Search Documents

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015

By Thomas D. Humbert, Christopher J. Ramsey

Construction of a new underground parking structure in State College, Pennsylvania, is situated on a site constrained by limited ROW and required excavations ranging in depth from 25 ft to 40 ft. Additional complications included busy surface streets, an active intersection, and numerous underground utilities that could not be disrupted by construction activities. To combat these challenges, an innovative approach for earth retention was designed that combined multiple types of retention systems. The overall system included alternating sections of soil nail walls and a hybrid system of soldier pile walls (consisting of micropiles) that were partially restrained by a soil nail wall in the lower portions of the excavation. Further, due to the limited space within the property limits that inhibited the length of the permanent nails, the wall design team collaborated with the project designers to develop a solution such that the completed wall became an integral part of the final design/construction of the underground parking structure. INTRODUCTION HERE at State College is a mixed-use, high-rise building in State College, Pennsylvania. The 12-strory building has up to 3 levels of below-grade parking, with the above-grade levels consisting of residential and commercial/retail space. The existing property was a parking lot bound by the streets Calder Way to the north, Garner Street to the east, East Beaver Avenue to the south, and Heister Street to the west. The overall property sloped approximately 20 ft in elevation from southeast to northwest. Excavation for the below-grade levels extended 21 ft to 36 ft (6.4 m to 11 m) below street level. During design-development phases of the project, it became evident that due to subsurface conditions and right-of- way limitations, conventional construction techniques would not be feasible. The full perimeter of the excavation would require earth retention including the weak shale bedrock along the bottom of the excavation. The project developer (CA Ventures) and general contractor (Brinkmann) coordinated with the specialty contractor and wall design engineer to find a solution. At this time, Coastal Drilling East (specialty contractor) and Wood Environment & Infrastructure Solutions (wall design engineer) became involved. The project developer and general contractor were aware they needed an earth retention system, but given the many variables the project faced, a single, straightforward solution would not work in this application.

Jan 1, 2019

By Ryan Weaver, Travis Coleman

The drilled shafts that support transmission lines and substations have been increasingly subject to testing to assess the integrity of placed concrete. Cross-hole Sonic Logging (CSL) has been used, but large diameter shafts with challenging site access are generally more favorable to Thermal Integrity Profiling (TIP) testing. TIP testing assesses the shafts based on measurements of the concrete temperature during curing. The TIP results provide assessment of integrity both within and outside the cage, along with information about the alignment of the cage and concrete cover. This data has allowed shafts with imperfect results to be subject to more detailed structural evaluations. However, it may not be well understood how to use this additional information by designers and engineers. The purpose of this paper is to present TIP results of transmission line foundations, both with and without issues with integrity, including cage shifting, minimal concrete cover, or soil inclusions. The intent is to provide general guidelines of the issues that merit additional investigation and those that should be recognized as inconsistencies inherent to underground construction. BACKGROUND This paper is intended to discuss some of the drilled shaft evaluations made when TIP testing is performed. The authors of this paper were recently involved with a transmission line project that was designed and constructed for a Confidential Utility Client located in the Midwest United States. The project was delivered as an Engineering, Procurement, and Construction (EPC) contract with the electrical line construction company as the prime contractor. The contractor then subcontracted several parts of the work which included engineering for transmission line and foundation design, foundation construction, and third-party testing intended to evaluate the concrete homogeneity and integrity of the place concrete in the deep foundations. The testing method selected was Thermal Integrity Profiling Method B, which uses thermal sensors embedded in the concrete. The TIP testing was administered by Mr. Travis Coleman with GRL Engineers, Inc. Mr. Ryan Weaver with Burns & McDonnell served as the owner’s engineer and technical consultant for the utility and was responsible for reviewing submitted TIP reports and providing recommendations to the utility on their acceptance, and if there were any issues that would warrant further discussion and analysis.

Jan 1, 2019

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By Ben M. Lewis, Yogesh Prashar

"The East Bay Municipal Utility District (EBMUD) is a major water utility service providing water to over 1.3 million people in the eastern San Francisco Bay Area. EBMUD manages 28 dams at 5 terminal and 23 open-cut reservoirs within a 331-square-mile customer service area. As part of a 2012 update on EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, EBMUD has decided to replace Central Reservoir, a 152.8 milliongallon open cut reservoir, with optimally sized tanks. This paper presents the results of an analytical comparison of various foundation reinforcement solutions for the proposed tanks including: Cement Deep Soil Mixed (CDSM) columns, vibro stone columns, rammed aggregate piers, and lightweight cellular concrete fill. The computational program GeoMat (www.ensoftinc.com) was used to perform simplified soil structure interaction analyses. Settlement estimates were developed for each alternative with the proposed loading and compared to an allowable differential settlement criterion established at 0.3-inches over a 50 foot length. The authors wish to present the importance of considering mat and soil interaction along with various settlement mitigation methods considered for this challenging project.INTRODUCTIONProject BackgroundCentral Reservoir is an operational open-cut reservoir located north of the intersection of 25th Avenue and East 29th Street in Oakland, California. The reservoir is bound by 23rd Avenue to the west, Sheffield Avenue to the east and Interstate Highway 580 to the north. Originally, the Central Reservoir site was a drainage swale incising into weathered bedrock formed from Pleistocene alluvial deposits. The reservoir was first constructed in 1910 by excavating a basin below grade and constructing an embankment dam on the south and cutting/filling the bedrock and alluvial deposits from the drainage swale. The main dam at the Central Reservoir site is also a DSOD (Department of Safety of Dams) jurisdictional dam and as such is regularly monitored by the EBMUD Materials Engineering Section and the California DSOD.In a 2012 update to EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, Central Reservoir was identified as a critical facility that has reached the end of its useful life and must be replaced due to: a failing panel craft lining which contains polychlorinated biphenyls in the interior coating, a roof that does not meet the current seismic code, and reduced operating levels due to potential leakage in the upper portions of the panel craft lining. Furthermore, Central Reservoir is about three times larger than required and is located at a lower elevation than other regional reservoirs in the pressure zone resulting in increased labor-intensive operational challenges and water quality operations.This project presents some challenging geotechnical demands – the site is founded on weakly consolidated Holocene Alluvium overlying weathered bedrock, the proposed structural loads are large, and the new Central Reservoir is to be placed on a pad at an elevation of 182 feet, required placement of up to 30 feet of fill over the current basin. Additionally, the project aims for a long-term foundation solution that will outlive the new replacement tanks and accommodate future site upgrades. In order to meet this goal, the differential settlement criterion for the tanks was ¼ inch over 50 feet length. Lastly, the project also aims to address EBMUD’s increasing trench spoil stockpiles by recycling discarded trench spoils as fill for the proposed tank pad."

Jan 1, 2016

By Chris Leach, Lucie Spencer

This case study describes the geotechnical aspects of the basement construction for a multi-storey, residential and hotel complex located in the newly developed Elizabeth Quay precinct in Perth, Western Australia. The development included a three-level basement for car parking covering the full site area which was constructed using the top-down construction sequence. Soil conditions generally comprised 2m of fill overlying medium to dense clayey sands that in turn were generally overlying a very stiff clay stratum at approximately 13m depth. Bedrock level was generally encountered at approximately 22m to 35m below ground level. The ground water table was at a depth of approximately 1m below the existing ground surface level. A site boundary basement wall was constructed using a diaphragm wall retention system. The majority of the vertical loads from the building were transferred to the Kings Park Formation (KPF) bedrock through the use of foundation piles constructed by the CFA method. The CFA piles were installed from existing ground level, resulting in approximately 9m sacrificial concrete length from pile platform level to basement 3 (B3) level. The permanent column loads are such that a single CFA pile was not structurally adequate. To allow a full CFA foundation system to be adopted, an innovative design and construction approach was developed for these heavily loaded columns. This paper discusses the site technical details and the design and construction aspects required to meet the challenges offered by this project.

Nov 1, 2022

By Muttharam M, Karthick Kumar V

Helical piles foundation systems have been extensively used in engineering application. It is commonly adopted to resist the compression, uplift force, overturning moment and lateral forces. Helical pile system is extensively used in many structures such as Transmission towers, Wind farms and other offshore structure because it is easy and quick to install. Realizing the importance of helical pile, an attempt is made in the present investigation to bring out the effect of spacing between the helix, blade thickness, and shaft thickness through numerical analysis. To validate the finite element model experimental investigation was carried out. In this investigation model steel piles with dual helical plate embedded in clay bed with the consistency of 0.4 was tested to study the effect of uplift loading on the behaviour of piles in tensions. Model helical pile with 12.5 mm diameter circular shaft and helix diameter of 25 mm. The model pile embedded in clay bed for a depth of 400 mm. Parametric analysis of helical pile by varying blade thickness, shaft thickness, and the spacing of helix was carried out by using Finite Element tool Plaxis 3D. From this analysis, an increase in thickness from 4 mm to 10mm increase the uplift load. Similarly, an increase in spacing of helices from 0.5 m to 1.5m increase the uplift capacity beyond that it decreases the uplift capacity. By keeping the contact area of the helix as constant as the number of a helix and helical spacing was varied, the critical number of the helix was found as 2 and the critical spacing of helix was found as 1.5 m for this study.

Nov 1, 2022

By Jim Glider, Noah Miner

The Gordie Howe International Bridge is a project to build a cable-stayed bridge and border crossing across the Detroit River. With a span length of 2,800-ft (853.4 meters), the Gordie Howe International Bridge will have the longest main span of any cable-stayed bridge in North America. Each tower has two legs that are supported by six drilled shafts each for a total of 12. The tower shafts are 9.84 feet in diameter (3-m) and extend well into bedrock. 17 each, 6.6 feet (2-m) drilled shafts were built to support the aging river bulkhead and replace shipping bollards. In addition to shallow groundwater fed by the Detroit River, artesian conditions at depth result in a water head that is approximately 17.2-ft (5.2-m) above surface. At 95-ft (29-m) below grade Dundee Limestone, of the Detroit River Group, is moderately weathered and fracture density decreases with depth. The Dundee Limestone strength ranges from 8-ksi (55.1-MPa) to 12-ksi (82-MPa) and may carry hydrogen sulfide in fractures. Working through casing that sticks three stories out of the ground is less than ideal, but was necessary to maintain a positive fluid head and prevent artesian-related quality issues. The sheer scale of the bridge forces required a load test configuration that could impart an equivalent static load of over 38,000,000 pounds (170-MN). A suite of QA/QC tests was developed to ensure the shafts would meet the project plans and specifications to include critical base cleanliness criteria. Interesting CSL and TIP results obtained highlight the strengths and weaknesses of each test method. Cleaning drilling fluids with a centrifuge allowed recycling of product and reduced exposure to environmental contaminate exposure. Having large construction equipment working next to the river presented challenges in working pad design. A driven pile system was developed to support high oscillator forces and protect the aging seawall.

Sep 8, 2021

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By Christian Leble, Dr. -Ing. Jakob Vogelsang, Dr. -Ing. Oksana Solt, Dipl. -Ing. Joachim Meier, Dr. -Ing. Wolfgang Orth

In the course of closing the gap between the Brandenburg Gate and Alexanderplatz, the Museum Island station was built by Implenia Construction GmbH. The tunneling for the platform hall took place on a length of about 106 m (347 ft) under the protection of a major ground freezing measure and crossed the Spree canal as well as the listed castle bridge. The approximately 20,000 m³ (4.54 E+06 US gal dry) frozen mass lay mainly in the Berlin sands. In order to ensure safe tunnelling and to protect the adjacent buildings, the planners had defined requirements for the mean freezing temperature and thickness of the frozen mass. For a reliable conclusion on the dimensions of the frozen mass, we used innovative temperature sensors as well as the new, web-based 3D measurement visualization and the associated site-specific evaluation software. The largely automated evaluation enabled a quick and reproducible determination of the temperature distribution in the frozen soil and its thickness in the relevant cross-sectional areas. The measurements were validated by thermal calculations using the Finite-Element-Method. Thus, an objective and clear assessment basis was available to ensure rapid coordination between stakeholders. The evaluations provide new insights into the temperature influences from tunneling, the application of shotcrete and the concreting of the inner shell. The newly implemented active thawing system is also an interesting innovation.

May 1, 2022

By Alexander Filotti, Richard Kalson

"1. INTRODUCTION- WHAT IS P3 OR PPP ?The Public Private Partnership (PPP or 3P) is a project delivery scheme based on the government providing land and/or a concession agreement, and on a private entity providing the design, construction, financing, operation and maintenance of the project for an extensive duration of time (up to thirty years). At the end of the operation-maintenance period, the project is turned over to the public entity, which fully owns the project at all times. While there are many PPP delivery schemes used around the world, for the present paper, we are going to analyze the impact of the Design-Build-Finance-Operate-Maintain (DBFOM) scheme on the deep foundation specialty subcontractor. There are couple of reasons that the PPP delivery system started to be used and implemented not only by developed nations (e.g. United Kingdom, USA etc.), but also by the International Development Bank for delivering major infrastructure projects in developing nations. From the point of view of government agencies, some of the reasons to use PPP are the following:??The primary use of private capital in an era where borrowing and/or supplemental taxation represents too much of a political risk. Budget deficits and taxation limits are extremely hot topics in every election (national or local) and the level of education of the electorate in this area is making it more and more difficult for politicians to use borrowed funds and additional taxation finance sources for public projects. At the same time, we see an increase in the social expenditures of the government in parallel with a needed increase in expenditures on infrastructure due to aging and neglect.??Bundling the construction risks with the operational and maintenance risks naturally pushes the private entity to increase the level of innovation and communications in the primary phase ( the construction phase) in order to develop future process based upon the innovation and communications utilized in the operation and maintenance phase of the project. This is true if contractual incentives are properly structured because “all revolves around incentives. In a world of ‘incomplete’ contracts, where it is difficult to foresee and contract about uncertain future events, it is important to get the incentive structure right” (Grimsey and Lewis, 2004).??The transfer of very expensive risks such as differing site conditions, schedule, design, construction, maintenance and operation costs from the public authority to the private entity.??The timespan of development and construction of a PPP project is usually shorter than the traditional procurement process (e.g. “ the I-595 P3 provided capacity improvements fifteen years sooner than a conventional plan would have offered. In Maryland, an innovative expansion of the Seagirt Marine Terminal in the Port of Baltimore was completed two years ahead of schedule due to the P3 model. As a result, the Port of Baltimore is only the second port on the US East Coast to have unrestricted access to both a fully functioning 50-foot channel and 50-foot berth.”)"

Jan 1, 2017

By K. Madhusudan Reddy

Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load?deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.

By Mohamed A. Eliwah

This paper deals with the determination of hydraulic conductivity of the coastal coralline limestone aquifer of Jeddah, Saudi Arabia. This coastal area has witnessed urban development and establishment of towers which requires deep foundations, excavation and dewatering of huge quantities of unconfined groundwater. It is occupied with successive layers of soft detrital and consolidated massive cavernous coralline limestone of the Quaternary age. These layers are encountered at a depth of 1.5m and extend for more than 100m. Hydraulic conductivity values were obtained by analyzing the pumping tests data under steady and transient state conditions. Hydraulic conductivity values help in selecting the proper and safe dewatering system, as well as determination of discharge rates and quantities of groundwater to be withdrawn. Test results obtained from two surveyed sites showed that the values of hydraulic conductivity are greatly variable. It ranges between 118.1 and 1559.6 m/day at the first site, whereas at the second one it ranges between 94.6 and 350 m/day. These high values are attributed to the cavernous nature of the water-bearing formation. Jeddah city could be divided into three different dewatering zones extending from north to south parallel to the coast line. Well point dewatering system could be applied in the first zone while ditches and sumps are the most suitable dewatering method in the second and third zones. Dewatering using deep wells in such highly permeable formation will require withdrawal of huge quantities of water which will be accompanied by washing out fine sediment filling the cavities in the surrounding areas. This will badly affect the nearby buildings through settlement, crakes and other structural damages. Therefore, construction of grouting plug/blanket with thickness of 3.0 m at a depth of 20.0 m is recommended. This depth will be enough to support the plug against the hydrostatic pressure. Moreover, it is highly recommended to transfer the site into closed box, by using diaphragm walls or secant bored piles.

By Adel Hanna

Earth pressure acting on piles driven in sand is playing a major role in estimating pile capacity. In literature, researchers entertained simplifying assumptions in estimating the earth pressure acting on the pile's shaft, ignoring the effects of pile installation and pile size. Empirical formulae were introduced based on laboratory or field test results, where major discrepancies can be found among these formulae. In this paper, the theory of cavity expansion and the finite element technique will be used to establish the effects of pile installation technique and pile's diameter on the earth pressure acting on the pile's shaft and accordingly on the values of the existing coefficient of passive earth pressure and overconsolidated ratio. It is of interest to note that pile driven technique and pile's diameter have significant increase on the earth pressure acting on the pile's shaft and accordingly on the overconsolidation ratio in case of loose or medium sands, while they may cause crushing and dilation in case of dense sand. Keywords: Single pile, Cavity expansion, Cohesionless soil, Driven piles, Numerical modelling, Finite element technique, Earth pressure.

Jan 1, 2003

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Steven R. Ahlfield, Ali Ghandeharioon

A wastewater treatment plant commissioned in 1978 is undergoing a major expansion. Planning various phases of the 8-hectare expansion at this site requires an understanding of the site response during and after construction, and the potential impact on adjacent properties and infrastructure. The expansion project requires nominally 5 m of site grading fill for flood protection. The site is underlain by loose to compact fine sand over firm to very stiff clay stratum that extends to great depths. Ground improvement is required to mitigate the liquefaction hazard in the fine sand stratum, and preloading is proposed to reduce post- construction settlements in the deep clay. Site development and foundation systems for the plant expansion project were evaluated by conducting settlement analyses which accounted for the historic and future site loading and 3-D modeling of soil layers with interpolation between borehole and cone penetration test (CPT) locations. The numerical model was calibrated to match short-term and long-term settlements measured at the plant site. The analyses were carried out to assess the effects of past loading, proposed preload and surcharge heights, lateral extents and durations as well as vibro-replacement ground improvement on post-construction settlements. Two design options were considered for the preload footprint across the site and foundation system for proposed facilities. It is shown that limiting the preload extent and founding some of the proposed structures on deep friction piles reduce the predicted settlements of adjacent infrastructure and result in reasonable performance for the proposed facilities. INTRODUCTION A wastewater treatment plant commissioned in 1978 will be replaced with a new plant on an undeveloped portion of the site to provide wastewater treatment for an expanded service area. The existing facilities must remain in operation until completion of the new plant. The site grade will be raised nominally 5 m for flood protection. The large areal extent of the site grading fill and plant structures will cause stress changes extending to great depths in the underlying soils and result in settlement of the existing and new structures. Historic settlement of the existing facilities has been tolerable for plant operations, but no settlement performance data was recorded during site development and post-construction from 1978 to 2007. Development of the 8-hectare expansion at this site is planned in three phases to reduce the overall construction schedule. Planning for each phase requires evaluating the effects of various site development activities from start to completion of expansion and during the design life (i.e. post-construction period), and the potential impact on existing wastewater treatment facilities and adjacent properties and infrastructure including an adjacent viaduct structure. Figure 1 presents the site plan and three distinct site development phases considered for the plant expansion.

Jan 1, 2019