Search Documents

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By The Staff

"THE Wabana iron ore mines, owned and operated by the Dominion Steel and Coal Corporation, Limited, .are on Bell Island in Conception bay, on the east coast of Newfoundland. Mining began on surface in 1895 and, although open-pit work is still done on a small scale, the entire output may be considered to•be derived from extensive submarine workings. In 1958 the average daily production of hematite ore was close to 12,000 tons, almost all of which was concentrated in a heavy-media plant. SUMMARYThe character, occurrence, and extent of the submarine bedded deposits enabled early operators to meet prevailing market demands with the minimum attention paid to exploration. Mechanization of the mine and the pressure for sustained high tonnages since 1955 have emphasized the importance of an expanded exploration and development programme.A serious handicap has been the impossibility of utilizing normal diamond drilling methods to explore ore conditions in advance of mining faces. Drilling between tl1e bedded zones has been done but the major difficulty has been to delineate ore reserves in the lower bed, which has the greatest ore potential of the three mineable seams."

Jan 1, 1960

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The project implementation phase, FEL4, is generally a complex undertaking. The project has been approved for construction and the capital has been allocated. At this point the project team comes under significant pressure to meet the safety, schedule, cost, and start-up committments. For the design team the principal tasks are to finalize detailed design, complete procurement, and issue construction contracts. Design activities must be closely coordinated with equipment and material procurement. A clear engineering plan should be based on well-defined work packages to meet construction, commissioning, and startup requirements. A range of review processes by discipline, area, and third parties assure quality. Constructability, safety, and hazard reviews are performed throughout the design process. Three-dimensional models that incorporate extensive databases help to maximize efficiency and minimize errors. Well-managed projects have a clearly accountable design team, rigorous change control processes, and well-defined workflows. Key individuals from the design team participate in commissioning, operator training, and startup.

Jan 1, 2015

By L. E. Djingheuzian

ANON-CATARACTING (N-C) ball mill is so operated that the balls are not thrown in-ward at the top of their paths. The result is to maintain, in the mill, a quiescent pool in which classification will occur at a limiting size corresponding to the pulp density. N-C operation is produced by effecting proper relationship among mill speed, ball diameter, volume of ball load, and pulp density. Such operation is typified by the primary ball-mill operation of the Tennessee Copper Company, Copper-hill, Tenn., and the Cleveland Cliff Iron Company, near Ishpeming, Mich.

Jan 1, 1958

By T. G. Carter

"Tremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems, with amongst the most advanced of the tools focusing on evaluating engineered openings within Synthetic Rock Masses. These new codes have the potential to allow much more realistic design, but they must not be used without careful calibration – prior to – during and – post completion of any modelling. This paper explores some of the pitfalls of inadequate data collection and suggests more emphasis be given to calibration. Guidelines for minimum levels of parameter data are suggested for improving application of basic to sophisticated modelling codes.INTRODUCTION & BACKGROUNDTremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems. The degree of sophistication now possible with some of the available codes allows one to tackle extremely complex problems that were not thought tractable even a decade ago. Indeed, generation of synthetic numerical rock masses, based on discrete fracture network representations that closely mimic actual rock mass conditions, such as are shown in Figure 1, is today relatively straightforward, and not as user-challenging as employing state-of-the-art codes of even a few decades ago. This is largely because major improvements in computer graphics and in availability of ready-made user-friendly input-output interfaces have paralleled development of these new codes, now in some cases outpacing actual new analytical/procedure developments. This is something of a reversal from the first few decades of DOS-based rock engineering computational experience, when only rudimentary graphics were available and user-friendly input-output interfaces were virtually non-existent."

Jan 1, 2015

By J. E. Rowland

NIOCALITE is a new mineral species which has been identified in rock from the Oka district, Quebec. It occurs as prismatic crystals up to l 0 mm. in length and I mm. in width, in coarse, white, crystalline calcite with associated apatite, diopside, biotite, pyrochlore, and niobian perovskite. The crystals of niocalite are light yellow in col-our and have a vitreous lustre. The optical properties of niocalite (I) are as follows: Biaxial negative -2V = 56° a = 1.700, [ ] = 1.730 Birefringence y -a = 0.030 Optic orientation: X = b, Z/\c 12°, Y , /\a = 32° The specific gravity is 3.32 and the hardness is approximately 6 (Mohs scale). A detailed analysis performed on 2.4 gm. of hand-picked material reveals that niocalite is essentially a calcium niobium silicate. Table I gives the result of the analysis. Crystals of niocalite, apparently suitable for X-ray diffraction work, were selected, and single crystal photographs were obtained using both Weissenberg and Precession cameras. Initial difficulties were encountered in interpreting these films, and in correlating the crystal data with the optical data. The in-consistencies were explained by the fact that every grain examined was twinned to some extent.

Jan 1, 1957

By Al Hoffman

During the period May 15 ? 17, 2006 four fatalities occurred at #1 Waste Dump, at Teck Cominco?s Sullivan mine located at the city boundary of Kimberley, British Columbia, Canada. The fatalities occurred in the sump of a water monitoring station. The Chief Inspector of Mines and his staff immediately responded to the incident. The team worked collaboratively with the Teck Ltd. Trail Hazmat team, a consultant group from Rescan Ltd. and other Teck operation and technical staff. Sampling in and around the water monitoring station in the days following the fatalities showed that exposure to a depleted oxygen environment was the immediate cause of the fatalities. The sump located at the base of the shed was hydraulically connected to a French (coarse rock) drain, located at the toe of the covered waste dump. This presentation will briefly review the immediate cause of the accident, the investigation, a brief introduction to the work of the Sullivan Technical panel and the British Columbia government?s response to the incident and the recommendations of the Coroner?s inquest.

May 1, 2010

By L. Fernandes

A factorial study was performed to investigate the relative effects of temperature, copper concentration and meso-2,3-dimercaptosuccinic acid (DMSA) concentration on the performance of thiosulfate leaching of gold. A total of 24 leaching experiments were performed representing eight unique combinations of high-low levels of the three factors performed in triplicate. All investigations were performed in an electrochemical cell with an electrolyte composed of 0.1 M sodium thiosulfate with a combination of copper (either 0 mM or 1 mM) and DMSA (either 0???or 1µM). All leaching investigations were conducted under open circuit while the electrolyte, which was open to the atmosphere and mechanically stirred, was maintained at either 25°C or 50°C. After 1.5h of leaching the amount of gold in solution was quantified using ICP-MS analysis from an aliquot of the electrolyte. Results indicate that DMSA addition improved gold leaching performance, most notably at 50°C and with addition of copper. Under this unique condition, the quantity of gold in solution was reproducibly and significantly above the average response of all other factors studied.

Jan 1, 2014

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By Marc C. Bétoumay

Workplace safety, health, climatic conditions and rising oil prices are aspects that are important to the mining industry. The need for cleaner energy for underground mine vehicles is requiring serious consideration. A number of alternate energy systems offer clean solutions to diesel emissions while maintaining the current liberty of vehicle movement. This watershed article provides a broad comparison of cleaner diesel and alternative energies for underground production vehicles. Most alternate energies and clean diesel have already been tested in underground production vehicles. There are no technology gaps that would prevent the development of commercial alternative energy power plants, but in the case of alternate energies, second and third generation versions will be required to fully test for safety and operation viability. Full regulatory development is also required and could be done in parallel to power plant testing. Vehicle operation and maintenance manpower would be the same for alternate energy application as for clean diesel. Capital cost for alternate energy power plants will remain higher until the medium term. Owing to significant ventilation savings possible with alternate technologies, operating costs would be reduced.

May 1, 2011

By Julian Boldy

"A review of lI5 significant volcanogenic massive sulphide discoveries in the Canadian Precambrian during the past 65 years reveals that only 7% resulted from surface exploration methods aimed at depths below the effective reach of current geotechnical systems. This has been due to the relative ease of shallow discovery, resulting in the harvesting of ore deposits within 100 m of surface. This surficial layer has been more or less effectively supersaturated by routine exploration. In view of the fact that a mining district's metal content is not likely to be confined to a surficial layer, the time has come to explore the vertical dimension, prospecting for ore at depths in excess of 150 m in productive districts.Essential to this task is an understanding of the Precambrian volcanogenic ore deposit model. The deposits generally have .a tendency to be associated with the terminal phases of felsic volcanism, and to be located along certain time-stratigraphic horizons, marked by the products of volcanic exhalation. The significant massive sulphide deposits are discrete entities, ranging from the top 5% of deposits greater than 45 million tonnes in size, with a surface area of 0.30 km2, to median-sized deposits greater than 1.2 million tonnes in size with a surface area of 0.02 km2. These significant economic ore deposits range in value from $5.5 billion for the top 5% of deposits to $125 million for median-sized deposits. In terms of their frequency of occurrence, the former group has a 4% distribution and the median-sized deposits have a 15% distribution.An historical review of many of the principal Precambrian mining districts, such as Noranda and Flin Flon, shows that major tonnages are usually discovered during the initial phase of application of each new geotechnical search system, until carried to its ultimate limit of effective depth penetration. With the exception of the Noranda district, the mean depth of ore discovery in the other districts is still generally confined to within 50 m of surface.Targeting deep ore is difficult. One effective prospecting method is the detection of fracture-controlled mercury leakage haloes in outcrop (or core) above and peripheral to blind deposits. This technique has proved to be a useful pathfinder, and focuses attention on deposits buried at depths in excess of 700 m in some instances. Down-hole EM systems also promise to be effective in locating deposits previously bypassed by drilling. In addition, trend surface analysis programs of trace element geochemistry should be used as an aid to targeting ore by directing exploratory drilling along the plane of ore-hosting stratigraphy.By definition, mining districts have a proven ""favourability"" for the occurrence of ore. Discovery probabilities in these districts will be considerably enhanced if future search efforts are concentrated below a depth of 150 m, and more use is made of ""deep"" ore search systems coupled with sound geological reasoning. Deep drilling programs to a depth of800 m should initially be designed to search for the top 25% of deposits greater than 3.3 million tonnes in size, with a surface area of0.05 kmt. :a value of$310 million and a 12% frequency of occurrence; This can be accomplished for an over-all cost approximating $40,000 per drill hole. If the search depth is limited to 400 m, the over-all cost of each drill hole is $20,000, equivalent to expenditures routinely allocated to grassroots exploration drilling in the remote greenstone belts of the Precambrian. Depending on a company's objective, prospecting for deep ore offers a stimulating challange - though risky, it has its rewards."

Jan 1, 1981

In this study, flotation of fine galena, chalcopyrite and pyrite was performed after grinding with different extent of oxidation-reduction condition adjusted by grinding media. Sodium dithionite and iron ions were added in mill to simulate pulp potentials and iron oxidation species produced by grinding media, respectively. The types and quantities of the metal oxidation species on mineral surfaces were determined by EDTA extractions, while the surface electrical properties of minerals and interaction of different types of metal oxidation species were studied by zeta potential measurements. It was found that the nature and concentration of the absorbed metal oxidation species were dependent on oxidation atmosphere controlled by the iron amount of grinding media. These species interacted with each other and had an important role in determining flotation of fine galena and chalcopyrite as well as activation of fine pyrite by lead and copper.

Jan 1, 2006

By M. Solomon

Giant, sediment-hosted lead-zinc deposits in northern Australia fonned during development of Mid-Proterozoic extensional basins that overlie Lower Proterozoic basement. The basement in the Mount Isa area, exposed by folding and faulting, contains fractionated, high-heat-producing granites. These granites generate heat at a rate of about 6",Wm-3, probably sufficient to fonn giant lead-zinc deposits either by (a) driving episodic convection of saline basement and basin fluids for periods of IOS to 106 years at temperatures of about 230°C, or (b) heating basin fluids moving under the influence of topographic relief or fault movement. The presence or absence of such granites may form a vital component of the genetic model. Ore-fonning fluid flow was probably initiated by continent-scale, extensional basin fracturing.

Jan 1, 1992

By G. J. Kipouros, N. Dadvand

"In recent years coatings of alloys have been produced for a wide range of applications including many for wire bonding application. The main characteristic of the baths of electroless plating is the presence of sodium hypophosphite as a reducing agent and also as the supplier of phosphorus. In the electroplating of alloys the Watts bath is predominantly used. This presentation compares the two techniques, electroless plating and electroplating, and discusses the possibilities of cross utilization of sodium hypophosphite in an attempt to formulate baths that eliminate the waste disposal issue related to some components.INTRODUCTIONThe importance of surface characteristics and the linkage of surface coating process to surface characterization has given rise to the evolution of surface engineering. Not only the surface preparation and morphology has become very important to the coating technology but also the knowledge of surface area exposed to the process of coating or corrosion is absolutely essential in ascertaining the behaviour of coatings and their adherence to the substrate. The above concepts are not unknown to researchers involved in the protection of surfaces, particularly metallic, from corrosion and/or erosion corrosion. However, the complexity of the surface defects, roughness, porosity, interconnected porosity and other related factors have contributed to the uncertainty of the true surface area versus the nominal surface area. Therefore critical parameters such as current density and chemical surface intensity although have been studied extensively at the atomistic level by carefully prepared surfaces are very difficult to be determined at the practical scale required during the coating processes.The most pronounced case calling for an understanding the relationship between the surface area and the effective protection is the coating of surfaces of items produced by compression or consolidation of powdery materials. With the advent of nanomaterials and the additive manufacturing through 3D metal printing this issue is becoming more important. Certain experience in this field come from the accumulated knowledge resulted from the attempts to characterize the electrochemical behaviour of powder metallurgy metals and alloys. Powder metallurgy has been a well-established process for half a century on basic metals such as iron, copper and their alloys. Recently the development of powder metallurgy process for aluminum, titanium and attempts to develop powder metallurgy processes for magnesium and its alloys has brought to light another important issue that of the development of coatings on difficult to plate reactive metals such as aluminum and magnesium. Despite of many successes in the development of powder metallurgy alloys the exact characterization of the corrosion behaviour of the coatings and the substrates is difficult to determine because of the unknown morphology of the exposed area i.e. the exact morphology and area of the exposed surface (Samal, 2007)."

Jan 1, 2016

By J. A. MacLellan

"CONSTRUCI'ION OF SHERRITT'S CONCENTRATORSSherritt Gordon is operating two mills north of the 56th parallel, and is presently engaged in building a third. The author was closely involved in the design and construction of all three of these concentrators.The Lynn mill is the oldest of these three concentrators-it is a 4,000 ton per day nickel-copper plant built in 1953. The Fox mill is a 3,000 ton per day copper-zinc concentrator built in 1970. The Ruttan mill will be a 10,000 ton per day copper-zinc plant scheduled to go on line in July 1973.LYNN MILL The Lynn mill including the crushing, concentrating, drying and load out plant is about 69,700 square feet or 17.4 square feet per ton per day. '!his plant was originally built in 1927 at Sherridon, 150 miles south of Lynn Lake, as a 2,000 ton per day copper-zinc plant. In 1952 the plant was moved by tractor train to Lynn Lake. The whole plant was re-oriented within the original perimeter walls as a 2,000 ton per day nickel-copper plant. This plant was expanded to 4,000 tons per day by the addition of t1-Jo rod mills and a 5-1/2 short head crusher in 1959.The Sherridon mill processed its last ore in Sherridon in September 1951 and the first load of nickel concentrate was loaded at Lynn Lake on November 9, 1953 when the railroad arrived at Lynn Lake.The site for the Lynn Lake mill was cleared of overburden in the summer of 1952 and foundations for structural steel and SO!l8 equipment foundations were poured the late summer and fall of 1952 • Steel was erected from January to June 1953. Most of the equipment came in from January to March of 1953 by tractor sleighs. Sane sleighs upset but no equipment was lest through the ice."

Jan 1, 1972

By T. Thriveni, Ji Whan Ahn

"The current advanced technologies for the manufacture of light weight metals processing significantly increasing and attributes to the safety, performance, recyclability and economy. Still lack of technologies developed for light weight metals processing waste utilization and application. Environmentally friendly methods need to develop for better understanding the processing waste utilization. Alumina and aluminium processing creates a wide range of waste products, the most significant being is red mud. Bauxite residue is a high volume hazardous waste and nearly 3 billion tons have been dumped worldwide. Approximately, 120 Million tons/yr of red mud being produced without any environmental sustainable solution. Currently the most significant technology is waste utilization. The bauxite residue is suitable for road base construction, golf bunker sand, back fill and, general fill. Sustainable recycling technologies are necessary for the bauxite residue utilization for the recovery of rare earth elements and cement materials. Carbonation or CO2 sequestration of carbon dioxide is a method pioneered for the bauxite residue is modified to reduce alkalinity. The carbonation of alkaline material is an inexpensive and safe process that leads to the formation of thermodynamically stable products. The use of the carbonation can be an advantageous solution for environmental climate change and sustainability problems in the new century.INTRODUCTIONIn 2014, bauxite consumption was estimated to be 9.6 million tons, nearly all of which was imported, worth an estimated 269 million dollars. More than 95% of the bauxite was converted to alumina, and the remaining 5% went to non-metallurgical products, such as abrasives, chemicals, proppants, and refractories. Global aluminum demand is growing steadily spurred by growth in India and China (RBCAluminum Market Outlook, 2013) (Figure 1). Aluminum consumption is expected to rise 5% annually through the end of the decade, reaching 67 million tons per year by 2020. Global bauxite production decreased by 17% from that of 2013, principally owing to lower production in Indonesia. In response to a Government ban on exporting bauxite and other unprocessed mineral ores that took effect on January 12, 2014, bauxite mines throughout Indonesia shut down and production decreased from 55.7 million tons in 2013 to an estimated 500,000 tons in 2014. The ban was part of a mining law that was instituted in 2009 to increase development of downstream processing facilities in Indonesia."

Jan 1, 2016

By K. Hawboldt, J. E. Halfyard, C. Bottaro

The removal of sulfur from leach residues has been practised in the zinc industry using a combination of flotation and hot melt filtration. The process is highly dependent on the nature of the concentrate and the subsequent residue. When the mineral constituency of the residue alters, the process can encounter significant operational challenges. An alternate method of converting elemental sulfur to water-soluble polysulfides was applied to leach residue from Vale's nickel demonstration plant in Argentia, Newfoundland. Reaction parameters, sulfur purity and other key indicators are discussed as is the potential commercial application.

Jan 1, 2011

By P. Czaja

The paper presents a patented and copyright protected concept of constructing a shaft lining that goes through rock masses having strong rheological properties and being susceptible to leaching. In the case of salt layers, especially at significant depths (over 900 m) the relative convergence of the heading contour may amount to 40 ?/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, will not be sufficient to ensure the stability of the shaft reinforcement geometry. In the new shaft lining concept the excessive rock creep into the outbreak inside the shaft diameter will be removed by local and controlled leaching of the shaft cheeks by means of fresh water directed through a porous medium at the contact layer behind the watertight tubing lining. The paper presents the structure of such a lining and an outline of the construction technology. In order to implement such a lining, a typical tubing will be applied. Separate design and manufacturing will be required for the technological rings used to control the leaching process behind the lining.

Aug 1, 2013

By Simon Weixiao Sun

Conventionally, carbon steel has been the primary material for salt mine headframe construction, protected by specialty paint layers to prevent corrosion. These layers require meticulous QA/QC during fabrication and erection, and the top UV protection layer typically loses effectiveness after an average of 10 years, necessitating ongoing maintenance. As headframes age, significant structural repairs are often required. Alternatively, stainless steel can eliminate corrosion concerns, though its high initial cost has limited its use in headframe design. However, when factoring in long-term maintenance costs, a 'maintenance-free' stainless steel headframe can be an attractive option for stakeholders. This paper compares the structural performance and economic considerations of painted carbon steel and stainless steel headframes, including initial capital and long-term maintenance costs. Additionally, it explores a hybrid approach, strategically using carbon steel in low-contamination areas to reduce initial costs and significantly minimize future maintenance efforts.

May 4, 2025

By J. G. Peacey, G. Csicsovszki

The target of this study was to clarify the role of lead on the dissolution of gold in the (NH4)2S2O3-Cu leaching system via chronopotentiometry, linear sweep voltammetry and chronoamperometry. It was found that the dissolution of gold was significantly increased with lead concentration up to 10 mg/1 Pb in the system of 0.1 M (NH4)2S2O3 and 50 mg/1 Cu. \/oltammograms suggested that the anodic dissolution of gold was virtually independent of lead concentration in the range of 1-10 mg/1 in 0.1 M (NH4)2S2O3 solution while in solutions containing copper as well, addition of lead increased the anodic dissolution of gold.

Jan 1, 2011