Search Documents

By H Fukui, K Ichikawa, K Aikou, E Suzuki

An electronic delay detonator (EDD) consisting of a digital-base electronic delay module and a conventional instantaneous detonator module, designed for series connections with a special adjustable-output blasting machine, is described and shown to provide a delay time accuracy some four to twelve times higher than that of pyrotechnic millisecond and decisecond delay detonators, together with the other performance characteristics necessary for practical use. Also described is a blasting design system which allows effective reduction of ground and air vibration, through the use of EDDs with optimum delay times as determined by accurate computer simulation based on wave form and other data obtained from an on-site single-shot test blast.

Jan 1, 1989

By Winston Wilches B., Scott Scovira

This paper discusses recent changes to the emulsion blend blasting agent used at the Drummond Pribbenow Mine in Colombia, one of the world’s largest open pit coal mines, and the resulting improvements in rock breakage and excavator productivity. Based on field evaluations, the use of High Density Ammonium Nitrate (HDAN) can be effectively implemented in an emulsion blend blasting agent, yielding excellent results in terms of energy release, shelf life and velocity of detonation (VOD). Field evaluations showed that formulations using HDAN exceed the performance of the actual 50%/50% emulsion/ANFO blend using Porous Prill Ammonium Nitrate (PPAN). PPAN is conventionally used for emulsion blend manufacturing, with physical characteristics to facilitate sensitivity during the detonation process.

Jan 1, 2014

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Peter Moser

The average annual consumption of raw minerals in Europe is 10 ton per person. About 50 % is produced by blasting. For a population of 450 million (including the population from the countries of the new member states) this makes 2.25 billion tons of blasted rock, 80 % being building industry aggregates and industrial minerals. In aggregate quarries 10-15 % of the rock blasted can’t be sold, as the material is too fine, i.e. smaller than 4 mm. This ‘fines problem’ is worse in the quarries of limestone and cement producers where up to 30 % of the material is useless. Thus about 450 million tons of useless rock fines are produced and put on waste dumps every year, i.e. 1 ton/person. This problem is addressed by the research project LESS FINES - “Less Fines production in aggregate and industrial minerals industry” which is funded by the European Union under the project contract G1RD-CT-2000-00438. The project consortium, formed of nine partners from 5 EU countries, works on the following two main research subjects: 1. The determination of the natural breakage behavior (NBC) of the rock mass, which is defined as the particle size distribution curve for a certain rock mass with the maximum uniformity and thus for a given maximum particle size that fragmentation curve which gives the minimum amount of unusable fine material. The comparison between the NBC and an actual blast fragmentation curve allows to quantify the fines reduction potential. 2. The adaptation of explosives properties, charging techniques and timing in order to produce only the minimum, inherently unavoidable percentage of fines. With about 15 full time working persons the project is estimated to be one of the largest blast related research activities in Europe at the time of the project period. The project is coordinated by the Department of Mining Engineering& Mineral Economics of the University of Leoben.

Jan 1, 2004

By Fumihiko Sumiya, Yukio Kato, Yoshikazu Hirosaki

Secluential blasting is one of the most popular methods in blasting. tiowever, it is well known that an emulsion explosive can be dead-pressed by dynamic pressure generated by the previous detonation. It is difficult to gain the expected blasting performance due to tb.e malfunction of explosive caused by deadpressing and shock desensitization. Such malfunction of an explosive is undesirable for safety blasting operation. Voids in the emulsion explosives will considerably affect the performance of explosives such as sensitivity, detonation velocity (DV), pressure-resistance and so on. To clarify the detonability and the performance of precompressed emulsion explosives, the DV was measured. Three types of microballoon or micro bubble ; two types of glass microballoon(GMB), resin microballoon@MB) and chemical gas bubble ; were used as sensitizers for the sample emulsion expiosives. The underwater explosion test was carried out to load dynamic pressure into the sample explosives. The dynamic pressure was generated by the detonation of a donor explosive, and the DV of the sample explosives as acceptor was measured by ionized gap terminals. The dynamic pressure level and initiation interval for the donor and the acceptor were chosen as experimental factors. The detonability was carefully investigated at short initiation intervals taking into consideration the interaction between same delays caused by the deviation of the ignition time of the electric detonators. From these experiments, the following results were obtained ; A) The DV of precompressed emulsion explosives was low compared with that of uncompressed emulsion explosives in all pressure conditions. B) The decrease of DV in the sample explosives sensitized by GMB s was larger than that of DV in the sample explosives sensitized by RMBs or chemical gas bubbles. C) The recovery of the detonability occurred rapidly in the sample explosives sensitized by RMBs and chemical gas bubbles. However, a long period was needed for the recovery of detonability in the sample explosives sensitized by GME! s. It was concluded that the type of microballoon and micro bubble significantly influenced the detonability of precompressed emulsion explosives.

Jan 1, 2002

By Michael S. Wieland

Toxic fume concentrations from industrial mining explosives depend somewhat upon the type of rock (or other strata) confinement. Though traditional detonation theory disregards this influence, the work principal from thermodynamics reveals it, when the violent interactions that transpire within the rock blast are taken into proper account. Resolution of the work principle technique requires total thermodynamic equilibrium under constraint, so the nonequilibrium dynamics is rendered in that way, using an old trick from theoretical mechanics that revises the representation of forces. The rock pressure reduces to a four-component sum: the rock compressive strength and natural atmospheric pressure, as reckoned quasi-statically, and the gravitational influence and reversed inertial resistance, as reckoned dynamically. Tabulated specie concentrations and graphical trends reveal the dependency upon rock pressure, rock temperature and the fuel-oil percentage in ammonium nitrate mixtures (ANFO), used to illustrate the model. Rigid-wall test chambers have notable ullage (residual space), where rapid expansion influences the reaction quenching, yielding a fume spectrum unlike that for rock confinement; reported rock tests are therefore used for comparisons. For the thermodynamic regime where quenching occurs, seven concentrations are resolved, including carbon monoxide (CO) and total nitrogen oxides (NOX). Their trends yield inferences regarding the way unwanted charge desensitization from transitory hole-to-hole wave impact in conjunction with reduced rock pressure can yield nasty toxic fumes, the dark rusty cloud phenomenon!

Jan 1, 2005

By Joseph L. Uraco, Harry C. Verakis

The use of explosives in underground coal mines presents a potential risk for serious injuries and death to miners. Widespread disasters have occurred from the explosion of methane and/or coal dust initiated by blasting with explosives. Many of these disasters took place in the early 1900's when the use of black powder for blasting was prevalent. Historically, the investigations in the U.S.A. to develop and test safer explosives for blasting coal began in 1908 when a testing station was established in Pittsburgh, Pennsylvania. Since that time, great strides have been taken in the development of safer explosives. The use of safer explosives has significantly reduced blasting accidents in coal mines. Enactment of legislation, such as the Federal Coal Mine Health and Safety Act of 1969 and enforcement of regulations has also improved blasting safety. More recently, MSHA began a major revision of its regulations for blasting in coal mines. In 1988, MSHA published final rules for the approval and use of permissible explosives in coal mines. The approval requirements for explosives address testing and evaluation. The requirements include tests for sheathed explosives which represent a new technology. The use regulations provide increased safety protection for miners by including standards to address identified hazards. Major aspects of these standards, such as qualifications for blasters, multiple-shot blasting and the use of sheathed explosives are discussed.

Jan 1, 1992

By Lina Lopez, Jose Sanchidrian, Jean Du Mouza, Essaieb Hamdi

This paper evaluates the actual energy delivered by the explosives used in the fragmentation of rock during blasting vs. the available theoretical explosive energy. The evaluation of the fragmentation energy of the blast is first done. Fragmentation by blasting can be seen as a process in which creation of new surfaces within the rock mass is made by generation of new cracks or extension of pre-existing ones. From this idea, the fragmentation blast efficiency can be assessed as the fraction of the available explosive energy used for creation of new surfaces. The evaluation of new cracks area created by the blast is based on the SIMBLOC methodology and the corresponding fragmentation energy is then obtained by the Griffith theory. Secondly, the amount of energy delivered down to a certain pressure or volume along the detonation product expansion process, given by the useful work, is calculated. This is done by first determining the CJ state of the reacted explosive and subsequently performing an adiabatic expansion calculation of the detonation products from that state. W-Detcom code has been used for the calculations using the BKW equation of state with the Sandia parameter set. The fragmentation energy and the useful work are calculated for blasts performed in two mines in Spain. Multiple regression is applied to the results in order to give an assessment of the better description of the explosive energy .

Jan 1, 2002

By L M. Stodart

In the increasingly competitive environment of the 1990's, there is a need to provide the users of explosives with accurate and immediate information. Research has shown that information technology alone will not provide companies with a sustainable competitive advantage. However, where information technology is used to assist the development and enhance the performance, of the employee sustainable competitive advantage can occur. A Performance Support System is a tool that combines explosive's theory, government regulations, and site specific knowledge in an easily accessible computer program. In this paper five areas are addressed where a Performance Support System can assist the user: as a reference source, in an assistant or advisory role, as a instruction aid, in regulatory compliance, and as an operations monitor.

Jan 1, 1993

By J R. Brinkmann, S G. Giltner

Nearly all of the South African gold mining industry still uses fuse and igniter-cord initiation systems. Over the past 30 years numerous attempts at developing new initiation systems have not yielded a viable alternative. New initiation systems for narrow stopes are currently being developed by various concerns and the likelihood of these efforts producing feasible alternatives is greatly improved due to the recent advances in electronics technology. The greatest potential benefit of alternative initiation systems is increased production rates through improvements in accuracy and reliability of firing over that of fuse/igniter-cord. Another important feature is the capability of millisecond delay firing as this can lead to reduced stope cleaning times by way of enhanced rock throw and improved fragmentation characteristics.

Jan 1, 1989

By Michael E. Kovach

This discussion is an overview of an approach to drilling and blasting angle holes at Martin Marietta Aggregates. Method of determining burdens, hole depths, angle settings and explosive selection will be discussed in detail with an emphasis on safety and production. Such techniques and methods involve the use of hand-held surveying instruments such as the Abney level, pocket transit and inclinometer along with measuring tape and burden pole. An interesting method developed by Oscar Banfield a retired Martin Marietta and E. I. duPont engineer, for setting the proper angle on a drill will also be presented. This treatise is a discussion of the use of simple yet important tools and techniques a blaster should use to resolve both routine and complex problems encountered during quarry blasting operations.

Jan 1, 1992

By Edward J. Walter

A vibration record is a complex of motions resulting from a combination of direct, reflected and refracted seismic energy that originated at a blast source. Multiple hole blasting using delays further complicates the motion in that overlapping of seismic wave trains may occur when delays do not fire in the programed sequence. This can result in variations in amplitude, frequency and wave-1ength of the vibration. Amplitude may be doubled, frequency may oscillate between the highest and lowest frequencies present and wave-length may approach doubling of the longest wave-length present. These effects can present serious problems to conducting a safe blasting program since increased amplitudes and lower frequencies present higher damage potentials for structures. The development of these effects is described and illustrated graphically to show how these effects can occur.

Jan 1, 1989

By Wendell W. Harris, Stanley J. Vitton

In the United States each year it has been estimated that expansive soils cause approximately $9.0 billion in damage to buildings, roads, airports, and other facilities. This figure alone exceeds the damage estimate for earthquakes, floods, tornadoes, and hurricanes combined. Unfortunately, some cases of expansive soil damage (swelling) are blamed on rock blasting operations if the blasting operations are located within the immediate area. While simple tests, such as the Atterberg limits test, can characterize a soil as expansive, it does not necessarily answer the question whether the foundation soils are causing distresses to a structure. In particular, it appears that once a soil has been labeled as nonexpansive it is no longer considered as a problem soil, in which case blast vibrations become the prime suspect.

Jan 1, 1996

By Koichi Kurokawa, Takeo Ueda, Masahi Nakano, Yoji Tasaki

A lightning strike generates several 10kA and several billion volts, and earth currents generated by lightning is dangerous to some underground and all surface blasting operations. In order to evaluate the safety against lightning in conventional electric firing method and electromagnetic induction blasting system, a test is conducted by connecting a wire with an impulse generator. Frequency of impulse current used in the test is 17kHz and the waveform is a vibration type and the duration time is 250 ~usec. The results of the test show that induced current increases with the increasing of impulse current. In the case of MBS connection, when maximum primary current is 1700A, Maximum secondary current is 11.8A and the electric detonator is fired at this condition.

Jan 1, 1988

By Ian A. Niell, Alastair C. Torrance

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation velocities of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation measurement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 1509. However, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1990

By Mo Jadbabaei, Scott Harrison

There is very limited information available regarding the air pressures, flow rate, and velocity profiles in blast hole air drilling applications. Currently, many people are using incompressible flow correlation to calculate the bailing velocity. In this article, air pressure, flow rate, and velocity profiles are calculated using compressible flow theory. The airflow at the bottom of the hole is simulated using the jet flow theory. The concept of choking condition is introduced, and it is concluded that the velocity at the nozzle exit cross section cannot exceed sonic velocity. The minimum pressure required for achieving choked condition at the nozzle cross section is calculated. Choked and overchoked flow conditions at the nozzles are examined, and the maximum achievable cleaning power is correlated to the nozzle size and pressure.

Jan 1, 1999

By Dale Preece, Stephen Chung

Development of DMCBLAST-3D is continuing and now includes the capability to simulate the detonation of multiple blastholes in multiple rows that make up a conventional bench blast, either in a rock quarry or a surface coal mine. DMCBLAST-3D is a three-dimensional extension of the proven twodimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2002

By John W. Kopp, David E. Siskind

Over 4 billion pounds of commercial explosives are used by the U.S. mining industry every year with an excellent and improving safety record. However, accidents involving explosives are seldom minor. They produce a disproportionate amount of fatalities compared to other mining activities, as reflected in the relatively high severity rates. The U.S. Bureau of Mines (USBM) has been analyzing blasting accident data obtained from the Mine Safety and Health Administration (MSHA) to determine the most frequent causes of mine blasting accidents, examining trends in these accidents, and identifying areas of needed research. This paper is an update of three previous blasting accident studies conducted on 4-year intervals by the USBM and published in 1983, 1987, and 1991, and is based on a total of 869 blasting accidents.

Jan 1, 1995

By N Vijay Mohan, K V. Balamukund, G Ananth Ramulu

Jointing of steel rods in reinforced concrete structures needs careful consideration as it renders the structure weak at the joint. The jointing is usually done at sections of structural members, where the bending moment and shear force are least. Jointing is done either by overlapping the rods or welding or by mechanical splicing. A novel method of jointing them is by inserting the two rods in a steel sleeve and cladding it on to the rods by subjecting the sleeve to explosive energy. A rod jointed in this fashion is tested for direct tension and bending when used in a reinforced concrete beam. The test results show that it is an effective method. The advantage is that a number of joints can be made in a single operation.

Jan 1, 1993