Search Documents

By Feng Xue, Mi Xujun, Peng Lijun, Yin Xiangqian, Liu Dongmei, Xie Haofeng, Huang Guojie, Yang Zhen

The Age-hardening Cu-Cr alloys are extensively used in integrated circuit lead frame, railway contact wire, resistance welding electrode and continuous casting mold copper plate, owing to having an excellent combination of high electrical or thermal conductivity and high strength. High temperature performance is very important during the service process. Effect of Magnesium and Zirconium on softening behavior of Cr-Cr alloy are investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). During the softening process in the Cu-Cr alloy, the recrystallization process, grain growth and Cr precipitates coarsening are observed. The addition of Mg or Zr to the Cu-Cr alloy, the resistance to elevated temperature can be significantly improved, owing to being restrained the growth of the precipitates by segregating along precipitates surface. INTRODUCTION Age-hardening Cu-Cr system alloys can be widely uesed in many fileds such as electrodes for spot welding (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012), intergrated circuit lead frame (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003; Cheng, Yu & Shen, 2014; Zhang et al., 2016; Li et al., 2007) and railway contact wire (Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003), because it has high strength, good electrical and thermal conductivity. The precipitation behavior of binary or ternary Cu-Cr alloys had been investigated by many researchers (Chbihi, Sauvage & Blavette, 2012; Peng et al., 2017; Batra et al., 2002). In addition, to obtain additional mechanical properties without much deterioration in electrical conductivity, trace addition of alloying elements like Zr, Ag, rare metals (Y and Ce) and Mg are added into Cu-Cr alloy. The addition Mg to Cu-Cr alloy accelerated the process of precipitates nucleation and restrained the growth of the precipitates by segregating along precipitates surface during aging, which enhanced the stability of the deformation microstructure and improved the mechanical properties of the alloy (Zhao et al., 2018). Additional zirconium in Cu-Cr alloy enhances the strength by the decrease in inter-precipitate spacing of Cr precipitates and the formation of Cu5Zr phase (Chihiro, Ryoichi & Kazue, 2008). Owing to the decrease in inter-precipitation spacing of Cr precipitates and to the Ag-atom-drag effect on dislocation motion, the addition of Ag can increase in strength, stress relaxation resistance and without much deterioration in electrical conductivity (Chihiro, Ryoichi & Kazue, 2008). The enhance in strength and electrical conductivity of the Cu-Cr-Zr alloy by adding Ce and Y elements are attributed to removing oxygen and sulfur from as-cast alloy (Li et al., 2006). However, the effect of Mg or Zr element on microstructure and properties of Cu-Cr alloy during the softening process are not clear. Therefore, Microstructure evolution and properties of a Cu-Cr systems alloy were investigated in detail by OM and TEM. The Relationship between microstructure and properties of Cu-Cr systems alloy was also discussed.

Jan 1, 2019

By C. Schlumberger

INTRODUCTION The object of the present paper is to discuss, from a geological point of view, the practical results obtained by the authors with the method of the 'resistivity map of the subsoil' in the study of various mining problems. Some of the studies described date from 1920, 1922, and 1923. They are, therefore, quite old, at least as far as geophysical research is concerned (1). Others, on the contrary, are very recent (2). We shall deal only very briefly with the theoretical and technical sides of the processes employed. This paper has, essentially, a practical purpose, and it has seemed unnecessary to enter into a detailed discussion of the methods. Such a discussion cannot be presented without introducing ,quite. Complex considerations both of mathematics and experimental physics, which interest only the geophysicist: whose work is highly specialized.

Jan 1, 1931

By Sandeep Singh Sandhu, Karanvir Singh Ghuman, Manjit Singh

"Cobalt based super alloy stellite 6 was weld cladded on AISI 304 L stainless steel using SMAW process in order to improve the wear resistance for tyre crusher blades. Microstructure characterization and micro hardness testing was performed on stellite 6 cladding. The suitable parameters viz. 80 Amp current with arc weaving technique was selected by performing bead on plate experiment were further used for depositing multipass multilayer cladding to achieve full filler chemistry at the top surface. Further GTAW process was used for re-melting the top surface of the cladding. Comparative evaluation of the claddings showed that TIG re-melting resulted in increased microhardness and wear resistance in comparison to as cladded specimens even with lesser deposition of material. It was observed that TIG re-melting improved the hardness from 603 HV0.5 kg to 712 HV0.5 kg. Micro structures of stellite 6 contained cobalt solid solution matrix along with inter dendrite chromium carbides which resulted in the increased micro hardness values. Pin on disc abrasion tests were carried out at room temperature and the worn out surfaces were characterized using SEM and EDS.INTRODUCTIONThe crusher blades are used in many industries for crushing various types of material and its wider applications in tyre rubber crushing mills, metal-powder crushers industries etc. Most of the crusher blades are damaged by the wear and impact loading conditions. It is because of metal to metal abrasion and the temperature also plays a vital role in blunting the cutting edges of these blades. The wear is the major cause which leads to loss of material and thus the productivity that can never be recovered (Kotechi et al., 1992). The wear can be reduced by coating of various super alloys which could reduce the behavior of metal degradation even in aggressive environments. Cladding of cheaper low alloyed material with expensive superalloys to enhance the performance of components at low cost has been investigated by many scholars (Deng et al., 2010, Kennametal, 2007, Lolla et al., 2014, Singhet al., 2014, J.N et al., 2003, Ramkumar et al., 2012). Many researchers have reported that cladding is an application of build-up deposits of specialized alloys to resist abrasion, high temperature corrosion and impact loadings. Cladding is used for providing required mechanical strength properties as well as inhibition of oxidation and other corrosive degradation. Coatings are used to protect the heat affected areas like tubes of fluidized bed combustor etc. (Kirchbner et al., 2008, Wang et al., 1994, Hocking et al., 1993, Ananthapadmanabhan et al., 1991, Staia et al., 2001). Coating techniques are widely used for the protection of turbine engine and boiler tubes against high temperature corrosion attack, power generation equipment, chemical process equipment, aircraft engines, pulp and paper processing equipment, bridges, rollers and concrete reinforcements, orthopedics and dental, land-based and marine turbines, ships. Coatings of stellite 6 are widely used in steam turbine blades and boiler tubes for power generation because of an excellent combination of impact, wear and other properties. It can maintain its properties even at high temperature and in harsh environments (Kobayashiet al., 1999, Alam et al., 2009, Munehru et al., 2009). The loading and unloading conditions experienced by the material may induce the surface cracks which lead to its breakage and leaving large pits in the surface (Meng et al., 1995). Many researchers have reported that the properties of cladded layers can be increased by various techniques such as controlling the current variations, dilution, heat input, laser and other re-melting processes, addition of special alloying elements, speed of weldingetc(C.M Anaet al., 2002, Kumaret al., 1999, Luo et al., 2012, et al., Madadi et al., 2011, Shin et al., 2003, Kuzucu et al., 1997, Sudha et al., 2008, Sawant et al., 2017, Houdkova et al., 2016, Ciubo"

Jan 1, 2017

By N. Manopulo, J. Maier, L. Tong, C. Becker, P. Hora

The contribution presents a new finite element approach in which the common updated Lagrangian formulation is replaced by a spatial flow formulation applying a special arbitrary Lagrangian-Eulerian for-mulation (ALE). The description separates spatially the process in a die inside zone and in a profile zone. For the description of the inside zone, where the filling process occurs, a special Euler time independent mesh is applied. By this formulation the mesh has to be generated only once, which simplifies the generation of spatially optimized meshes. For mapping of the material flow during the filling process the method uses a flow surface traction method as applied in casting simulations. A further strength of the new method is the computational efficiency which allows the modelling of extrusion process with the highest complexity with a response time of 12 hours, which is important for the industrial optimization process.

Jan 1, 2015

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By K. Miao, W. Mu, M. Sharma, A. Haas, N. Dogan

"The ever increasing demand for cleaner steels with low inclusion content has highlighted the limits of our current knowledge for controlling and predicting inclusion agglomeration and removal during liquid steel processing. Key knowledge gaps in this area result from the complex nature of the problems associated with measuring and visualizing the phenomena studied. Confocal scanning laser microscope (CSLM) allows for continuous in situ observation of micron-size samples in real time, at high resolution, under conditions relevant to the steelmaking process. This paper summarizes some of recent CSLM applications in our laboratory to illustrate the methods of analyzing transient behavior. The reaction between inclusions and slag is given as an example. The dissolution rate of calcium aluminate inclusions in CaO-SiO2-Al2O3 slags has been studied at elevated temperatures: 1500, 1550 and 1600°C as well as thermodynamic/kinetic analysis. It is found that total dissolution time decreased with increasing temperature. The rate limiting steps are discussed. It is shown that the diffusion through a product layer is responsible for dissolution at 1500°C. At higher temperature, dissolution is most likely controlled by both boundary layer diffusion and chemical reaction at the slag-inclusion interface. In this paper, the evidence for and against the theory will be critically examined and repercussions of the theory to steel refining processes will be discussed.INTRODUCTION Inclusion formation during liquid steel refining is an unavoidable consequence of current ladle steelmaking processes. The nature and quantity of the inclusions formed in steel is critical in steelmaking, as it affects both productivity through clogging, and downstream physical properties of the steel. It is therefore crucial to better understand and control the formation, agglomeration and dissolution behaviour of inclusions in a slag in order to improve the removability of inclusions from liquid steel. Most research (Sandhage & Yurek, 1988; Sandhage & Yurek, 1990a; Sandhuge & Yurek, 1990b; Sandhuge, 1991) relevant to the kinetics of inclusion removal has been obtained by using a technique where simulated inclusion material (ceramic rods) is dipped in slag and the dissolution rate is measured. While much has been learned using this approach, the difference in scale from bulk materials to inclusions is likely to have a significant bearing on the dissolution kinetics of inclusions in a slag and will certainly result in a very different influence of capillary effects. Further, the data obtained using an indirect (dip test) procedure relies on a comparison of the initial and final conditions of a sample rather than in-situ observation which can be achieved in a confocal microscope in real time."

Jan 1, 2017

By A. Blackmore, A. Lamoureux, J. Woloshyn

This paper provides an overview of recent applications of Computational Fluid Dynamics (CFD) to combustion related fugitive emissions problems. The aim is to illustrate the capabilities and discuss the present limitations in this field. Examples include design of retrofitted NOx reduction technology in a kiln and in a boiler, and the prediction of pollutants such as SO2 and metallurgical dust emanating from a copper flash smelting furnace. It is demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause problems and testing solutions, and for concurrently assessing emissions reduction and process impact. In addition, the value of CFD for demonstrating due diligence for regulatory compliance is discussed.

Jan 1, 2015

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By Erik Spiller

"Water and cyanide are highly contentious and conflict issues that many gold mining companies encounter worldwide when dealing with local farming communities, industries and cities competing for water as well as non-government and government organizations. Historically, the gold industry has used processes that required minimum amounts of water to treat and recover gold at locations around the world. Examples are dry grinding for refractory gold treatment in the late 1800s and early 1900s and dry blowing in arid/desert regions to recover alluvial gold. In recent times, new dry processing equipment has been developed and include equipment such as air tables and jigs. Researchers have also modified a Knelson concentrator to concentrate gold from dry solids. High pressure grinding rolls (HPGR) with air classifiers are used to treat industrial minerals and pilot trials have shown that the technology can be applied to comminute refractory gold ores ahead of roasting. Dry stacked tailings is being applied on gold mines to reduce overall water consumption This paper will review the available technologies that in combination may be able to substantially reduce the quantity of water used in the processing of gold ores.INTRODUCTION Water makes up most of the world: the planet is 75% water. Some 97.5% is saline water largely in the oceans, so that only 2.5% is fresh water and useful for human needs. The demand for water is driven primarily by population and concomitant economic growth. Overall, some 70% of the water withdrawn from the environment is used in agriculture, 20% by industry, 7% by households and 3% for mining (Brown, 2003: Maupin et al., 2010). Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Mining activities are often located in remote, arid environments, with limited access to water. There are a multitude of water resources available to the mining industry for its needs. However, much of this water is saline and over the last two decades there has been a continual decline in water quality (i.e. salinity has increased). In today‘s world, there are enormous internal and external pressures to reduce water consumption at a mine, and/or alternatively use water not considered a resource by the local community. Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (i.e. by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing (Dunne, 2010)."

Jan 1, 2017

Despite the fact that mined minerals and gemstones have allowed human beings to continuously improve their standard of living throughout the ages, mining has also been implicated in violent conflict for two principle reasons. The first is that mineral resources have been used or traded to conduct or finance violent conflict from small to large scales. The second is the substantial social, economic and environmental changes that occur in a community or a region as a result of mining activity which can either precipitate or re-awaken latent conflict. A modern complication of mining-related violent conflict is the trend for activists, international NGOs and intergovernmental organisations (e.g. the United Nations) to regard any human consequences of resource extraction in terms of Human Rights violations. Acknowledging but not labouring the Human Rights implications of mining-related violent conflict, this paper explores whether or not there is a relationship between the actual or perceived value of mineral resources and the level of violence that occurs in mining-related conflicts. Key to the investigation is a mapping exercise of mining related conflict from 2005 ? 2012: to see where mining related conflict is happening; to identify precipitant causes of mining related conflict; and, to discover what correlation ? if any ? there might be in the degree of violence and the value of the mineral(s) implicated. Findings of the analysis are presented in this conference paper.

Aug 1, 2013

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities for the nickel industry, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTION The process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic. A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities. These suggestions are particularly applicable to the nickel industry, where the majority of our firm’s prior hydrometallurgical experience was obtained. This paper is an update to an earlier publication (Martin, 2004), offering an opportunity for a new generation of metallurgists and engineers to learn the specialist requirements of pilot- and demonstration-scale plant design, which are key functions in the development and commercialization of new processes."

Jan 1, 2017

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By Y. Tanaka, M. Maeda, S. Suzuki, C. Tokoro, T. Kato, K. Muto

Boron (B) co-precipitation was investigated with ettringite to establish a cost efficient method of removing B from acid mine drainage. For 25 mg/L of B solution, most appropriate pH for B removal was pH 11.5. The most appropriate amount of reagent for B removal within Japanese effluent standard (10 mg/L) was B:Al:Ca:SO4 = 1:3:9:4.5, which corresponds to the composition of Ettringite (Al:Ca:SO4 = 2:6:3). The effect of silicate, carbonate and temperature on efficiency of B removal is important as groundwater and hot spring water are often contaminated. When silicate and carbonate are present, more Al and Ca salts are needed for B removal since some aluminum and calcium precipitate with silicate and carbonate as kaolinite and calcium carbonate. These precipitates do not contribute much to B removal. As the temperature raised, the most appropriate pH for B removal decreased. B removal became less efficient as monosulfate precipitated more rapidly as ettringite.

Jan 1, 2015

By I. Farr, M. R. Mock, J. C. Robison

"HPAL and POX autoclave vapor-space gasses are vented through an autoclave PCV (Pressure Control Valve). The downstream steam-born mist of liquid droplets and solid particles travels in excess of 1000 m/s with megawatts of kinetic power at temperatures up to 160 C. The characteristics of downstream states often result in problems with corrosion, erosion, noise and vibration. Comprehension of those and related characteristics aids in improved pressure control, overpressure control and autoclave level control. We introduce compressible multiphase flow concepts and constructs germane to such flow including choked flow, continuous phase change, shock waves and supersonic flow plumes. Flow modeling based on first principles quantitatively predicts such flows providing a tool for component sizing and a method to estimate effects of water injection on flow. Insight deduced from modeling aids in mitigation of afore mentioned problems of which we share some from-site examples.INTRODUCTION First principles related to fluid thermodynamics and compressible flow have been employed akin to their application in the rocket industry. We will present the results of the application of those principles conceptually and authentically without mathematical rigour while using language of the pertinent disciplines. The autoclave (AC) vapor space over the slurry of a POX (Pressure Oxidation) or HPAL (High-Pressure Acid Leach) system (depicted in Figure 1) is vented via a PCV (pressure control valve) followed by certain ducting, and perhaps a nozzle, before exiting at atmospheric (typically) pressure. As indicated by its name the PCV controls the AC pressure as the flow control component of a pressure control loop."

Jan 1, 2017

By Harry F. Weaver

WHEN 1 was assigned by the Director of the United States Bureau of Mines to present a paper at this annual meeting of the Mining Society of Nova Scotia, 1 was grateful, honoured, and elated to realize finally a life-long desire to see your beautiful land and visit with you who have the good fortune to live and work here. Naturally, in preparing for this important event, 1 wanted to give you something of special interest within the limits of the subject so I chose an area dose to my heart -the operation of our Federal coal mine inspection service, which has, as its fundamental purpose, the prevention of accidents in and around ?Coal mines. In 1957 the United States had 10,879 active coal mines scattered throughout 28 States and the Territory of Alaska. The production of coal for the year was about 515,472,000 tons, including 2.5,472,000 tons of anthracite and 490,000,000 tons of bituminous coal and Hgnite. Anthracite is mined principally in a comparatively small area of one State. AU the 28 States and the Territory produce bituminons coal and/or lignite. The beds mined range from 18 inches to more than 100 feet in thickness and from the horizontal to the perpendicular.

Jan 1, 1958

By Guadalupe Sanchez, Roel Cruz, Sergio Castro, Claudia Beltrán, Isabel Lázaro

The recovery of zinc in refineries is strongly affected by the formation of zinc ferrites during the roasting of zinc concentrates. To achieve the highest zinc recovery most of these plants operate under high acidity and high temperature conditions in their leaching circuits. However, under these conditions high iron dissolution occurs. For iron control the common practice is to precipitate it as jarosite, and calcine is normally used as neutralizing agent. This practice causes a significant loss of metal values associated with the calcine, such as zinc ferrites and silver insoluble phases. These metal values are carried by the jarosite into confined waste in many plants. In order to diminish such losses, it is necessary to use a neutralizing agent that could substitute the use of calcine. An alternative neutralizing could be the basic zinc sulfate (BZnS). This work presents the results of a laboratory analysis on the required conditions for the BZnS production from process streams of a zinc refinery plant. Neutralizing behavior of BZnS was evaluated in iron precipitation as jarosite, in order to establish the feasibility of replacing the calcine and decrease the loss of zinc and other metals values during the iron removing step of the hydrometallurgical circuit of the zinc refinery under study.

Jan 1, 2014

By V. Prasad, A. Afacan, K. Popli, S. Dubljevic

Froth flotation is one of the most common and widely used separation processes in the mineral processing industry; however, its complexity means that complete understanding of the process has not yet been achieved. A dynamic fundamental model is needed to enhance the understanding of the process and to improve process control. It is challenging to capture all the phenomena involved; hence, we propose a multiscale modeling approach with a framework ranging from macroscopic (equipment scale) to microscopic (attachment, detachment) models along with distribution models for ore particle sizes. Real-time froth properties are obtained using a vision-based sensing system. These measurements can be used for developing a soft sensor for grade using statistical methods such as PCR (principal component regression) and PLS (partial least squares) regression. The fundamental model is updated in real-time using extended Kalman filtering. Attachment dynamics are studied for different particle size distributions. The modeling and soft sensing is tested on batch flotation cell for the pure mineral galena with different particle size distributions using Xanthate and MIBC as collector and frother, respectively. The model, online measurements and soft sensor are useful in developing monitoring methods for froth flotation.

Jan 1, 2015

By C. Piribauer, E. Feichtenhofer, A. McEneaney

"As part of a major diversification project, RHI AG, through its plant in Drogheda Ireland, has developed a Caustic Calcined Magnesium Oxide (CCM) for use in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry. In the course of the project, the company investigated the chemical and physical properties of a number of different Magnesia’s used in Co & Ni hydrometallurgy applications and has been able to determine the important parameters for a successful Magnesia for this application. A number of live plant trials have confirmed the results of this testwork and the company is now proceeding to produce this product in commercial quantities at Premier Periclase Ltd., the RHI AG plant in Drogheda, Ireland. This paper will outline the development work conducted by the company and highlight the important chemical and physical properties that make a successful CCM. Much of the research was conducted at the RHI Technology Centre in Leoben, Austria. In addition, a number of external laboratory studies were conducted on behalf of RHI AG. The result of this work has allowed the company to develop a Magnesia product with optimised properties for use in the Cobalt and Nickel hydrometallurgical extraction process.INTRODUCTION Premier Periclase is part of RHI AG, a globally operating supplier of refractory products, systems and services, headquartered in Vienna, Austria. The company produces Magnesia from seawater at its plant in Drogheda, Ireland. While the main focus is on production of refractory grade Dead Burned Magnesia for the steel industry, the plant also produces a number of different grades of Caustic Calcined Magnesia as well as Magnesium Hydroxide products. As part of a major project to diversify the company’s product base, the use of CCM in the Cobalt (Co) & Nickel (Ni) hydrometallurgical extraction industry was investigated. One of the company’s highly reactive grades of Caustic Calcined Magnesia was found to be particularly suitable for this application. In an effort to understand what makes a successful Magnesia for hydrometallurgy the chemical and physical properties of different Magnesia’s used in Co & Ni hydrometallurgy were investigated. This paper and conference presentation outlines the findings of this process."

Jan 1, 2017

By Ainul Akhtar, Steve Cockcroft, Jixiang Xu, Daan Maijer, Lu Yao

"Nitrogen rich Ti-N inclusions are one of the more difficult inclusions to remove during liquid metal refining of titanium. If present in the final component, they can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading. Understanding the kinetics of dissolution of Ti-N particles during consolidation/melting of titanium can help us better operate and design the melting processes to minimize their occurrence in Premium Quality Titanium production. A numerical model based on finite difference method has been developed to calculate the dissolution of a spherical Ti-N particles in molten titanium. Analytical solutions were used to verify the finite difference code for calculation of concentration profile and the dissolution of spherical solids. Taking into account the limitations in these approaches for the different cases examined, the invariant field approximation showed good agreement with the results from the numerical analysis. Evolution of the size of a spherical Ti-N particle during dissolution was predicted by the numerical model and the particle dissolves in 163 s.INTRODUCTION Properties like low density, high specific strength and excellent corrosion resistance make titanium attractive for a variety of applications. Key characteristics in the processing of titanium and its alloys include its high sensitivity to impurities, especially atmospheric oxygen and nitrogen and its high reactivity in the molten state. Nitrogen rich inclusions Ti-N, also known as Type ? or hard alpha defects, usually have substantially higher hardness and lower ductility than the surrounding material. Because they can act as fatigue initiation sites, Ti-N inclusions can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading, even in minor amounts (tenth of a percent) (Lampman, 1990; Moiseyev, 2005; Lütjering & Williams, 2007). Ti-N encompasses as a broad range of nitrogen contents from a few wt% up to stoichiometric TiN. The liquidus temperature of Ti-N titanium increases substantially with increasing nitrogen content. Consequently, depending on the concentration of nitrogen, the melting point of Ti-N inclusions can be above bulk liquid metal temperatures during melt processing. Thus, removal of Ti-N defects hinges on dissolution and not melting."

Jan 1, 2017