Search Documents

By Abdurrahman Cetinbas

The periphery of longwall panels in the Pocahontas No.3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray system.

Jan 1, 1974

By J. Mitchell Linne

The principal mineral commodity in the Orleans Mountain RARE II area (No. 35019) is gold. Gravel deposits along the Salmon River contain placer gold. Lode gold with associated silver is contained in quartz veins. Many placer mining claims have been located within the study area in the Salmon River district. Four placer patents totalling 230 acres were issued for claims on the Salmon River between Lewis Creek and Forks of Salmon. On this same reach of river, adjoining and overlapping the study area boundary, approximately 3.3 million cu yd (2.5 million cu m) of gold bearing gravel with values ranging from $0.51 to nearly $5 per cu yd (50.66 to $6.50 per cu m) (gold valued at $400 per troy oz), are contained in three placers, the Bloomer, Pot Luck, and Horn (table 1). Within the study area boundary there are approximately 950,000 cu yd (726,000 cu m) of gold bearing gravel in these three placers. These three mines yielded nearly 12,000 oz (373,000 g) of gold and more than 300 oz (25,000 g) of silver between 1872 and 1913.

Jan 1, 1982

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

By M. P. Board, J. K. Whyatt, T. J. Williams

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mime in the Coeur d'Alene Mining District of northern Idaho. In the present study, the energy release rate (ERR) index was used to evaluate three underhand stope backfill parameters--cement content, density, and placement gap-to determine their influence on rock bursts. This index provides a relative measure of the likelihood of rock bursting for a given rock mass. It is known that the elastic idealization of the rock mass inherent in this method causes underestimation of stope closure and hence underestimation of the influence of backfill on rock bursting. However, this evaluation still showed that (1) changing from present practice to one in which backfill was omitted altogether would increase the ERR by 42 pct and (2) perfect placement of backfill would reduce the ERR below present practice levels by 28 pct. The easiest step toward perfect placement would be elimination of the placement gap, which accounted for half of the difference in ERR between present practice and ideal placement conditions. There was no indication that increasing initial fill strength through increased cement content would affect the ERR.

Jan 1, 1992

By Dale William Avery

Thirty mines and prospects were studied; 22 are within the Dolus Lakes RARE II area. Three properties within the area and one adjacent to it were determined to have indicated or inferred gold, silver, or molybdenum resources (fig. 1 and table 1) associated with quartz veins and shear zones or quartz-pyrite stockworks in granodiorite. Five other properties in the area and three just outside have potential for the discovery of gold and silver resources. Minor amounts of very fine-grained placer gold are in glacial outwash in and near the area. The John G. Carlisle Mine (fig. 1, no. 9) produced 120 oz (3.7 kg) of gold between 1897-1899. The Independence Mine produced 481 oz (15 kg) gold, 197 oz (6.1 kg) silver, and 189 lb (86 kg) of copper between 1926 and 1935. These mines are adjacent to the study area's northern boundary.

Jan 1, 1983

By Laurance L. Oden

The Bureau of Mines is developing nickel catalysts for converting synthesis gas derived from coal to synthetic natural gas. The present report describes the relationship between the composition of aluminum-nickel alloys in the composition range NiAl3 to Ni2Al3 equilibrated at 840° C and the properties of catalysts obtained from them. Methanation activity was determined in the temperature range of 300° to 360° C in a flowing gas stream containing 1 pct CO, 8 pct H2, and the remainder He. One part per million of H2S was added to the gas stream at 400° C to evaluate the susceptibility of catalysts to sulfur poisoning. The total surface area was measured by the adsorption of nitrogen at liquid nitrogen temperature, and the active surface area was measured by the adsorption of hydrogen at room temperature. Total surface area and active surface area were found to increase with increasing proportion of aluminum-saturated Ni2Al3 in the precursor alloy, but methanation activity and resistance to poisoning by H2S were nearly constant. However, the methanation activity of the catalyst prepared from stoichiometric Ni2Al3 was less than half that of the other catalysts.

Jan 1, 1978

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By Thomas J. Peters

The Goat Rocks RARE II further planning areas contain no known mineral resources and have very low mineral potentials. County mining records show only one mining claim area; however, no mineralized material was found at the described location. Andesite suitable for building stone may be present, but similar material can be quarried more economically elsewhere. Several anthracite coal prospects are near the area, but the likelihood of finding an economic deposit of coal or other fuel is very low.

Jan 1, 1981

By Maurice E. Bailey

The purpose of this study is to determine worker acceptance of modified mine equipment at various intervals during a twelve month period. A survey instrument was administered to the workers by two experienced miners in four interviews. All four interviews showed a significant positive response to all modifications, except the small size of the cab of the shuttle car; however, the small size produced significant negative responses with respect to comfort in each of the four interviews. Initially, (interviews one and two), there were significant negative responses with respect to manufacturer receptivity to operator suggestions and program management follow-through on operator suggestions; however, the third and fourth interviews showed no significant negative responses with respect to these items. Likewise, there were significant neutral responses in the first two interviews; however, the third and fourth interviews showed no significant neutral responses with respect to these items.

Jan 1, 1975

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

The 53 countries that constituted Africa in 1992 accounted for a significant portion of total world output of a number of mineral commodities. However, the continent's total output for a number of major mineral commodities declined relative to the volume produced during 1991. (See tables 1 and 2.) The most conspicuous declines in mineral production from 1991 to 1992 were for cobalt and copper (declines of 28.6 % and 23.4 %, respectively), which could be partially attributed to mining and metal processing difficulties caused by political and economic disruptions in Zaire and for uranium (12 % drop), for which much of the continental production decline was ascribed to Namibian cutbacks in response to lower world prices. The severe regional drought also adversely affected the mineral industry in a number of sub-Saharan nations.

Jan 1, 1994

By Gerald T. Homce, James C. Cawley

Electrical arcing injuries are the most common form of electrical injury in mining. MSHA data show that 381 "non-contact electric arc burn" injuries occurred in the mining industry from 1996 - 2005. A more detailed study of data from 1990-2001 showed that five types of apparatus - circuit breakers, conductors, nonpowered hand tools, electrical meters and test leads, and connectors and plugs were involved in two-thirds of the lost workday injuries. Many of the protections from electrical arcing injury available to workers in other industries stem from the application of National Fire Protection Association Standard 70E - Standard for Electrical Safety in the Workplace (NFPA 70E). NFPA 70E is a generally accepted industry guideline document, but excludes underground mining from its scope. Many of its practices and procedures, however, can be applied in the mining workplace to supplement the existing electrical safety requirements of Title 30 Code of Federal Regulations. This paper describes how NFPA 70E can be applied to mining workplaces after an analysis of the mine power system electrical arcing hazards has been completed (and Hazard/Risk Categories determined) using the tables from NFPA 70E or the calculation method as described in IEEE 1584. NFPA 70E can then be used to determine the levels and types of personal protective equipment (PPE) needed to protect miners against burn injuries. Appropriate lockout and tagout (LOTO) procedures for use in the mining industry are also described. Suggestions for better selection of electrically-rated hand tools are included. Recommendations for electrical meter selection and use based on transient withstand capability are also discussed.

By J. M. West

Increased leisure time and increased interest in the out-of-doors is leading more and more families to experiment with placer mining of gold, and some- times even to going on into small-scale production. This Bureau of Mines report supplies basic information un areas of occurrence, equipment needed, prospecting, sampling, mining, and regulations concerning the possession and sale of gold. Selected references are given for further study.

Jan 1, 1971

By Sheridan J. Rodgers

Toxic fumes generated during shot firing were measured in a phosphate rock mine and a copper mine. Fumes generated during firing of explosives in the Bureau of Mines 1350 ft3 test chamber were measured also. The release of fumes from water gels, ammonium-nitrate oil mixtures and nitroglycerin based explosives was studied. Direct reading instruments were used to monitor the fume concentrations. The amount of CO produced per unit weight of nitroglycerin explosives (0.41 ft3/200 grams) was higher than that produced by ammoniumnitrate-oil mixtures (0.24 ft3/200 grams) and water gels (0.16 ft3/200 grams). The amount of NOx produced by nitroglycerin based explosives was also higher than the amount produced by water gels or ammonium nitrate-oil mixtures.

Jan 1, 1976

By Edward C. Peterson

Recent studies indicate that the United States halt substantial reserves of ilmenite, one of the major titanium minerals. However, the studies showed that sources of rutile, another important source of titanium are limited. This paper summarizes and evaluates results and conclusions reached by the various investigations initiated by the Bureau of Mines and others pertaining to the titanium mineral resources of the Nation. Domestic occurrences of ilmenite that are economically exploitable by present-day beneficiation methods are found in Florida, New Jersey, New York, South Carolina, and Virginia. These deposits are estimated to contain 50.3 million tons of titanium dioxide (TiO2). Occurrences of ilmenite that cannot be processed economically under present technological conditions are found in California, Colorado, Minnesota, Montana, Oklahoma, Oregon, Rhode Island, and Wyoming. These reserves amount to 51.1 million tons of TiO2. Reserves of rutile found in the United States are estimated to be 1.8 to 2.1 million tons of TiO2. Other than occurrences in Florida and South Carolina, rutile is found either in small scattered bodies or in deposits where the mineral cannot be recovered economically by present beneficiation methods.

Jan 1, 1966

By Terry J. Close

A mineral resource survey of the 940-square-mile (2,434 km2) Hells Canyon study area, which includes Hells Canyon Wilderness, Snake and Rapid Wild and Scenic River's, and adjoining roadless lands in Oregon and Idaho, indicates the area is highly mineralized. Thirty-four lode deposits within the study area have resources totaling about 31 million tons (28 million t) containing copper, silver, zinc, gold, and lead; another 42 lodes, not sufficiently exposed to allow resource estimates, are believed to have mineral potential. The most important deposits are copper-, silver-, zinc-, gold-, and lead-bearing volcanogenic occurrences, followed by silver-and copper-bearing contact replacement (tactite) deposits; other lode occurrences are relatively unimportant. The most important placer deposits occur at Dry Diggins; placers along the Snake River are small and scattered. The study area has extensive deposits of limestone and sand and gravel; it has little potential for energy resources.

Jan 1, 1982

I. Domestic Production and Use: In 1981, 13 companies operated 32 primary aluminum reduction plants, with 3 firms accounting for 58% of production, Washington, Oregon, and Montana accounted for 32% of the total production; Texas, Louisiana, and Arkansas 16%; Tennessee, Alabama, South Carolina, and North Carolina 17%; other central and eastern States 35%. Based on published producer prices output of primary metal in 1981 was valued at over $7.5 billion. Aluminum consumption by 25,300 firms was centered in the East Central United States. Packaging accounted for an estimated 30% of domestic consumption in 1981, building 21%, transportation 18%, electrical la%, consumer durables 8%, and other uses 13%

Jan 1, 1982

By Gerald P. Scanlan

Control of the dust produced by continuous mining machines in coal mines is generally obtained by water sprays from fixed nozzles mounted on the frame of the machine in back of the cutting head. Mounting the nozzles on the rotating head of the machine closer to the coal cutting bits may improve the efficiency of dust suppression. To test this concept, respirable dust measurements were made during 39 regular production shifts in an underground mine using a Joy 11CM continuous miner. The equipment used, difficulties encountered, and measurements obtained are described.

Jan 1, 1974