Search Documents

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis shows that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. Co-existence of ilmenite with pseudorutile, rutile and haematite is observed in substantially varying amounts in the three deposits. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among ilmenites in different places.In processing of ilmenite through the Becher process, aeration rusting of pre-reduced ilmenite is found to be the rate limiting step thus, affecting the productivity of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half.A new route of processing ilmenite for synthetic rutile has also been developed in which, ilmenite is carbothermally reduced and then processed through plasma route. The slag thus obtained is processed further to get high-grade synthetic rutile, metallic iron and high purity iron oxide. The process has been scaled up in a continuous moving bed plasma reactor. It is technologically and economically more viable where, all the iron values are recovered as salable byproducts. This paper describes the salient features of the technologies developed for the beneficiation of ilmenite to synthetic rutile."

Jan 1, 2003

By Harshad Bhagwat

The objective of this work is to investigate the inadequacies of current CFD based methodologies of model development for predicting combustion behavior of pulverized coal in furnaces. In the present paper, a steady state CFD model was used for in-depth analysis of pulverized coal combustion. The model accounts for turbulence, coal combustion, convective and radiative heat transfer and motion of coal particles. It also uses coal combustion models to account for important processes such as devolatilization, combustion of char and the evolution of fuel nitrogen during coal combustion. The model predicts fluid flow, heat transfer, progress of combustion and pollutant formation (NOx, etc.). The model uses several parameters, which need to be tuned with experimental data, which is not only limited in quantity but also insufficient in detail. Various existing methodologies like part calibration method for tuning of the parameters are discussed. In the present work, the parameters associated with coal combustion models were tuned and validated with published data obtained from an experimental furnace using one such part calibration methodology. The results clearly show that the model predictions differed with the experimental data not only quantitatively but also qualitatively. These discrepancies were attributed to part calibration methodology. A detailed parametric study was carried out to demonstrate the importance of parameters from various classes, namely, combustion kinetics, heat transfer, process and geometry parameters, and CFD model parameters. This investigation clearly indicates that parameters from different classes have significant effect on combustion behavior. The discrepancies in current methodology are discussed and a need for comprehensive methodology is highlighted. Keywords: pulverized coal combustion, computational fluid dynamics (CFD), pollutant formation (NOx), mathematical modeling

Sep 1, 2012

By Lj. D. Andric

By the micronization-milling of the material, the size and the structure of its particles are changed and it comes to the increasing of the potential energy of the system as well as to the chem-ical activity of the material what is the result of an increased free surface and of the concentration of the grate defects, that is of the internal energy of the system. All these changes that are reached, show that new characteristics of treated materials are got by micronization process. Controlling the process of the micronization and by purpose directing of the new characteristics of the activated materials, we can have the positive effects and use them in more technologies. Talc is important nonmetallic mineral raw material that is widely used as either the basic raw material, or as filler. This has stimulated its technological investigation, as well as the investigation of its physical-chemical characteristics. In this paper are shown experimentally reached results of the physical-chemical characteristics of the talc during the process of the micronization in high energetic mill. In this paper, the optimum conditions of miconization of talc in high-energy-speed rotary mill and its influence micronization on a degree of Fe2O3recovery by hydrometallurgical methodes, are presented. The X-ray analysis of the obtained products showed that high quality talc with low content of can be obtained by these physical-chemical processes In this paper, the principles and application or fine and ultra-fine grinding high-energy attriton mill with small balls, enabling fast, efficient grinding, low energy consumption, short grinding time and easy handling will be described.

Jan 1, 2014

By P. Spolaore

In the frame of Bioshale FP6 project, the bioprocessing of a polymetallic and polymineral concentrate produced in an industrial operation in Lubin, Poland, was assessed. Following successful batch culture tests, processing in continuous conditions was tested to determine the main specifications for the application of the stirred-tank technology to this sulphide concentrate from black shale ores. The experimental work was carried out in a laboratory-scale unit consisting of 3 stirred tanks (50L or 20L) using an acidophilic and moderate thermophilic bacterial population. Different configurations of the unit and key operating parameters were tested (nutrient medium composition, solids concentration, rates of agitation and aeration). Scientific and technical approaches, such as bacterial community structure and mineralogical analysis were implemented in order to better understand the chemical and biochemical reactions occurring in the system. Using the data produced during the continuous operation, downstream processing assessment for both copper and silver recovery was also carried out. The best copper recovery obtained in the continuous operation was 92% and a hot brine leaching of the bioleach residue (PLINT process) allowed to recover 92% of the silver. A preliminary tech-no-economic evaluation of Lubin concentrate bioprocessing including bioleaching, copper and silver recoveries demonstrated the potential economic feasibility. Recovery of silver plays an important role in the economy of the process. This study presents promising values to further investigate this bioprocessing option.

Jan 1, 2014

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By Z. F. Hu

Tourmaline has the characteristics of piezoelectricity, thermoelectricity, spontaneous polarization and far-off infrared radiations. Ultra-fine powders of tourmaline have extensive applications in the fields of electron, chemical and environment protection, as well as health protection. The preparation technology of ultra-fine tourmaline powder is discussed. The key equipment of a pilot plant for producing ultra-fine tourmaline powder with jet mill and stirred ball mill is described. Using this pilot plant facility it is possible to produce tourmaline powder with particle size smaller than 100 nm, and a continuous production process can be realized. The final powder product has many superior performance such as high whiteness and large specific surface area, and it?s a negative ions emission can reach the value of 7190 ions per cubic centimeter.

Jan 1, 2014

By L. O. Filipov, N. E. Menad, A. Geneyton

"Zeta potential of synthetic monazites presenting various compositions were measured to investigate the effect of the main lanthanides substitutions on electrophoretic mobility and resulting IEP. The measurements are performed in a CO2 depleted and enriched solutions showing both reduced influence of monazite chemistry and strong influence of ions resulting from the solubilization and dissociation of CO2. The influence of oleic acid on the electrophoretic mobility of those monazites was also investigated. The influence of pH on oleate adsorption was studied using a bubble/particle adhesion system. Adhesion strength measurements were performed on pure synthetic monazite-(Ce) and monazite-(La). An extensive thermodynamic model of monazite in water was developed to highlight correlations between lanthanides hydroxides/carbonates species concentrations in the bulk solution and oleate adsorption. Based on electrophoretic measurements, advanced thermodynamic consideration and adhesion measurements, further details of the oleate adsorption model on monazite surface were proposed.INTRODUCTION Electrophoretic and potentiometric data on monazite and, a fortiori, other rare earth semi-soluble salts such as bastnaesite are extremely erratic (Chelgani et al. 2015). The isoelectric points measured with electrophoretic mobility methods range from 4.7 to 6.5 although sporadic data indicates an IEP (isoelectric point) far from that range. Different explanations are proposed in the literature to explain the IEP variability notably the numerous chemical substitutions that frequently occurred within monazite crystal lattice (Chelgani et al. 2015). Based on lanthanides speciation diagram, several authors highlighted the influence of specific lanthanide species on the flotation performance of rare earth semi-soluble salts when carboxylate or hydroxamate collectors are used. Although lanthanides ions have a great affinity for carbonates groups (Kragten et Decnop-Weever 1987), lanthanide (hydrogen) carbonates were not implemented in speciation diagrams. In this work, an advanced thermodynamic model is proposed to highlight correlation between flotation performance and lanthanide species predominance but also concentrations. Qualitative measurement of the monazite surface hydrophobicity are performed through tests of adhesion of coarse monazite particles onto bubbles. Since flotation and microflotation technics are highly influenced by hydrodynamic parameters, this method was investigated to obtain a sharp contrast between appropriate and inappropriate pH conditions. This paper is to investigate 1) the effect of lanthanides substitution on monazite surface properties through zeta potential measurements, 2) the mechanism of adsorption of carboxylates on monazite surfaces and 3) the effect of CO2 on monazite surface properties and carboxylates adsorption."

Jan 1, 2018

By L. A. Nemchinova, M. A. Arustamian

"For a long time tailings piles of mining and smelting complexes have met the eye being a prospecting feedstock source for many industries. Nowadays, 6.5 million tons of copper and cooper-zinc processing tailings are stockpiled in the Urals annually, as there is no technology of its processing to provide a full and complex metal extraction within mining and processing operations. In spite of large volumes of mining wastes, not more than 20% of annual overburden, approx. 10% of processing wastes, approx. 40% slags (1) are involved into processing.Based on today’s complex of economic, environmental and social challenges of ore processing, waste processing technology using existing capacities is a burning issue. Mining wastes characteristics (including fine dissemination, variability of physical and chemical properties of mineral surfaces under impact of oxidizing, leaching, etc.) predetermine challenges arising out of its involving into processing and justify high capital intensity of new construction or reconstruction projects followed by replacement of existing processing lines with new ones.In this paper, the authors propose flotation technology for mature tailings of copper, copper-zinc and polymetallic ore processing. The technology developed provides for upgrade of existing process flowsheet diagrams at minimum costs to produce additional saleable products including low-grade copper concentrate, saleable zinc concentrate and gold concentrate thus facilitates sustainable use of depleting minerals and operational efficiency due to cost-efficient processing of already mined materials, being in fact, final semi-products located near existing operations. This is particularly important for operations with standby capacities and not engaged workforce."

Jan 1, 2018

By Tamara Matveyeva, Tatiana Ivanova, Nadezhda Gromova

"The paper presents the results of study of the sorption and flotation properties of the reagents of plant origin - tannin and natural extracts of the oak bark and stems of plants, with a view to their application as a low-cost environmentally friendly modifiers of iron sulfide flotation for the recovery of minerals containing precious metals. The technique of preparation of plant extracts with a fixed content of extractable tannins has been developed.The mechanism of flotation reaction of tannin extracts has been identified as based on their adsorption on the surface of pyrrhotite and arsenopyrite to form strong complexes with iron (III) at concentrations below micelle concentration. It has been found that adsorption of plant extracts occurs without displacement of primarily adsorbed xanthate, and preliminary adsorption of xanthate did not preclude fixation of tannin on the mineral surface.It has been shown that plant extracts having hydrophilizing properties at low concentrations could be applied as selective depressants for pyrite, pyrrhotite and arsenopyrite in a weakly acidic, neutral or weakly alkaline medium. The use of plant modifiers could help to increase the quality of gold- and platinumcontaining concentrates and reduce the ecological impact on the environment."

Jan 1, 2014

By Bent Babel, Martin Rudolph

"The characterization of reagent-mineral interactions in flotation systems of finely intergrown ores holds difficult challenges for the applicability of standard techniques like Hallimond tube tests and contact angle experiments or renders them impossible due to a lack of sufficient samples in terms of quality and quantity. This disadvantage may not apply to more sophisticated techniques, but these often do not work in an aqueous environment. We present the utilization of an atomic force microscope with a hydrophobic colloidal probe to characterize the wettabilities of individual mineral domains of an ore sample, while additional spectral information is gathered by Raman spectroscopy. The exemplary ore sample investigated is mainly containing cassiterite and quartz, therefore the reference measurements like Hallimond tube tests and contact angle experiments were carried out with this binary system as a comparison. The focus of the study lies in the correlation of data gathered by the atomic force microscope and the Raman spectrometer with data from standard techniques. Finally, the applicability of the colloidal probe atomic force microcopy technique for reagent-mineral investigations is critically evaluated.INTRODUCTIONThe focus of this paper is the application of colloidal probe atomic force microscopy (CP-AFM) for theinvestigation of reagent-mineral interactions on a binary system of cassiterite and quartz. This and similar concepts using hydrophobic AFM probes have been applied by multiple authors (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b; Wada et al., 2017; Xie et al., 2017). The hydrophobic interaction is the main interacting mechanism for the hydrophobic colloidal probe with hydrophobic sample surfaces and the long range attractive component has been accounted to nanobubbles on the interacting surfaces (Yakubov et al., 2000). More detailed information on nanobubbles are available in two reviews compiled by Attard and Hampton (Attard, 2003; Hampton and Nguyen, 2010). This paper is based on the work by Rudolph and Peuker comparing different AFM based measuring concepts, additionally gathering data with Raman spectroscopy and correlating results of microflotation and CPAFM measurements (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b)."

Jan 1, 2018

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By Masanori Mori, Hajime Miki, Osamu Ichikawa, Tsuyoshi Hirajima, Mitsuru Sawada, Keiko Sasaki

For pretreatment of selective flotation, surface oxidation of chalcopyrite and molybdenite was applied by oxygen plasma then the minerals were washed by solution at pH 9 with oxygen bubbling. Surface characteristics of these minerals were investigated with AFM, XPS, zeta potential and contact angle measurements. Contact angle of chalcopyrite and molybdenite decreased a lot by plasma treatment. When they were washed with pH 9 solution with oxygen bubbling, contact angle of molybdenite increased whereas chalcopyrite one kept low. Adhesion force measurements indicated similar behavior. Result of flotation experiments indicated low recovery of both chalcopyrite and molybdenite after plasma treatment and only molybdenite recovery became higher after washing. Selective flotation of chalcopyrite and molybdenite could be achieved with this process. Possible mechanism of selective flotation was proposed from the results of XPS, AFM, etc.

Jan 1, 2014

By Diego Mesa, Willy Kracht

Frothers may be classified as weak or strong depending on their ability to produce stable froths, which is related to the amount of water that they transfer from the pulp to the froth. They can also have an effect on the non-selective mechanism of recovery by entrainment, implying that both selectivity and froth stability are, at least to some extent, frother dependent. Solids, on the other hand, also have an effect on froth behaviour. Clays, which are characterized by their small particle size, laminar shape, and high specific surface, tend to report to the froth phase and have an enormous impact on both froth stability and the overall performance of the flotation process. The purpose of this work is to shed light on the effect that different frothers have on the froth behaviour when clays are present. In order to do that, two sets of experiments were conducted using frothers from the families of alcohols and polyglycols. For each test, the equilibrium froth height was measured at different frother concentrations in an agitated machine with an acrylic square-base cell that was 11 cm wide and 25 cm high. The cell was designed in such a way that froth was able to grow without concentrate discharge. In the first set of tests, pure clays such as kaolinite and montmorillonite were used. In the second set, an actual copper sulphide ore with a high content of clays was used as solid phase. The results, expressed as curves of equilibrium froth height against frother dosage, showed a coupled effect of frother-clay on froth behaviour for both sets of experiments. In some cases, the froth grew up until the border of the cell with only a few parts per million of frother. In other cases, the equilibrium froth height varied smoothly with frother dosage. The results suggest that choosing the right frother can be of use for controlling the froth behaviour when dealing with clay-rich froths, using frother dosage as the control variable. The application of these findings at industrial scale are discussed and some recommendations are given.

Jan 1, 2018

By U. M. J. Boin, W. L. Dalmijn, T. P. R. de Jong

"This paper explores the complex interrelationship between the resource cycle, recycling and metal production as a function of economics, environmental legislation, and product design. It is argued that central to optimising this resource cycle lies the control in particular of physical separation plants by the application of advanced sensor technology and sorting equipment, as well as suitable control and sampling algorithms supported by optimising mass balance models.Metals are produced through a long chain of processes. For primary resources, metals production goes through mining, mineral processing, ore smelting, conversion and refining steps or via low temperature hydrometallurgical processes, or a combination of both pyro- and hydrometallurgical operations. For the recycling of resources, metals are separated and recovered from metal scrap, which plays an increasingly important role in the world. Metals after being produced, either from primary or recycling resources, have to be further refined or manufactured into various types of alloys and finally shaped into different products for the end-users. Since the end-user discards products the contained materials find their way back into the resource cycle as scrap. Therefore, controlling the metallurgical reactors also controls, in a much broader sense, the material quality in the complete metals cycle, from the production phase, to the end-use phase, up to the recycling phase (Reuter et al., 2003). The recycling phase includes separation of materials into saleable intermediate products, which are reintroduced into the production phase as a recycling resource. Therefore, the metallurgical processes in each unit operation in the metals production and processing chain have to be controlled, so as to achieve optimal performance of high product quality, low energy and materials consumption, and low environmental impact."

Jan 1, 2003

By Tingting Li, Guodong Li, Dezhou Wei, Cong Han, Shuling Gao, Yanbai Shen

"The aim of this study is to solve the problem of tungsten leaching from scheelite concentrate using sodium hydroxide in the presence of phosphate by an autoclaving process, which is one of main development techniques for tungsten recovery. To understand the applicability and leaching performance of tungsten leaching from scheelite concentrate, the main work is to investigate the effects of leaching parameters such as initial concentrations of NaOH and Na3PO4, reaction temperature, stirring speed, liquid-to-solid ratio and reaction time on WO3 dissolution rate to obtain the optimal leaching conditions. The chemical composition and phase composition of the samples were evaluated by means of XRF and XRD. The content of WO3 in the leaching residue obtained via washing, filtering and drying was analyzed by thiocyanate spectrometric method. The optimal leaching conditions were found to be NaOH concentration of 6.76 mol·L-1, Na3PO4 concentration of 1.35 mol·L-1, reaction temperature of 180°C, stirring speed of 400 rpm, liquid-to-solid ratio of 2.0 and reaction time of 90 min. The results showed that tungsten leaching rate of 99.20% was reached under the optimal conditions. The technology exhibited superior leaching performance, which not only reduced the consumption of sodium hydroxide but also greatly decreased reaction time in comparison to a conventional autoclaving process. INTRODUCTION Tungsten is an important strategic metal, which is widely utilized in a variety of industries due to its high melting point, superior mechanical properties and heat-resistant performance [1-3]. The chief raw materials for the production of tungsten in nature are wolframite and scheelite [4, 5]. Among them, approximately two-thirds of the tungsten reserves contain scheelite deposits in the world [6, 7]. With the progressive exhaustion of high-quality wolframite resources, scheelite has become a predominant primary resource for the production of tungsten [8, 9]."

Jan 1, 2018

By Regis Texeira, Leopoldo Gutierrez, Vicente Hernandez, Caludia Vidal, Lina Uribe

"Molybdenum is currently the most important by-product of Chile´s copper mining industry. This mineral has gained international relevance over the years, because of its price. At mining deposits in Chile, copper and molybdenum are extracted together and then separated in a concentration process consisting of several flotation steps using sodium hydrosulfide (NaHS) as copper depressant. However, there are environmental issues related to the potential emisions of toxic hydrosulfide gas and bad odours, which affects nearby communities and suppose a risk for operators. This problem has led to the need for development of new technologies to eliminate the use of NaHS in the process of selective flotation of Cu and Mo minerals. In this work, results of flotation tests in which lignin derivatives reagents are used to obtain the selective separation of Cu and Mo minerals by flotation are presented. In this technology molybdenite is depressed by the action of lignin derivatives (lignosulfonates), while copper sulfides remain hydrophobic and float. The use of lignin derivatives in the selective flotation of copper molybdenum minerals represents a non-toxic alternative to NaHS.INTRODUCTIONSeparation of copper sulfides from molybdenite is commonly achieved through a two-stage flotation process. In the first stage the collective flotation of copper sulfides and molybdenite is promoted to generate a collective concentrate which is then treated in a second stage with sodium hydrosulfide (2.5-3.0 kg/t NaSH) to depress copper sulfides flotation without affecting the flotation of molybdenite. As a result a copper concentrate with 30-35% Cu, and a molybdenum concentrate with 50-52% Mo are generated. Although this process is widely used at industrial level, environmental issues related to the risk of H2S generation and bad odors have always been a concern. Thus there is a need in the industry for a more environmentally friendly process to separate copper sulfides and molybdenite."

Jan 1, 2018

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

By K. Trybalski

Facing the optimization activities, which purpose is to minimize the copper processing costs, the main sources of their occurring were presented. In this purpose, the costs analysis was performed, divided to individual standings, for one of the polish copper beneficiation plants. It was proved, that the main component of the copper beneficiation costs is energy consumption, generated mainly in grinding and classification node, particularly by operating mills. The technological system ? grinding and classification node ? in KGHM Polska Miedz S.A., ZWR region Lubin was then selected to investigation. To evaluate the grinding and classification node, the energetic factors W were proposed, calculated on the basis of the energetic-technological data of process, given by node monitoring system. The correctness of the energetic factors selection to evaluate the work of this node and their practical application in industrial conditions was experimentally proved in other technological object. The selected technological object ? grinding and classification node ? was then mathematically modeled and optimized. The calculated energetic factors were the basis to build mathematical models, identifying industrial copper grinding and classification process. The models described correlation and character of dependency between factors and energetic-technical data of the process. These were regressive and neural networks models. On the basis of factors models, the optimization tasks were determined, which purpose was to select the optimal points of grinding and classification node work. Also, the estimated economical effect, possible to achieve after introduction of given monitoring values to grinding and classification node optimization system, was presented.

Jan 1, 2014

By B. Y. M. Bueno

Biosorption of heavy metals can be an effective process for the removal of heavy metals ions from aqueous solutions. In this study, the adsorption properties of Rhodococcus opacus biomass for Pb(II) and Cu(II) ions was investigated. The effects of initial pH, initial metal concentration and biomass concentration on biosorption efficiency were studied in a batch system. Results showed that the initial pH would play an important role in the Pb(II) and Cu(II) ions removal by R. opacus and affected the zeta potential of R. opacus. The equilibrium adsorption was reached with 60 min. The Langmuir and Freundlich models were used for describing of adsorption isotherm data. The maxi-mum adsorption capacities of biomass were determined as 94.3mgg-1 and 32.2 mgg-1 for the Pb(II) and Cu(II) ions, respectively. The experimental data fitted to pseudo second order kinetic model. Adsorption capacity of Pb(II) ions was found to be reduced by the presence of the other competing metal ions in the system. The FT-IR results of R. opacus biomass showed that biomass has different functional groups and these groups are able to react with metal ions in aqueous solution.

Jan 1, 2014