engineer to spot the diamond-drill holes; 7 such holes were drilled, aggregating 3,276 linear feet. A total of 20 core samples and 107 sludge samples was taken. The work under this program indicated that the fluorspar southwest of the deposit extended laterally and also at depth at least 250 feet below the 400-foot level. INTRODUCTION The Kaiser fluorspar deposit is in the northeastern portion of Mineral County, Nev. Mining was begun about 1928, and the property has been a consistent producer of both Acid- and Metallurgical-grade fluorspar. The mineralized zone has been developed along a strike length of about 2,000 feet and to a depth of over 700 feet along the dip.

Jan 1, 1957

By Douglas C. Corner

This is the first of a series of papers dealing with modern tunnel-driving methods, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines and to be published in a series of information circulars by the bureau. This series will supplement a similar and earlier series of papers dealing with mining methods and costs. ACKNOWLEDGMENTS The author desires to express hiss appreciation, of the assistance of A. C. Dennis, manager for the West Construction Co. Contractors, and Franc: E. Winsor, chief engineer for the Boston Metropolitan District mater Supply Commission who furnished much of the data and detailed description of operation appearing in the following pages. C. F, Jackson, mining engineer, United States Bureau of Mines, collaborated in the preparation and arrangement of the text.

Jan 1, 1931

By Ivor Hawkes

This report describes how longitudinal and bending stress waves in' percussive drill rods generate noise. It is shown that in practical drills the largest noise source is the bending waves, which are mainly generated because of imperfections in the piston, chuck, and drill rod alignment. Equations are presented which enable the noise spectra generated by the bending and longitudinal waves to be precisely predicted. Means for reducing the amplitude of the bending waves are discussed.

Jan 1, 1977

By R. J. Gunderman

Cable reel systems for shuttle cars were investigated to determine whether an improved system could be identified. Interviews and mine visits were conducted to better define limitations and problems with present systems. Although simple and relatively inexpensive, present cable reel systems are not fully satisfactory. Several concepts for a different technical configuration were formulated and evaluated. An all ectric system using electronic control and external sensors was recommended for further development.

Jan 1, 1980

By B. K. Shibler

A highly flexible laboratory-scale fluidized-bed reactor was designed, constructed, and successfully operated continuously at temperatures up to 1,300° C during an investigation of thermal methods for decomposing gypsum. This report discusses briefly the many problems encountered in developing the 10-inch-diameter reactor and describes its design and construction in sufficient detail to enable other research organizations to build a comparable unit. The reactor consists of a 10-inch-inside-diameter vertical tube which can be varied from 6 to 10 feet high; it is formed from 2-and 3-foot sections of silicon carbide pipe. The tube is surrounded by a 3-inch heating space formed by an outer 4.5-inch-thick circular wall of insulating firebrick. A cone-shaped fluidizing chamber is bolted to the bottom of the reactor. Fluidizing gas enters through the bottom of the cone, and ore is introduced by means of a screw feeder connected to an inlet located just above the gas port. A silicon carbide overflow tube of 1.25-inch inside diameter extends upward into the reactor. The depth of the bed is controlled by substituting different lengths of overflow tube. Twin dust-recovery systems, each composed of a cyclone and Fiberglas filter, are attached to two gas outlets at the top of the reactor tube. The reactor is designed for research on both exothermic and highly endothermic reactions. It can be fired externally by means of four natural gas burners that jet tangentially into the annular space at the base of the reactor. Alternatively, it can be fired internally, using a mixture of air or oxygen and natural gas as the fluidizing medium. A separate instrument panel contains flowmeters, manometers, an automatic program controller, and a multiple-point recorder for printing a record of the temperatures measured by thermocouples located at critical points in the reactor.

Jan 1, 1963

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By Burton J. Thamer

Radon emanation coefficients of 0.02 to 0.55 were measured at moisture contents ranging from dry to saturation in eighteen different ores. The emanation coefficients rose from a minimum when dry to a plateau usually starting at 5-20 percent of saturation. A model, using measured pore-size distributions, suggested that the radium mineralization may be confined to annular layers about 0.02 micrometers thick around pores. Radon's diffusion coefficient was determined as a function of moisture. The techniques involved comparing a disc's exhalation as a function of time whether or not the disc had a distributed source. The model was free of approximations and included the effects of porosity and adsorption. An increase of diffusion coefficient with moisture for one or two ores was explained in terms of a model's equation for the diffusion coefficient in terms of both volume and surface diffusion. Radon's adsorption coefficient was determined on a uranium ore.

Jan 1, 1981

By R. C. Annear

This report describes open, sublevel, and shrinkage stoping at the Greenwood mine, operated by Inland Steel-Co. The iron ore mine is in Marquette County, Mich., about 6 miles southwest of Ishpeming (fig. 1). The Greenwood is one of three active underground hard-ore mines on the Marquette range, the others being the Cliffs-Shaft and the Champion mines. The operation reflects an achievement in exploiting small, difficult-to-mine hard-ore bodies lying beneath a 200-foot overburden of glacial drift, which is partly water bearing. This report can indicate only briefly the efforts of personnel in overcoming adverse conditions in mining more than 2 million tons of ore, 80 percent of which was in lump form, for open-hearth production of steel. Significant data presented include descriptions of the principal mining methods employed, sublevel and shrinkage stoping; percent aged mining costs for the entire year 1957, covering both direct mining costs and general expenses; and performance records in units of labor, power, and supplies.

Jan 1, 1960

By A. R. Rule

A flotation process was developed by the Bureau of Mines for separation of carbonate and phosphate minerals occurring in unaltered phosphate ores of the Phosphoria formation. The process involves depression of phosphate minerals with fluosilicic acid and flotation of carbonate minerals with fatty acid emulsions. In individual laboratory tests, selective removal of carbonates was achieved with phosphate recoveries ranging from 60 to 80 pct P205. In continuous-circuit testing, sizing and separate treatment of coarse and fine fractions was necessary to achieve 65-pct P205 recovery. Concentrate grade ranged from 26 to 33 pct P205. The flotation tailings containing primarily carbonate and phosphate minerals is a potential fertilizer material. When reacted with H3P04, concentrated superphosphate containing approximately 40 pct available P205 was obtained.

Jan 1, 1974

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978

By Franklin H. Persse

Domestic bismuth supply was projected from production figures for the ores in which it occurs--copper, lead, zinc, and tungsten. Published and unpublished data concerning host ores were examined to determine bismuth reserves and resources, and mine production. Potential recoverable bismuth occurring with reserves and resources of copper, lead, and zinc was estimated to be 36.3 million pounds. A bismuth availability diagram was developed from quantity estimates and ratios of production cost to value for these host ores. Additional recoverable bismuth occurring with domestic tungsten reserves was estimated to be 1.5 million pounds. Domestic byproduct production of bismuth will approximate 1.3 million pounds annually by 1980. This quantity will provide about 37 percent of the 3.5-million-pound estimated requirement for that year. Known world supply of bismuth appears to be sufficient for world demand to the end of this century. The study indicates that bismuth reserves and potential resources in the rest of the world have not been adequately reported.

Jan 1, 1970

By M. D. Carver

This publication describes development by the Bureau of Mines of a quality evaluation procedure for certifying the adequacy of production lots of Kroll process zirconium sponge the Bureau had produced for reactor applications. After the procedure was devised, the next step was to apply it in controlling the quality of one-half million pounds of zirconium sponge com-prising 259 production lots, called blends, originating at the Metallurgy Research Center of the Bureau at Albany, Oreg. The Bureau concluded that the evaluation method developed was adequate and that by this method the zirconium blends having impurity levels or other property values outside specification limits were differentiated and thus were diverted from nuclear energy end uses. The research was performed under contract for the Bureau of Ships, Department of the Navy, and for the Atomic Energy Commission (AEC).

Jan 1, 1960

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The tactual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the twelfth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate halt-township map. The description of each half township is followed by a description of each deposit developed in that halt township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980

By H. E. Perlee

Autoignition temperatures and limits of flammability of nine halogenated hydrocarbons in atmospheres of air, oxygen, and nitrogen tetroxide were measured in a modified standard autoignition apparatus and limit-of-flammability apparatus previously developed at the Bureau of Nines. Of the nine halogenated hydrocarbons investigates--bromochloromethane, bromotrifluoromethane, bromochlorodifluoromethane, 1,1,2-trichlorotrifluoroethane, 1-bromo-l-chloro-2,2,2-trifluoroethane, dibromodifluoromethane, l,2-dibromo-1,1,2,2-tetrafluoro-ethane, 1,1,1,3,3-pentachlorotrifluoropropane, and l-bromo-2,4-dichloro-1,1,2, 3,3,4-hexafluorobutane--two formed flammable mixtures with nitrogen tetroxide and six with oxygen; none formed flammable mixtures with air. Three of the halogenated hydrocarbons formed no flammable zones with any of the three oxidizing atmospheres. For those halogenated hydrocarbons that supported combustion in oxygen atmospheres, explosion pressures developed during constant-volume burning of mixtures near the middle of the flammable zone were observed to range from about 6 psig for dibromodifluoromethane to 158 psig for 1-bromo-1-chloro-2,2,2-trifluoroethane. In all cases, the calculated burning velocities of these mixtures were less than 8 in/sec.

Jan 1, 1966

By L. B. Pankratz

Thermodynamic data on the elements and oxides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?HP, ?Gf°, and log K are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically. Examples of calculations using these data are given.

Jan 1, 1982

By Lito C. Mejia

Diesel-powered equipment operating in a gassy underground mine could conceivably ingest a methane-air mixture from the mine atmosphere that could cause the diesel engine to overspeed, or exceed its rated speed. Engine overspeed, particularly if extreme (engine runaway), could result in personal injury, a possible mine explosion, and/or catastrophic engine failure. In this report, the Bureau of Mines reviews the literature on the potential hazards of methane-induced diesel engine overspeed. Also included are the Bureau's findings from consultations with representatives of the diesel engine industry to determine the specific engine behavior that could he expected under the overspeed condition. The report summarizes data on mine accidents involving methane, discusses results of tests on the compression ignition of methane in diesel engines, and examines fuel governors and intake-air-cutoff devices, two kinds of devices used to prevent overspeed. Analysis of the information gathered suggests that the conditions necessary to cause a diesel engine to overspeed uncontrollably are not likely to occur, particularly if the engine is equipped with flame-proofing devices. The available literature and lack of actual overspeed case histories suggest that the safety devices currently in use are sufficient to prevent diesel engine overspeed.

Jan 1, 1984