Search Documents

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By M. Keen

The backfill system at Cleveland Potash?s Boulby Mine places waste filter cake underground in the form of a high concentration slurry in worked out areas of the mine reducing the mine?s environmental impact. The backfill system delivers slurry approximately 1100 m down the mine and up to 11 000 m horizontally underground. The Boulby backfill system is unique in that the placed backfill waste is not used for the usual purposes such as support, pillar extraction or reducing ventilation requirements. It was specifically implemented for environmental reasons. This influenced the design and resulted in some unique features of the system. A previous paper (Wilkins et al., 2004) described the design and commissioning of the backfill system. This paper describes the operational experience with the backfill system and backfill placement since commissioning in May 2003 and looks at lessons that can be applied in other backfill designs.

May 1, 2007

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

Leadership "Organizing a group of people to achieve a common goal" Paradigms ? Rush to produce or cut costs. ? The most important thing after safety is production. ? We?ll take care of ??this?? once in production. ? I know what to do, 30 years of experience in mining. ? I want a 100% reliable operation.

Aug 1, 2013

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Gold Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840-1200 um in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding, smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840-1200 um class reported to the 600-840 um; this figure is much higher than for silica ( 46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50-100 um to 20 at 500-1000 um.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840-1200 um to the 600-840 um class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photographic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase overall gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydrocyclones takes place at a much finer cut-size than ore, 20 vs. 57 um. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3"") Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89 to 92% for the PCUF and secondary mill discharge, 89 and 92%, respectfully."

Jan 1, 1991

By C. Veloo

"Westmin Resources operates a mine/mill complex at Myra Falls and produces copper and zinc concentrates with minor associations of gold, silver, and lead from a polymetallic, massive sulphide orebody. Mill flotation performance has historically been plagued by periods of uncontrollably high circulating loads leading to low concentrate grades and below optimal tails. This led to a detailed examination of the flotation process. Locked cycle, and pilot plant data are presented. In addition, plant design and commissioning as well as column cell details are discussed. A comparison between actual and predicted performance is also presented. Benefits realized are higher copper and zinc concentrate grades and improved zinc recovery.PrologueMyra Falls Operations is located at the south end of Suttle Lake in Strathcona Provincial Park. Access to the mine site is provided by a 90km paved highway from Campbell River, British Columbia.The mine and facilities are nestled in the narrow Myra Valley between Mount Phillips and Mount Myra. These steep, rugged mountains rise from the valley floor at an elevation of 900 feet to summits of almost 6000 feet. The steep slopes are heavily wooded with fir, hemlock, and cedar up to an elevation of 4000 feet where a transition to alpine meadows occurs. The summits are craggy rock faces, some capped with glacial ice. Myra Creek winds its way through the valley dropping several hundred feet into Suttle Lake. Precipitation is high at over 100 inches per year, which may include up to 10 feet of snow in winter. The temperature may range from 32° C in summer to -18° C in winter.Myra Falls began production in 1965 with the Lynx Mine, supplemented by the Myra and Price Mines in subsequent years, feeding a 950 stpd mill up until the middle of 1985 when the H-W mine was brought into production. The original mill was replaced with a modern 2700 mtpd facility and in 1988 production was increased to 4000 mtpd.Both Lynx and H-W mines are currently in production producing an average of 3650 mtpd. The ore minerals are primarily sphalerite and chalcopyrite, with subordinate galena, bornite, tetrahedrite, and electrum."

Jan 1, 1992

By Julie Culverhouse, Dennis Grimm, Kieran Harding, Jean-Francois Boulanger

"Agrium’s Canadian Phosphate Business (CPB) is comprised of Kapuskasing Phosphate Operations (KPO) in Northern Ontario, Canada’s only operating phosphate mine, and Redwater Phosphate Operations (RPO) in Alberta, which manufactures the fertilizer from KPO’s concentrate.Production from KPO’s South Pit commenced in 2009 and introduced contaminant problems: high aluminium from crandallite and kaolinite clays. These issues caused a drastic decrease in P2O5 recovery and throughput in both plants. KPO attempted to reduce Al clays by means of aggressive desliming. Meanwhile RPO experienced high amounts of dissolved metals in their feed that are detrimental to fertilizer production.This paper covers the mineralogy of the problem, its impact on contaminant separation at KPO, on RPO’s process and on Agrium’s Canadian Phosphate Business as a whole.Potential solutions to the problem are discussed and analysed, including a process change to deslime high aluminium streams more aggressively and high grade ore flotation, which is atypical at KPO. The latter is a demonstration of the value of communication between the concentrator and the client, as KPO accepted a recovery loss and increased production costs in order to increase overall CPB profits. General lessons learned are discussed, followed by a section on ore blending.INTRODUCTIONAlthough the existence of the Kapuskasing phosphate deposit has been known since the 1970s, it’s only since 1999 that Agrium has been operating the Kapuskasing Phosphate Operations (KPO). The mine consists of three major pits (Center, North and South) from which a mining contractor hauls the apatite ore to the Agrium concentrator. The beneficiation plant processes the ore, separating contaminants such as Fe, Mg and Al which are detrimental to its client, Agrium’s Redwater Phosphate Operations (RPO). The KPO concentrate is finally thickened, filtered and dried before being shipped by rail to RPO.At the Redwater plant, the KPO concentrate is added to a sulfuric acid solution in an attack tank, to create a phosphoric acid solution and gypsum:"

Jan 1, 2011

By W. Chi, R. Regan, R. A. Washington

"In uranium mines, the purification of underground mine air can be accomplished by the removal of dust particles and radon daughters using filters. Full-scale statistically designed experiments with flow rates up to 10,000 cfm have been conducted at Denison Mines Ltd. on mine air filtration with vermiculite as a filter material. Various filtration bed thicknesses were chosen, with different face velocities through each bed thickness. Results on total dust, respirable dust and radon daughter collection efficiencies were analysed statistically. It is shown that these collection efficiencies are directly related to the filter bed thickness. However, the different face velocities seem to affect only the collection of radon daughters. Optimum collection efficiencies for a clean bed of about 30% were found for respirable dust and radon daughters, and about 41>% for total dust, using an 8-in.-thick bed and a face velocity of 500 fpm. Dust build-up on the filter bed during operation led to an increase in collection efficiency, reaching 40 to 60% after two weeks."

Jan 1, 1973

By Francis Chartrand

The Kwyjibo deposit is an iron oxide Cu-REE-F-Mo-Au mineralization of Mesoproterozoic age located in the Grenville Province approximately 120 km NE of Sept-Îles, Quebec (Figure 1). Occurring along the SE margin of the Canatiche granitic complex, the deposit is composed of several polymetallic showings that are related to different textural facies of magnetite. The mineralization process at Kwyjibo is complex, and is divided into Early Granitophile, Magnetite, Main Polymetallic and Specular Hematite stages (Cayer et al., submitted for publication). The Main Polymetallic stage, comprising chalcopyrite, pyrite, fluorite, molybdenite and REE-bearing minerals, is superimposed on pre-existing magnetiterich rocks. Discovered by SOQUEM Inc. in 1993, the Kwyjibo deposit shares many characteristics with other hydrothermal polymetallic iron oxide deposits around the world. Foose and McLelland (1995) suggested that this class of mineralization could occur in the Grenville Province. However, only a few polymetallic occurrences are known to be associated with low-Ti iron oxide deposits in the Grenville. Kwyjibo is one of the most significant examples of a polymetallic iron oxide deposit to have been found in the Grenville Province to-date.

May 1, 2003

By A. M. Childs, R. F. Mather, K. R. Rawling

"The challenges encountered in the design and construction of mines and their process facilities today are becoming more intense and the engineering more competitive. The need to incorporate new techno1ogy to compensate for ever rising costs is always present, but its application in the harsh environment of Northern Canada increasingly requires the inclusion of new proven methods and innovative approaches to arrive at economically attractive projects.This paper deals with the development of the process design for the Cullaton Lake Gold Mine in the Northwest Territories. Particular emphasis is given to the interaction of the imposed construction and testwork schedules, and their effect on certain process decisions.The challenge that faced the project team may be defined by the following factors:1. A schedule which required that metallurgical testing, engineering, and procurement and delivery of all equipment and construction supplies should be complete within a period of ten months.2. Transportation of all personnel, equipment and supplies to the site by airlift, as no road was available or affordable.3. A six week period when transportation to the site was impossible.4. The extremes of temperature beyond the tree line in the Northwest Territories.5. A complete lack of infrastructure in the area."

Jan 1, 1983

By D. P. Tripathy

A supply chain encompasses all the activities associated with the flow and transformation of goods from the raw materials stage(extraction), through to the end user. Supply chain management (SCM) is the integration of these activities through improved supply chain relationship, to achieve a sustainable competitive advantage and it rests on its ability to provide the right goods and services when and where needed. The supply chain is the vital component of any company?s value chain which links the operating processes to its supplier and customer. The globalization of business promises to offer new and unique challenges for the supply chain competencies of most firms. Challenges will also increase in the environmental aspects of supply chain often referred to as ?Green Issues?. The supply chain of mining industry comprises of the flow of material and information from the mine site, to processing and loading for transport, to the customer. However, due to recent changing environmental requirements affecting mining and mineral processing operations, increasing attention is given to developing environmental management (EM) strategies for the mineral supply chain. This paper focuses on: ? Environmental factors leading to the development of an extended environmental supply chain, ? Additional challenges presented by the extension, ? Performance measures appropriate for the extended supply chain, ? Developing a general procedure towards achieving and maintaining the green supply chain.

May 1, 2006

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By D. Linzey

"History of Whitehorse Copper BeltThe first discovery of copper on the Whitehorse Copper Belt is reported to have been made by miners on their way to the Klondike in 1897. By 1899 the district had been well prospected and many of the presently known deposits had been staked.The first shipment of ore was from the Copper King property in 1900. This consisted of 9 tons of hand picked ore grading 46.4% copper. It was not until the period between 1912 and 1917, the production years of the Pueblo Mine, that significant ore shipments were made. Total production was 140,000 tons at 3.5% copper. An underground disaster killed six men and closed the mine in March 1917.Although the general area was dormant until after World War II, by 1947 geological mapping, magnetic surveys and diamond drilling had been done on the important showings. In 1954 Mr. Aubrey Simmonds directed the formation of Imperial Mines and Metals, which acquired by option and staking a large part of the Whitehorse Copper Belt. In 1957 Mr. Arnold Pitt reorganized the company as New Imperial Mines. With financing from Sumitomo and Toronto-Dominion Bank, a mill was built and production was started from the Little chief orebody by open pit in 1967."

Jan 1, 1977

By Y. Faitakis

In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production. It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About one-third of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations: The first generation (1940?1950): A ?fix it when it broke? attitude prevailed during that time, mostly because the industry was not highly automated. The second generation (1950?1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly. The third generation (1980?): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex, multi-functional teams become responsible for maintenance. At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance.

Jan 1, 2004

By Y. Faitakis, G. J. Powley, C. Mackenzie

"In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production.It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About onethird of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations:The first generation (1940–1950): A “fix it when it broke” attitude prevailed during that time, mostly because the industry was not highly automated.The second generation (1950–1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly.The third generation (1980–): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex multi-functional teams become responsible for maintenance.At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance."

Jan 1, 2004

By M. Massinaei, M. R. Yarahmadi, S. Zeidabadi, M. Oliazadeh

"Although the majority of new flotation column installations continue to be for cleaning or recleaning, an increasing number of flotation projects are specifying columns for roughing or scavenging duties. NICICO has recently installed flotation columns operating in rougher, cleaner and re-cleaner circuits at three new copper concentrators; Miduk, Sungun and Sarcheshmeh. Miduk is probably one of the unique operations that use flotation columns in a rougher circuit. The Miduk rougher circuit comprises five CISA parallel columns. The rougher concentrate constitutes 88% of final concentrate and reports to concentrate thickener. The rougher tailings are scavenged with ten 50 m3 mechanical cells. The scavenger concentrate is then reground and cleaned in three 3.2 m columns in parallel. The cleaner tailings are scavenged in six 50 m37mechanical cells. The cleaner tailings along with the rougher scavenger constitute final tailings.In Sarcheshmeh, the cleaner concentrate is re-cleaned in a column. The column tailings are sent back to the cleaning circuit and the concentrate is reported to the concentrate thickener.This paper reviews performance details of the flotation columns utilized in rougher circuits at Miduk and compares their metallurgical performances in an industrial scale with columns at cleaning circuits for copper flotation. Practical limitations for applying the flotation columns in rougher circuits will be discussed in details.INTRODUCTIONThe use of flotation columns has grown rapidly since the first successful commercial application at Mines Gaspe, where columns were used in a cleaning circuit to float molybdenite. Early applications of columns were restricted to replacing or adding final cleaning stages in existing circuits. Columns can achieve superior cleaning as compared to conventional cells due to their ability to support a large froth depth and the use of water for washing froth. Wash water travels down through the froth and crosses the pulp/froth interface, replaces the entrained particles reporting to the froth from pulp and improve the concentrate grade."

Jan 1, 2011

By P. T. O'Kane

"INTRODUCTION Wright Engineers Limited is active and has extensive experience in the design of pressure oxidation plants for the treatment of refractory gold ore and concentrate. In addition to the Mercur oxidation facility, similar projects undertaken during the last few years include the 3000 ton per day acid oxidation plant for the Getchell Mine, Nevada, a concentrate treatment autoclave for Asamera in 1984 and a feasibility study of a 50-tons per day autoclave plant for Consolidated Professor's Duport property in Ontario. The Equity Silver antimony and arsenic precipitation autoclaves, and the low pressure autoclaves at Key Lake Uranium in Northern Saskatchewan were also engineered by Wright in recent years.In August 1986, Wright was retained by Barrick Resources (U.S.A.) Inc. to add a 750 tpd pressure oxidation circuit to the existing mill at their Mercur Gold Mine, Utah. This paper describes this facility and outlines the start up in the spring of 1988 and subsequent successful operation. MERCUR OPERATION The Barrick Mercur Gold Mine is located at the south end of the Oquirrh Mountains in Tooele County, Utah. The carbon-in-leach (CIL) process plant camnenced operation in 1983 with a design throughput of 3000 tpd and has since been expanded to handle rrore than 5000 tpd. 'IWo ore types are mined, an oxide ore and a refractory ore, which is by Barrick's definition ""an ore from which less than 60% gold extraction is achieved by a standard CIL amenability test."" Typical of many sulphidic/carbonaceous ores, the refractory gold does not respond well to the cyanidation process. As a result, refractory ore has been stockpiled since the start of mining. As of June 1987, Mercur had about 570,000 tons of refractory ore stockpiled and 5.7 million tons of proven and probable reserves, grading 0.06 oz/t including approximately 3.5 million tons of tailings from the previous operation grading 0.55 oz/t. In 1986, Barrick decided to build a 750 ton per day pressure oxidation plant to process these ores. The process, for which a patent was granted, comprises pressure oxidation of the sulphides in an alkaline environment. It was developed in 1981 but was set aside in preference of a CIL plant treating only oxide ores by the previous owner of the property, Getty Oil. This process is capable of increasing gold recovery from the refractory ore from as low as 35% by conventional CIL processing to more than 85%. In 1986 Wright Engineers was engaged to undertake a feasibility study based on batch testing. This lead to a decision by Barrick Mercur later that year to build the commercial pressure oxidation plant. Wright was awarded the contract for engineering, procurement, construction managernent and commissioning in March 1987. The plant was mechanically complete in January 28, 1988, and was in operation by February 1988."

Jan 1, 1989

By Steve Wilkinson

"""Techniques for coarse-particle beneficiation of some gold ores and methods for determining potential for sorting any gold ore deposit.""With the advent of high speed computers, laser technology end different types of electronic sensing devices, ore sorting machinery has been developed, capable of handling significant tonnage rates while maintaining high level efficiency. Gold ores may be amenable to coarse-particle beneficiation where there exist measurable criteria upon which there can be recognition of auriferous versus barren lumps in the run of mine. Three types of criteria are suitable for sorting and are:i) Photometric - optical variance between ore and waste such as vein ores hosted by barren country rock;ii) Conductivity/Magnetic - based upon the metallic mineral content of ore end waste, and its association with Au, such as found in sulphide/arsenide Au ores,iii) Radtometric - detection of natural gamma activity occurring with uranium-bearirig gold ores.The method for determining the sortability of an ore depositconsists of, at least, three stages:i) Initial stage identification of ore and waste types,mineralogical/petrographical associations,amount of dilution in P.O.M.establishment of any sorting criteria]"

Jan 1, 1985

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988