Search Documents

By K. Bru, D. B. Parvaz

"Electric pulse fragmentation (EPF) is an innovative technology that uses high-voltage pulsed power (HVPP) for the selective comminution of the treated material. Highly energetic electrical pulses are used to fracture rocks at mineral grain boundaries, resulting in extensive micro-cracks and/or complete fragmentation of the processed particles depending on the applied energy. In this study, the EPF technology was applied to a low-grade schist ore containing cassiterite, in order to investigate its influence on the selectivity of the fragmentation. The impact of EPF on subsequent comminution steps was studied by combining either the EPF technology or jaw crushing (used here as conventional crushing) with subsequent impact crushing. The results confirmed the potential of the EPF treatment for a selective fragmentation of the schist ore. This gave the potential advantages of reducing the total energy consumption in the comminution circuit and of improving the recovery of cassiterite during concentration processes. INTRODUCTION The rise in the world consumption of metals combined with the depletion of most of the high-grade ore reserves leads to an increased need to process ores of lower grade, with a more complex mineralogy. To recover the valuable minerals contained in such ores, fine grinding is required, but this process has high energy requirements and leads to the production of a large amounts of fines, which can impede the performance of later concentration processes such as gravimetric separation and flotation. Addressing this issue is a major challenge for the mining industry. Selective comminution methods have the potential to significantly contribute to the profitable exploitation of these low-grade ores by generating cracks specifically at mineral grain boundaries rather than randomly as in a conventional mechanical comminution system. This allows the liberation of valuable components from the feed material without overgrinding, i.e. this prevents unnecessary size reduction of already liberated grains, which leads to a reduction in production of fines and in energy consumption. In addition, rock not fragmented by the process are usually weakened by the dense fracture network generated, which increases grindability of the rock (Wang et al., 2011)."

Jan 1, 2018

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

By Daniela Campos, Aldo Casali, Gonzalo Montes-Atenas

The understanding of the effect of the major variables influencing the froth flotation performance may allow both to predict and to identify best operating conditions towards optimizing the process efficiency. The aim of this research work is to model the effect of dissolved oxygen onto froth flotation performance. Experimental pilot plant results were obtained from a continuous circuit consisting of a ball mill and a rougher bank of four flotation cells. A series of flotation experiments were run with different conditions of dissolved oxygen keeping constant most of other operating conditions. Variables difficult to control were measured or estimated. A set of mathematical models suggested in the published literature were tested. It was found that the copper recovery results were highly sensitive to the concentration of dissolved oxygen. The latter confirmed the reactions mechanisms associated to the collecting capabilities of current flotation reagents used in the flotation of copper sulfide ores. On the contrary, the results of molybdenum recovery varied non-linearly with changes in dissolved oxygen which could not be explained directly in terms of the computed specific rate constants. The error analysis confirmed that Klimpel continuous model exhibited the best specific rate constant correlation with molybdenum recovery data. Lastly, the classic particle force balance equations indicated that the adjustments of estimated mineral liberation with experimental data exhibited a turning point when passing from highly liberated to low liberated particles. The values of recovery for such turning point correlated well with the concentration of dissolved oxygen. The results indicated corrections due to changes in the dissolved oxygen must be incorporated in future froth flotation descriptions.

Jan 1, 2014

By Przybycien Krzysztof, Tumidajski Tadeusz

"Materials being the feed to mineral dressing plants are the mixture of ore minerals having different physicochemical properties among others, especially susceptibility on crumbling. During exploitation of material and their preparation to communition the big number of narrow classes comes into being and they have different properties. The determination of common communition laws of multicomponent (on account of size and mineralogy) materials leads to the estimation of mutual influence of narrow classes and their rates, taking into account their endurance and mineral density, on general ratios and their simultaneous crumbling.If we try to accept the grain membership to the certain component as the differing feature, we can write the balance equation as: ( ) ( ) S= = k i i i g x p f x1where: fi – density functions of one type distribution and of different statistical moments (characterising the homogeneous materials grinding), pi – “stirring” proportions of each components, S== k i i p 1 1 . From the point of verification view of detailed versions of this equation the inverse operation should be done: in the base of the components’ mixture grinding results and the results of components grinding the legitimacy of equation should be checked.The using of finished distribution mixtures’ theories to the grinding process analysis allows, first of all, to verify the assumption of grinding independence of individual feed components. Talking more generally it would lead to the comparison of grain size distributions, obtained by individual components grinding from the defined in the mixture distributions theory calculations. One of experimental and calculation results for artificial mixtures of galena and dolomite is presented on figure below (df means distribution function)"

Jan 1, 2003

By Sebastian Fredes, Williams Calderon, Mauricio Toledo, Gonzalo Montes-Atenas

The influence of the temperature on leaching kinetics of copper-bearing minerals has been widely acknowledged: the leaching of copper oxide ores is generally described as exothermic reactions while copper sulfide ores are associated with endothermic reactions. Reports studying the influence of temperature on leaching kinetics at laboratory scale frequently involve the implementation of either fully flooded isothermal systems or jacketed column setups. Nevertheless, at industrial scale controlling or monitoring the temperature or temperature changes is almost impractical. In fact, leaching process is usually a large tonnage operation and changing the temperature of vast amounts of material would require an enormous amount of energy and highly specific heat transfer equipment. Preliminary computations on the amount of energy required to increase the temperature of a heap or dump in 1°C indicates that it would be impossible to find an energy source able to accomplish the task. In order to provide a solution to this matter it is suggested to create an energy managing protocol (EMP) that permits heat up or down the porous body locally taking advantage from the temperature gradients and from the reactivity of different regions within the material as a function of the leaching cycles. The aim of this study is to evaluate different heat transfer regimes in a 1 ton pilot column leach operation. It was found that best results of copper recovery are obtained when heating up the column in horizontal bands starting from the top of the column moving downwards as the leach cycle evolves. The system is expected to be suitable for industrial applications, but further development of the technique is required, particularly in the design of the heat transfer dispositive.

Jan 1, 2014

By Xingshi Yang, Ghislain Bournival, Seher Ata

"Particle-laden interfaces are a fundamental research topic in froth flotation since the process involves particle-coated bubbles in both the pulp and the froth phase. In most experimental studies the characteristics of the particle layer in multi-bubble systems are poorly defined. An experimental setup has been developed based on a Langmuir-Blodgett (L-B) trough. The modified trough allowed introducing an air bubble beneath the particle monolayer formed at the air-water interface which made the study of the interaction between the bubble and the monolayer under various pH values possible. The monolayer characteristics of the particles were also studied and compared in terms of surface pressure (?-A) isotherms and packing factor. On compression, the particles formed branched structure at high pH whereas a uniform monolayer was formed at lower pH. Observations related to the behavior of particles during compression and expansion cycles, and the coalescence of a bare bubble with the flat particle laden interface were provided and the implication of the results for flotation process was discussed.INTRODUCTIONFroth flotation is known for its versatility and ability to concentrate low-grade, complex ores. It is considered a physico-chemical process in which particles attach to air bubbles, depending on their hydrophobicity as well as other factors, and are carried to the surface to form a froth layer. Reagents are used to stabilize bubbles and the froth layer (Pugh, 1996). However, particles, which are carried by the bubbles or entrained, significantly contribute to the stability of the froth phase (Ata et al., 2003; Zanin et al., 2009; Bournival et al., 2015a). Their relevance in mineral processing has led to a number of fundamental studies on the effect of particles and their properties on the process of froth flotation.Flotation systems are particularly difficult to characterize due to the broad range of properties of particles (e.g. size, liberation, hydrophobicity, etc.) and inconsistent operational conditions (e.g. changes in water quality, reagent addition, etc.). Several studies have made the use of well characterized particles in laboratory conditions. Such studies allowed the finding of an optimal contact angle for the stabilization of the froth phase (Johansson and Pugh, 1992; Ata et al., 2002). Froths have a large number of bubbles so that individual interactions are not observed. The study of two bubbles allows to determine the stability of the bubbles, with particles, and to some extend the stability of the bubble-particle aggregate (Gourram-Badri et al., 1997; Bournival et al., 2015b). The removing of particles between two bubbles may also be studied from a Scheludko cell (Johansson and Pugh, 1992) or by observing a bubble with a flat interface (Sethumadhavan et al., 2002). However, these systems provide limited information on the arrangement of the particles."

Jan 1, 2018

By A. V. Kozub, D. O. Sharkovsky, R. I. Ismagilov

"Due to complex mineral composition and fine ingrained nature concentration of iron ores deposited in Mikhailovskoye mine field requires application of wet magnetic separation to produce 65–66% Fetotal and 8.2–8.6 %SiO2, concentrate with 90–94% of material being –0.044micron grain size. Higher specific consumption of ROM, increase of production costs with concurrent reduction of output - those are inevitable side effects of desired concentrate grade improvement. Large-scale complex analysis and surveys have been carried out aimed at concentrate grade improvement with concurrent output increase. Classification of feed in hydraulic cyclones (hereinafter referred to as hydrocyclones) has been the bottleneck for improvement of processing throughput and concentrate output. Hydrocyclone classification efficiency is 50-60% and further improvement is practically impossible. Actual circulating load may achieve as much as 500-600% while the optimal rate is 200-250%. Application of wet fine screening has been considered to improve iron ore concentrate grade. Objective of this work is to design processing flow diagram for unoxidized ferruginous quartzites with implementation of wet fine screening. Large-scale tests have been run in Crushing and Concentrating Plant with application of wet fine screening stage. These tests included application of wet fine screening in 2 and 3 stages of classification to separate desired grain sized material; replacement of hydrocyclone classification with fine screening; application of fine screening as additional stages to concentration process and screening of final concentrate. Testing Methods. EXPERIMENTS AS WELL AS THEORETICAL RESEARCH HAVE BEEN APPLIED FOR THE PURPOSES OF THIS WORK; INCLUDING MAGNETIC, GRAIN-SIZE AND CHEMICAL ANALYSIS OF CONCENTRATION PRODUCTS. MODERN ANALYTICAL DATABASE HAS BEEN APPLIED TO STUDY WET FINE SCREENING FEATURES, MINERAL AND PHYSICAL COMPOSITION OF CONCENTRATION PRODUCTS. Work Results: - analysis of wet fine screening application for iron ore concentration. - technological solutions enabling to improve slurry classification of fine ingrained low magnetic iron ore have been developed. - effective process flow diagram including fine screening has been designed based on the feasible and reasonable arrangement solutions."

Jan 1, 2018

By Gideon Chitombo

"Mining is a "continuous" process of dependent breakage and materials handling stages, from the initial breakage of the in-situ rock, extraction from the pit or underground, and finally to the surface stockpile and downstream processing. Over time, underground and in-pit mining activities diverged into two separate disciplines, each using a variety of in-situ breakage techniques and surface activities, with processing techniques dependent on mineralogy or grades. This artificial separation of underground and open pit activities was exacerbated when the two became increasingly managed as separate cost centres rather than as an integrated unit. Mass mining essentially began in 1903 when metallurgist Daniel Jackling initiated the world’s first open pit, mining system at the Bingham Canyon porphyry copper deposit in Utah. The term mass mining has since been construed to mean large open pits and cave mining methods, including their variants. These methods are largely non-selective, involving the mass extraction of a deposit irrespective of the uneven distribution of grade and mineralogy. The advantages of mass mining have historically applied mostly to low grade, large scale deposits. With the depletion of mineral reserves closer to the surface, however, new deposits are deeper, lower grade and mixed with more impurities. These and other factors make extraction more difficult and costly. Mass mining is moving rapidly into a new and less certain environment where revolutionary changes are required to effectively deal with future challenges which are technical, economic and environmental (licence to operate). This keynote address presents current initiatives being considered for the next generation of both underground and surface mass mining systems in order to significantly reduce lead times and mining costs (CAPEX and OPEX), substantially increase productivity and meet license to operate requirements. The address is designed to solicit discussion on how better integration of mining and processing can become a platform for these next generation of mass mining systems and can also help the industry deal with the future challenges."

Jan 1, 2014

By S. Makni

Flotation is a complex process in which many mechanisms come into interaction. In this paper, an approach to model these mechanisms in order to predict size-by-size flotation performances is presented. The estimation of the collection efficiency of particles takes into account the serial sub-processes of particle-bubble collision, attachment and detachment. The model was applied to an industrial plant and yielded satisfactory results whereby the actual flotation performances could be correctly predicted. Furthermore, the flotation model allowed investigating the possibility of improving flotation performances by a split flotation feed in comparison to the actual single-stage process.

Sep 1, 2012

By Sudhir Srivastava

India hosts a wide range of globally significant mineral resources, including four fuel minerals; 11 metallic minerals; 22 minor minerals and 52 non-metallic minerals. The country ranks among world?s top five nations for its commodity reserves of coal and iron ore. Interestingly, only small part of country's landmass has been explored that provides opportunity for future substantial mineral discoveries. India plans to double infrastructure investments to US$ 1trillion. Despite the challenges in infrastructure project implementation, mining sector remains a key driver of demand growth for commodities in the years to come with a good prospect to grow in future.

Sep 1, 2012

By Thomas Pretz, Alexandra Pehlken

Sampling of municipal solid waste is known to be difficult to sample if it has to be representative. When dealing with municipal solid waste, the usual method is to study separately waste material below 40 mm and particles bigger than 40 mm. The material < 40 mm cannot be sorted manual and is termed the “fine fraction”. The particles > 40 mm can be separated manually and are usually sorted into pre-defined groups of materials. These groups can be defined depending on the demand of quality assurance. But standardisation of procedures is not far progressed, even for the widely practised sorting methods.

Jan 1, 2003

By Andrey V. Tarasov

"An environmentally clean and virtually waste-less technology for treatment of domestic and industrial solid waste (HGIW) including other toxic chloride-containing materials has been developed and proven on a full scale by the Gintsvetmet Institute in cooperation with some other Russian organizations.The essence of the process is that the HGIW are decomposing in the liquid base in air-bed slag melted layer under the temperature of 1350-1400°C.HGIW is considered as fuel heat-producing energy of 1500-1800 kCal/kg with 51,7%.Processing of municipal and industrial solid waste in molten slag is carried out autogenously without additional fuel, the blowing is enriched by oxygen up to 50-70%.The complex makes it possible to treat the furnace charge without preliminary drying and sorting with big differences in chemical and morphological composition due to the versatile firing chamber.The proposed process resolves the acute and globally significant problem of dioxin formation.The purpose of the proposed technology is to ensure such destruction of the structural lattice that would guarantee irreversible transformation of the resultant substances to prevent formation of dioxins. It was established the required preconditions to achieve this purpose."

Jan 1, 2003

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

Pyrite is one of sulfide minerals most widely distributed in the earth. During the flotating separation of metal sulfide and the floating desulfation of coal, it is often requaired to restrain pyrite. However, the result is not very satisfactory because of the little difference of floatability of minerals to be separated. The problem is extremely outstanding for the floating desulfation of coal. Researchers carried out a number of experiments with T. ferrooxidans (Yang et al, 2001; Zhou et al, 2000; Zhou et al, 2001; Wei et al, 2001) for an enhanced restraint to pyrite. The results showed that the T. ferrooxidans after being cultured works the best in restraining pyrite. After 10 min pretreatment, the removal rate of pyrite from coal is up to 80%~90%. The research results by Yuan Xin et al (Yuan et al, 2000) show that T. ferrooxidans can restrain effectively the floatability of pyrite and can reduce the recovery of pyrite from 95% to 8%. Though the restraining properties of T. ferrooxidans to pyrite have been proved by many tests and experiments, there are very limited reports on its restraining mechanism. Thus, a systematic experimental research is carried out in this paper.

Jan 1, 2003

By Vincent C. Smith, Agit Singh, Daniel de V. van der Spuy, Bernard Muller

"Process control in the minerals industry is made difficult by factors such as the multivariable nature of the processes, noise, many disturbances, the changing nature of the processes, nonlinearities, process constraints, slow responses and large deadtimes. A good example of such a process is a milling circuit, where all these problems are experienced. Since model predictive control (MPC) effectively handles most of these difficulties, Mintek decided to develop, customise and test an MPC controller for milling control.Conventional MPC uses a dynamic model of the plant to calculate the future (predicted) plant outputs based on the movements of the manipulated variables in the past. The future moves of the manipulated variables can then be calculated using an optimisation algorithm that will minimise the difference between the setpoints and the predicted outputs. The least squares optimisation method is the quickest, but it does not cater for process constraints. Constraints can, however, be handled explicitly by using a quadratic programming optimisation method. This method ensures that the variables stay within the constraints at all times, but the calculation procedure is much more computationally intensive.• modifying MPC for the Minerals Processing IndustryIt was found that in order to obtain good, robust control using MPC in the minerals processing industry, the conventional MPC algorithm had to be adapted. The MPC controller was first tested on an extensive milling simulator, which was specifically developed for that purpose. Problem areas were identified and the MPC controller was specially adapted to accommodate for these difficulties. Some of the adaptations to the conventional MPC algorithm and special features added were as follows:Since milling plants contain many integrating processes (e.g. sumps), and integrating errors can cause offsets and poor control, it was essential that integrators be handled explicitly. This problem was solved by adapting the algorithm and also using an integrating error portion to compensate for integrating errors.Constraints on the inputs and outputs adversely affected the control. The controller using simple least squares optimisation was tuned with the constraints in place, while the maximum expected setpoint changes were made. This ensured that the process would be able to handle most setpoint changes up to these expected values without violating the constraints. A later improvement on this method was the incorporation of a quadratic programming algorithm to perform the optimisation. This method handles limits explicitly and was shown to perform better than the least squares methods (at the expense of a much higher computational cost)"

Jan 1, 2003

By Megha Patel

"The objective of this project was to investigate the application of Prompt Gamma Neutron Activation Analysis (PGNAA) technology to provide real-time on-belt elemental analysis of feed ore in base metal sulphide processing, in this case at the Mount Isa Mines Zinc-Lead Concentrator Heavy Medium Plant (HMP). After initial exploratory testwork proved successful, a Geoscan On-Belt Elemental Analyser was retrofitted onto the existing HMP feed conveyor. Dynamic calibration of the Geoscan was conducted based on laboratory XRF analysis results of the HMP feed conveyor hammer autosampler samples from May to November 2013. Comparison of the Geoscan results to the laboratory XRF analysis results during and after dynamic calibration indicated the technology had acceptable accuracy to be incorporated into HMP process control. The variation between the two sets of data includes all primary sampling, sample preparation and XRF analysis errors as well as the Geoscan errors themselves. The Geoscan instrument precision must be calculated separately through a duplicate sampling campaign and independent laboratory analysis before extending the scope of its range of application beyond HMP process control. The expected benefits of integrating the Geoscan real-time data into HMP process control are optimised HMP metal recovery, improved cost efficiency and improved stability of the downstream processes (milling and flotation). Utilisation of the Geoscan will also enable improved feedback to mines on grade control and dilution, and provide additional information on individual ore types when fed as campaigns to HMP."

Jan 1, 2014

By Hans-Åke Häggblad, Bertil I. Pålsson, Jan Stener, Kent Tano, Andreas Berggren, Pär Jonsén

Numerical modelling of grinding in tumbling mills is traditionally done with the discrete element method (DEM). The grinding balls are then represented by DEM particles and the mill structure is considered rigid. To include more physical phenomena several numerical methods can be combined. One important improvement is to include the mill structure response, using the finite element method (FEM). The interaction between charge and lining can then be studied in detail. The pulp can also be included using a particle-based continuum method e.g. smoothed particle method (SPH). The strength of SPH lies in modelling of free surface flows and very large deformations and it is suited to model simultaneous fluid and granular flow. Still, the coarse particles (grinding balls) in the charge are suitable to be model using DEM. Each of these methods has their strength and weaknesses, but combined they can successfully mimic the main features of the charge movement. With these numerical tools the complex interaction between the different components of the grinding process; pulp, charge, lining and the mechanical behaviour of the mill, can be studied together. This work will present novel numerical approaches to model, simulate and validate charge behaviour in tumbling mills. These numerical models give possibilities to better understand the physical and mechanical behaviour of particulate material systems during grinding in a tumbling mill. This is important in order to develop and optimise future high-capacity grinding circuits and save energy.

Jan 1, 2014

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.One of the simplest separators is the sluice, in which separation takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in so-called hindered settling mode.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates.The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ‘law of the wall’ model.Particle concentration distributions were described using Hunt’s sediment transport model, assuming the particle eddy diffusion coefficient to be the same as that for the water. Settling velocities were calculated using either the Richardson and Zaki or Brauer and Thiele models. The latter takes into account particle size and density distributions and solids volumetric concentration.The resulting predictions of particle separation are remarkably good, even though the model does not model the local settling velocity in the slurry."

Jan 1, 2003

By Rogerio C. Guimarães, Antonio E. C. Peres

The production of phosphate concentrates (phosphate rock) from slimes represents a challenge to the phosphate industry worldwide. In Brazil, this challenge is particularly relevant due to the consistently low P2O5 grades and the igneous origin. The first industrial experiences of producing phosphate rock from slimes (-44µm or -325#) fraction started at Arafertil, currently Bunge Fertilizantes SA, in Araxá, in the 1980.s. This production corresponds, nowadays, to 35% of the total production of concentrates in the company (830,000t/year) in a circuit consisting of desliming in 40mm microcyclones and concentration in flotation columns, corn starch and fatty acids being utilised as reagents. The performance of slimes flotation and the process control, at Bunge´s concentrator, were improved after the introduction of column flotation technology, in the first half of the nineties. The column flotation technology for slimes recovery was expanded to other Brazilian concentrators still in the nineties: Ultrafértil (Catalão - GO), Bunge (Cajati - SP), Fosfértil (Tapira - MG) and Copebrás (Catalão - GO). At present the Brazilian production of phosphate rock is approximately 4.5Mt/year, with a strong trend for a market increase. Genuinely Brazilian technology is utilised for the processing of slimes, the concentrates representing 11 to 13% of the overall production. The production of apatite concentrates from slimes was relevant to increase phosphate recovery and reduce costs, contributing to the growth of the fertilisers industry.

Jan 1, 2003