Search Documents

By Hristo Stanchev, Veselin Mehandzhiyski, Sashka Kozhuharova, Stefan Stamenov, Alexandar Penchev, Nikolay Nestorov, Velika Stamatova, Ekaterina Todorova

"This article presents the results of comprehensive research on the quantitative distribution of gold content in the raw ore and tailings from the flotation enrichment process at the Ellatzite Med plant. The study is a quantitative and qualitative determination of the presence of gold in the ore processed by Ellatzite Med AD, as well as its behavior and distribution in the various metallurgical products of the flotation process. The representativeness of the samples taken is ensured by the frequency of sampling: four work shifts of sampling on different days within a period of four consecutive weeks. The form of gold present is determined both in the analyzed samples and in separate fractions - granulometric, magnetic, electromagnetic, heavy and light. A summarized diagram presents the phase distribution of gold in the final products of the dressing process. The results obtained are used for further analysis and evaluation of the actual technological parameters of the gold. It was established that an increase in the initial gold content, respectively in the content of native gold in the raw ore, with the current process, leads to an increase in gold losses, mostly in the native gold phase. The conducted analysis of the results from the comprehensive tests on determining the form of gold present in the various enrichment products gave rise to further research with the use of a Knelson centrifugal concentrator."

Jan 1, 2014

By E. V. Mezentseva, S. M. Okunev

"In the article there is set forth a development experience of JSC LEBEDINSKY GOK Beneficiation Plant concerning the plan of increase in the production volumes of the iron ore concentrate with Fe content more than 69.5%. There are considered the issues regarding implementation of the updated process scheme of the concentrate beneficiation using fine screening operation, its industrial tests have shown an exploitability of this development direction. There are described the issues relating to the ceramic filters for dehydration of the additionally-beneficiated concentrate, there are given the production and process figures achieved during the exploitation. The methods of the research. In the paper there have been used the following scientific research methods: the methods of system analysis, mathematical statistics, classification, comparison, modelling, observance, experiment. INTRODUCTION JSC LEBEDINSKY GOK is the largest leading enterprise for iron ore beneficiation and the unique RF producer of the merchant hot briquetted sponge iron (HBI) highly demanded by the consumers. Raw materials for hot briquetted iron production are fluxed pellets produced from iron ore concentrate with Fe content more than 69.5% (additionally-beneficiated concentrate). Strategic program of the plant’s development foresees expansion of production of the highly demanded products that imposes a necessity of expending capacity of the enterprise and implementation in production of modern processes and equipment having low resource intensity and ensuring in addition a high efficiency. Construction of the third stage of the HBI Plant became one of directions for the strategic development of JSC LEBEDINSKY GOK implemented in 2017 that caused a demand in the production volumes and filtration of the iron ore concentrate with Fe content more than 69.5%. Purpose of the work – to develop and to provide a rationalization for efficiency of the production process and filtration of the iron ore concentrate with Fe content more than 69.5% ensuring increase of production volumes and its prime cost."

Jan 1, 2018

By Mark Viduetsky, Dmitry Tropnikov, Victor Maltsev, Victor Sokolov, Alexander Purgin, Andrey Panshin, Alexander Bondarev, Pavel Kozlov, Igor Garifulin

"CFM pneumatic flotation machines were developed by the Institute of Materials Science and Metallurgy, UrFU, and designed to concentrate a wide range of ores and man-made materials. A key principle of work is pulp preparation for flotation owing to its saturation with finely dispersed air bubbles in ejectors. CFM plants, their advantages over domestic and foreign prototypes are described. CFM pneumatic machine commercialization resulted in: - machines demonstrated high floatation efficiency for concentration of rebellious pyrrhotite-bearing copper and zink by simultaneous floatation of copper and zinc minerals and depressing pyrrhotite. CFM- 1400M introduction allowed simplifying and optimizing the flow chart and increase extraction of copper - by 5.4%, zinc - by 9.5% and improve the quality of copper (3% Cu) and zinc (1.5% Zn) concentrates. - due to copper pyrite concentration by using CFM 1400M overall copper recovery was increased by 1.5 %, and the content of copper in concentrates - by1%. According to the results of pilot runs, the use of CFM flotation for zinc cakes concentration strongly intensifies the process of cleaning water-soluble metal compounds and, thereby, increases the efficiency of flotation concentration and subsequent milling. CFM machines showed higher specific capacity (three or four times higher) (both for feed material and froth product). Specifically, CFM froth product has higher content of useful elements (silver by 0.014 % abs. zinc by 0.31% abs.) and better extraction (silver by 6.08% abs., zinc by 0.31% abs., and sulfide sulfur by 13.7 %). Sulfide sulfur content of CFM product chamber as compared to mechanical flotation machines is two times lower (0.48 vs. 0.95 %)."

Jan 1, 2014

Results of the study of chloride ion concentration effect to osmium-187 sorption from wastewater of copper smelter with use of foreign anionites of different basicity and structure are presented in the work. It was found that the increase of chloride ion concentration in the wastewater helps to increase recovery of osmium using anionites regardless of their nature. The ways to intensify the process are proposed. The method for osmium elution from the anionites with potassium iodate solution was developed. It was shown that the method lets to recover up to 99% of osmium from the anionites. Recommendations for selection of eluents for better recovery of osmium from the anionites were elaborated. Keywords: wastewater, osmium, anionite, sorption, chloride ions, eluent, recovery

Sep 1, 2012

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By A. L. Hinde

The steady-state and dynamic behaviour of semi-autogenous grinding (SAG) mills are arguably best described using a population model that caters for the breakage kinetics and the material trans-port of rock and pulp inside the mill. Breakage kinetics are usually expressed in terms of a specific breakage rate function and a separate primary breakage distribution function. Material transport usually invokes the concept of a specific discharge rate function. Unfortunately, the breakage rate and breakage distribution functions for SAG mills are very difficult to estimate uniquely from plant data alone. Simplifying assumptions must be made to over-come this problem, which leads to many unresolved dilemmas with regard to whether or not the de-rived functions are accurate, precise, and reflect reality. For example, it is sometimes assumed that the breakage distribution function for a SAG mill treating run-of-mine ore can be derived from laboratory dropweight and tumbling tests on small rocks in narrow size ranges. Such tests hardly reflect the environmental conditions likely to be encountered in a pilot or production SAG mill where there is a wide spectrum of particle sizes. It is shown that the dilemmas associated with standard population balance models (models that utilise separate breakage rate and breakage distribution functions) can be overcome by expressing breakage behaviour inside a SAG mill in terms of a single function. This function is an energy-based cumulative breakage rate function defined as the fractional rate at which particles and rocks coarser than a given size break to below that size per unit specific energy input. A model for SAG milling is formulated, which invokes the concept of a cumulative breakage rate function. Comparisons are made between the mathematical structure of this ?simple model? and standard population balance models. Perhaps the most attractive feature of the ?simple model? is that the cumulative breakage rate function can be uniquely estimated from measurements of size distributions and mass flows of the feed and discharge streams together with the size distribution and holdup mass of the mill charge. Such measurement can easily be made at pilot scale. It is concluded that this simplified approach to SAG milling may turn out to be the quickest way to fully describe and quantify the performance of these very complex mills.

Jan 1, 2014

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By D. J. Zhao

The reduction of ilmenite pellets was investigated at 950°C and 1000°C under a CO-N2 gas mixture with 10 L/min gas flow rate. All the reducing reactions were conducted in a furnace with a thermogravimetric analysis system. The reduction rate is higher at 1000°C than that at 950°C. At the early stage of the reactions, with the CO concentration increasing in the gas mixture, the reduction rate increased at 1000°C. In addition, at the early stage of the reactions, a rapid temperature increment and a rapid conversion of oxygen were observed on the curves of temperature versus time and conversion of oxygen versus time under different experimental conditions. The solid reaction products obtained in these experiments were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectrometers (EDS). Metallic Fe with small amount of Ti dissolved in it and oxides of Ti were found in the solid reaction products, but the formation of any nitride phases was not found under the prevailing conditions.

Jan 1, 2014

By Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

The possibility to develop an efficient recovery and reuse of concrete materials from Demolition Waste (DW) represents one of the main targets applied to end-of-life constructions dismantling/recycling. The need to recycle end-of life concrete materials is strongly increasing in these last years for several reasons: i) the decrease of steady supplies of good quality natural aggregates, ii) the need to secure ample supplies of concrete aggregates to the construction industry and, finally, iii) the environmental constraints limiting the DW wastes disposal. The fulfilment of these goals produces several benefits, that is: i) a reduction of new resources consumption, ii) a strong reduction of the costs linked to transport and energy production, iii) the possibility to utilize materials, otherwise lost (e.g. land filled), iv) land preservation and, finally, v) the reduction of the environmental impact of new exploitation activities. A lot of efforts have been addressed to develop, set-up and apply innovative technologies to maximize DW conversion into useful secondary raw materials. The possibility to utilize efficient, reliable and low cost analytical tools to perform detection/control actions: i) to assess concrete characteristics, before demolition, and ii) to detect the presence of contaminants in coarse aggregates (e.g. bricks, gypsum, steel, glass, plastics, wood, etc.) represent the key issues to fulfil in order to develop innovative process/control actions/procedures inside the DW sector. In this paper a new technology, based on HyperSpectral Imaging (HSI) sensors is investigated to develop suitable and low cost strategies finalised to define and implement innovative smart detection engines for sorting and/or DW flow stream quality control, addressed to perform recovered materials and/or products certification. The proposed sensing architecture is fast, accurate, affordable and it can strongly contribute to bring down the economic threshold above which recycling is cost efficient.

Jan 1, 2014

By Peter J. Scales

The recovery of water for re-use in minerals processing is an important issue in the reduction of water use in mining, as is the dewatering of tailings to reduce the propensity of ?wet? tailings dams. It is common in these dewatering operations to use thickeners whereby polymeric flocculants are combined with the dilute feed to the thickener to aid sedimentation and the subsequent consolidation of particulate materials. Thickeners are the workhorses of water recovery and tailings dewatering and although the basics are well understood, there is still no ability to reliably predict the throughput and underflow density from a thickener based on traditional sedimentation tests and flux analysis. The reasons for the discrepancy between full-scale operations and predictions based on laboratory tests are numerous, including difficulties in mimicking the flocculation conditions experienced in the field and the shear conditions in the thickener. The latter effects are little understood and hard to quantify and include effects due to flocculated aggregate densification, complimentary shear and compressional effects and aggregate break-up. Developing a set of test protocols to quantify the effects of densification, shear in compression effects and aggregate breakup and the subsequent contributions of each to compressional dewatering in a thickening environment has been completed for a simple model polymer flocculated particulate suspension. The data and analysis shows that aggregate densification is a dominant contributor to the difference between observed and predicted behavior based on laboratory tests. A major consideration in the analysis is the fact that common thickener operations are permeability limited and although the various effects are all important, the one that results in the fastest water release is dominant. Of interest also are the shear rate, concentration, and time dependence of the aggregate densification process. A basic model of the process has been developed along with network yielding tests conducted using rheometry. Keywords: compressional dewatering, gravity thickening, rheometry, aggregate densification, raked batch settling

Sep 1, 2012

By E. Hulthén

Crushing plants are widely used around the world as a pre-processing step in the mineral and mining industries and as standalone processing plants in the aggregates industry. Despite automation and different advanced model predictive control, a lot of the process is still managed by operators. The operators affect a lot of the performance. The numbers of the improvement they can achieve are at least as big as the advanced control algorithms?, today. Therefore, it is also important to train the operators so they know how to behave in different situations. Models for crushers and other production units have been developed during the years and the latest add is the different units? dynamic behavior being brought in, which gives the crushing plants dynamic time dependant performance. This can be used as a simulator for operators training. By connecting a Human Machine Interface (HMI) to a dynamic simulator with the models incorporated, a training environment for operators can be achieved. In this paper, a dynamic crushing plant simulator implemented in MATLAB/SIMULINK has been connected to an HMI via a PLC. The HMI is placed in a control room at the university and complemented with monitors showing sequences from the process connected to the simulations, thus creating a realistic control room for training. In the created training environment, the operators can be trained under realistic conditions. Simple training scenarios and how they could be simulated are discussed. Apart from the increased level of knowledge and experience among the operators, the time is an important factor. While a real crushing plant is still being built, the operators to be can already be trained, saving a lot of the commissioning time. Keywords: crushing, cone crusher, simulator, control room, operator, training

Sep 1, 2012

By Weiran Zuo, Narayan Krishnan, Frédéric von der Weid, Emmy Manlapig, Fengnian Shi, Klaas van der Wielen

Laboratory study has identified a new application of high voltage electrical pulse technology for pre-weakening ores. In recent years, the Julius Kruttschnitt Mineral Research Centre (JKMRC), Newcrest Mining and SELFRAG AG have conducted joint research in validation of pre-weakening of SAG mill feed through the pilot scale tests and comminution circuit simulations. Ten tons of SAG mill feed with a top particle size 150 mm were tested with two pilot scale SELFRAG machines installed in Switzerland. A simulation study using JKSimMet software was carried out to find where the high voltage pulses pre-weakening technique can be best applied in a gold-copper ore comminution circuit, based on the data of the pilot scale SELFRAG tests. A novel comminution circuit was designed, which incorporated SELFRAG to pre-condition part of SAG mill feed (9.5 to 150 mm) and to treat the circulating SAG mill pebbles. The high voltage pulse technology effectively reduced the amount of ‘critical size’ particles in the SAG mill and pre-weakened particle strength for grinding. Attributing to the nature of bi-modal size distribution and the significantly reduced F80, the simulations showed that the SAG mill had spare capacity to process part of hydrocyclone underflow from the secondary ball mill grinding circuit. The simulations indicated that the novel comminution circuit had the potential to remove two MP1000 pebble crushers and one 10 MW ball mill from the existing 2000 t/h grinding circuit. A 5 kWh/t energy reduction by adopting the novel comminution circuit in a gold-copper operation may be realized. This would result in substantial savings in operation costs.

Jan 1, 2014

By Garren Edwards, van der Westhuizen. Andre

"Due to the depletion of easily treated coarser ores, more mineralogically complex ores with smaller valuable mineral grain sizes are treated, the means to liberate these minerals lies in grinding finer (Partyka & Yan, 2007). Grinding to these fine sizes is energy intensive, and using standard ball mills are energy inefficient at these sizes (P80 < 75µm). Therefore, stirred mills are becoming increasingly prevalent in the mineral processing industry. In order to optimize these mills, the effects and mechanisms of the significant variables need to be understood. This paper investigates a laboratory scale vertical stirred mill (Deswik mill) in an ultra fine grinding application of a South African platinum ore. The operating variables that are considered are stirrer speed, media size, media filling, and slurry density. The resulting grinding efficiencies are considered in two ways. Firstly, a statistical model is fitted to identify the effect of the significant variables on grinding efficiency, and secondly, the grinding efficiencies are also considered in terms of a stress energy model to determine whether this can partly explain the grinding mechanism in this mill. A factorial design of experiments was used on three levels for each variable, such that only linear interactions, second order interactions and two variable interactions are included in the statistical model. The results show that tip speed, media size, percent solids and mill filling are all significant to the grind, at differing energy inputs in the grinding process. The interaction effects of these variables are also dependent on the energy inputs. The results also found that the Kwade stress energy model is applicable to this mill and can be very useful to find the most efficient operating conditions for this system. The most energy efficient operating conditions in terms of mill speed and media size were typically somewhat below the standard operating conditions and it is expected that this is most probably done in order to increase the grinding rate, but at the expense of sacrificing some grinding efficiency."

Jan 1, 2014

By Susanna A. C. Stadler, Chris Aldrich, Jacques J. Eksteen

Slag foaming occurs in several pyrometallurgical processes. These processes include steelmaking in basic oxygen steelmaking furnaces and electric arc furnaces as well as various non-ferrous operations like sulphide smelting/converting and base metal slag cleaning. Although slag foaming in steelmaking processes has been extensively researched, little attention has been given to slag foaming in non-ferrous operations. Slag foaming phenomena are complex because often the system consists of three or more phases. With this in mind, factors previously identified as influencing slag foaming were investigated. These include the slag basicity, physical properties of the slag, namely viscosity, surface tension and density, the formation of particles due to undercooling of the slag and the FexO concentration in the slag. The effect of increasing FexO concentration was found to decrease the foam index due to lower viscosities, but higher surface tension depression appears to have led to increased foam index values at high FexO concentrations. The foaming index decreases with increasing basicity, until precipitation of solids occurs. After this point, the foaming index was found to increase with increasing basicity due to increased solids precipitation. In general, increasing amounts of slag-wettable solids led to higher foam indices, but the precise nature of the effect on slag foaming was dependant on the nature of the solid precipitate.

Jan 1, 2003

By M. C. Harris

"In the flotation process the contact angle is an important indicator of the hydrophobicity of a mineral particle. There is considerable literature showing that the contact angle increases when the chain length of the alkyl group associated with the collector molecule used to render the valuable mineral particle hydrophobic increases. The extent to which an alkyl group interacts with surrounding water molecules is quantified thermodynamically by the excess Gibbs energy. In the present paper it is shown that there exists generally a strong linear relationship between the excess Gibbs energy of the alkyl group associated with the collector and the contact angle. The structure-activity of such alkyl groups is in turn related to the total surface area, molecular volume, the molar volume, molecular weight of the functional groups in the molecule and interaction energies. It is proposed that the demonstrated relationship is indicative of the role which the alkyl group component of the collector, which is attached to the mineral particle, plays in increasing the extent to which water molecules at the surface of the mineral are rejected from the surface thus increasing the contact angle. The relationship between excess Gibbs energy and surface tension is further explored with a view to relating the observations quantitatively to the parameters in the Young equation.INTRODUCTIONThe issue of wettability of materials is of great importance to many industrial applications. Wettability studies usually involve the measurement of contact angles which indicate the degree of wetting when a solid and liquid interact. As is well known the contact angle (O) is the angle between planes tangent to the surfaces of the solid and the liquid at the wetting perimeter which is the zone where the air, water and solid phase merge. When the air bubble attaches to the solid surface there is an increase in the air/solid interface area and a decrease in the solid/water interface area. For attachment to occur the cosine of the contact angle should be less than 1 and this will be promoted if the interfacial surface tension between the air and the solid (? SV) is low. Classically the relationship between these parameters has been expressed through the Young equation (1) for a perfectly flat surface:"

Jan 1, 2018

By Mohammad Kor, David Beattie, Agnieszka Mierczynksa-Vasilev

The selectivity of polymer adsorption in mixed mineral systems is the basis for polymer depression of gangue minerals in flotation. Effective polymer depressants not only reduce gangue mineral recovery, they also have minimal effect on the recovery of the value phase, presumably through targeted adsorption on the gangue phase, and minimal uptake on the value phase. Traditionally, polymer depressant design has been guided by single mineral phase adsorption tests, with affinity and maximum adsorbed amount determined for gangue and value phases separately. However, there is a need to determine the actual extent of adsorption on the gangue phase while in the presence of the value phase. In this work, we report on the development of in situ atomic force microscopy (AFM) imaging for determination of polymer depressant coverage and morphology on mixed mineral surfaces. Our group has previously used AFM imaging on single minerals to connect adsorbed layer characteristics with bubble-particle attachment and flotation outcomes. Two sample types were used to test the methodology: (i) a mixture of two crushed/ground minerals encased in resin; and (ii) a composite mineral sample containing macroscopic regions of three different mineral phases. The samples have been used to probe the selective uptake of two modified dextrin polymers (octenyl succinate anhydride dextrin). AFM images acquired in situ (while all surfaces are immersed in the same polymer solution) of each mineral phase have revealed the natural selectivity of the polymer for the mineral surfaces. In all cases, the polymers adsorb on the all mineral surfaces present, but to a varying extent.

Jan 1, 2014

By Ataollah Nosrati

Agglomeration of fine mineral particles is an important step in heap leaching processes employed for a cost-effective hydrometallurgical extraction of value metals from low-grade ores. In this study, the effect of acidic binder composition and feed ore particle size on binder dosage requirement and isothermal, batch agglomeration behavior of siliceous goethite nickel laterite has been investigated. Agglomeration tests performed with tap water and 30, 44 and 98% w/w H2SO4 solutions as binders revealed the key role of binder formulation in controlling ore particle wettability, nucleation and granule growth behavior. Both lower binder acid content and higher dosage led to greater wetting, nucleation and granule growth rates. Variation of feed ore fine/coarse particles? mass ratio dramatically impacted on binder dosage requirement for effective particle wetting, nucleation, and growth agglomeration behavior. Increasing fine (-150 µm) fraction mass content in a -2 mm feed ore, led to higher binder dosage requirement and enhanced nucleation, however the overall agglomeration rate/granule size growth decreased. In contrast, the presence of coarse (5 ? 15 mm) particles in feed ore led to (i) lower binder dosage requirement, (ii) enhanced initial agglomerate size growth rate, and (iii) reduced coalescence. For dry agglomerates of similar sizes, competent coarser feed particles led to remarkably higher compressive strength than did finer feed particles. Microstructure analyses indicated that the granules containing coarser particles exhibited a distinctive, competent core/shell (fines) structure which led to their structural reinforcement. The appropriation of the findings for optimizing agglomeration behavior for enhanced heap leaching of complex, low grade laterite ores are discussed in this context.

Sep 1, 2012

By Brian Loveday, Sandile Nkwanyana, Indresan Govender

"Recent batch experiments by the authors in a pilot scale ball mill (Ø = 0.6m) have demonstrated that a partial replacement of the ball charge by pebbles (25 % pebbles; 75 % steel balls) optimally reduces the ball and power consumption without altering the rate of production of fine material (passing 75 microns). At higher pebble volumes, the production rate of fines was reduced progressively. With the 25/75 composite charge a saving of 13 % in power consumption was achieved, and a saving of 25 % in steel ball consumption is implied. A partial replacement of steel balls by pebbles reduces the overall density of the grinding media in the charge. Taking into consideration that the production rate of fines is usually proportional to the bulk density of the charge in the mill, it would be expected that a composite charge (e.g. 25/75) would coarsen the grind and consequently reduce the rate of production of fines. Pebble wear contributes a small proportion of fines and it doesn’t provide a full explanation of why the 25/75 composite charge has no (or minimal) adverse effects on the rate of production of fines. Clearly, the production of fines across the mill is directly related to the shear and compressive power dissipation density. Accordingly, we hypothesise that the spatial power dissipation distribution meeting the minimum requirements for fines production— at the so-called active regions—are equivalent, or minimally comparable, for both the 25/75 composite and 100 % ball charge operating conditions. To test the hypothesis, we performed DEM simulations to analyse power dissipation in the active regions. 1. INTRODUCTION Comminution remains to be the most expensive process in mining operations, particularly because the energy consumed in this process accounts for 30-70 % of the total cost of a mining operation (Nadolski et al, 2014). Optimization of comminution circuits has been focussed on reducing capital and operating costs and maximising throughput capacity. For existing operations, it is often a challenge if the optimization process recommends retrofitting new ‘major’ equipment. The challenge arises from new capital cost and the difficulty of retrofitting in an existing circuit, while maintaining production (Major et al, 2001). Thus, for existing mining operations, optimization of comminution (cost and throughput) is often limited to operating conditions and/or addition of auxiliary equipment (such as pebble crushers, additional screens and high pressure grinding rolls (HPGR)) (McIvor and Greenwood, 1996; Hart et al, 2001; Powell et al, 2015b)."

Jan 1, 2018

By A. Akcil, O. Celep, C. Erust, E. Y. Yazici1, H. Deveci1

"Recycling of WEEE has already gain prime importance from both environmental and economic point of view. For the recovery of metals from e-waste, many conventional physical, bio/hydrometallurgical and pyrometallurgical processes are proposed. Economic potential of e-waste is mainly driven by its precious metal content. Physical separation methods (e.g. electrostatic, magnetic, eddy current and gravity separation) exploit the differences in the physical properties of metals and non-metals. Physical separation methods are simple and economically sound but they suffer from metal losses and ineffectiveness at fine sizes. Hydrometallurgical processes are promising owing to their relatively low cost, reduced environmental impact, potential for high metal recoveries and suitability for small scale applications. Hydrometallurgical processes can be developed for selective extraction of base/precious metals using suitable reagent systems. Sulphate-based leaching with a suitable oxidant (e.g. H2O2, O2, Fe3+) is effective for copper and other base metals. After removal/recovery of base metals, precious metals can be easily extracted using various lixiviants including thiosulphate, thiourea, cyanide and chloride. However, further research is required to develop new, cost effective and environmentally friendly processes and/or refine existing ones for leaching and, in particular, downstream processes. INTRODUCTION Electrical and electronic equipments are indispensable to modern societies with numerous applications in the field of medicine, transport, communication, education, security and environmental protection. With technological developments and innovations, the replacement of old equipment leads to ever fast accumulation of waste materials such as waste electrical and electronic equipment (WEEE or e-waste). People are upgrading their mobile phones, computers, televisions, audio equipment and printers more frequently than ever before (Babu et al., 2007; Lee et al., 2007). With the rapid growth in technology today, the life span and utilisation period of most electronic and electrical equipment has been reduced considerably with concomitant generation of huge amounts of WEEE over the past several decades. According to statistics presented by Balde et al. (2015), total WEEE produced around the world was 41.8 million tonnes in 2014 and expected to rise to approximately 50 million tonnes by 2018. Kumar et al. (2017) estimated that annual growth rate for the WEEE stream is 3–5% (Singh et al., 2016). The aim of this paper is to provide an overview of physical separation and hydrometallurgical methods available for the treatment of WEEE."

Jan 1, 2018

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018