Search Documents

By Mauricio Guimarães Bergerman

At the regrind or secondary grinding stages of base metal ores, the concern about energy efficiency is usually extremely important. In general, the specific energy consumption at this stage is higher than during the primary grinding stages. In addition, a tendency of finer grinding has been observed in the new projects of metallic minerals, due to the finer mineral liberation, which leads to increasing capital and operational costs. At Vale?s new copper projects in Brazil, regrind sizes with a P80 of approximately 40 to 20 µm have been necessary. Conventional ball mills, adequate for primary grinding, usually bring about low energy efficiency with products bellow 50 µm. Vale is using the vertical mill on its copper projects ? Sossego and Salobo, in order to optimize the regrind of rougher concentrates and reduce energy consumption. This paper presents the results of industrial surveys carried out on the Vertical mill circuits of Sossego plant during its initial years of operation, and compares these results with the design criteria and laboratory regrind tests used for the mill scale up. Keywords: grinding, regrinding, copper, vertical mill, stirred mill

Sep 1, 2012

By Y. De Gao, C. Gang Zhong, X. Yang Qiu, Li Wan

The chelating reagents are used as effective collectors in wolframite flotation, and certain metal cations need to be added using chelating collectors so as to activate valuable minerals and obtain good flotation indexes. Different metal cations will result in different reactivity with collectors, in order to select the effective activator in BHA flotation of wolframite, the activation effectiveness of different metal cations on wolframite ((Fe,Mn)WO4) flotation were studied using pure minerals. The results showed that the wolframite activation by Pb2+was the best among the selected cations. The maximum flotation recovery of wolframite was found to be 95.58 % under conditions of 100mg/LBHA and 1×10-4mol/L of Pb2+at pH 9. The dosage of Pb2+needs to be controlled in an optimum range. Also, the activation mechanism of Pb2+ on BHA flotation of wolframite was investigated by measurements of contact angle, zeta potential, adsorption capacity and IR spectroscopy. It was found that Pb2+ could chemically adsorb onto the wolframite surface improving the flotability of wolframite and enhancing the adsorption of BHA on wolframite. When the dosages of BHA and Pb2+ were 100 mg/L and 1×10-4 mol/L, the adsorption quantity of BHA on wolframite sharply increased up to 0.30 mg/L at pH 9 compared with wolframite treated with only BHA.

Jan 1, 2014

By G. Jenny

The particle size distribution of ground minerals is of decisive importance for downstream processes like floatation, separation, drying or others. In order to optimize the process efficiency on one hand and the final product quality on the other hand an early control of the grinding or classification stage is essential. The ultrasound based particle size analyser OPUS is capable of performing on-line particle size distribution (PSD) and solid content measurement of mineral slurries such as iron ore, copper ore, fluorspar, or quartz sand and alumina directly in heavy and rough process environment. The instrument provides a PSD of 31 size classes and can be applied for particles from nanometer range up to several millimetres. Arbitrary interpolations in between the 31 measured points are available. Typical residue values show an excellent agreement to off-line particle size analysis methods such as e.g. sieve analyses or laser diffraction. OPUS is designed as rugged in-line probe made from stainless steel. The applied technique is independent of product flow dynamics, contamination, optical properties, vibrations, pressures or changes in solid concentrations. The instrument provides all data on the system?s PC or on the process control system by a variety of interfaces.

Jan 1, 2014

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

By A. R. Hasankhoei

Water recycling is of prime importance in mineral processing due to consumption of large amount of water. This issue is vital in areas with a low rainfall such as Shahre-Babak (Kerman, Iran). Deep cone thickeners, unlike conventional thickeners, have a low diameter to height ratio where large amounts of flocculants are used to increase particles settling rates. The high bed heights (over 10 m) produce enough pressure to create a paste type underflow indicating maximum water recovery. Flocculent preparation, conditioning, and distribution along with the bed height are among the important factors affecting the performance. Four deep cones are used to recover water from the tailings of the plant. Plant data indicated that the thickener never reached the target underflow percent solids (63%) and the average underflow concentrations were between 49 and 57%. By modification and optimization of flocculent preparation and distribution methods the underflow percent solids increased by 3-4%. This translated to an increase of water recovery from 67 to 73%. This was equivalent of 53000 m3 saving in monthly water consumption. Keywords: deep cone thickener, water recovery, flocculant, copper tailings

Sep 1, 2012

By Robin B. Batterham

"Since the 1970?s we have seen a marked corporate response in terms of the environment. In part this has come from regulation but it has largely come from stakeholders and the community. Rising expectations have in general been met. We now see a similar trend towards sustainability. At the same time, the importance of mining to the share market has decreased drastically and with that decrease has come the requirement for the mining sector to show returns similar in manner to other sectors. While rationalisation can achieve some progress towards these goals, the long-term requirement is for innovation, as it always has been. This paper looks to the logical goal of innovation within a sustainable mining framework and targets the removal of the desired metal values with minimal environmental footprint. It is suggested that broad ranging alliances will be necessary, particularly amongst the R&D suppliers, to achieve this goal. Industry will need to take an active role given the recent global restructuring.THE MARCH TO SUSTAINABILITYSince the 1970?s there has been an increasing corporate response on environmental matters. We have moved from matters environmental being issues relevant only to minority groups through a series of attitudinal changes by management. Whilst there have always been examples of excellent environmental performance, for many in the 70?s spending money on improving the environment beyond some minimal level was seen as a distraction from production or treated in a similar way to donations to the community. There is little of that attitude these days, as most mining companies have long since regarded the environment as a core business direction. Indeed, for some years one could note an escalation in matters of environmental reporting to the extent that the environmental performance of companies is now very public. In some cases, NGOs have even been invited to help certify and audit the reporting standards. Similarly with health & safety.There is now a rising expectation on the part of the community that social matters will also be given the same level of support as health, safety and the environment. This time around it would appear that the mining industry is at the leading edge of sustainability. The Global Mining Initiative (Global Mining, 2002) and the contributions to the Rio World Summit on Sustainable Development (Rio +10, 2002) suggest that sustainability is being taken very seriously by the mining industry. For sustainability it is convenient to use the Brundtland (1987) definition. This definition has widespread acceptance with governments, industry, environmental groups, financial institutions and individuals as a direction against which our activities and plans can be measured."

Jan 1, 2003

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By D. Moradkhani

The heap leaching of oxide copper ores with copper cathode recovery by solvent extraction and electrowinning is now well established as a low-cost method of copper recovery. The main purpose of this study was to extract copper from the copper low-grade oxide ore of Chodarchaei mine using column leaching. The copper oxide ore contained 1.1% Cu and 1.75% Fe. The mineralogical analysis indicated the malachite (Cu2(OH)2CO3) was mainly composed of oxidized phases. The sulfuric acid leaching experiments were performed under the laboratory conditions. The influence of several parameters on the course of the reaction such as particle size, acid concentration, flow rate, and time was examined. The optimum collective extraction of copper and iron was obtained at a particle size of +10-15 mm for a leaching duration of 3 days with sulfuric acid concentration of 100 gpl and using a flow rate of 2.5 cc/min. Under these conditions, the recovery of copper and iron were 98.54% and 41.99%, respectively. Keywords: column leaching, copper, iron, working diagram.

Sep 1, 2012

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By Susanna G. de Jager, Francis W. Petersen

"The aim of the project was to develop a methodology applicable to different South African coal types to be able to predict with a high degree of certainty what kind of reagent will be suitable for flotation of a certain coal type.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements.The flotation tests showed that the best reagents to float all of the coal samples studied are iso-decanol and dodecene. These reagents produced flotation products that are near to the release curve. Statistical relationship for predicting ash content and yield that can be expected for a certain coal type and selected collector was obtained. From the relationship, the accuracy of the yield is above 95% (p-value below 0.05) with a linear regression of 0.9289. The accuracy of the ash is slightly lower with a linear regression of 0.7841 but also above 95%."

Jan 1, 2003

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By F. C. Araújo, T. Tavares, J. Leite

"This work presents the small-scale mining cluster of kaolin in Rio Grande do Norte (RN) and Paraiba (PB), both Brazilian states, including the following information: number of companies, process flowcharts, production numbers, mineralogical (XRD) and chemical (XRF) composition, granulometric distribution (screen and laser granulometer) and image analysis (SEM). Some social indicators in the region of the RN and PB States are presented in association with these data. The number of companies and their flowsheet were obtained through in situ visits and sample collection for technological characterization. The comparative study of the different flowsheets for kaolin production in the world was done using the databases and presenting the state of the art of kaolin processing. The results indicated that the mean feed typically contains 35-39% kaolin with quartz, muscovite and kaolinite as main mineralogical components and SiO2 (65.83%), Al2O3 (21.19%), K2O (3.9%), and Fe2O3 (0,63%) as main chemical constituents. The products of mineral processing are twofold, one between 74 µm and 37 µm, and the other smaller than 37 µm. The wastes of operation had major quantities of kaolin. The average Human Development Index (HDI) of the cluster region is approximately of 0.61, which shows an association between mineral processing plant and social indicators. The kaolin recovery, however, is between 30-55% for the three most common types of flowsheets that are currently used in the small kaolin mining cluster, indicating a need for technological improvement to achieve regional development. These data could be used incrementally to adapt the process plant currently used in the small-scale mining cluster of kaolin."

Jan 1, 2014

By V. Tsyplakov

This article reviews factors of preg-robbing effect, occurring in the course of pressure oxidation of ore and concentrates, containing chloride compounds and so-called 'organic carbon'. The article also summarizes the main results of the studies and testwork conducted to overcome this effect. The following efficient preg-robbing mitigation methods have been noted: higher temperature of pressure oxidation process, preliminary removal of natural carbonaceous material from concentrate, chloride removal prior to concentrate pressure oxidation, and addition of water-soluble organic blanking agents, which suppress the adsorption activity of the native ore adsorbents. Keywords: preg-robbing, double-refractory gold concentrates, pyrite, arsenopyrite, blanking agents, pressure oxidation, autoclave leaching

Sep 1, 2012

By G. V. Sedelnikova

Biohydrometallurgical studies were performed on the sulfide gold-arsenic concentrate obtained in treatment of refractory ore from a deposit located in northern Russia. Gold is disseminated in sulfides-arsenopyrite, pyrite and antimonite (their content is 10.0%, 30.4% and 0.7%, respectively). Gold extraction is only 11.8% by cyanidation. Results are given for test bacterial oxidation of the concentrate in continuous mode at temp. = 28~32°C using mesophilic bacteria and at temp. = 32~38°C using the association including moderate thermophilic bacteria. The paper shows that the use of moderate thermophilic bacteria allows to speed up sulfide biooxidation and reduce its time to 96 hours compared to leaching at temp. = 28~32°C for 110~120 hours. The optimal range of pH = 1.5~2.0 of biooxidation process was determined where bacterial solutions are produced with the molar ratio Fe:As > 3 necessary for precipitation of hard-to-solve, environmentally safe arsenical precipitates. Electron microscopy showed that sulfide biooxidation results in liberation of disseminated gold with nanoparticle-level sizes. High sorptive activity of carbonaceous matter and other compounds of bacterial residues cause low gold extraction into cyanide solution ? 28.7%. 10% resin load makes it possible to extract 88.1% Au. Aeration of pulp in calcareous medium enhances extraction to 95.7% and decreases cyanide consumption from 17kg/t to 8 kg/t.

Jan 1, 2014

By Wantae Kim, Hoon Lee, Kwanho Kim, Sangbae Kim

Mechanochemical activation of starting minerals and their effect on the solid-phase synthesis and properties of ceramics with lower thermal expansion coefficient was examined. The mineral mixture, pyrophyllite-gibbsite-lithium carbonate, was prepared for the synthesis of ?-eucryptite (Li2O•Al2O3•2SiO2). Dry grinding using a planetary ball mill promoted the amorphization of the starting mixtures. XRD and FT-IR results showed that the crystallization of the target materials occurred from the ground mixtures by calcination. The crystallization of them increased with increment of grinding time and calcination temperature. In the synthesis, the trace of undesired phases such as quartz and cristobalite once formed during calcination at the temperature range from 750 to 850 °C almost disappeared and monophase ?-eucryptite was formed in the ground mixture at 950 °C. The lowest liner thermal expansion coefficient (TEC) of ?-eucryptite prepared was -2.5x10-6•°C-1. The thermal expansion behavior characteristics of the calcined

Jan 1, 2014

By P. Spolaore

In the frame of Bioshale FP6 project, the bioprocessing of a polymetallic and polymineral concentrate produced in an industrial operation in Lubin, Poland, was assessed. Following successful batch culture tests, processing in continuous conditions was tested to determine the main specifications for the application of the stirred-tank technology to this sulphide concentrate from black shale ores. The experimental work was carried out in a laboratory-scale unit consisting of 3 stirred tanks (50L or 20L) using an acidophilic and moderate thermophilic bacterial population. Different configurations of the unit and key operating parameters were tested (nutrient medium composition, solids concentration, rates of agitation and aeration). Scientific and technical approaches, such as bacterial community structure and mineralogical analysis were implemented in order to better understand the chemical and biochemical reactions occurring in the system. Using the data produced during the continuous operation, downstream processing assessment for both copper and silver recovery was also carried out. The best copper recovery obtained in the continuous operation was 92% and a hot brine leaching of the bioleach residue (PLINT process) allowed to recover 92% of the silver. A preliminary tech-no-economic evaluation of Lubin concentrate bioprocessing including bioleaching, copper and silver recoveries demonstrated the potential economic feasibility. Recovery of silver plays an important role in the economy of the process. This study presents promising values to further investigate this bioprocessing option.

Jan 1, 2014

By J. Y. Tian

In view of the fact that many domestic iron ore-dressing plant applying flotation cells in the re-verse flotation, to improve the technical level of magnetite reverse flotation, we apply such a technological process of one stage rougher and two stages scavenger flotation column respectively. The middling from the two stage scavenger process are returned to magnetic separation for condensing. By contrast, the technological process of one stage rougher and one stage cleaning flotation cells is made up of by multi-magnetic separation and magnetic middling regrinding separations. It has been proved that the flotation column we offer can simplify the technological process structure, obtain advanced technical indexes, run the system smoothly, reduce energy consumption, and be environ-mental friendly.

Jan 1, 2014

By N. Pradhan

In the Sukinda valley, Orissa, India, a large quantity of overburden material is generated during the mining of chromite mineral (on average 10 tons for every ton of ore). The overburden hereby depicted as ?lateritic nickel ore? contains on an average 0.5% Ni. IMMT Bhubaneswar is working on this material for extraction of nickel and cobalt. But for better recovery of metal values, thermal activation or thermal reduction of ore is required. An alternative biotechnological route for reduction of ore is hereby attempted. An anaerobic dissimilatory Iron (III) reducing bacterial consortium (here denoted as IRB), capable of imparting iron phase changes in the lateritic nickel ore was established which improves the subsequent extraction of co-precipitated Co (III) and Ni (II) from the ore. In this study, properties of thermally and microbially reduced lateritic nickel ore are compared vis-à-vis original ore. Due to the phase changes, original light brown color of the lateritic nickel ore changes to dark brown on IRB treatment. This dissimilatory reduction of ore leads to formation of some magnetic particles, which were separable by hand held magnet. Roasting and IRB treated ore on acid leaching with H2SO4 show about 45 % and 36 % leaching of nickel ore compared to about 18 % leaching from the original lateritic ore. If bacterial reduction method is successful, cost intensive method of ore roasting process can be eliminated. Thus, it is possible to make use of dissimilatory iron reducing bacteria for recovery of valuable metals from off grade iron ore/ laterites. Keywords: lateritic nickel ore, bacterial reduction, thermal reduction, dissimilatory fe (iii) reducing bacteria

Sep 1, 2012