Search Documents

By K. D’Elia, L. D. Ogrel, O. A. Malyshev, T. I. Yushina, I. M. Petrov

"The purpose of this research is to develop enhancements in the mineral processing by flotation methods of nonferrous ores. Currently, 180-190 million tons of ore are processed by flotation in Russia. The annual processing volume of copper-nickel and copper-zinc ores exceeds 20 million tons. In the total volume of processed ores by flotation, non-ferrous ores account for roughly 35% and ores of precious metals for another 15%. The total demand of flotation reagents in Russia in 2016 was estimated at 170,000 tons. Sulfur-based collectors used in the flotation of non-ferrous sulfide ores (typically, xanthates) do not always offer sufficiently high recovery of valuable components.It has been found that reagents like DMIPEC and DK-80 improve the recovery of metals into concentrates. To identify the reasons of that higher recovery, quantum chemical calculations of the mechanism and interaction forces of DMIPEC with non-ferrous sulfides were undertaken by determining the stabilization energy of the resulting chemical complexes. It has been shown that, in the interaction of DMIPEC and DK-80 with the surfaces of sulfide minerals, ethylene and acetylene bonds act as the reaction centers, and the formation of molecular p-complexes is the result of metal-cation interactions with the surface and the flotation reagents.In the flotation of non-ferrous ores, DMIPEC and DK-80 act as selective supplementary collectors with foaming properties, and at a flow rate of 3-35 g/ton, they reduce the flotation time, and increase copper recovery by up to 3.5%, zinc recovery by up to 12%, gold recovery by up to 8-10%, allowing to increase the recovery of valuable components by 1.5-12.0%, basically this kind of reagents nearly double the flotation rate, improve the grade of the concentrate, improve the stability of the flotation process parameters, and reduce the environmental impact of flotation plants."

Jan 1, 2018

By William Skinner, Jennifer MacCarthy, Jonas Addai-Mensah, Ataollah Nosrati

"Acid leaching in agitated tanks is central to hydrometallurgical processing for valuable metals’ (e.g., copper, gold, nickel and cobalt) recovery from low grade (e.g., < 2 wt.%) ores. In this study, atmospheric leaching behaviour of Australian saprolitic nickel (Ni) laterite ore using sulfuric acid was investigated under isothermal, batch conditions at pH 1. The effect of primary process variables comprising time (4 h) and temperature (70 and 95 oC) on the leaching mechanisms and kinetics was established for -2 mm, low grade (~1 % Ni) saprolitic ore dispersions at 40 wt.% solid loading. Leaching proceeded incongruently, reflecting the proliferation of gangue minerals’ constituent elements (e.g., Mg, Al, Fe) alongside Ni and Co in the pregnant leach solutions (PLS). Subsequent analysis showed that 89% Ni and 78% Co were extracted after 4 h at 95 oC whilst at 70 oC the recoveries of these metals were markedly low (< 25 %). Overall, 177 and 644 kg H2SO4 /t dry ore were consumed at 70 and 95 oC, respectively. Activation energy of 79.0 ±1.0 kJ/mol was estimated for the mechanism of Ni and Co leaching and associated kinetics. Particles size analyses indicated that when the breakage of frail laterite particles due to shear is taken into consideration, differences in feed and leached product particle size distributions were insignificant , despite a remarkable increase in BET specific surface area of the product. Mineralogical analyses of the feed ore and leached solid products revealed a sub-crystalline silica phase enrichment of the latter. The overall results suggest that the mechanism of acid leaching of saprolitic Ni laterite may be described by a chemical reaction-controlled, shrinking core model."

Jan 1, 2014

By L. S. Zhou

Germany-made AFX-100 multi-grade fluidized classifier, with exquisite built-in structure and unique novel design, materializes not only advanced and efficient classification, but also precise particle distribution and safe operation, in addition to lower energy consumption and operational cost. It, simultaneously in place of screw grader, water cyclone, and fine mesh sieve, is equipped with multi-function, and indicates superior advantage in comparison with other else grading facilities. As the third-generation equipment, which is efficient and modern, it, in China and therefore all over the world, will find wide application in processing both fine and ultra-fine iron ore resources. Industrial test, carried out in Benxi Steel?s Waitoushan Iron Mine, shows efficient classification, i.e., ?74µm particle contents in coarse, medium and fine products come to 6.09%,11.82% and 82.73%, respectively, while qualitative and quantitative efficiencies end up by 74.38% and 87.66%, respectively. Its separation efficiencies amount to 2.2 times as many as spiral classifiers, 1.8 times as hydrocyclones, and 1.3 times as vibration high-frequency fine screens. Another industrial test, which was practiced in Anshan Steel?s Donganshan Sinter Plant, indicates that classification qualitative efficiency comes to 65.06%, equal to 1.51 times as many as hydrocyclones; yield, 55.79%; -71µm particle contents in medium and coarse products, 42.02%; -71µm content in fine product, 95.42%; and concentration, 12.33%. Estimated separation indexes are as follows: Yield for concentrate at 31.22%, up 0.22% than that from general processing line; concentrate grade at 66.42%, up 1.13%; recovery ratio comes to 65.84%, up 1.28%, which, based on pilot study, results in 20 million yuan of economic return for Donganshan Floatation Plant.

Jan 1, 2014

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By O. Guven, I. Karaagaçlioglu, O. Ozdemir, M. Çelik

In this study, the effect of morphological properties such as shape factors and roughness of the glass beads on their flotation efficiency were determined using image analysis and profilometer methods. There is a considerable correlation between the shape factors, surface roughness and flotation behavior of the glass sample. These results indicate that as the particle shape is away from roundness and smoothness, it acquires more hydrophobicity.

Jan 1, 2014

By X. Y. Liu

A culture-independent approach based on 16S rRNA gene clone library was used to analyze the bacterial community change both associated to the solids and in the liquid phase during pyrite bioleaching process. Phylogenetic analyses of 16S rRNA fragments revealed that the retrieved se-quences mainly related to genus Leptospirillum, genus Sulfobacillus and genus Acidithiobacillus. During the bioleaching process, genus Leptospirillum trends to grow associated to the solids while major of genus Sulfobacillus were in the liquid fase, only accounting little portion in the solids. Genus Acidithiobacillus can grow both on the solids and in the liquid phase, but accounting high portion on the solids.

Jan 1, 2014

By Sergio Castro, Janusz Laskowski

In the flotation in highly concentrated electrolyte solutions not only ionic strength but also chemical composition, flotation pH and mineral properties play an important role. As a result an improvement or depression may be observed. A strong improvement in the floatability of hydrophobic bituminous coals and other inherently hydrophobic minerals is characteristic for the "salt flotation process", which is carried out in concentrated electrolyte solutions at natural pH and without addition of any flotation reagents. However, pH is a key factor when saline and hipersaline waters with hydrolyzing metallic ions are used as process water. In the case of flotation of Cu-Mo sulfide ores in seawater, molybdenite is strongly depressed by the Mg2+ hydrolysis products when pH is raised to depress pyrite. Process water with a high content of Mg2+ and Ca2+ ions, and this also includes seawater, have deleterious effect on the anionic flotation of industrial minerals with fatty acids. The flotation of potash ores is carried out in NaCl-KCl saturated brine (6-7 mole/L of NaCl and KCl) with the use of long-chain amines. Such a high electrolyte concentration changes dramatically the amine Krafft point making the collector insoluble in brine; its mode of action entirely differs from that in conventional flotation processes.

Jan 1, 2014

By Harri J. Lehto, Marja I. Oja

Empirical models used for predicting the performance of screens on the basis of capacity, cut size, water split and grade efficiency curves were evaluated. This paper reports experimental results obtained with single-deck Derrick screens. The performance of the screen was tested with limestone in a separate screen set-up, in a pilot plant and in industrial scale test runs. The results of pilot plant experiments showed that the measured water split was higher than the measured bypass. This is an indication to that water flow does not entrain the same proportion of all fine particles present in the feed which is advantageous for screening. The experimental design for the industrial test runs was made on the basis of the pilot plant tests. Suitability of the existing models has been checked and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model. An empirical model for the evaluation of the model parameters as a function of pulp density of the feed and the load of the screen is suggested.

Jan 1, 2003

By Ping Fang, Dezhou Wei, Zichuan Guan, Wengang Liu, Yanbai Shen

A new cationic collector, bis(2-hydroxy-3-chloropropyl) dodecylamine (N23), that can be dissolved in water easily was synthesized successfully. Its flotation performance to quartz was investigated compared with dodecyl amine in hematite reverse flotation system. It was found that N23 showed stronger collecting performance to quartz than dodecyl amine. The maximum recovery of 98% to quartz was obtained at a collector concentration of 43.3 mg/L in the pulp pH range of 6-9. This collector can be used to float quartz from hematite when starch was used as depressant. Optimal separating results with 90.06% iron recovery and 66.3% iron grade to artificially mixed sample were achieved at a collector concentration of 43.3 mg/L and a starch concentration of 23.3 mg/L at neutral pulp pH when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by infrared spectroscopic analysis and zetapotential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occurred between the collector and quartz surface.

Jan 1, 2014

By T. Damyanov

Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. A modelling simulation study of the behavior of two grinding media in the grinding process was conducted to determine the possible advantages of the new shape milling bodies called tetraballpebs. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. A three dimensional CAD model of the mill drum with a diameter of 1200 mm was used. A continuous operating mode was simulated in terms of the 3D contact elements of the model (milling bodies and mill drum). Simulation tests were carried out in a typical grinding mode and at a typical rotational speed of the drum mill (75 per cent of the critical speed in cataracting mode). Studies carried out with both grinding media include equal number of milling bodies with the same weight and volume. Having thus ensured a uniform mass of the grinding media and same number of milling bodies, and constant other conditions and process parameters, conclusions can be drawn about the influence of the shape of the milling bodies on the grinding process. A kinematic analysis of the system using CAE (computer-aided engineering) model parameterization was conducted. The controlled parameters are: ? Power draw; ? Kinetic energy of each milling body; ? Motion of milling bodies inside the drum Keywords: grinding, grinding simulation, balls, tetraballpebs, DEM, CAD-CAE

Sep 1, 2012

By A. M. Ozbayoglu

Gross calorific value (GCV) of coals was estimated using artificial neural networks, linear and non-linear regression techniques. Proximate and ultimate analysis results were collected for 187 different coal samples. Different input data sets were compared, such as both proximate and ultimate analysis data, and only proximate analysis data and only ultimate analysis data. It was observed that the best results were obtained when both proximate analysis and ultimate analysis results were used for estimating the gross calorific value. When the performance of artificial neural networks and regression analysis techniques were compared, it was observed that both artificial neural networks and regression techniques were promisingly accurate in estimating gross calorific values. In general, most of the models estimated the gross calorific value within ±3% of the expected value.

Sep 1, 2012

By Shi Shuaixing Zhang Yuejun, Fan Xuesai Zhangming

"For the traditional principle of flotation cell design, or in the perspective of some researchers, the mixing effect of impeller for flotation cell is not only to suspend the particles off the bottom, but also to mix slurry well to achieve a uniform system. But for some special processing conditions, the depth profile of slurry concentration and particle size demonstrates an obvious difference. In the part around of the impeller in the cell, the slurry concentration is much higher than the part below the lip.For the vanadium titano-magnetite flotation process, distinguished with high concentration and large coarse particle size fraction, even though the concentration is very high, it can reach good gas dispersion, which is a fundamental principle for flotation cell design and application. The gas dispersion is not a challenge in the high slurry concentration environment, not only in the vertical direction, but in the cross section. Different levels (the distance from the lip is 400mm, 700mm, 1200mm, 1700mm, 2200mm, 2700mm) slurry in the flotation cell is sampled and analyzed. The slurry concentration of the 3 levels(1700mm, 2200mm, 2700mm) is about 55%, but the slurry concentration decreases from 55% to 25% sharply towards the lip.Therefore, a new understanding and viewpoint is presented, that the uniform system of slurry is not always reasonable for all of the flotation process. For some special process, if the coarse particles are needed to agitated well and transported to the upper cell, the quiescent zone in the upper cell will be destroyed and enhance the detachment probability for the coarse particles. The difference of slurry concentration and particle size fraction benefits the air dispersion and coarse mineral particles recovery.1.INTRODUCTIONNowadays, flotation is the most widely used separation process in the mineral processing industry. The importance of flotation technology in the global economy is significant. A rough estimate of the quantity of crushed ore treated by flotation is about nine billion tons per year, and the portion of base metals processed using this method is approximately 95% (Brewis, 1996)."

Jan 1, 2018

By l. Bokányi, T. Varga

"The recycling of waste car tyres is a very important environmental task. The waste tyres usually are re-used or recycled by thermal processes like pyrolysis, gasification or incineration. The main problem associated with these processes is the sulphur content of waste tyres originated from the vulcanisation process, which pollutes the environment and the valuable products (i.e. pyrolysis oil) as well. In our research the desulphurisation of waste, mechanically prepared tyre sample was systematically investigated by the biosolubilisation with Acidithiobacillus thiooxidans, strain Karitas. Parallel, the experiments with sterile 9K nutrient medium were also carried out. It was found that the vulcanisation sulphur can be solubilised due to both the bio- and the chemical leaching, although the bioleaching is more effective. The solubilised vulcanisation sulphur then forms precipitates. The precipitates are forming in the bulk solution, as well as on the surface of rubber particles. The origin of the precipitates was investigated using XRD and scanning microscopy with micro probe. The origin of the precipitates is different: while in the process of the vulcanisation sulphur solubilisation with 9K medium the jarosite (KFe3+3(SO4)2(OH)6) forms, the course of the biosolubilisation with Acidithiobacillus ferrooxidans Karitas is accompanied by the formation of the jarosite and the halotrichite (FeAl2(SO4)4 · 22H2O) as well. The formation of the latter is the biomineralisation. The mechanisms of the bio- and chemical solubilisations are rather different as it was found and experimentally proved by several tests, and depends on the retention time of the solubilisation. Special efforts were done to elaborate the proper separation of the precipitates from rubber particles. Combination of intense dynamic stirring and recycling flotation process to remove the precipitates was applied for this purpose. The surface properties of synthetic jarosite were revealed using zeta-potential measurements at different pH and in presence of collectors. The parameters of the flotation were chosen based on the revealed surface properties of the precipitates. Finally, the sulphur recovery of the recycled rubber was achieved as low as <0.5%, sulphur content of it 0.17%, 12-times lower than that of the waste tyre sample after mechanical preparation."

Jan 1, 2018

By Wang Xu, Tao Dongping, Zhang Jie, Tao Youjun

Based on the principle of fly ash triboelectrification, the mineral electrical index and testing method are introduced. The electric differences of various mineral components of fly ash are discussed in view of the results of chemical and mineral composition analysis of the fly ash sample acquired from the Xin-wen power plant. The dielectric constant and charge-mass ratio of carbon and ash in the fly ash are determined. The data were then used along with the rotary triboelectrostatic separator (RTS) testing results to investigate the charging characteristic of fly ash particles in different sizes. The results show that the dielectric constant of fly ash with different particle size decreased with the decrease in particle size, which led to a poor electrical conductivity. Thus particle size has an important effect on conductivity. The charges of carbon and ash particles increased with decreasing particle size. The charge-mass ratio of carbon and ash particles of the same size increased with decreasing particle size. This indicates that finer particle size is more favorable for triboelectrification separation from the charging efficiency point of view. The rotary triboelectrostatic fly ash separation tests show that the best decarbonization performance was achieved with particles in the size range of 0.038-0.074mm with which the decarbonization rate and efficiency index reached 38.93% and 120.83% spectively.

Jan 1, 2014

By G. Mucsi

This paper deals with the laboratory investigation of cathode ray tube (CRT) glass based glass foam, a relatively new product so called ?Geofil bubbles?. The main process engineering material properties of raw materials, such as particle size distribution, moisture content, density and specific surface area are shown. Then the preparation of raw cathode ray tube glass waste is presented including the following steps: crushing in impact crusher, grinding in laboratory scale ball mill, mixing, pelleting and sintering. We found that it was possible to produce foam glass (with proper mechanical stability and particle density) from the investigated waste CRT glass. The material characteristics of the final product strongly depend on the sintering conditions. Optimum conditions were determined particle size fraction was found to be 4-6 mm, temperature 800 0C, residence time 7.5 min. Keywords: waste CRT glass, grinding, pelleting, sintering, glass foam

Sep 1, 2012

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or E-PD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to .2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to .2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: .2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals.The results show that the liberation obtained for gangue was similar (~99%) using either method of comminution. However, the liberation obtained for chromite (~89% vs. ~38%), pentlandite (~50% vs. 1%), pyrrhotite (~56% vs. ~38%), and PGM (~56% vs. ~1%) by E-PD was higher than that obtained by conventional jaw crusher, whereas the liberation obtained for chalcopyrite (~20% vs. ~71%) by E-PD was lower. Nevertheless, the image analysis of the products also showed that the PGM are strongly associated with pentlandite. Thus, for the Merensky Reef, liberation of pentlandite from the gangue minerals and chromite is important to recover more of the PGM. This maybe be significant because, in addition to increased recovery of platinum-group minerals (PGM), Merensky Reef pentlandite also contains significant quantities of valuable platinum-group elements like Pd and Rh (Cabri, 1981; Cabri 1988, Kinloch 1982, Peyerl 1983). Hence, the results indicate that for the Merensky Reef, electric-pulse disaggregation would represent a better comminution operation than a conventional jaw crusher would. In addition, the greatly improved liberation for chromite may find application for the PGM-rich UG2 chromitite."

Jan 1, 2003

By A. A. Sirkeci

In the scope of this investigation comparison between impact breakage and compression breakage were carried out for the separation efficiency of minerals using a chromite ore sample. The ore sample was broken below 1 mm employing a laboratory type roll crusher and an impact crusher. Concentration tests were conducted on -1+0.5 mm, -0.5+0.2 mm and -0.2 mm size fractions using a Wilfley type shaking table. Test results showed a remarkable difference between two types of breakage. Both concentrate grade and recovery was in the favour of impact crushing. Furthermore, the shape of the broken particles also showed differences such that in the case of impact breakage they were more spherical compared to compressive crushing. The results of the shaking table con-centration tests showed that a concentrate assaying 48.4% Cr2O3 were obtained with 78.5% recovery in the case of impact breakage. On the other hand the concentrate grade and recovery values were 48.8% Cr2O3and 52.4% respectively in the case of compression crushing. The losses in the tailings were also in favour of impact breakage proving that differential breakage occurred between chromite and gangue minerals.

Jan 1, 2014

By M. Panayotova

Most of the quantity of the water soluble xanthates, used in mineral flotation, is consumed in the process. However, the residue amounts are water contaminants downstream the mineral processing operations and can be toxic to aquatic biota at concentrations of 1 mg/L. In order to be able to discharge water from tailing ponds to natural water bodies the concentration of xanthates has to be decreased. The present paper studies the uptake of potassium ethyl xanthate by directly modified with copper and lead ions natural zeolitic rock, without passing through zeolite transformation into homoionic form. Modified zeolite exhibits high, comparable with powdered activated carbon of chemical purity grade, capacity to remove potassium ethyl xanthate from model wastewater, with pH in the range of 7?9 and pollutant concentration in the range of 10-150 mg/L. The pollutant immobilization is fast. Both Cu and Pb modified zeolite behave as selective with respect to xanthate in the model wastewater, and Cu-modified zeolite possesses higher selectivity. The equilibrium is best described by the Freundlich equation. Keywords: xanthate, wastewater, modified zeolite

Sep 1, 2012

By V. K. Gupta

Several approaches to the estimation of the size discrete breakage rate and distribution parameters (kj and bi,j ) of the batch grinding kinetic model are available in the literature. Analysis of a large amount of data available in the literature and our own data on several pure minerals and complex ores has shown that it is not always possible to obtain correct estimates of the two sets of parameters using known approaches as several widely different combinations of k and b parameters can sometimes simulate the batch grinding data reasonably accurately. It has been found that there are two main reasons: (i) all size classes are not well represented in the data and (ii) functional forms used for estimation of the two sets of parameters are sometimes chosen somewhat arbitrarily (especially in the case of complex ores), though they are actually uniquely related through size continuous breakage rate and distribution functions. A suitable experimental methodology has been described and demonstrated using some synthetic data and actual experimental data. A mill function approach, which does not require making any assumptions about the functional forms for k and b parameters, is also described and demonstrated. This approach is promising, but requires further development.

Sep 1, 2012

By X. Cui

Hydrocyclone is widely used in closed-circuit grinding process. However, in the first classification operation of coarse particles with high pulp density, the shortcomings of traditional cyclone are that the grinding cycle load is much high, the apex of cyclone is easily to be blocked and classification efficiency is less. Specifically, the problems of traditional cyclone used in grinding process are as follows: (1) Mill utilization factor is low and its handling capacity is small. (2) Coarse particles mixing in cyclone overflow affects the following separation process and fine particles mixing in underflow causes over-grinding, which affects the total recovery rate of valuable minerals. (3) High grinding cycle load leads to large amount of high-density slurry pumping, which causes high energy consumption and severe wear of cyclones, pipelines and pumps. The applications of new type pre-classification hydrocyclone with centrifugal volute in the first classification process of Iron Mine Mill are introduced in the paper. Pulp particles fed in the centrifugal volute were arranged in advance, so that coarse particles can be far away from the overflow pipe, which can reduce the short circuit current to avoid coarse particles entering overflow and improve classification efficiency and accuracy of cyclone. The strong points of the new cyclone in the coarse classification operation are as follows: (1) finer overflow and less fine particles mixing in underflow improves classification efficiency more than 10%; (2) lower ball mill load cycle improves ball capacity more than 10%;(3) grinding energy consumption reduces by more than 20% and cyclone feed pump reduces energy consumption by more than 12%. In short, new type pre-classification cyclone with centrifugal volute solves the problems of fine particles mixing in underflow, high grinding cycle load and less classification efficiency in the coarse classification operation. Therefore, it has broad application prospects in ferrous metal and non-ferrous metal ore dressing plant.

Sep 1, 2012