Search Documents

By Eric D. Marks

Fatalities resulting from ground workers colliding with objects and construction equipment accounted for approximately 18% of the total construction fatalities experienced in 2010. Current injury and fatality measuring methods have proven to be inadequate due to their use of passive measures of safety rather than a more active approach, such as the use of leading indicator data (also called near misses) of hazardous proximity situations between ground workers and heavy equipment on construction sites. The objectives are to create and evaluate the effectiveness of a reliable algorithm for collecting and analyzing the resulting leading indicator data from hazardous proximity situations. Numerous experiments emulating typical interactions between workers-on-foot and heavy equipment are used to evaluate the proximity sensing and detection technology. Safety leading indicator data (also called near misses) generated by the proximity sensing and detection technology during the experimental trials are used to create and assess the resulting algorithm. Results from the experiments indicate that leading indicator data generated from these systems can be processed and analyzed to identify hazardous proximity situations and incidents on construction sites.

Aug 1, 2013

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By Charles W. Villiers

AS is well known, there are large and valuable deposits of coal in British Columbia, both on the mainland and on Vancouver island. These deposits are widely distributed over the Province. The chief sources of supply on the mainland are found in the Fernie and Princeton-Nicola districts and on Vancouver island in the Comox and Nanaimo districts. The coals range from a very high quality bituminous coal to lignite. On the Upper Skeena river there is said to be a very large deposit of anthracite or semi-anthracite, but this field has not been developed. Coal was first discovered in British Columbia on the north end of Vancouver island in the year 1835, but it was not until 1852 that coal mining was seriously undertaken by the Hudson's Bay Company at Nanaimo, where mining has been carried on continuously ever since that date. The production of coal in the Province continued to increase until the year 1910, when the annual output reached its peak at 3,100,000 tons and a total of 7,800 men were employed in the industry. Since 1910, the production has dropped steadily until, in 1934, only 1,347,000 tons of coal were produced and less than 3,000 men were employed. This continued decrease in production has in no way been caused by lack of coal reserves. It has been due entirely to curtailment of markets. I do not propose to discuss coal mining practice in British Columbia, where we have all sorts of mining conditions, including submarine mining. There is no lack of coal supplies for either industrial or domestic purposes, nor is there likely to be any shortage of coal in the Province for many generations. We have our mining troubles, which increase the cost of production, but there are no insuperable difficulties to prevent the extraction of a large and increasing supply of coal. Our main difficulty-in fact our only serious difficulty-is to find a market for our output, and we must consider means which can be evolved not only to conserve our existing markets but also to expand them, at any rate within the boundaries of Canada. I will therefore confine my remarks chiefly to the all-important factor of Markets for our coal.

Jan 1, 1936

By A. G. Pentland

MODELS of mines may be classified under three headings: (a) sheet models, (b) solid models, and (c) skeleton models. Sheet Models are made of sheets of glass, celluloid, or a transparent plastic material. The sheets are mounted in a frame which holds them in a parallel position, either horizontally or vertically. Mine plans are traced on the horizontal sheets; sections on the vertical sheets. The model may be illuminated by electric lights which are separated from the sheets by an opalescent screen. It is viewed from above or from the side in such a way that the plans or sections are superimposed. Sheet models are very useful for the illustration of mines with narrow, steep-dipping veins, but they do not give a satisfactory representation of a large mine with a flat-dipping vein. Large sheets of glass are difficult to handle and to support in a frame.? It is difficult to see through a considerable number of them. Solid Models are made of plaster, concrete, wood, or other material usually in the form of slabs in which the mine workings are indicated by properly dimensioned cavities in the model. The slabs are coloured to show the veins, country rock, faults, etc. The model is divided along selected sections in order to give access to the interior by the temporary removal of parts. Solid models may be used to illustrate large orebodies of the Sullivan type, but they are cumbersome because parts must be removed to study details of structure. Skeleton Models are ones in which the underground cavities are represented by metal, wood, plaster, or wax proportionately shaped and held in place by a frame. They illustrate the work which has been done but do not show the position of the veins, dykes, faults, etc., in the unworked parts. It is necessary to project by eye between workings in order to determine the location of these features. The essential difference between the skeleton model and the solid model is that the skeleton model represents the mine workings by solid forms and does not show the unworked parts of the vein, whereas the solid model shows the vein as a solid and the mine workings as cavities in it. The skeleton model lends itself well to the representation of a large mine with large stopes.

Jan 1, 1944

By J-F. Magnan, M-A. Thibault, R. Boulianne, C. Gauthier, J-P. Gagné, G. Dufour

During the production of aluminium in smelters, the anodes used in electrolysis cells have to be replaced frequently. Anode butts are usually placed on anode trays for transportation and cooling, a practice during which Hydrogen Fluoride (HF) is emitted in large quantities. Covers developed in 2000 by Alcoa Deschambault to fit on the anodes trays were implemented, resulting in significant reductions of HF emissions. However, the covers are expensive to maintain and use short-life consumable parts. In January 2004, STAS and Alcoa decided to develop a more efficient design of cover, with lower maintenance costs and no need for consumable materials (like soft cushions). This paper presents a summary of the work performed to develop the new design as well as a summary of the test results.

Jan 1, 2006

By D. McConchie

The use of Bauxsol? (physically and chemically modified alumina refinery residues) to treat acid rock drainage (ARD), and sulphidic waste rock and tailings, provides new options for managing some intractable environmental problems at both derelict and active mine sites. Treatment of ARD waters using the Bauxsol technology shows that the effectiveness of raw Bauxsol material can be enhanced by including modest amounts of selected industrial minerals or common chemical additives. The type and amount of additive required and the amount of the blend needed to treat the water depends on the initial composition of the water and the target water quality; for some ARD waters, optimum treatment may require one or more changes in the type or amount of additive used. Maximum treatment efficiency can be achieved only when a balance is maintained between the rate of trace metal binding and the rate of change in water pH; adding treatment reagents faster than can be accommodated by the reaction kinetics will not result in more rapid water treatment. This paper presents the results for treating several ARD waters to illustrate the importance of blend selection and treatment procedure. Although treating ARD water is often necessary, this strategy treats the symptoms rather than the cause. The best permanent solution is to treat the sulphidic waste rock or tailings such that they do not continue to oxidise and produce acidic metal-rich leachates; sulphide oxidation needs to be stopped or slowed to a rate that can be accommodated by normal environmental processes. Capping lined impoundments is not a solution because all caps and linings will inevitably fail some time in the future creating a nasty surprise for some future generation. Adding lime is also less than ideal because the lime leaches from the treated material; treatment often appears to be effective for a few years and then fails. Bauxsol technology offers effective alternatives to conventional liming and capping procedures and Bauxsol blend application rates and procedures can be planned to ensure that no acidic or metal-rich water can ever escape from the site. Bauxsol can be physically mixed with the sulphidic mine wastes or it can used to form subsurface permeable reactive barriers, or both. Bauxsol treated waste rock and tailings can be immediately and effectively revegetated. In this paper we present leachate quality and plant growth rate data for several sulphidic waste rock and tailings deposits treated using the new technology.

May 1, 2003

By H. C. L. Reemeyer

One of the fundamental trade-offs for copper concentrators is between grinding circuit product size and copper recovery. The capital and operating cost savings and throughput increases for a coarser grind should be evaluated against potential recovery reductions. Other benefits of coarser grinds, such as GHG emissions reductions and favourable effects on tailings and water management should also be considered. This paper assesses the formation of laboratory and pilot test programs, design of process flowsheets, equipment selection, and evaluation methods to determine the most appropriate and economical grind size for a given deposit. The paper will include an evaluation of case studies. INTRODUCTION The majority of the world’s mined copper comes from sulphide deposits, which are mostly processed using crushing, grinding, flotation and dewatering flowsheets to produce copper-bearing concentrates for smelting. Ores must be ground to a sufficiently fine size to achieve an acceptable level of liberation to allow both high recovery of copper and valuable by-product minerals while efficiently rejecting gangue to tailings. Therefore, a key design parameter in process plant design is the grind size of the flotation feed. Copper concentrators use a variety of grind size targets that depend on various factors, including ore mineralogy and the grain sizes of valuable and gangue minerals; the sensitivity of valuable mineral recoveries in the rougher flotation stages to grind size, ore hardness; electricity costs; and mining vs. processing throughput constraints. Typically, copper and by-product recovery increase as grind size is reduced, which can improve revenue, but finer grinds increase power and grinding media operating costs and may have implications for tailings management. This paper explores the trade-offs that should be assessed in determining the optimum grind size, and to answer the question if coarser grinds are worthwhile. METALLURGICAL AND FLOWSHEET FACTORS Recovery-by-size behaviour of sulphide-bearing particles In base metals sulphide flotation, it is typical that flotation recoveries vary by particle size. Metal sulphide particles rendered hydrophobic by collector in intermediate size ranges (e.g. 10 to 100 um) usually show very high recoveries, often approaching 100%. Recovery usually falls away in finer size fractions (<10 um) as fine particles have little inertia and can move around bubbles without colliding and attaching to them. Coarser particles (>100 um) are susceptible to particle-bubble detachment and dropback (Jameson, 2019).

Jan 1, 2019

By Chunlin Chen

Published data on thermodynamics of tin in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The developed model/database was applied in modelling the Sn deportment in primary copper smelting and e-waste melting processes. The results show that Sn can be removed from the matte through evaporation of various volatile Sn species (with SnS the most volatile) and slagging during copper smelting. The Sn removal increased with increasing matte grade due to the increased gas and slag volume. In the e-waste smelting process, fluxing strategy was developed for smelting e waste to produce a slag with reasonable liquidus and viscosity. Modelling results show that very low amounts of Sn reported to the gas phase due to low S, hence low SnS partial pressure in the system. The black copper produced could contain a few percent of Sn depending on the oxygen potential. The Sn in the black copper could be removed to the slag phase during anode refining. INTRODUCTION Tin is an impurity element commonly found in copper ores, which will be dispersed into various solid, liquid, and gaseous streams during the pyrometallurgical processing of copper. Tin alloy is widely used in electronic soldering due to its low melting point. The growth in treatment of recycled e-waste through primary and secondary copper smelting has led to an increased tin input to the smelting system. Therefore, the deportment of tin between phases is of great interest to the operators of modern smelters. Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems (Zhang et al., 2002). Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature system (Chen, Zhang, Wright, & Jahanshahi, 2006). In the present paper, the thermodynamic data on tin in liquid copper, matte and slag have been reviewed, assessed and used in the development of a database for Sn slag, alloy and matte phases. The model/database was applied in modelling the tin deportment in primary copper smelting and e-waste smelting processes. The aim of this study is to provide a better understanding of the chemical behaviours of tin in high-temperature copper processing and e-waste smelting.

Jan 1, 2019

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998

By L. Beiza, L. Velásquez-Yévenes

Chalcopyrite is by far the most abundant copper sulphide on Earth, but it has proved to be problematic in its processing by leaching, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface during leaching. This study is focussed on the electrochemistry of chalcopyrite dissolution in acidic chloride system, which has recently gained attention as a feasible alternative to conventional sulphate media for chalcopyrite leaching. It is well understood that chalcopyrite dissolution from mineral grains depends strongly on the solution redox potential at the mineral surface as well as the composition of the product layer that may form on its surface. The chloride ions in solution support the Cu(II)/Cu(I) couple as the primary oxidant, as they can form complexes with the cuprous ions formed, increasing the dissolution rate. Additionally, these ions increase the potential range where chalcopyrite can be oxidized. The chemical reaction that occurs on the surface of chalcopyrite in chloride solutions in the presence of cupric ions will be characterized and the coulometry of the reaction will be reported to understand what is happening on the surface of chalcopyrite. Electrochemical experiments have been carried out to investigate the behaviour of mixed potential by open circuit potential (OCP) measurement for 30 minutes using sulphuric acid at pH 1 under nitrogen at 25⁰ C. The effect of chloride was analysed at 0, 20, 50 and 100 g/L and cupric ions from 0 to 50 g/L. The potentials obtained were then used to carry out chronoamperometry tests for a period of 30 minutes in absence of cupric ions. The mixed potential did not show a significant difference with an increase in cupric concentrations in the absence of chloride. Increased mixed potentials and current densities were observed at higher chloride and cupric concentrations. Chronoamperometry tests at those potentials were used to construct a voltammogram trace which has the same trend as a normal cyclic voltammogram but with much lower current densities. INTRODUCTION As a result of the depletion of copper oxides, the leaching of copper sulphide minerals has become the focus of many studies. Chalcopyrite, (CuFeS2) which is the most abundant of copper minerals, has proved to be challenging to process via hydrometallurgy, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface, during leaching.

Jan 1, 2019

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By A. R. MacPherson

"This paper considers four aspects of autogenous grinding. Part 1 discusses statements on power efficiency of autogenous grinding compared to conventional crushing and grinding systems. It also demonstrates how high-power efficiency can be obtained from autogenous grinding systems. Part 2 considers a simple method of testing ores to determine the type of autogenous plant which can treat these ores on a commercial basis. A comparison of testing for simple small plants vs large plants or complex ores is included. Part 3 considers important aspects which have to be considered in proper design of an autogenous grinding system. Part 4 discusses problem ores and how they can be treated in an autogenous system. INTRODUCTIONAfter about 35 years of using autogenous grinding plants in the mining industry, it is perhaps time to review where we are with this, by now, relatively old development. Autogenous grinding in this paper means grinding run-of-mine ore by fully autogenous means or by using a ball charge to assist the grinding (semi-autogenous). Also, autogenous grinding can be eitherby dry or wet.The use of autogenous grinding in the fifties was making its slow start, and it was not until the sixties that more of the mining industry would consider its use . By the seventies, most builders of new plants would have considered autogenous grinding, whether they used it or not, in the final design.In the eighties, most large plants use autogenous mills and to reduce over-all operating costs, many older conventional plants are now looking and actually retrofitting these old plants with autogenous grinding mills.It is evident that many misconceptions concerning autogenous grinding are still current. Some come from improperly designed plants which result from poor test work. There are many considerations in the proper design of autogenous plants. Some ores have been found to give problems even in a well designed plant. These ore types are beginning to be classified and recognition in the test stage allows steps to be taken in the design so that these ores can be efficiently handled in autogenous grinding plants.Therefore, this paper will address the following aspects of autogenous grinding:1. Misconceptions regarding autogenous grinding.2. Testing of ores to ensure a well designed commercial plant.3. Important considerations in mill design.4. Difficult ores, their recognition and types of design to handle such ores."

Jan 1, 1989

The following briefing is intended to provide an overview of the present and future challenges associated with our access to a secure and adequate supply of electrical energy necessary to support safe, productive and sustainable mining initiatives at Musselwhite. Contents ??Site power demand vs. current available supply ??Supply technical deficiencies ?adequacy and security of present supply ??Present internal generation ??Anticipated future internal generation requirements ??Increased requirements necessary for planned expansion ?demand/security ??Goldcorp?s strategy to achieve required supply ?transmission line initiative ??Subsequent benefits to others from the Goldcorp initiative. ??Economic impact of MusselwhiteMine on the northwest region ??Anticipated economic impact of planned expansion ??Expected life cycle of MusselwhiteMine ??Comparative energy costs for similar operations in other jurisdictions ??Conclusions ??Anticipated action plan ??Energy Management Initiatives ??Site Orientation

May 1, 2009

Over the years, efficient on-line monitoring of performance and status of an electrolytic copper refining process has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Recent innovative developments by Kennecott Utah Copper Corporation and Outokumpu Technology in wireless cell voltage and individual cell temperature sensing opens new possibilities to improve and modernize tank house management. This paper describes the powerful Outokumpu CellSenseTM refinery monitoring system for efficient interpretation of data produced by wireless CellSensorTM system with traditional refinery measurements. Examples from commercial tank house installations demonstrate the benefits of the system to improved process control and operation. The Outokumpu CellSenseTM monitoring system is simple to operate and accessible to all the plant operation teams.

Jan 1, 2007

By T. Ediz

Sarkuysan Electrolytic Copper holds three competitive technologies namely Outokumpu, Southwire (SCR®) and CONTIROD® under the same roof. After more then thirty years experience of Outokumpu Upcast ® in producing oxygen free wire- rod, and twenty years of SCR® experience, in 1999 it was decided to introduce the CONTIROD® process to the customers with a chance and advantage to test capabilities of each process in order to fulfil their requirements, expectations, and turn this know-how to their benefit. After reviewing the milestones of Sarkuysan&apos;s evolution in Turkey as global wire-rod producer, this paper will briefly present the modernization and expansion activities in the CONTIROD® plant consisting of the different phases following the first start-up, and the results of these activities. It will highlight the gains and improvements of some operational parameters within this period.

Jan 1, 2007

By W. M. Silva, Bittencourt. L. R. M.

Three newly developed alumino-silicate refractory bricks for use in safety lining of aluminum electrolysis cells were compared to one commonly used bricks for the same application. It was shown that the increase in silica content and decrease in permeability led to a sensitive decrease in cryolite attack. Both parameters are of utmost importance in selecting bricks for these cells. The reasons for this observation were the formation of a more viscous liquid after the reaction between molten cryolite and the brick, and the reduction of the rate of penetration. Moreover, a novel mortar with high silica content was tested and has shown improved resistance to molten cryolite. The use of oxidizing atmosphere led to increased attack rate in the brick when compared to reducing condition. The opposite effect was observed in the mortars.

Jan 1, 2004

By Joseph J. Poveromo

The blast furnace today continues as the primary production method of hot metal in large-scale steel production. The blast furnace process has been the target of repeated attempts to replace it with various process options, including direct reduction and coke-free smelting reduction. While these new technologies are being adopted in appropriate niches, the blast furnace has responded to the challenge by being amenable to continuous improvement. I will review the role of the blast furnace, major developmental and improvement trends, and then list the current important issues in ironmaking. I will outline the challenges to be faced by the blast furnace to maintain its position as the primary hot metal production process. The material presented here is an update of earlier presentations made in Stockholm, Sweden, 1996, Duluth, 1998 and Chicago, 2000.

May 1, 2003

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant’s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today’s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user’s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project’s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By Chih-Huey Lin

The Au/?-Al2O3 catalyst prepared by AuCl3 impregnation is subjected to the influence of residual chlorine after an oven drying. A post-impregnation NH4OH treatment was able to eliminate chlorine, and to reduce the cluster size of Au moiety. However, the CO oxidation activity was not increased by this post-impregnation NH4OH treatment. This suggests that certain metal-support interaction (MSI) is the determining factor for the activity of Au catalysts. Thermal treatment under H2, O2 or He was attempted to increase MSI of the prepared catalyst with or without the post-impregnation NH4OH treatment. No significant activity enhancement was found but the TPD analysis suggests that a H2 treatment has a higher chance to induce MSI.

Oct 1, 2003

By Seongki Lee

The purpose of this paper is to propose the real-time facility management system framework based on Building Information Model (BIM) and Web of Things. Latest IT such as BIM is rapidly spreading to architecture, civil engineering, engineering and maintenance with the aim of simplifying complex system in buildings and facilities, minimizing operation cost, providing high value services and advancing facility management. In particular, BIM-based management framework design to assist the development of sensor information operation system, which adds convenience to facility maintenance and management, has emerged as a key issue. To this end, this paper proposed conceptual framework for data warehouse, web service and interface that make up real-time facility management system. The paper also produced conceptual methodology on CoRE-based web service platform, mobile device, BIM and WSN mapping.

Aug 1, 2013