Search Documents

By L. S. Brooks

TIMBER HANDLING presents a problem for any mine where appreciable amounts are used. This problem is accentuated where the shaft compartments are too small to allow a loaded timber truck to be lowered in the mine cage. When Normetal Mining Corporation, Limited, found it necessary to resort to square-set mining it faced this problem of getting large quantities of timber down a shaft that was also required for hoisting ore. A 'timber car' that could be suspended under the cage was developed to overcome this difficulty. Production started at the Normetal mine in 1937, at the rate of 250 tons per day. In 1938 a winze, known as No. 3 shaft, was sunk from the 800-foot level ?to the 1,385-foot level. This was later raised to surface and then deepened to 3,275 feet in three stages and became the main production shaft. The portion of the mine below the 3,070-foot level is serviced by a winze, locally referred to as No. 4 shaft, which has been developed for stoping down to the 3,990-foot level and which has been deepened to the 5,365-foot level. No. 3 shaft has two hoisting compartments, each 4 ft. 6 in. by 5 ft. 0 in. inside the timbers, through which the ?ore must be hoisted and timber and supplies lowered.

Jan 1, 1956

By Rene Klymowsky, Norbert Patzelt, Egbert Burchardt, Johann Knecht

"The challenge of ""ore bodies getting steadily harder and lower in grade"" was brought to light during the first oil crisis in the 70's. Shortly afterwards, HPGRs appeared on the scene with the promise of saving energy. This combined with developments in wear protection for the rolls ushered in a period of trade-off studies that considered the HPGR as an option to improve project economics or to even make projects feasible at all.Since then, applications of HPGRs at Cerro Verde (Freeport), PTFI Grasberg (Freeport), Mogalakwena (Anglo Platinum), Tarkwa (Goldfields), Boddington (Newmont), Penasquito (Goldcorp), and others have contributed to the creation of a formidable basket of operating experience. Collected through years of successful operation, this information has been used to validate design criteria, scale-up factors and establishing a clearer picture of what ""to do"" and what ""not to do"".This paper compares results from various mining operations using HPGRs in their processing plants. Some of the lessons learnt in different operating environments are reviewed in order to support proper implementation and operation of HPGR's. Some of the development programs that have been initiated to improve wear life of the tyres and to reduce overall operating costs are reviewed. It is timely to summarize today’s experience and analyse its implications for existing and new operations"

Jan 1, 2012

By G. E. Rodger, R. Jugoon

"SUMMARYSamples of Aunor gold precipitates which varied widely in gold content were fluxed to produce a bisilicate slag with various oxidizers and combinations of oxidizers. On the basis of some preliminary tests a flux composition was chosen which appeared to show the most promise.The different components of this flux were then incorporated into a matrix for a 23 factorial design experiment to determine what were the most important variables and what changes should be made to the flux composition to optimize the resultant total bullion fineness.The results of the 23 factorial design experiment showed that the flux composition as calculated was very close to an optimum as only very minor changes were required to give bullion in excess of 995 fine.INTRODUCTIONEarly in 1969 the results from the Aunor Gold Mines refinery showed that wide variations existed both in precipitate grade and in total bullion fineness. An analysis of this data showed that as the precipitate grade increased, the gold bullion fineness also increased (see appendix 1). Therefore, to improve the refinery results test work was initiated to: 1) improve the precipitate grade and 2) to determine, with the help of statistics, a flux composition which would be able to handle wide variations in precipitate grade and give a total bullion fineness in excess of 950 fine."

Jan 1, 1970

By E. J. Marcotte

"BRIEF DESCRIPTION OF GRINDING CIRCUITCrushed ore at -5/ 16 in. is delivered by a conveyor system from the crushing plant to two 1250 ton fine ore bins. The ore is transferred from each bin by a 30 in. feeder conveyor belt, operated by a Link Belt P.I. V. (variable speed) drive, to a 24 in. conveyor that feeds the 8 x 10 Allis Chalmers rod mill.The rod mill discharges to a common mill discharge pump box. Three 6 x 6 SRL pumps are employed to pump the combined mill discharge pulp to a common distributor box which distributes the feed to two of the three Kreb D lSB cyclones in each of the two banks at a hydraulic pressure of 6 psi.The cyclone overflow at a specific gravity of 1. 25 (i.e. 32% solids) is transferred by gravity to two revolving chip screens for wood chip removal and from there to a pump box. Two 5 x 5 SRL pumps feed the pulp to the thickeners. The underflow from the cyclones is fed to two 8 x 8 Allis Chalmers ball mills which discharge to the common mill discharge pump box. Thus, a closed circuit is formed between the ball mills and their respective bank of cyclones. The circulating load as most recently calculated is 262%."

Jan 1, 1966

By A. M. Reyes

Flow field hydrodynamics of serpentine flow channels was investigated numerically using computational fluid dynamics (CFD). The velocity profile simulated by the CFD model was evaluated with respect to experimental results from the literature. Rectangular and tapered flow channels were compared with respect to mixing and water management capabilities, and pressure drop. The CFD model was further developed to account for electrochemical reaction on the cathode side to determine which channel configuration was most effective in reactant conversion. The velocity profile differences between the channels were found to impact reactant conversion, as the rectangular channel had the highest conversion. With respect to water management, although the tapered channel was found to have a higher overall pressure drop, the rectangular channel was found to have higher shear and pressure forces acting on simulated liquid water droplets in the channel.

Jan 1, 2005

By C. Grisanti, E. Prina Howald

The major of Swiss territory is occupied by mountains. Natural events as floods, debris flows, landslides, rockfalls, and avalanches regularly threaten the safety of people and properties. On the one hand, extreme weather events cause great damages, on the other hand, the enhancement of territory’s exploitation increases the risk. The Swiss Government makes many efforts to deal with the prevention of natural hazards, especially through measures of land management. As stated by federal law, Swiss cantons are obliged to establish hazard maps and to take the risk into account in the land management. Hazard maps are based on the hazard matrix, whose abscissa and ordinate are probability and intensity of the event on site. This project focuses on rockfalls. It consists of three main parts: the creation of a database to collect data on site, the creation of a catalog with all type of measures, and the development of a methodology for the analysis of the effectiveness of protective measures. The creation of the database allows us to collect information: about the site, about protective structures implemented on it, and about failures. With many multiple choice fields and few free text fields, it can collect data in a homogeneous way, without redundancy. The catalog has to be a tool that gives a basis to make decisions. It collects information about all types of protective measures implemented on Canton Vaud’s territory or available on the Swiss market. Free text fields allow for data storage of specifics, to give a complete view of structure’s characteristics and potentials. Methodology consists of four steps. The core of the procedure is the structure’s evaluation following a score system; it allows for calculation of reduction factors that have to be applied to intensity and probability parameters of the structure. Then it is necessary to convert the reduced structure’s intensity value into a residual site’s intensity value. Although the first step enables us to choose suitable measure for a specific site, it is not necessary to perform it. Second step allows us to evaluate structures under scenario 0, where structures are in best conditions. Third step allows us to evaluate structures under six scenarios of possible failings. Fourth step allows us to convert structure’s reduced intensity into event’s residual intensity and to establish the new point on hazard matrix. While the procedure has already been defined, details of score system and conversion have to be developed during the second phase of the project.

Jan 1, 2015

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

By Ron Ferris

The Westinghouse Temptifier TM, using heat pump principles, recovers lowgrade waste heat in the 600P to 1600P temperature range and amplifies it to usable levels of up to 2200P. Coefficients of performance (C.P.D.) normally encountered are from 3.0 to 6.0, with capacities from 200,000 to 10 million Btu/hr.

Jan 1, 1979

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By Chris Carr

This paper describes the process employed and the work undertaken to enable the surrender of the mine permit relating to the two tailings deposits at the abandoned Red Mountain Mine site near Rossland, BC. The first phase of the work undertaken was to provide urgent remedial work for protection of the environment, primarily through rehabilitation or replacement of surface water drainage systems. The second phase was to up-grade the water management systems to the appropriate level given their consequences of failure. The final phase of work is to ensure long term geotechnical stability of the facilities to the same level of risk. Establishment of a sustaining fund will facilitate long term monitoring and maintenance of the facilities.

May 1, 2002

By R. Esteban, D. Runnels, S. Girgin, J. Torrealba-Vargas

"Each mineral processing project requires early testwork to evaluate the economic potential of a deposit. The testwork needs to be efficient and it should provide enough information to obtain key parameters, first for a high level flowsheet selection at the conceptual and PEA stages and then, for later stages, to confirm the flowsheet selection and optimize the metallurgical efficiency of the plant. The testwork should consider all rock types or lithologies present, and carry out testwork for the purpose of sizing the major processing equipment.A successful project requires that the project stakeholders develop an efficient sample collection program to produce enough material for a scoping and pre-feasibility level program. This involves the participation of a team of geologists, mining and metallurgical engineers in the project, as early as possible, to define the deposit characteristics that need to be validated.The project schedule requires a close control of the testwork scope, procedures, and timing, but also the efficient analysis of results to provide indications of red flags that could impact circuit design as early as possible.In some cases, projects are put on hold due to fluctuations of the world economy until the return of more favorable conditions. In that scenario, prior data analysis of former testwork results could reduce significantly the amount of testwork required to restart a project. The paper will also present examples where the analysis of former testwork data was used to reduce the amount of new testwork in addition to presenting examples of latest projects where the above-mentioned test program approach was followed."

Jan 1, 2016

By A. J. Rigby

Computer generated, actual-scale furnace models have been imported into a rendering software application to provide for impressively realistic surface features and lighting. When these models are imported into a 3D engine framework, it is possible to create content-rich virtual environments allowing for complete interactivity and could provide for a powerful tool to conceptualize refractory lining designs. This technology has been applied to illustrate the optimized design concept of an anode-refining vessel, which can be expected to be completely relined in six days and to last for 4-5 years with minimal partial relining. This technology could easily be applied to other smelter furnace, converter and refining vessel designs.

Jan 1, 2007

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company's business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010

By M-A. Thibault, C. Gauthierand, J-P. Gagné, J-Y. Carrier, P. Rochette, G. Dufour

"Anodes consumed in the electrolytic process for the production of primary aluminium are considered consumables. They need to be replaced at regular intervals of approximately one month. The so-called anode butts which are removed from the cells contain the metal supports (rods), cast iron thimbles, crust and residual carbon material. Cleaning is required to remove the waste material before the rods are fitted with new anodes. An inspection is required to ascertain if repairs to the rods are necessary. Presently, this inspection is carried out visually. ST AS, in 2004 in collaboration with Alcoa Deschambault, initiated a project to develop an automated inspection system. The objectives were to find a technical solution to perform these functions with a very simple system. Such a system was designed around ""artificial vision"". The inspection system developed uses only one fixed camera and does not require a separate step in the process for the anode rod assembly to perform the inspection. This paper presents the initial steps of the work performed to develop the equipment and software as well as a summary of the results obtained."

Jan 1, 2006

By S. Sundararajan, J. Brousseau, P. Bocher, M. Galopin, N. Barka

This research is committed to the prediction of the hardness profile produced by induction heating, using a computer-modeling software. The paper presents the simulation of the induction hardening process to analyse the sensitivity of the induction parameters on the hardness profile of a low alloy steel specimen. The developed numerical model includes the coupling effect between electromagnetic and thermal fields, and takes into account the non linear behaviour of the material properties. The study applies an enlightened experimentation method to build the feasible domain of the process and to achieve predictive empirical modeling. The ultimate goal is to replace the trial and error method that is usually used for the development of new parts, by costless experiments with the numerical model. Further development of this approach will lead to the computation of the residual stresses and finally to the assessment of the mechanical properties of the part. The end result will be the ability to shorten the development time and to improve the quality of the hardened part.

Jan 1, 2006

By M. Leijd, K. S. Forrester, M. Saxon, M. Oczlon

This paper provides an introduction to wet high intensity magnetic separation (WHIMS) and its successful application to the beneficiation of rare earth element (REE) enriched eudialyte. The analysis includes an in-depth reporting of the deportment of key elements as well as a statistical interpretation of the relative importance of operational parameters including magnetic field intensity, flow velocity, and matrix loading density. Conclusions are drawn on the relative success of the technology, potential areas for process improvement, and the research direction that continues to be investigated. Three original equipment manufacturer (OEM) technologies were subjected to a series of screening and characterization tests to identify the optimal operating parameter set to magnetically beneficiate eudialyte from Norra Kärr, Sweden. Upon the completion of the characterization test it was apparent that the Metso HGMS technology was superior with respect to REE recovery and gangue rejection for the Norra Kärr composite. The Metso HGMS was then subjected to a series of verification tests to confirm the repeatability and reproducibility of the system.

Jan 1, 2014

By G. W. Brooks

This short article is quite different to the general run of papers that are presented to the Institute, but no apology is offered because I consider that first-aid and mine-rescue work are of equal importance to many other subjects that are dealt with in our Transactions. Members of the Institute should be as much interested in the safety of persons engaged in the mining industry as they are in the practical methods of modern mining. We must not only do our best to conserve life and property by adopting every known device to that end, but we must also prepare ourselves so that we may take prompt and effective action when life is in danger, or when property is subject to loss. The need for such preparation in Alberta is perhaps greater than in most places where mining is carried on, and we must spare no effort to assemble at every mine men who are well trained in first-aid and mine-rescue work. The large area over which the mines are distributed renders central training stations out of the question, hence the need for local rescue-teams. Hospitals with skilled staffs, close enough to the mines to be convenient, also seem to be out of the question; therefore the greater need of a high standard of first-aid training for the people in our mining camps. The Government mine-rescue cars are supplied with the equipment necessary for training persons in this essential work and also for dealing with disasters should they occur. The question then arises: are there a sufficient number of men who are trained ? If so we can rest assured that what is possible to be done will be done. But if a sufficient number of trained men are not available much loss of life and damage to property is likely to result.

Jan 1, 1925

By R. W. Pugh, S. L. Ma

"High carbon rods are typically used as the grinding media in rod mills. Usually an AISI I 090 grade of steel is used which provides the high hardness needed for abrasion resistance and sufficient toughness to prevent rod breakage.Work to improve performance in the past has mainly concentrated on increasing the hardness for improved abrasion resistance. This has been accomplished by adding alloys to the steel which uniformly increase the hardness across the rod section.However uniformly increasing the hardness of the rod produces a more brittle product and at high hardness l1evels can lead to rod breakage problems. Heat treatment processes can be used to selectively increase the surface hardness to high levels while maintaining the core at lower hardness levels to give a product that wears slower without breakage. AltaSteel has developed and mill tested a higher hardness heat treated grinding rodThis paper describes the development of a simple model to predict performance improvement with different hardness profiles and the AltaSteel heat-treated grinding rod process. Mill characteristics of the Endako operation are summarized and predicted performance improvements based on hardmess are compared to the approximate 25% achieved in trials running since July, 1991 at this mill. Early results of other mill trials are also presented.INTRODUCTIONAltaSteel, in Edmonton is a major supplier of grinding media. We have a strong desire to continually increase the quality and performance of our products and thereby improve the efficiency of our customers' processes. In the area of grinding rods, we wanted to produce a product with a significant improvement in wear rate. Second to energy, rod consumption usually represents the next highest cost in processing. This paper presents our development of a heattreated grinding rod that has reduced consumption by about 25% in trials to date."

Jan 1, 1993

By Wei Ye, Lei Li, Xianjian Guo, Feng He

The purpose of the paper is to study the smelting process of copper concentrate with high Cu/S ratio produced in Africa or other areas around the world and theoretically analyze the influence of slag type on the smelting process. The paper has compared the processes used successfully in smelters, including CAPEX and OPEX and other factors, to provide reference for the industry to select the best process under specific conditions. INTRODUCTION At present, a great amount of copper concentrates with high Cu/S ratio, with chalcocite being the major source of copper, have been produced or are about to be produced in the Copperbelt in Africa and other countries in the world. The copper concentrate is usually high in copper (~30–55wt.%) and low in sulfur (~10–15wt.%). The conventional processes of smelting-converting and roasting-leaching-electro-winning for treating this type of concentrate is high energy and materials consumption such as electric power\fuels\flux et al. The direct-to-blister (one-step) smelting process can be considered favorable due to a reduction in processing steps. Up to now, there are four copper smelters in the world operating with the direct-to-blister smelting process. There certainly are problems in the process such as high copper content in the slag, strict operation requirement of slag cleaning electric furnace, etc. Except technical issues, the impact of factors on economical aspect such as power and material cost needs to be considered comprehensively in process selection. In this paper the technical issues of direct-to-blister smelting process, including slag treatment process, were analyzed and the comparison to the conventional processes and economic analysis of direct- to-blister smelting process to treat high Cu/S ratio concentrate were done.

Jan 1, 2019

By Victor Rudenno

"Previous methods have employed statistical analysis to model future mineral resources. The method presented in this paper uses Zipj's Law to determine the size and grade of tin deposits still to be discovered. The law is applied independently to both known deposit tonnage and grades. A probability distribution for both 'tonnage and grade is computed/or those deposits still to be located and then, by applying a correlation between tonnage and grade, a distribution of the probability of metal content discovery is obtained.By considering an economic cut-off in metal contained in a deposit, the probability of economic success for the next tin discovery is computed, both for a world discovery and for the special case of Tasmania, Australia. The results indicate a probability of 11-37% on a world-wide basis and 18% chance of economic success in Tasmania.IntroductionIn the past , most attempts to determine the probability of success in finding an economic mineral deposit have relied on the accumulation of statistical data. These data are then used to predict a suitable frequency distribution to assess the probability of finding a deposit of a given size and grade (Singer,1975).The method not only relies on one having sufficient data, but also on the assumption that the data are not biased and that the distribution (usually log-normal) is a correct one. The method presented in this paper, to analyze tin deposits, uses Zipf's Law, which has been recently applied to oil, uranium, lead-zinc and gold deposits by Folinsbee (1977) and to Western Australian gold deposits by Rowlands and Sampey (1977). Tapp and Koniuszko (1978) have applied Zipf's Law to mineral distribution patterns in the Northern Australian orogenic provinces, which has enabled them to make predictions with a relatively small data source."

Jan 1, 1981