Search Documents

By John H. McKillop

Industrial minerals production in Newfoundland in--creased in gross value by a total of 175 per cent during the ten-year period from 1954 to 1964. The Province accounts for all of ?Canada's fluorspar production and contains one of the most important fluorspar districts in North America. It is also the only producer of pyrophyllite in Canada, and quite recently has become an important producer of asbestos fibre. Limestone, gypsum, brick shale, sand and gravel also ?Contribute appreciably to the expanding industrial minerals phase of the Province's rapidly growing mining industry. Geological diversity characterizes Newfoundland's industrial minerals: Pyrophyllite deposits were formed by contact metamorphism of predominantly volcanic Proterozoic rocks. Fluorspar deposits are fissure-filling veins having the characteristics of typical epithermal deposits. Chrysotile asbestos production comes from one of the Island's serpentinized ultrabasic belts. Limestone is produced at three localities; two of them in the extensive carbonate rocks of the west coast. Gypsum production comes from a thick evaporite (gypsum and anhydrite) sequence in the Carboniferous rocks of the St. George's Bay area. Introduction

Jan 1, 1965

By Lawrence Devon Smith

"The Management and Economics Society has undertaken a survey of industry practice in the evaluation of mineral projects. The survey addresses a number of issues relating to evaluation techniques, discounted cash flow methodology, and risk. Completed during the spring and summer of2005, the results provide a record of opinion at an active and vital time in our industry.The 2005 survey questionnaire was distributed by e-mail to groups and organizations around the world. There were 22 respondents out of several hundred questionnaires distributed (we gather this small proportion of respondents is typical for such surveys). The responses, although a small number, show a consistency that suggests that the survey has captured the views of the industry. The results of the survey are summarized below in series of tables and graphs.The reader is cautioned that the results are a snapshot of industry practice at a point in time as represented by a small sampling of the industry's practitioners. These results should be viewed as indicative values."

Jan 1, 2003

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By S. Ivanova

The results presented in this paper show that the gold solution dilution is a key parameter to control the dispersion of gold on ?-Al2O3 the selected support. The variation of concentration leads to changes in pH which modify the nature of gold complexes from HAuCl4 formed in the solution. These complexes are presented. Some of them (AuCl3(OH)- and AuCl2(OH)2 -) react with the surface of alumina and give interesting interaction. AuCl2(OH)2 complex has been considered as an ideal complex because of the strong anchorage of a bidentate species on the alumina. This complex is formed mainly in a solution of gold with a concentration of 10-4 M giving a pH of 3.5-4.5. The nature of the anchorage and the amount of chlorine, has an influence upon the formation of Au-Cl bridges which modify the dispersion of the gold on alumina of the final catalyst as shown by TEM.

Oct 1, 2003

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By W. E. Cockfield

"The Stump Lake mining camp is in Nicola mining division of southern British Columbia. It lies about halfway between the cities of Kamloops and Merritt.The deposits at Stump Lake are among the earliest lode discoveries of British Columbia, many of the claims having been staked between 1882 and 1885. A considerable amount of work was done prior to 189Cl, after which very little was done until 1916. Since that time mining has been carried on at intervals, much of it on the same deposits, by a number of companies, including the Donahue Mines Corporation, the Planet Mines and Reduction Company, the Nicola Mines and Metals Company, the Consolidated Nicola Goldfields, Limited, and others. According to the British Columbia Department of Mines, total production from the area has been: gold, 8,520 oz.; silver, 259,413 oz.; copper, 40,822 lb.; lead, 2,208,859 lb.; and zinc, 367,869 lb. Most of the production has come from the Enterprise vein and a branch of the Enterprrsethe King William vein."

Jan 1, 1954

By Tamas Kekesi, Gergo Rimaszeki, Tibor Kulcsar

The efficient purification of soldering waste material can be achieved in a single operational step by the electrolytic refining in pure hydrochloric acid - tin-chloride media. The complex formation of the ionic species may offer a beneficial level of natural inhibition. Using the PCR (periodic current reversal) technology, is efficient in affecting the morphology of the cathodic deposit. In order to optimize the process, the investigation of the solution stability and the electrode reactions is essential. The natural tendency of the Sn(II) oxidation and precipitation can be overcome by properly controlling the concentration of the main components and the ratio of Sn(IV)/Sn(II) in the electrolyte solution. Polarization curves were obtained for different concentrations tin and hydrochloric acid. Conclusions referring to the electrode reaction were derived from the overvoltage - current plots. The morphology of the deposit can be correlated with the exchange current density, also determined from the polarization curves. The cathodic current efficiency and the morphology of deposited metal are affected by the distribution of tin species and the principal electrolysis parameters.

Jan 1, 2011

By W. H. Hastings

Introductory In the amount of her coal reserves, Saskatchewan ranks third among the provinces of the Dominion, with a total, as estimated by D. B. Dowling, of 59,812,000,000 tons. All the coal so far discovered in the Province is lignite, and it would appear unlikely that bituminous or higher grade coals exist. General Occurrence of the Coal The location of the coal-bearing formations in Saskatchewan is shown on the accompanying map. It will be seen that the areas lie principally in the southern part of the Province. The more darkly shaded areas indicate locations where development is taking place, or where coal-seams are known to occur, either through outcrops in valley-sides or through having been encountered during boring operations. The coal-seams are not necessarily continuous throughout the shaded areas, but in all pans of these there are coal possibilities. It is quite possible that small outliers of the coal-bearing formations may occur further north in the Province, but, generally speaking, coal is not likely to be found outside the shaded areas.

Jan 1, 1929

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By I. Takahashi

Recently, electronic devices have become smaller for some kinds of electronic devices, thermal dissipation and electrical conductivity of conventional Fe based alloy becomes insufficient. We selected the Cu-Fe based alloy CDA19400 and optimized the wire manufacturing process. Precipitates during aging treatment were observed by TEM. The size and distribution of the precipitates varied according to solution treatment temperature. With solution treatment at 950°C, the precipitates of y-Fe as fine as 10 nm were distributed dense in the copper matrix with coherency. For the solution treatment at 750°C, y-Fe of approximately 200 nm was observed. Comparing heat resistance of drawn wires, the material at 950°C treatment was superior. Electrical conductivity decreased from 63% IACS upon aging to 29% IACS by drawing. It is considered as particular phenomena for wires where materials are drawn with high reduction ratio. By the optimized manufacturing process, we successfully developed a new wire that has superior in strength, thermal conductivity, electrical conductivity, heat resistance and repeated bendability.

Jan 1, 2007

By M. C. Bluteau, G. P. Demopoulos

Arsenic reports in the effluents of many non-ferrous metallurgical operations. The production of scorodite, a crystalline ferric arsenate, is considered as an attractive option for the fixation of arsenic from aqueous effluents. However, scorodite solubility and long-term stability in the pH region of interest for tailings disposal have not been thoroughly investigated. In this study the long-term stability of scorodite in the pH 5 to 9 region and the mechanism of scorodite dissolution were studied. Construction of eh-pH diagrams indicated that scorodite stability is highly dependant on the nature (stability) of co-existing iron-hydroxide/oxyhydroxide. It was also found that when scorodite dissolves, a ferrihydrite phase having very small particles size (nano-scale) forms and that the growth and crystallization of this material are delayed by the presence of arsenate even under accelerated (75°C) ageing conditions. Around neutral pH and ambiant temperature (22°C) scorodite seems to reach an equilibrium with ferrihydrite after 48 weeks yielding soluble arsenic concentrations < 5 ppm.

Jan 1, 2004

By K. Morikawa, K. Asano, J. Yoshitomi

The quality requirements for ladle shrouds have become stricter year by year to the pursuit of higher productivity and improved quality in the continuous casting of steel. The ladle shrouds must be sufficiently durable under severe conditions, such as operation without preheating and during several sequential castings. The consideration is that ceramic fibres, which have been applied in shrouds for thermal insulation during casting, could pose a risk to the worker&apos;s health. We realized materials for the ladle shrouds which show high strength and low elasticity. At the same time pursuing effective insulation, a coating which contains no fibres (Foaming Coat) has been developed, replacing the conventional one containing fibres. These materials are durable under conditions of repetitive use and consequently satisfy the customer&apos;s demands. The ladle shrouds which were improved in this way have achieved an excellent durable life in hot service of three times that of conventional ones. This paper reports the recent technological developments in ladle shrouds as well as their performance under hot operating conditions.

Jan 1, 2004

By J. Lu

The impact of acid treatment in agglomeration/acid curing on copper extraction and acid consumption was investigated with respect to acid dosage and moisture. Without the addition of water, no agglomeration occurred. At an acid dosage above 15 kg/t, the acid was not completely consumed during acid curing. With the addition of 6.2% water, the particles agglomerated together. Copper, iron, magnesium and manganese were dissolved as sulfates and enriched in the fine fraction of the ore. The copper extraction and net acid consumption increased with increasing acid dosage. The copper extraction for acid curing with the addition of 6.2% water was higher than that without the addition of water due to the improved permeability and the increase in the contact with acid-soluble copper. During acid curing, the reaction of sulfuric acid with muscovite, abite and nacrite mainly took place on the surface of the particles while the reaction of sulfuric acid with clinochlore occurred not only on the surface but also inside the particles.

Jan 1, 2007

By Douglas E. Wolfe, Jogender Singh, Robert Miller, Dong-Ming Zhu, Jeff Eldridge

This paper discusses microstructural changes produced by two novel approaches using electron beam physical vapor deposition (EB-PVD) in which periodic strain fields/microporosity was incorporated within the large columnar grains of Zr02- 8wt.%Y2O3 (8YSZ). The traditional columnar microstructure of partially stabilized zirconia has been slightly modified to produce a lower thermal conductive thermal barrier coating (TBC) by periodically interrupting the condensing vapor resulting in microstructural modifications with diffuse or sharp interfaces and morphological changes on the sub-micron scale without changing the composition of the TBC. These microstructural modifications resulted in a 20-30% reduction in the thermal conductivity, 28-56% increase in hemispherical reflectance, improved oxidation cyclic life (over 100%), and better strain tolerance as compared to standard ZrO2-8wt.%Y2O3 deposited on platinum-nickel-aluminide and CoNiCrA1Y bond-coated MAR-M-247 test samples. The TBC with tailored microstructures were examined by various techniques including scanning electron microscopy (SEM), x-ray diffraction (XRD), steady-state laser heat flux technique, and hemispherical reflectance.

Jan 1, 2004

By T. Cutard, E. Yeugo Fogaing, C. Gault, H. Marzagui, N. Prompt, M. Huger, C. Deteuf

This paper deals with studies made in the field of the French research network PROMETHEREF. Several refractory castables are considered in this program. In the present paper, one of these materials is considered, it is a low cement castable based on andalusite aggregates. A particular attention is paid to microstructural changes during the first heating and on their effects on the high temperature mechanical behavior. Microstructural evolutions have been characterized by the way of dilatometry, scanning electron microcopy and X-ray diffraction. In-situ observations by environmental scanning electron microscopy gave complementary results on these high temperature microstructural changes. They deal with microcrack formation, phase changes, crystallization, liquid phase formation and sintering. By propagation of ultrasonic waves, high temperature continuous measurements of the Young&apos;s modulus have been made. Results confirm the existence of microstructural changes and allow to quantify the Young&apos;s modulus variations all along specific thermal cycles. High temperature four point bending tests and room temperature tensile tests were made in the same temperature range. Behavior evolutions could be found and interpreted with the help of previously mentioned results.

Jan 1, 2004

By Lorna Ortiz-Soto

A series of titiania- and silica-supported Au, Pt and Pt-Au catalysts prepared through different synthetic routes have been investigated in terms of their structural properties, adsorption of CO, and catalytic activity for the selective catalytic reduction of NO by propylene and the oxidation of and CO. Catalysts prepared by incipient wetness impregnation from individual Pt and Au precursors, exhibited characteristics very similar to those of monometallic Pt catalysts. This behavior is consistent with a model in which the two metals remain segregated due to their miscibility gap, and only Pt participates in the adsorption of CO and the reactions under consideration. In contrast, catalysts prepared from a Pt2Au4(C=CtBu)8 organo-bimetallic cluster precursor exhibited different behavior both in terms of CO adsorption and their catalytic activity for the three reactions examined. The combination of the kinetic, spectroscopic and structural characterization data suggests that in this case Pt and Au remain intimately mixed in the form of Pt-Au bimetallic particles, and that the presence of Au modifies the behavior of Pt.

Oct 1, 2003

By T. I. Kunkel

The economic prosperity of many Canadian communities depends on resource extraction within the traditional territories of Indigenous people. The geographic sites where these resources are situated are also areas where these Indigenous people have sustained themselves for millennia through hunting, fishing, trapping, and gathering activities. These traditional activities provide not only sustenance, but also cultural and spiritual values, and the ability to transmit oral Indigenous cultures and customs from generation to generation. The multimillion dollar revenue mine project proposed within the Cariboo Chilcotin region of British Columbia is situated geographically in a location which has sustained the Tsilhqot?in people for millennia. However, this group of people have important social and cultural values nested within the traditional activities at this location. These values are typically not at the forefront of resource development. Using Indigenous research and grounded theory, this research paper briefly outlines Aboriginal values of the First Nations communities within the Cariboo Chilcotin region and some lessons learned from the Tsilhqot?in people during the environmental assessment of the mine proposal.

Aug 1, 2013