Search Documents

By John C. Loretto

"Answers to some of the problems ofRecovery and Metallurgical AccountingIn Gold and Silver Hydrometallurgical PlantsThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the Metallurgical Test work figures and secondly, the Metallurgical Accounting figures do not balance.The plant results not agreeing with testwork figures are mainly due to:a) The testwork samples were not representative of the eventual plantfeed;b) Misinterpretation or misunderstanding of testwork;c) Plant losses;d) Plant design not allowing testwork results to be achieved;e) Operating deficiencies.a} The testwork samples being dissimilar to the plant feed occurs on a very high proportion of projects. The effects of this can beccr.ie exaggerated because the upper levels of the mining company often regard the original testwork figures as sacred and therefore base their judgement of current plant performance on these figures.Frequently the test work samples represent only a minor part of the orebody or alternatively a single composite of the whole ore body is used for the testwork long before it has been determined that all of the potentially different ore zones behave in the same manner. These errors can be compensated for by repeating the ""testwork tests 11 on current plant feed on a routine basis and using these tests to determine whether or not the plant is operating satisfactorily."

Jan 1, 1982

By X. J. Luo, F. Zhang

"Metallurgical slag (MS) such as steel slag, copper slag is a renewable resource and its compressive strength exceeds 200MPa in general. Because pure metal slug can easily be mixed into MS, complex recycle system is necessary in order to realize MS’s recycling. Meanwhile, there is high equipment failure rate in conventional crushing system. New crushing systems with inertial cone crusher could solve this problem very well. Recovery rate of MS tailings requires that crushing product can’t contain too much oversize product, so the essential equipment include two crushers and one sieve in the traditional crushing system. The new crushing system which only includes two crushers can meet the requirement and simplify the crush process. Investment of crushing equipment and infrastructure can be cut down. Operating and maintenance costs can be obviously reduced due to the simple process, which also could achieve high energy saving and excellent economic efficiency.INTRODUCTIONMetallurgical Slag (MS) such as steel slag, copper slag is a typical industrial solid waste and it threatens our environment’s safe. Metallurgical enterprises must take action to settle these wastes in order to protect our environment. Because pure metal slug can easily be mixed into MS, its uniaxial compressive strength (UCS) will exceed 200Mpa. If crushing station employs traditional crushing equipment, equipment failure will be easily caused because of these pure metal slugs. Coarse crushing equipment usually adapts jaw crusher in traditional Crushing technology and rod mill will be utilized to finish the secondary and fine crushing works. And the same time screening machinery should be used to ensure the suitable particle size (Figure 1)."

Jan 1, 2016

By B. Van den Bogaert, K. Binnemans, T. Van Gerven

Europium is one of the most critical rare-earth elements due to the limited supply of this element combined with a high demand for red lamp phosphors. Therefore, the recycling of europium from end-oflife lamp phosphors has become increasingly important. Photochemical reduction of europium(III) to europium(II) and subsequent removal from rare-earth mixtures by precipitation as EuSO4 is a very selective and efficient method to recover europium from binary europium/yttrium solutions. It is shown that full separation of europium and yttrium is feasible from laboratory prepared non-equimolar Eu/Y mixtures up to a ratio of 1/20, which reflect the composition of red lamp phosphors. Optimal conditions were determined at pH 4 with isopropanol as a radical scavenger, which is a less harmful and toxic compound than the commonly used formic acid scavenger. Europium removal efficiencies of more than 95% were achieved, with a purity of 98.5% of the EuSO4 precipitate. The irradiance of the used light source, expressed in mW/cm2, has a large impact on the illumination time needed to remove europium from the solution. It is observed that higher irradiance results in a shorter induction time, i.e. a period during which virtually no europium is removed, and a faster removal rate once the induction time has passed. The photochemical separation technique was applied to recover europium from leached industrial red lamp phosphor (YOX) powder, with a Eu/Y ratio of 1/30. Europium recovery of 50% was reached with a purity of 96%, proving the feasibility of this method for the recycling of europium from end-of-life lamp phosphors.

Jan 1, 2016

By T. A. Apelt, B. J. Elliot

"In September 1993, the flash furnace at Kalgoorlie Nickel Smelter, KNS, was brought off line after almost 12 years of operation. This is a record campaign life for a flash furnace. The furnace was' totally rebuilt and the capacity of the plant increased from 540 000 tpo to 750 000 tpa of concentrate throughput. The throughput increase was' achieved through the construction of a 525 t/day oxygen plant and upgrading of various plant ancillaries. A number of significant design modifications were also built into the flash furnace and oxygen enrichment was implemented in the operation of the Peirce-Smith converters.This paper discusses the rebuilding of the flash furnace and design modifications made to furnace equipment and ancillary plant. Some preliminary post-startup operating data are presented.IntroductionIn September 1993, Campaign 6 of the flash furnace was concluded and the furnace brought off line for rebuilding. The campaign length was almost 12 years and set a new record for campaign length. Planning for the rebuild took place over the last five years of the campaign. A number of modifications to the design of the furnace and the ancillary plant were planned to coincide with the furnace rebuild. The furnace was rebuilt and recommissioned in 70 days. The increased plant capacity of 750000 tpa has been achieved by the construction of a 525 t/day oxygen plant and modifications made to ancillary plant which centred around increased p~ control, efficiency and hygiene. This paper examines the development and implementation of the modifications made to the furnace and ancillary plant. Preliminary post-shutdown performance data are presented."

Jan 1, 1995

By J. L. Chakravarty, S. K. Dutta, S. Banerjee, D. Putatunda

"General purpose uniprocessor systems used in control applications, however fast they may be, at a certain stage attain saturation, forcing the user or designer to consider other avenues for solving the problem. This paper gives a broad overview of multiprocessing with special reference to transputers. Virtually all aspects, from parallel systems real-time control to artificial intelligence (AI) and expert systems, have been highlighted. The application of transpurters in unilayer and multilayer control are discussed in detail, with specific attention to sensor integration. Two case studies describe at length the utilization of transputers. IntroductionIn conformance with the high level taxonomy of parallel computer architectures as given by Ralph Duncan(l) (an improvement to Flynn's classification, which maintains the essential elements of useful taxonomy based on instructions and data streams), the MlMD architectures are categorized into two groups: (I) shared memory, and (2) distributed memory type. While the shared memory multiprocessors are more popular than the message-passing multiprocessors because they can be programmed in a conventional sequential fashion, their aspect of the architecture creates a perfonnance bottleneck. In contrast, message-passing multiprocessors (MPM) suffer from no such limitation and can attain linear speed increases that are directly proportional to the number of processors put into use. The MPM implementation also has its own advantages and disadvantages. Because the performance of the system is heavily dependent on it, the interconnection strategy in a distributed memory MIMD machine is of paramount importance. The transputer(2.J), a multiprocessor node of the distributed memory type, is becoming very popular. The advantages offered by the transputer make its application in the mining and processing industries very promising."

Jan 1, 1994

By Tobias Riedel, Peter Ay, University of Applied Sciences, Bianka Bade, Nicole Pausch, Bernhard Gemende, Florian Logsch, Matthias Leiker, Satyanarayana Narra, Claudia Glaser

This study focusses on the production of micro-structured agglomerates with high porosity from iron (III)-hydroxide-containing materials as adsorbent. A fractal-like structure of the agglomerates was created through a two-stage agglomeration process. Developing porous structures was necessary to increase the adsorption capacity. Various materials were used for the agglomeration experiments: i) filter cake (dry matter content 23 to 27 wt.-%); ii) FerroSorp®DGµ, a product which is already being used commercially for various applications in water cleaning. These materials in the pristine state have different characteristics such as dry matter content and particle size distribution. The desired optimised agglomerates can be achieved with the help of additives or binders, respectively. Additionally, the agglomeration process parameters play a vital role. In order to produce agglomerates with high porosity, the process was carried out in two steps. Firstly, FerroSorp®DGµ (d90 < 30 µm) was agglomerated jointly with the aforementioned filter cake in an Eirich intensive mixer (particle size range 125 µm < d90 < 500 µm). The second agglomeration step post drying was carried out in a pelletisation disc or in an Eirich intensive mixer with the addition of polymeric binders (up to particle sizes ranging from 2 to 4 mm). Agglomerates were characterised both in short and long term loading tests using phosphate as model ion. Contact times were less than 10 min, similar to practical application in percolation columns, or more than 7 days, respectively. The results show that the agglomerates produced in the two-stage pelletisation process have more advantageous properties like better accessibility of the active sites obtained by specificly influencing the particle size distribution during the two-stage pelletisation process.

Jan 1, 2016

By Anthony McDonald, Dominic Verhelst

"Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) started up a zinc plant and smelter in late 1930, employing technology of that period. The zinc plant has since converted from a roast/leach operation to a two stage pressure leach operation to eliminate sulphur dioxide emissioms. The smelter, however, is still continuing with much of the original roaster/reverberatory furnace technology. This paper reviews the process flow of the copper smelter, with some comments on past and recent changes.Smelter FlowsheetPrior to July 1993, the HBM&S smelter operation consisted of seven areas, namely feed preparation, roasters, reverberatory furnace, converters, anode casting, fuming plant, and dust collection. A simplified smelter flowsheet is shown in Figure 1. The data for tonnage of materials moving through the circuit are presented in Tables I to 4, and are representative of the time period from July 1992 to June 1993. A change in the zinc plant technology in 1993 resulted in the elimination of a zinc-bearing sulphide leach residue from the smelter feed blend, thereby greatly reducing the zinc content of slag produced in the smelter. Consequently the fuming plant and ancillary equipment, such as the drying plant, were shut down. These areas will, however, be described. With the closure of the zinc fuming furnaces all the slag from the reverberatory furnace is now discarded to stockpile.The over-all smelter metal recoveries are 96% for Cu and rn.5010 for Au and Ag. Figures 2 and 4 indicate historical production numbers of copper, silver and gold, respectively. A review of the minor element distribution in the smelter can be found elsewhere."

Jan 1, 1994

By R. Pakalnis, H. Miller, Madill. T.

"This paper describes a methodical approach to the estimation of the orientation and the magnitude of in-situ stresses. The study was performed at the Ruttan Mine, Sherritt Gordon Mines Ltd. , a 6,000 T.P.D. underground operation, located in northern Manitoba, Canada. It involves an initial estimate to be made based upon: structural interpretation • virgin stress measurements conducted in other areas (world wide, regional)The verification of the prevailing stress regime was made by conducting CSIRO hollow inclusion(1) overcoring measurements. The current cost for a virgin stress determination is about $7000 per measurement(2) and the difficulty encountered in attaining a good reading is high. This paper will describe the analytical procedures employed at Ruttan in evaluating the in-situ stress magnitude and orientation based on three overcore tests. It is proposed to perform an additional six measurements in order to verify the following results:Vertical stress = av (MPa) = 0.027 by depth (m)Major principal stress = o! """" 2.5 xav (340°/-20°)*Intermediate principal stress = a2 - 1.2xav (070°/0°)Minor principal stress = a3 """" o.8xov (160°/-70°)IntroductionThe Ruttan Mine of Sherritt Gordon Mines Ltd., a 6,000 T.P.D. underground operation, is located in northern Manitoba, Canada (Fig. I). The Ruttan copper-zinc orebody is a multi-lensed, steeply dipping (70 degrees) en-echelon deposit. Individual lenses have a maximum strike length of 350 m with widths varying from 7 m to 61 m. The mining method is o pen stoping with delayed backfilling and extends from surface to 860 m below surface."

Jan 1, 1985

By M. P. Kat, R. J. Barclay

"In 1984, a provincial inquiry into ground control and emergency preparedness in Ontario mines was commissioned by the Minister of Labour for Ontario. One of the recommendations put forth by the committee conducting this inquiry was that the Ontario mining regulations be modified to address more effectively the assessment of mine design. Mining regulations now require that every mine in the province annually assess its design with respect to ground stability. Subsequently, the Ministry of Labour has embarked on a ground control audit program to gather as much information as possible about the ground control programs in place at Ontario mines. In 1988, 47 underground mines were audited. The audits are intended to provide an overview of the level of engineering effort that is devoted to ground control on a provincial basis, by identifying the type of geotechnical information that is collected by each mine and how this information is used for stability analysis purposes in rationalizing excavation and support system designs. Also, the audits serve as an indicator of the severity of ground stability problems at individual mines, and how these problems are dealt with.This paper consists of information that has been extracted from the first series of ground control audits that were conducted in 1988. Specifically, the paper describes the types of support systems that are used in Ontario mines. It also discusses the rationale for local ground support selection, and the quality control programs that are in place for assessing the performance of installed ground support. As well, the type of geotechnical information that is collected, and to what extent it is used for the purpose of designing ground support systems, is reviewed"

Jan 1, 1991

By R. J. McLeod

"A new backfill plant was constructed in 1966 adjacent to the mill of Giant Yellowknife Mines. The reasons for the addition were to increase the storage capacity for sand fill, provide facilities for mixing cement with the fill for mine stope floors and provide a system for pumping fill to B -3 raise, a horizontal distance of 4700 feet from the mill. At the same time it was hoped to increase the density of the fill pumped underground.The plant consists of two only steel storage tanks of approximately 400 tons capacity of sand fill each. They are 17 feet in diameter and have conical bottoms. The cylindrical section is 28 feet high and the conical section 14 feet high. Each tank is fitted with water nozzles around the conical sections to remove solids at the required density. The water pressure on the nozzles is 150 lbs per square inch. The cyclones used to produce the sand back fill are located on top of the storage tanks. Five model Dl0B Kreb cyclones are used for this purpose. The vortex finders are 2 1/ 4 inch and the apex 1 1/4 inch. The cement silo or storage tank is located in the same building. It is a steel tank 17 feet diameter by 41 feet high with a conical bottom. The silo holds 250 tons of bulk cement, which is unloaded by air from a bulk highway carrier using 12 to 15 lbs air pressure. The cement is conveyed to the top of the silo, a distance of 70 feet from the ground by 450 lbs. of air.The mixing tank is a rubber lined steel tank 14 feet in diameter by 14 feet high. It is equipped with a Lightning Mixer supplied by Greey Mixing Equipment Ltd. The mechanism is driven by a 40 HP motor. The lower shaft is unsupported and is equipped with two 36 inch diameter axial flow turbine type rubber covered impellers. The backfill is discharged from the storage tank into the mixing tank by a 5"" x 4"" SRL-C pump powered by a 20 HP motor. A level control in the mixing tank regulates the rate of discharge of this pump through a Grinnell-Saunders automatic control valve. The cement silo is situated at such a height above the mixing tank to allow for a Rota-Lock, a small hopper and a cement feeder. The feeder is an Omega gravimetric belt type dry feeder with a Sensogram controller. The capacity of the cement feeder is 20 tons of cement per hour. The cement and backfill are mixed in the mixing tank at whatever ratio is required for the mine stope floors."

Jan 1, 1968

By Francisco Tamargo

"This paper refers to a new process for the full recovery (above 98%) of zinc and other valuable metals (Pb, Ag, Au) accompanying zinc in its concentrates while iron is separated as a marketable product free of any harmful impurities and suitable for sale to the cement industry. The process has been especially designed to achieve the following goals: maximizing the recovery of zinc and those valuable metals that are present in most zinc concentrates (lead, silver, gold); allowing the recovery of other valuable metals such as indium or germanium that could be present in some zinc concentrates; avoiding or minimizing the need for residue disposal in safe areas as it is the common practice nowadays in the zinc industry. Finally, the process achieves the previously related goals at a competitive cost, in line with the existing more efficient operations while using conventional equipment working under atmospheric conditions. The new process can be easily implemented in those smelters using the jarosite or goethite processes as well as in those smelters using direct leaching as a part of the processing facilities. A study has already been conducted on the use of jarosite in the cement manufacturing process, in the raw mix preparation as well as for a set controller. It shows that use of clean jarosite in the manufacture of ordinary Portland cement can result in improved quality of the clinker. Jarosite showed compatibility to influence the burning characteristics of the cement raw mixes. The presence of SO3 bearing mineral phases such as natrojarosite showed the suitability of clean jarosite for use as a set controller in cement production.INTRODUCTION Iron is by far the most abundant impurity accompanying zinc in its concentrates, and consequently, iron residue disposal is a major environmental concern for many zinc smelters in the world. This is especially true during the last 30 years when environmental restrictions became more and more strict. Much research work has been carried out during the last 30 years to try to find a solution for this important issue, but with little success. Only the jarofix process represents a partial solution to this problem as jarofix is stored nearby the smelters with certain limitations as a non-contaminant residue. However, it does not avoid the need to dispose of an important amount of residues every year, representing an environmental liability. Meanwhile, the number of countries limiting or banning the disposal of iron residues generated by the zinc smelters is growing, so that the solution to this problem is becoming an urgent matter right now. At the same time, the lack of appropriate available land for iron disposal is also a major concern in many cases."

Jan 1, 2016

By P. Espinoza, I. Yutronic, J. Olivares

"Compañía Minera Doña Inés de Collahuasi&apos;s (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved.Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals.On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs.Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others."

Jan 1, 2012

By V. Prodanovic, M. Militzer

Production of advanced linepipe steels with strength levels of 685MPa (100ksi) and higher requires excellent control of runout table cooling to produce the desired final fine-grained microstructures, which may include acicular ferrite. Cooling is exerted on the runout table by applying water jets onto the hot surface of the strip and heat is removed from the steel by forced convective boiling. The associated boiling mechanisms are complex and include film, transition and nucleate boiling. A pilot-scale runout table test rig has been built to systematically study boiling heat transfer from a moving steel plate by employing industrial scale headers. Experiments were conducted using test plates moving at speeds between 0.3 m/s and 1.4 m/s. The plates were cooled down from 850°C to temperatures below saturation by a single water jet supplied through an industrial size circular nozzle. Based on these experiments heat fluxes were determined and further used to develop improved runout table cooling models.

Jan 1, 2005

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana&apos;s laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996

By S. Southall, F. McCaffrey, F. Stober, M. Darini

Electrode Columns are commonly used in electric furnaces to deliver current and regulate furnace power to the smelting or melting process. Hatch has developed an innovative patent-pending system for lowering ("slipping") and/or raising ("back-slipping") the electrodes through an electrode column, without requiring the release of any clamping devices. All clamping forces are applied by springs. Unlike systems employing hydraulically applied clamping forces, (e.g., water bladders) the spring system is failsafe. Its inherent simplicity virtually eliminates the need for maintenance. The Hatch system is particularly applicable to Soderberg electrodes, and comprises two axially movable slipping clamps and a stationary power clamp, each of which apply a distributed, radial clamping force to the electrode. The magnitudes of the slipping sleeves&apos; clamping forces and sequencing of their axial movements are selected such that the slipping clamps, in conjunction with the weight of the electrode, provide slipping or back slipping without release of any clamping force.

Jan 1, 2005

By G. V. Poropat

Roughness of a discontinuity may be an important factor influencing shear strength of the discontinuity. Traditionally, determining the roughness of a discontinuity surface and providing a numerical measure of the roughness has required considerable effort or specialised equipment. The development of new 3D imaging tools that are easy to use has provided effective fast and accurate means of creating 3D surface models from which roughness measurements can be readily obtained. These new techniques are versatile enabling a user to measure roughness along any desired profile and at any resolution up to the limit of the spatial subtense of a measurement on the discontinuity surface. This paper primarily reviews extensions to the use of 3D imaging that enable the measurement of roughness. Additionally we provide some examples of the measurements and examine some of the issues associated with extracting measures from the spatial data that will support estimation of shear strength.

May 1, 2009

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By D. P. Wilkinson

Flow field design is critical to determining fuel cell performance with respect to operating conditions. Flow fields are normally designed around their maximum power operating point with the goals of maximizing performance and minimizing pressure drop between the inlet and outlet of the flow field. At lower power pressure drop is reduced, and water management and reactant distribution issues can occur over the active area as well as issues with cell to cell reactant distribution in the fuel cell stack. Flow fields have fixed flow channel geometries and fixed active areas which determine the reactant flow characteristics over the operational range of the fuel cell. In this paper we discuss some of the benefits of a new approach of changing the flow field active area with changing operating conditions. Such benefits for future fuel cell designs could include improved cell performance and stability, improved cell to cell reactant distribution, reduced low current density failure modes, and overall system advantages.

Jan 1, 2005

By Joseph B. de Hart

Two papers recently published on the subject of mine ventilation: "The Theory of Ventilation," by Douglas Hay. and "The True Effect of Natural Ventilation in Deep Mines," by Robert Clive, form the first and second reports respectively of the committee on the Ventilation of Mines appointed by the Midland Institute of Mining Engineers. The purpose of the present paper is to draw attention to these two papers and the discussion thereon. The theory of ventilation as taught in our schools is based on Atkinson&apos;s formula, which is a variation of Chezy&apos;s formula for the flow of water in pipes. The formula depends on two assumptions : 1. That air is an incompressible fluid within the limits ordinarily encountered, and; 2. That the pressure required to produce ventilation varies as the square of the rate of flow. The Atkinson formula has been assumed to hold good over the entire range of conditions met with in mines.

Jan 1, 1924