Search Documents

By Xiaoning Yang, C David Pearson, Brian W. Stump

An experimental study of ground motion from explosions designed to remove overburden in an open pit coal mine is reported. The purpose of this study is a characterization of these ground motions in the distance range of several tens of meters to several kilometers. The investigation has focused upon both single cylindrical sources with different explosive configurations as well as arrays of charges in the production mode. Critical to this study of source configuration and coupling is experimental control of the individual explosions, the timing of the explosions and the geological properties. The height of the explosive charges, their depth and charge distribution were monitored in the field. High speed photography as well as velocity of detonation measurements were made on the multiple explosion source so that detonation of individual charges could be documented.

Jan 1, 1994

By Robert Morgan

The mind-set that only blasters and their helpers need training in explosives can result in risk to other employees working at mine or construction sites where blasting is conducted. Misfires are not always immediately obvious during postblast examinations performed by the certified blaster in charge; the presence of undetonated explosives may not appear until well within the muckpile as was the case in the photo, right. To avoid accidents involving misfires, follow safety procedures specified in mine safety regulations, and the ISEE Blaster’s Handbook that include the following:

Jan 1, 2004

By Yang Jun, Qu Mei, Zheng Yao-wu, Chi Li-yuan

Due to the necessity of the prediction of blasting seismic effect around strip mine bench blasting area, the paper provides a method to predict the blasting seismic effect by employing the superposition of seed waveform at different monitoring points. The method assumes that blasting vibration waveform per hole is similar to seed waveform at monitoring point. Therefore seismic wave consists of the superposition of the waves from all of blast holes. Firstly, via sensors multiple seed waveforms can be achieved at different distances from signature hole. Then, by using the given dose and the distance, the vibration waveform of a certain blast hole can be calculated by the corresponding seed waveforms. Finally, the initiation delay time interval per hole is added to the propagation time to the predicting point. The predictive waveform at the whole blasting area can be obtained by superimposing all of the single waveforms. Considering the vibration waveform of a single blast hole changes greatly with the distance, under different distances condition the seed wave employed to superimpose is achieved from the similar distance. The experiments demonstrate that based on the method the predictive vibration waveform and spectrum are basically consistent with monitoring results around near-field blast. Compared with single seed wave method, the superposition method of multiple seed wave is more reliable to predict the duration of blasting vibration, the peak particle velocity, dominant frequency and frequency distribution.

Jan 1, 2015

By Jeffery L. Dean

Founded in 1974, the ISEE has grown to more than 3600 members representing 72 countries. The Society and its 35 chapters in the US, Canada and Australia promote research and education, provide forums for the exchange of explosives technology, serve as a repository of explosives information, provide expert help to governments, conduct certificate/training programs, and promote the teaching of the safe and controlled use of explosives.

Jan 1, 1997

By A J. Rorke, U Chhika

"A series of tests was carried out on a dry blend of PPAN and LAN prills (LANFO). The objective of thetests was to determine detonation stability and VOD performance compared to ANFO. Heave andfragmentation results in the field were also evaluated visually. A number of factors were behind for.mulating this blend. A lower cost is combined with higher in-hole energies, but at slower reactionrates and lower peak borehole pressures. The resultant effect is improved heave characteristics andlower energy losses caused by inefficient crushing of the rock immediately around the borehole.The test results indicate that IANFO is ideally suited to blasting in softer midburden and overburdenrock types often encountered in coal strip mines."

Jan 1, 1995

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

The underwater test method for the determination of energy content of explosives is a very useful method. It’s also the only one which can separate shock and gas heave energies from each other. The total energy can be determined as a sum of these partial energies. Because of this special feature, the test method can be used to develop the energy content of explosives for different purposes; the military high explosives should contain more shock energy whereas the gas heave energy is a very important feature for the blasting explosives. The goal of this study was to find out the effects of aluminium and sodium perchlorate increments to the shock, gas heave and total energy values of an emulsion explosive and detect the particle size effects of two different aluminium powders to the total and partial energies as well. Both partial energies as well as the total energy were observed to increase linearly as a function of aluminium (A-80) concentration. The fine aluminium powder (A-100) (6%) also seemed to increase the shock energy of the explosive slightly whereas the gas heave energy was observed to remain unchanged to compared to the normally aluminazed (A-80) (6%) emulsion explosive. Therefore the fine aluminium powder also increased the total energy, but only very silightly. The fine aluminium powder can probably take apart to the chemical reactions more easily during the detonation. (3%) of sodium perchlorate (NaClO4) mixed with (6%) of (A-80) aluminium powdered emulsion explosive was observed to effect to the gas heave energy content of the explosive, but only very slightly. The shock energy was observed to remain unchanged.

Jan 1, 2005

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1994

By William Wilkinson, Vladisla Kecojevic

Current three-dimensional (3D) computer design technology leveraged into drill and blast planning and operations is changing the way engineers and operations approach drill and blast design. Additionally, Global Positioning Systems (GPS) technology that is now readily available to the civilian population is being implemented into the mining sector with a variety of new products specifically designed for drill and blast operations. The objective of this article is to discuss the steps involved with 3D Computer-Aided Design (CAD) of drilling and blasting, and the benefits such a design can provide in conjunction with GPS and drill monitoring systems.

Jan 1, 2004

By Rennie Kaunda, David Streeter, John Kemeny

This paper describes a field/laboratory study that was conducted in cooperation with a mine in Arizona. The primary purpose of the study was to investigate the effect of blasting energy on the crushability and grindability of the post-blast rock fragments. The crushability and grindability of the rock fragments were evaluated through laboratory comminution tests. A secondary purpose of the study was to investigate different laboratory methods for estimating the comminution properties of the rock fragments. In particular, a number of standard rock mechanics tests were conducted and compared with the comminution test results. Finally, the study was used to evaluate new technologies for estimating insitu rock mass strength and for assessing post-blast fragmentation. To estimate in-situ rock mass strength, the specific energy of drilling (SE) was calculated during blast hole drilling utilizing a continuous drill monitoring system. Post-blast fragmentation was estimated using the Split image processing system. Results from the study support the idea that increases in blast energy can enhance crushing and grinding. Also, several simple rock mechanics tests were found to correlate well with the results from standard comminution tests, which could prove to be useful in practice.

Jan 1, 2003

By Deane Tunaley, Clint Brearley, Steven Kotsonis, Richard Goodridge, Tom Smylie

Explosives are widely used in the Oil & Gas Industry for subsurface mapping via measurement of reflected sound waves as each charge is detonated. To complete a seismic survey, several thousand explosive charges may be deployed into narrow boreholes, often in areas difficult to access or where socio-political factors may increase the risk of unlawful recovery or sabotage of the explosives. Therefore, when misfires occur, the explosives left in the ground often cannot be retrieved or sympathetically detonated safely, in which case they are “abandoned” (in-line with local regulations) potentially posing a safety and security risk.

Jan 1, 2014

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By Roberto Folcht

The obligations of the European Directive 96/82/EC on the control of major accident hazards, the so-called Seveso II Directive, became mandatory within the E u ropean Member States February 3, 1999. Explosive products have been included within the Seveso II Directive, in the categories of substances capable of generating a major accident. In addition to taking “all measures necessary to prevent major accidents,” explosive manufacturers are also obliged “to limit their consequences for man and the environment.” However, for explosives in particular, no pro c e d u res, nor specific re f e rence values for damage calculation, are given either in the Directive or in the corresponding Italian Legislation, “Ministry of the Environment decree of 20 Oct. 1998.” This article presents a simplified but scientifically rigorous approach for the first approximation calculation of the effects on the surrounding area following an accidental explosion. As an example of the method of calculation, the damage areas in a hypothetical explosives manufacturing facility, as shown in F i g u re 1, will be anal y z e d . The method proposed in this article can also be used for the analysis of explosions of gas in tanks or pipelines,

Jan 1, 2004

By D. Pickering, R. Wharton

The deadline for meeting legal requirements relating to the sale of explosives in the European Union was 1 January 2003. The paper examines the range of materials that have already been certified by the different Explosives Notified Bodies as well as recent national and European Commission decisions relating to this work. The implications of enlargement of the European Union are also discussed as is the future role of the Great Britain Explosives Notified Body in certification and assessment.

Jan 1, 2003

By Ettore Contestabile, Cameron Thomas

Implosive connectors such as XECONEXTn have been used extensively for joining electrical conductors. This implosive action of explosives has also been used in other forms of high-energy metal working with excellent results. However, the inherent blast energy of these units can cause environmental side effects (especially airblast) which may restrict their use around inhabited areas.

Jan 1, 1994

By Dennis E. Mitchell

The need to develop and field explosive, pyrotechnic and propellant initiating systems that have high reliability and extraordinary safety requirements has led to the exploration and development of several materials and initiation systems at our laboratories. Our approach to initiating device development encompasses five main areas; energetic materials development , device physics, theoretical analysis and model development and experimental verifications

Jan 1, 1995

By Jerry Wallace

The goal: At an industrial site, sever a well pipe containing an interior obstruction in a timely, cost effective manner by using a shape-charge to cut through the casing more than 50 meters below ground surface from the outside, doing so while inside a larger pipe, without damaging the larger pipe. The problem: Pumps and retrieval tools stuck nearly 50 meters below ground surface inside a 305 mm diameter by 9.5 mm wall thickness water well casing. The well, depth of 185 meters, had to be inspected for contaminates then properly decommissioned before industrial expansion could take place overhead. The limitations: A 508 mm diameter pipe had been driven around the 305 mm pipe to a depth of 63 meters. The usable internal diameter of the larger pipe was about 480 mm while the smaller pipe had buckled at one point forming a 350 mm wide spot. The charge thickness was limited to less than one-half the difference. Additionally, water that filled the annular space between the two pipes had to be displaced for the charge to work properly. The solution: Enlist the support of the shape-charge manufacturer to design, build and test a charge to work under the conditions present, then make it work in the field.

Jan 1, 2000

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous, quantified feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool in evaluating the success of ground preparation practices. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile d&ability. This approach is considered to provide a very comprehensive survey of post blast conditions since the shovel must physically interact which every cubic yard of blast fragmentation.

Jan 1, 1991

By Cristian Rodriguez, Tom BoBo, Maria Rocha, John Kemeny

Blast fragmentation depends on many factors. First of all, it depends on the specific blast design, which includes the amount and type of explosive, the blasting pattern, the timing and sequencing, and other parameters. Secondly, it depends on the properties of the rock mass, including the uniaxial compressive strength (UCS), the rock mass elastic modulus (E), the rock discontinuity characteristics (as reflected in the GSI or RMR), and the rock density. Several fragmentation models have been proposed to predict blast fragmentation based on the blast design and the properties of the rock. These models include the Kuz-Ram model and variations of this model, as well as recent models by Kim and Kemeny (2011) and others. Fragmentation models are validated and calibrated by comparing the predicted fragmentation with actual post-blast fragmentation from image processing monitoring systems.

Jan 1, 2014

By Gregg A. Scott, Gordon F. Revey

"The Folsom Dam is a 340-foot-high concrete gravity dam with embankment wing dams located on the American River about 20 miles northeast of Sacramento, California. Folsom Dam is operated andmaintained by the U. S. Bureau of Reclamation (Reclamation). As part of the Central Valley Project,Folsom Dam is a multipurpose facility providing water supply storage, flood control, power generation, and recreational opportunities."

Jan 1, 1999