Search Documents

By P. W. A. Mayer

"As the push toward the northern regions of Canada steadily increases to exploit the rich mineral reserves, interest is steadily rising in respect to accessibility and climatic conditions and the problems posed thereby. In twelve years of operation, the Iron Ore Company of Canada, and associated companies, have found, through advanced technology, ingenuity and, most of all. need, some of the answers to the running of a profitable year-round open-pit mining operation."

Jan 1, 1966

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By P. M. Shibley

"IntroductionMine drainage, surface. drainage and process liquors are the principal mine and mill effluents. The quantity and quality of these flows varies according to mineralogy, type and scale of mining, the process, tailing disposal, local ground conditions and climate.Typical contaminants remaining after solids sedimentation are colloidal or semi-colloidal particles, acids, alkalis, metals in solution, cyanides and thiosalts. Environmental regulations and guidelines have been issued in detail by the appropriate government agencies and will not be reviewed here. Revisions and additions are being made as our comprehension and abilities increase. Some contaminants of consequence have not been specifically regulated as practical treatment technology has not been identified. Thiosalts fall into that category as do the derivatives of the first stage of cyanide oxidation - cyanates.Most mining activities have present or foreseeable water treatment requirements. Because process economics can be adversely skewed by the environmental factor, the acknowledged objective of every operation must be to identify and anticipate those requirements.The evaluation and selection of water treatment techniques for mine-mill applications is complicated by the fact that most mine-mill effluents are high volume, dilute and chemically complex systems. Treatment processes applicable to most contaminants are: chemical or biological oxidation; neutralization and/or precipitation; liquid/solids separation. Other processes such as ion exchange, electro-deposition, foam fractionation, freeze crystallization and reverse osmosis offer the possibility of selective removal or concentration of contaminents. The latter tediniques, representing a slightly higher level of technology, are less suited to the large, low value flows usually encountered in the mine environment."

Jan 1, 1989

By S. N. Kalyakin, D. S. Flett, M. A. Mulagaleeva, N. V. Gudkova, S. S. Serdyuk, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina, V. G. Lomayev

"The Chuktukon niobium-rare earth elements ore deposit is located in Siberia (Russia). Weathered carbonatite crusts are the basis of the ore deposit. The deposit itself is 3.5 km in length, about 800 to 1400 m in width and up to 200–300 m in thickness. The ores are composed of iron-manganese oxides (hydrogoethite, hematite, psilomelane, pyrolusite) and contain 3–7% of rare-earth phosphates (florencite, monazite) and 0.5–1% of niobium oxide (pyrochlore). The ore is completely finely dispersed and consists of oxide particles formed of compact, dense aggregates which makes ore dressing as well as leaching of the rare and radioactive elements very difficult. Several options for processing of these ores have been considered: 1) reduction of the iron oxides to magnetite followed by beneficiation with magnetic separation to produce a rare metal concentrate; 2) processing of the rare earth elements (REE) containing minerals by direct alkaline-acid treatment; 3) processing of the ores using nitric acid leaching in an autoclave.INTRODUCTIONThe Chuktukon niobium-rare earth metal ore deposit is located in Siberia, in the Krasnoyarsk region, 110 km from the Boguchan hydroelectric power station which has recently been commissioned. This mineral raw materials is capable of providing impetus for the modernization of the Russian rare metal industry because of its qualitative and quantitative characteristics. The deposit is located in a region of promising industrial development and is a part of the territoriy where the Russian Federation’s Program “Complex Development of the Lower Angara Region” is currenly being realized. The main program directions are creation and development of industrial activities in sectors such as power, metallurgy, oil and gas, gold, rare-metals, and timber. The program will aid the development of the niobium and rare-metal resources of the Lower Angara and neighbouring regions as well as increase the national production of REE and therefore import substitution (Lapin, 1997; Lomaev & Kuzmin, 2003; Lomaev & Serdyuk, 2011; Serdyuk, Lomaev, & Kontorovich, 2000)."

Jan 1, 2016

By I. Colquhoun

Current practice tends towards "integrity as an afterthought". That is, integrity is treated as an isolated aspect of operations and maintenance. In fact, this works quite well. But it would work so much better and with less uncertainty if integrity management measures were introduced at the design phase and addressed the entire life-cycle of the pipeline asset. The talk will address the measures and metrics that can be implemented on a new pipeline during design to optimize integrity and deliver a comprehensive operating manual and integrity management program for the pipeline system. This deliverable should describe the risks to be assessed and monitored, and the actions to be taken to control these risk adequately. Properly executed, integrity by design will provide a good working estimate of the life-cycle integrity management costs and maximize system reliability.

Jan 1, 2005

"These guidelines set out information on timely disclosure of news releases which are intended to provide, existing shareholders and potential investors, factual information on which a reasoned investment decision can be made.Consider the problems and concerns raised by the following hypothetical news releases:Natural Resource Company""The Company has recently optioned a large and exciting gold property near the ""XXX"" gold discovery area. In describing the property, the Company's independent consultant has said: ""The favourable location of, and some of the results of prior work done on the property give the Company a worthwhile mineral exploration opportunity .... "". The Company proposes to expeditiously conduct a sizeable exploration program on the property as soon as the appropriate financing has been arranged.""Non-Resource Company""Based on discussions with several European countries, the Company anticipates that it will have orders to ship over 200,000 crates of widgets to those European countries over the next two years. These orders, which considerably exceed the Company's forecasts for the first year, represent a projected profit to the Company in excess of $1,000,000 over the next five year period.""GuidelinesTimely disclosure news releases are intended to provide, to both existing shareholders and potential investors, factual information on which a reasoned investment decision can be made. National Instrument 43-101 Standards of Disclosure for Mineral Projects provides requirements for disclosure of a scientific or technical nature for a mineral resource company.The examples do not provide sufficient detail and are misleading because material information is omitted. The following guidelines should be observed when preparing a news release:"

Jan 1, 2003

By S. Rash Ahmadi

One of the most important elements in power plants is rotors and repairing the damaged rotors is very important in view point of economics. One of the most complicated problems in power plants is increasing of stiffness of the turbine rotors. This problem which occurs mainly due to thermal shock or rubbing makes to exit damaged rotor from service. These elements can be repaired effectively by heat treatment methods. Tempering heat treatment is the most common solution for straightening of damaged rotors but it requires having good knowledge about heat treatment parameters (temperature and time) and their affects on fundamental properties of rotors. In this article, a suitable method is introduced in order to modify the increased stiffness in journal part of rotors due to martensite transformation, using heat treatment tempering process.

Oct 1, 2011

"The standards set out requirements of the Toronto Stock Exchange for company’s providing information to investors, regulators and/or the media regarding their mineral properties. In addition, information contained in new releases, continuous disclosure documents [annual report], or other forms of communication [printed investor relations materials and electronic publications] are also subject to these standards.1.0 INTRODUCTIONThe disclosure of the results of exploration and development activity on mineral properties mustcomply with the requirements of the Toronto Stock Exchange Policy Statement on Timely Disclosure, theOntario Securities Act and all applicable policies and rules of the Ontario Securities Commission and anyother securities regulatory body having jurisdiction over an issuer listed on the Exchange. In particular,the requirements of National Instrument 43-101 must be followed.The purpose of the standards is to set out the requirements of the Toronto Stock Exchange when acompany provides information to investors, regulators and/or the media regarding its properties, whethersuch information is contained in a news release, a continuous disclosure document such as an annualreport, or other form of communication, including, but not limited to, printed investor relations material andelectronic publications such as Internet Web sites. These standards do not apply to prospectuses orlisting applications, the standards for which are contained in the policies and rules of the securitiescommissions and the Exchange. These standards are also not intended to establish requirements for thecontent of technical reports.Any information published by or on behalf of a company must comply with these standards. If acompany becomes aware of information published by others regarding its mineral properties which ismaterially misleading to investors, it should take appropriate action to correct such information orotherwise make it known that it is not responsible for publishing such information and does notnecessarily agree with such statements.Disclosure concerning mineral properties should identify the ""qualified person"" as defined in NI 43-101 who is responsible for the work conducted on the property and such person shall have read andapproved of the technical disclosure."

Jan 1, 2003

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By Rashid Bashir

The presence of groundwater in the form of large aquifers can have an important influence on investment decisions for underground mines. The design for such mines requires development of special mining methods, and mine dewatering infrastructure to avoid hazards during shaft sinking and underground development. The costs associated with mine drainage control and Mine Dewatering Systems (MDS) are relatively small compared to the huge consequential losses that can occur in case of an uncontrolled inflow and subsequent flooding of the mine. The design of MDS needs consideration of accurate prediction of the maximum uncontrolled inflow rate, availability of the system during an uncontrolled inflow while the inflow is mitigated, and decision on pumping system technology to have capability to operate under water. The research presented in this paper provides a theoretical framework for a reliability based design procedure which takes into account the uncertainty in the estimate of the maximum uncontrolled inflow, performance of the system during the period of an uncontrolled inflow and a methodology to decide on appropriate pumping technology considering the reliability of the system and available underground storage. The reliability based mine design procedure integrates the ideas of Effective Reserve and Hydraulic Reliability Index to come up with a unified methodology for design of Mine Dewatering Systems.

Aug 1, 2010

By Oberlando Gonzalez, Claudia Serna, Andrea Alzate, Esperanza López, Maria Holuszko

This paper presents a systematic approach on gold recovery from electronic waste (e-waste) using ammonium persulfate. This process was developed as a response to the lack of hydrometallurgical systems capable of separating gold from its metallic substrate without material grinding, with minimum formation of pollutants, and achieving a lower reaction time. Computer memory boards, electronic processors and electronic pins and contacts were analyzed to determinate base metals (Ni, Fe, Cu) and gold (Au) using microwave plasma atomic emission spectroscopy (MP-AES). An aqueous commercial grade ammonium persulfate with oxygen and pressure was used to produce the persulfate anion (S2O82-) and the oxidative sulfate ion (SO42-), which partially oxidized and leached the base metals breaking the Au-Ni-Fe-Cu bonds and allowing gold to be recovered in its original non-leaching state. The influence of the oxidative parameters was evaluated using full factorial (FF) and central composite designs (CCD) with response surface methodology (RSM) and first and second order models were developed. Using RSM allowed to obtain a faster recovery of gold, minimizing the agent consumption. The findings presented suggest that optimized quantities of ammonium persulfate, oxygen, pressure, temperature and liquid solid ratio could be used for selective oxidization of the base metals and to extract more than 96% of gold from e-waste.

Jan 1, 2017

By Rashid Bashir

Shaft sinking through solid rock, which contains little or no water, poses little difficulty. However, when loose, water-bearing strata have to be contended with, water control measures, and pumping facilities are needed. Shaft sinking in Athabasca Basin requires sinking through water bearing sandstone which can be highly fractured. Intersection of local zones of extensive fracturing results in the potential for high water inflows with pressures up to 5 Mpa. Grouting is carried out ahead of each shaft sinking interval as water control strategy. In the grouting method, liquid cement is forced into the water-bearing earth under very high pressure. Shaft sinking performance which can be quantified in terms of rate of advance is highly dependent on the days spent at each interval grouting before sinking can advance to the next interval. This paper presents the shaft sinking experience in Athabasca basin and how some of this is translated into Geoscientific Investigations for Future Shafts. A comparison of Geoscientific data collected from future shafts at McArthur River and Millennium Mines is compared to historical data collected from pilot holes, where shafts have already been sunk. The paper concludes with the strategies for better integration of hydrogeological, geotechnical and geophysical data.

Aug 1, 2010

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

"This document establishes standards and guidelines for scientific and technical disclosure by Issuers listed on the TSX Venture Exchange on their mineral properties. It incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.1. Introduction1.1 General(a) This Appendix establishes standards and guidelines for scientific and technical disclosure by Issuers on mineral properties. These standards and guidelines should be applied prudently and with common sense by those Issuers in conjmction with the applicable requirements of section 1.2.(b) This Appendix incorporates and expands upon the minimum standards prescribed by Securities Laws and applies to all oral statements and -written disclosure made by an Issuer or on behalf of an Issuer involving mineral properties.(c) This Appendix is not intended to be exhaustive or all-encompassing and greater detail may be appropriate and required in certain situations. Issuers are encouraged to contact Exchange technical staff where they are not certain about the requirement for disclosure on mineral properties."

Jan 1, 2003

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

Introduction A Hypothetical Scenario: Suppose that your company's research department has developed a new device which represents a significant innovation. You would like to begin selling it as soon as possible. The new device has not been publicly disclosed. You're not sure about what type of intellectual property protection you should be seeking, or when you should be seeking it. As discussed below, assuming that the costs are worth it, a patent application probably should be filed before any public disclosure is made. In general, if you do not file a patent application prior to a public disclosure, you will lose rights. Major Types of Intellectual Property In this paper, intellectual property protection is broadly discussed. Practical steps which can be taken to minimize the possibility of losing intellectual property rights (and maximizing the possibility of benefiting from your company's intellectual property) are outlined at the end of this paper. The issues discussed in this paper are somewhat complex, because a number of outcomes are possible, depending on the facts. It is strongly recommended that you seek legal advice in your jurisdiction in connection with any particular circumstances relating to intellectual property rights. "Intellectual property" refers to a number of different types of rights. The major types of intellectual property are: (i) patents; (ii) trademarks; and (iii) copyright. Trade secrets are also usually considered to be a type of intellectual property, and they are also discussed in this paper because of their importance. In general, each of these types of intellectual property protects different subject matter, although there can be some overlap. Intellectual property rights are generally territorial in nature. The scope of protection of a type of intellectual property in a country (e.g., patent protection) depends on whether the specific national requirements for protection have been met.

Feb 1, 2008

"These standards were developed by the CIM for use with the value or worth of a Mineral Property as opposed to “evaluation” where the key objective is an economic assessment or determination of the economic merit of a propertyP1 .0 BACKGROUNDPl.1 There are at present no comprehensive standards for valuation of Mineral Properties in the Canadian mining industry. The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) specifically recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties.Pl.2 On May 5, 1999 at the Calgary Annual General Meeting, CIM Council approved the formation of a Special Committee on Valuation of Mineral Properties (CIMV al) to be co-chaired by Keith Spence (Chairman of the CIM Mineral Economics Society) and Dr. William Roscoe (Roscoe Postle Associates Inc.).Pl.3 The mandate of CIMVal is to recommend Standards and Guidelines for Valuation of Mineral Properties to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges.Pl.4 The members of CIMVal represent of a mix of professional disciplines and experience in the field of Mineral Property valuation:Keith N. Spence (Co-chair), Alliance Pacific Resources Inc., TorontoWilliam E. Roscoe (Co-chair), Roscoe Postle Associates Inc., TorontoMichael J. Bourassa (Secretary), Aird & Berlis LLP, TorontoChristopher R. Lattanzi, Micon International Limited, TorontoRoss D. Lawrence, Watts, Griffis and McOuat Limited, TorontoPaul E. Lunney, Noranda Inc., TorontoCraig A. Roberts, Pacific International Securities, VancouverDavid A. Scott, CIBC World Markets, TorontoIan S. Thompson, Derry, Michener, Booth & Wahl Consultants Ltd., VancouverWilloughby A. Trythall, retired Placer Dome executive and consultant, Vancouver"

Jan 1, 2003

By M. Loan

The Zinifex's Hobart Smelter uses the paragoethite process to remove dissolved Fe(III) from concentrated zinc leach liquors. This produces a residue consisting primarily of 6-line ferrihydrite (a hydrated Fe(III) oxyhydroxide), several insoluble components derived from the calcined zinc concentrate neutralization agent and other precipitated phases, such as jarosite and silica. The precipitation of 6-line ferrihydrite in the paragoethite process was studied using a laboratory-scale continuous crystallizer, and the conditions were selected to limit high levels of dissolved silica and jarosite. This approach allowed the reactor pH and the rate of precipitation to be correlated with residue solid-liquid separation, particle size, morphology, residual zinc and sulfate concentrations, and phase formation (e.g., goethite, jarosite, schwertmannite, and 2- and 6-line ferrihydrite). These studies delineated the mechanism of 6-line ferrihydrite precipitation in the kinetically controlled paragoethite process, and its inter-relationship with goethite and jarosite precipitation under conditions where 6-line ferrihydrite is favoured. Unexpectedly, the generation of a more crystalline goethite precipitate with larger "primary" particle size did not produce a residue of improved properties, as bulk aggregates dictate the physical properties of the residue and not the crystallinity. Furthermore, it is difficult to precipitate 2-line ferrihydrite or schwertmannite under existing paragoethite process conditions.

Jan 1, 2006

By B. Farabi Khoshmehr

In the present study the effect of Silicate Sodium oxidation agent concentration and Plasma Electrolytic Oxidation (PEO) treatment time were investigated on properties of oxide layer on Aluminum alloy. The phase composition and surface morphology of PEO films were evaluated through x-ray diffraction (XRD) and scanning electron microscopy (SEM). Pin on Plate abrasive machine were used to investigate of were resistance of coating. The results showed that oxide layer which formed on Aluminum surface consist of high temperature a- Al?O? and ?- Al?O? phases. The diffraction peak intensity and percentage of these phases were increased by increasing silicate sodium concentration. Microscopic studies revealed a porous surface for PEO coating. This was affected by silicate sodium concentration and oxidation time. The wear test results showed that the weight loss of PEO coating was reduced due to improvement of their wear resistance.

Oct 1, 2011

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019