Search Documents

By K. G. Wheeland, K. G. Byberg

The occurrence of a secondary, dust-fuelled explosion following blasting of sulphide ores has been reported in mines in many countries, including canada, the USA, Australia and South Africa. However there has been little effort to document the events and develop effective control technology. Following a detailed investigation of an incident at the Geco Di vision of Noranda Minerals Inc. , the company held a conference of interested parties in October 1986 to review the state-of-the-art and to agree on action. '!his paper outlines the causes and effects of such explosions, the key conference points and conclusions, and subsequent information-exchange and teclmology-developrnent activities.

May 11, 1988

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By S. Spigarelli

The creep response of the AE44 magnesium alloy was studied by means of constant load creep tests carried out at 125 and 150°C, obtaining that at the latter temperature the minimum creep rate observed under an applied stress of 100 MPa was two orders of magnitude lower in the investigated alloy than in AM50. The minimum creep rate dependence on applied stress was described by a conventional power-law, e = Aon , where A was a temperature dependent parameter and n was the stress exponent, resulting in a n value close to 30, i.e. by far larger than those observed in commercial alloys with similar Al content. This large difference in creep response was attributed to the precipitation of rare earths (RE) intermetallic phases distributed in the grain boundary zone in form of an almost continuous network of dispersoids that were observed by means of scanning electron microscopy.

Jan 1, 2006

By G. R. Guillet

Important resources of kaolin, refractory clay and lignite, not found elsewhere in Ontario, occur with quartz sand of glassgrade quality in unconsolidated Mesozoic sediments of the Moose River Basin in northeastern Ontario. These materials comprise the Mattagami Formation of Lower Cretaceous age, which overlie in some places a thin Jurassic unit and a thick Paleozoic section, and underlie as much as JOO m or more of glacial and marine sediments and a uniform capping of muskeg. The Mallagami Formation is known from deep boreholes to exceed 100 m in thickness and to consist of two phases: an earlier Type A unit of dark-coloured carbonaceous clays and lignite, and a later light-coloured (Type B) unit of kaolin-bearing quartz sands and bright-coloured refractory clays. Remoteness, poor access, and difficult physical environment have inhibited the exploration and development of these resources.

Jan 1, 1984

By T. H. Patching, M. W. Mikhail

"Data from a standardized procedure for measuring methane desorption rates from samples of Western Canadian coals gave a good correlation (0.994) with the percentage of fines (-0.6 mm) found in the corresponding run-of-mine coal. The correlation was independent of the mining method and the top size of the samples. It is suggested that both methane desorption rate and the production of fine coal sizes are functions of the fissuration of the coal being mined.This relationship, in conjunction with established data of degradation by unit process equipment, may be useful in predicting the amount of fines that will be produced from new seams of coal and by planned new washeries. It also could be a valuable guide in modifying existing washery processes to minimize production of fines."

Jan 1, 1980

By Li Chongyang, Liu Baolan, Jia Xiaolin, Li Suping

An Al/Al2O3 gradient coating applied on a heat-resistant stainless steel was prepared through a slurry process by using aluminum and ?-Al2O3 powders as the transition filler material, alpha alumina as the surface coating material, aluminum dihydrogen phosphate as the binder, and sodium molybdate as the corrosion inhibitor. The effects of heat treatment temperature, adhesive/filler ratio and ?-Al2O3 content on the bonding strength, microhardness and thermal shock resistance were investigated. The crystal phase and microstructure were characterized by XRD and SEM. The results indicated that the composition of the coating changed continuously from surface to coating-substrate interface. The coating could offer high bonding strength and good thermal shock resistance when heat treated at 700°C.

Jan 1, 2010

By B. S. W. Buffam

"The property of Moneta Porcupine Mines, Limited, consists of a group of eight claims in Tisdale township, Ontario. It includes part of the townsite of the town of Timmins, and adjoins the west boundaries of the Hollin_ger Consolidated and Mace properties. The Moneta property was first staked in 1909, about a year after the first discovery of gold in the Porcupine camp. In 1910 the Moneta Company was incorporated and some preliminary exploratory work performed by Nova Scotia Mines of Cobalt. In 1912 English interests advanced $90,000 for diamond drilling and underground work. One drill hole gave high assays, but apparently the records were poorly kept or the cores were interchanged. As a consequence, when underground exploration was undertaken in 1923 it was directed south rather than west and no ore was found . In 1924 about 5,000 feet of diamond drilling was done in the southern part of the property, but without intersecting ore.In 1931 W. E. Segsworth assumed the direction of the property. Diamond drilling commenced on August 18, 1936. The first hole intersected 9.9 feet of ore averaging 1.23 oz. gold a ton. Underground work was started early in 1937. A mill was erected in the autumn and the first gold brick was poured January 29, 1938.The Moneta mill began operation on January 2, 1938, and the following table gives a summary of the production to June 30, 1943, when the mill was closed."

Jan 1, 1954

By Roland Hunt

This paper deals with the practical problems as sociated with blasting a heated pillar remnant. This pillar remnant was the final stage in the blasting of a multi-stag e pillar blast. Production from the previous stages had produced burning sulphide ore, resulting in high rock temperatures in the final unblasted stage. This is an account of how, under difficult conditions, the pillar remnant was blasted.

Jan 1, 1977

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By I. A. Menshikh, S. A. Kotov, N. L. Shinkarkin

All the cycle for conversion of natural and reprocessed uranium of ROSATOM’s “TVEL” Fuel Company is concentrated at the Siberian Chemical Plant. Conversion capacities are located on two sites, i.e. the Radiochemical Plant, which refines feedstock, and the Conversion Plant, which produces uranium oxides and uranium hexafluoride. Liquid radioactive waste arising in the process, after pretreatment, is transferred to a dedicated national operator for underground disposal. Environmental strategies pursued by the Fuel Company involve the introduction of process solutions intended to eliminate liquid radioactive waste and convert it into a solid phase. In the 5–7 years coming, work will be performed to refurbish and upgrade conversion facilities of the Siberian Chemical Plant that will principally change its radioactive waste management scheme. This paper describes the current waste management scheme and sets out planned schemes for management of natural and reprocessed uranium waste, which will be implemented in the refurbishment of conversion facilities of the Siberian Chemical Plant. The new technologies for the management of liquid radioactive waste from uranium conversion described in the present paper have an undeniable advantage over the current technology mainly due to significantly less environmental harm.

Jan 1, 2020

By J. Someehneshin

Nowadays along with population growth, industry development, consumption of mineral resources and the fact that the reserves on hand are running out, the depth of surface and underground mines for further exploitation are increasing. During recent years, in underground mining, the block caving method for low-grade and large-scale deposits has shown a growing rate of application. This method is very cost effective and economically affordable. The dimensions of blocks are one of the most important parameters which should be taken into account since it has been proved to have a great deal of effect on technical issues such as commencement of caving and mine design. Proper calculation of the length and width for a block in this method leads to proper caving and discharging which are the most important stages. Therefore, in this method, the calculation of the optimized dimensions (length and width) of blocks is not only important but also directly helps the productivity of extraction. In this study, firstly for the purpose of facilitation, some assumptions were considered and having used these assumptions for estimation of optimized length and width of block, a relationship based on rock mechanics and physics was explored. Furthermore, some necessary details were added to the said relationship and finally, it was transformed into an inequality. Solving this inequality provides us with the optimized length and width of the block. The explored relationship was analyzed with MATLAB software and the graphs thereof were drawn. In these graphs, each time one of the input parameters has been drawn up in a logical range so that it could be compared with previous states.

Aug 1, 2013

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By T. B. Williams

THE British Columbia Coal Control was established in 1946 as a branch of the Department of Lands. Its functions are the administration of the Goal Act, the making of field and laboratory investigations bearing on the delineation and utilization of British Columbia coal deposits, and the dissemination of information concerning them. The Department of Lands in the Province of British Columbia retains and administers many of the Province's resources until such time as they are actively developed under the departments of Agriculture, of Forests, of Mines, etcc. The work of the Control is one of stock taking and appraising. We are picking up where the geological surveys leave off. In an effort to assist in the orderly, scientific development -of our excellent and extensive' ?Coat resources, we are bridging the gap between exploration and geological examination on the -one hand and mining on the other. All coal analyses required in the course of the investigations, together with? those requested by prospectors and others, are carried out in the very modern and efficient laboratories of the Coal, Petroleum, and Natural Gas Control. At its inception, the Coal Control began an investigation of coal seams in the Peace River area, specifically those contiguous to the Pine River valley about one hundred miles west of Dawson Creek. The occurrence of coal in the Peace River canyon, east of Hudson's Hope, bad been known since 1792, but the first record of production is for 1923.

Jan 1, 1951

Fatalities Incident Four people perished May 15 ? 17, 2006 ??Doug Erickson ??Bob Newcombe ??Kim Weitzel ??Shawn Currie Incident details available at: ??http://www.mediaroom.gov.bc.ca/sullivan_mine/ ??sullivan_mine.htm Outline Immediate facts/observations from incident ?? #1 Shaft Waste Dump closure program ?? Technical investigations under Panel guidance ?? Findings to date and direction ?? Broaden awareness of potential risks

May 1, 2008

By H. J. B. Couto, J. G. S. Puelles, M. L. Torem, R. H. Rojas, A. G. Merma

Understanding the limits of fine particle flotation is fundamental to achieving a significant and selective separation. Conventional flotation processes are not suitable to treat these particles because of their low collision efficiency. This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. In this sense, this study assesses the effect of current density and pH on bubble size in a binary electroflotation cell. An increase in the bubble generation rate was reported with an increase in current density. In addition, at acid pH values, the size of oxygen bubbles increased and conversely decreased at basic pH values; this may be due to the electrostatic attraction between the oxygen bubbles and the anode resulting in a greater nucleation time. An opposite trend was observed with the hydrogen bubbles. These results are in agreement with their electrokinetic studies, which reported that at acid conditions the bubble surface may be positively charged for both the hydrogen and the oxygen bubbles. Finally the bubble size was slightly affected by the electrolyte concentration, resulting in smaller diameter bubbles at higher concentrations.

Jan 1, 2016

By R. W. Luhning, S. D. Gittins, J .. A. Haston

"The Underground Test Facility (UTF) project operated by the Alberta Oil Sands Technology and Research Authority (AOSTRA) north of Fort McMurray has achieved marked success in field testing mining access and horizontal well in situ recovery of bitumen from the Athabasca oil sands.Mine access has provided for effective placing and operation of horizontal wells in the oil sands from a tunnel system in the underlying limestone. Performance of the in situ recovery process, Steam Assisted Gravity Drainage, has substantially exceeded forecasts made at the start of the project. Over-all results of the program to date show great promise for horizontal well in situ technology as a competitive source of bitumen from Alberta's vast oil sands deposits. The potential economics of a commercial expansion at the site are reviewed in this paper.IntroductionIn situ recovery o f bitumen from the Athabasca oil sands has puzzled the oil industry for many year s, but a breakthrough appears close at hand. The Underground Test Facility (UTF) project initiated by the Alberta Oil Sands Technology and Research Authority (AOSTRA) has had notable success in the piloting of horizontal well processes, which offer prospects for commercial development even under the highly competitive situation facing the Canadian industry . This paper describes the project briefly and presents the potential economics of commercial development on the UTF lease."

Jan 1, 1990

By W. B. Timm

Introduction In preparing this paper on Recent Developments in Gold Milling Practice, the idea occurred to me that possibly the best way to deal with the subject would be to take you in thought on a visit to the principal gold mining camps of the Dominion, starting at the east and finishing up in the west, and noting, as we go, the outstanding improvements that have been made in the last few years in the practice of gold milling. Before beginning this tour, I desire to emphasize the debt this country, and particularly our mining industry, owes to that body of trained and experienced men, little heard of, but who, working quietly on their problems, are responsible for these improvements. The metallurgists, to whom I refer, have solved many difficult problems for the mining industry, in connection with the treatment of our complex ores; for instance, the silver-cobalt ores of the Cobalt district, the gold ores of the Porcupine district, the gold-telluride ores of the Kirkland Lake? district, the copper-gold ores of Noranda, the arsenical-gold ores of the Beattie mine, the copper-zinc ores of Flin Flon, and the lead-zinc ores of Kimberley. In doing so, they have maintained the high technical standards of the profession, and the practices thus evolved are noteworthy for their high degree of efficiency. When the price of gold increased from $20.67 to $35.00 an ounce, what had formerly been thought to be a low tailing became almost an ore, so that the metallurgists are now busily engaged upon the problem of putting this railing back in its proper place of being a tailing once more, or from its value, at the present price, of anywhere from 50 cents to a dollar or so per ton, to a few cents per ton. Owing to the changing prices of the metals in the world's markets, still greater improvements in metallurgical practices are imperative. An important contributory factor towards improvement in ore dressing is the aid furnished by the microscope in the examination of ores and mill products. By making possible the determination of the mineral constituents of the ore, their association, and grain size, it gives the investigator a knowledge of his problem, before he does any actual test work. In the Mines Branch laboratories at Ottawa, its use has enabled us to predict how an ore should respond to various methods of treatment.

Jan 1, 1935

By H. C. M. Gordon

IT is essential to the success of any mining op::ration that the roadways through which the material wrought and ocher materials and supplies are to be transported should be kept in such condition that this transportation cart be effected rapidly and without difficulty. The longer the roadway and the greater the tonnage to be taken over it, the more necessary it becomes chat the construction and maintenance of the road be such chat traffic delays can be reduced co a minimum. le is proposed co deal with the development and construction of roadways serving longwall operations and, since a recreating system of longwall is worked, as a rule, only where roadways driven in the solid coal can be readily maintained, the discussion will be confined co advancing longwall roads which are driven through areas from which the coal seam has been totally extracted. In order to construct a roadway through extracted ground in such a manner that it will remain in a state of reasonably good repair without undue maintenance, it is necessary chat everything possible be done to bring the overlying strata co a state of equilibrium as quickly as this can be effected, and the operations should be so planned that future workings will not disturb the equilibrium so set up more than can be avoided. Obviously, the readiest way to obtain a stable roadway is to develop it by tunnelling through a settled waste. However, this cannot always be done, as some of the roadways must be developed and constructed as the walls progress, but level or lateral cut-offs can be constructed in this manner. Main-slope roads can be developed in a similar manner after the coal has been extracted and a waste formed for at !east five hundred feet on either side of the line of the permanent roadway from temporary subsidiary roads developed for this purpose along one or other of the flanks of the waste to be formed. This interval must be obtained in order chat the lacer extraction of the seam will not set up movements in the waste immediately overlying or adjacent to the constructed roadway, thus upsetting the equilibrium of the strata and distorting the road.

Jan 1, 1940

By George Kellock

Introductory The Alberta Provincial Government has contemplated a revision of the Mines Act for some time past, and it is understood that a definite decision has now been made to do this at the next session of the Legislature. The Operators' and Miners' organizations of the Province have been asked, or at least have been given the opportunity, to submit their views and ideas relative to the proposed changes. The operators have already drafted out a number of changes which they feel would improve the Act from the standpoint of safety and practicability, and this paper has been prepared so that the general membership of the Rocky Mountain Branch of the Institute, which is composed largely of the operating and certificated officials of the mines, might have an opportunity to discuss, criticize, and improve upon the suggested changes which the operators are putting forward.

Jan 1, 1929