Search Documents

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By Ferrin Prince

New Gold?s New Afton mine is an 11,000 tonne per day block caving mine, located 8 km west of the city of Kamloops, British Columbia. The reserve is estimated at 52.5Mt with grades of 0.65 g/t Au and 0.93% Cu. Block caving requires a considerable amount of infrastructure development before production can begin. Each excavation had its own challenges, often further complicated by interactions with the caving stresses and fault structures. The main areas of interest were: the production crusher complex, the surface to underground infrastructure, and the footprint interaction with the faults. The ore zone at New Afton is bounded by two very weak fault zones, with large fault affected areas and associated splays. The resulting rock mass rating (RMR) is 35-50, with some areas significantly weaker due to clay infill. These conditions created a unique and decidedly difficult environment in which to develop New Afton?s infrastructure. Despite these difficulties, the mine began production on schedule in July 2012. The main production crusher for the mine is a gyratory crusher that allows for direct truck dumping, with a smaller jaw crusher in series to facilitate the initial development and production. The crusher chamber was redesigned several times to minimize the chamber volume, resulting in a 40% decrease in volume without losing functionality. After drilling and geotechnical testing, the location of the crusher was changed to eliminate the threat of fault affected ground in the area; the entire complex moved a short time before mining began on the chamber. The mining techniques used enabled tight control of the crusher pocket excavation, while also allowing for the timely completion of the chamber. The locations of the surface to underground infrastructure were tightly constrained by geology, surface infrastructure, and an existing open pit. The VR5 raise was drilled and abandoned part way through the reaming process when the drill string became stuck in fault gouge material. It was relocated and successfully completed. The VR7 raise hit a region of poor rock strength and deviated more than 11 m. Poor ground conditions caused a 130m section of the raise walls to fail. An innovative rehabilitation program was undertaken to re-establish the raise for ventilation. A surface to underground slick line was also installed to ease the material movement underground. A layout of the Extraction level was changed from herring bone to straight through drawpoints that resulted in a net reduction of 1.3 km of development. The Apex level was added to aid in the breakage over the major apex pillar and allow for geological mapping. A portion of the caving footprint is located within the footwall fault. The low strength, high clay content, and small joint spacing of the material resulted in blast-hole cut-off and drift deformation. Drift rehabilitation was a key factor in the successful development of the cave footprint. Innovative drilling and loading techniques were used to keep the holes open and to impede movement along the joint structures.

Aug 1, 2013

By Robert Cameron, Colin Ashton, John MacNeil, Leo Piciacchia

"The in pit dam construction and utilities relocation, known as the East Mine Corridor Relocation (EMCR) project, was developed to extend the life of the east side of the Base Mine pit by two veal's. This will result in the recovery of an additional 80 million barrels of oil and delay expenditures associated with the opening of the North Mine by two years. To accomplish this, a large in pit earth structure was required to provide a new embankment foundation for relocating a public highway, four powerlines, a natural gas back-up pipeline, a substation, and a conveyor train. This structure would also he required as a temporary dam 10 contain mature fine tails on the west side until mining is completed in the east mine corridor area, that will then be filled with fluid.The in pit dam, known as The Highway Berm, is 2.5 km long, 63 m high and has 42 million m3 of engineered soil added to the already existing end-dumped soil volumes. To complete the design and construction of a structure of this magnitude, in the very short time frame of two-and-a-half years, presented many new challenges. The main challenges faced were: designing while construction was ongoing; designing without the use of clay cores or sand filters; using relatively non-select overburden material; proper dewatering and base preparation; changing from construction of 50 m high spoil piles to a high specification construction operation; compacting lifts with heavy haulers; constructing during the winter; and monitoring movement of the structure with satellites."

Jan 1, 1995

By A. E. Boudreau

It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydro thermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward-migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By Li. L.

Backfilling has become a popular solution in underground mines around the world. It reduces environmental impact of mining industry and improves ground stability. In most cases, backfill has a high water content so that it can be delivered by pipes from a backfill plant on ground surface to underground stopes. Upon deposition in the stope, the backfill tends to consolidate under its own weight, leading to a generation of excess pore-water pressure. To avoid excessive pressure and protect the backfill barricade installed at the base of the stope, the backfilling of the stopes is usually divided into two stages: plug pour and backfill body pour. The interruption of backfilling operation is undesirable as it slowdowns the mining productivity, and sometimes causes pipe clogging, leading to unexpected increase in manpower cost and further reduction in mining productivity. The backfilling interruption time may be reduced, even eliminated if the drainage of backfilled stopes is sufficiently improved. This paper presents an application of wick drains, a material commonly used in civil engineering, to mine backfilled stopes to help accelerating the drainage. A protocol is proposed for installing the wick drains in a mine stope to be backfilled. Numerical simulations were made, showing that the drainage of the backfill can significantly be improved by the introduction of wick drains. The application of wick drains in mine backfill can thus be considered as a promising technique and merits deeper and more detailed investigation.

Aug 1, 2013

By Denni Hoffmann

"Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa, were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, AI, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/AI, SilFe, FelMn, LalCe and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnetand amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By Garston Blackwell

Abstract - During geostatistical estimation of block grades, the kriging process produces a measure of error, the kriging variance or the kriging standard deviation. Estimation of the block error depends on the semi-variogram model for a deposit, which reflects fundamental characteristics of a deposit such as (1) nugget effect, (2) range of influence of grades, (3) different local spreads of data as a function of average grade (proportional effect), (4) nested structures, and (5) underlying anisotropies in the data; this model may be affected by sampling or assaying limitations, however. Because the kriging error incorporates so many features of both the deposit and data to be used for estimation, it may offer a substantial improvement on block classification over traditional procedures such as data density. Practice indicates that the relative kriging standard deviation (RKSD) is particularly useful for block classification in measured, indicated and inferred categories. Plots of RKSD in plan and section also can be used to demonstrate where extra drilling and sampling would be most advantageous for upgrading the class of some blocks. Moreover, the use of grade and RKSD filters can show where material near cut-off grade is poorly defined, indicating sampling target areas to improve block classification in the vicinity of the ore-waste boundary.

Jan 1, 1998

By Nitin Bhavsar, Kaushik Vakil, Lakshmikanth Reddy, Sanjay Sarkar, Tathavadkar. Vilas, Bhavin Desai, Raghavendra Adiga

Gold and platinum group metals (PGM) do not dissolve in sulfate electrolyte from anode during electro-refining of primary copper. The PGM form solid ‘slimes’ which accumulates at bottom of the electrolytic cell. Typically, 8 to 10 ppm silver is present in copper cathodes, which is equivalent to almost 2% of silver loss during electro-refining. The silver can be cemented with cathode copper as soon as it is dissolved into the electrolyte from anode or during entrapment of slime particles in cathode. Over a period of time, the concentrates grade has deteriorated and change in type & amount of impurities in concentrate has resulted in higher silver loss during refining process. Therefore, an in-depth investigation was carried out in both fire- and electro-refining processes to understand the root causes of higher silver loss in copper cathodes. The detailed characterization and the plant data analysis were carried out. The results of study revealed that higher silver loss in 3rd crop cathodes as compared to 1st and 2nd crop cathodes from same anode. In anode silver was present in two forms, dissolved in copper (solid solution) and in slime phases such as Cu2-xAgxSeTe. SEM-EDX study of anode cross section confirmed higher silver and oxygen content in central region (core) of anode as compared that in both air and mold sides. This is due to non-uniform cooling of anode which was confirmed by the solidification modeling. Higher concentration of oxygen & silver at core of anode rised Ag+ concentration in electrolyte and slime particles during 3rd crop. The results of study were used to optimize the anode cooling process and also electrolyte chemistry to reduce the silver loss. The details of study carried out are discussed in this paper using the results of modeling, characterization and experimental studies. INTRODUCTION In the electrolytic refining of copper, fire refined copper anodes are used as raw material. Anodes contains copper of the range 99.5 to 99.6%, rest being the impurities. Hence, the purpose of the refining is (1) to remove the impurities so that final cathode conforms to the LME specifications and also (2) to recover the precious metal from the anode copper. When anode is dissolved, most of the impurities reports to the anode slime settled at the bottom of the cell, and rest dissolves in the electrolyte. Dissolved impurities remains in electrolyte and are removed during electrolyte recycling. However, sometime dissolved impurities and slime particles get entrapped in cathode due to disturbances in operational conditions. Metals dissolving in the electrolyte are the elements such as Ni, Co, Fe, Zn. The electrode potential of As, Sb and Bi being close to that of copper, these elements partly dissolve in the electrolyte. Noble metals like Ag, Au, Pt and Pd are generally insoluble and are thus expected to report to the anode slime. A small amount of the sliver content from the anode is dissolved in the electrolyte. Because the dissolved silver electroplates on the cathode at a smaller applied potential than copper, the cathode typically contains up to 8 ppm of silver. This is referred to as ‘silver loss’ in cathode (Cooper, 1987). Fortunately, silver is a rather benign impurity in copper due to its electrical conductivity being higher than copper. However, higher silver loss in cathode is loss of revenue for Copper smelter due to significant difference in their LME price.

Jan 1, 2019

By P. K. Kaiser, D. D. Tannant

"A support system for large ground convergence conditions or burst-prone ground must contain holding elements (rockbolts, cable bolts, etc.) that are strong yet capable of sustaining large deformations, i.e., they must absorb as much energy as possible. Steel wire rope anchored in a borehole by a friction bolt provides these desired yield characteristics if the frictional anchorage is placed deep enough into the rockmass, i.e., in non-yielding rock or beyond the expected depth of rock ejected during a rockburst. Pull-out tests were conducted on wire ropes anchored by inflated Swellex bolts to assess the feasibility of this support concept. The test results demonstrate that a Swellex bolt generates a frictional anchorage that allows the wire rope to slide at high loads and to absorb significantly more energy than either a Swellex bolt alone, or a cement-grouted cable.The rope/friction bolt combination can be engineered to provide the desired energy absorption and allowable deformation by varying the installed lengths of the friction bolt and the rope. For yielding rope support, the contact length between the rope and Swellex bolt must be short enough to ensure that the rope can slip well before its tensile capacity is reached. A safe maximum overlap length is about one metre for the wire rope used in this testing. When used as support in the backs of drifts, a swaged button on the ropes end must be used to ultimately mobilize the full rope capacity thereby protecting against gravity-driven falls of ground."

Jan 1, 1995

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

By D. A. MacFadyen, J. J. Brummer, C. C. Pegg

"The first record of a kimberlite found in Canada (1946) was the identification of thin dykes intersected while drilling for gold in Michaud Township, Ontario.Sampling of the Munro Esker (1964) in the Kirkland Lake area, Ontario, by the Geological Survey of Canada identified the occurrence of detrital grains of pyrope garnets along a length of 35 km of the 113 km tested. A search for the source of the garnets resulted in the identification (1968) of a narrow subsurface kimberlite dyke in the Upper Canada Mine. This discovery resulted in a staking rush. Unfortunately, subsequent work did not identify the source of the kimberlite indicator minerals.During 1978 the Ontario Geological Survey started a multi-discipline study of 29 townships (2560 krn2) in the Kirkland Lake area, to encourage exploration for gold, base metals, and kimberlites. Back-hoe sampling (1979 to 1982), where the overburden was thin, and reverse circulation drilling, in areas of thicker drift, yielded samples of the till. These were analyzed for several elements and a mineralogical identification of the heavy minerals was completed. Pyrope and chrome diopside grains were identified.Studies of the Pleistocene geology indicated only the most recent direction (167 degrees) of ice advance (Matheson) and the associated deposits, out of a possible three advances known to occur in the general region straddling the Ontario-Quebec boundary, is present in the immediate area of Kirkland Lake. Contouring the distribution of pyrope grains (1990) showed a concentration centered over an area of 616 km2 extending down-ice from Gauthier Township. This included a smaller area containing chrome diopside grains. Kimberlite boulders were identified (1981) in gravel pits on the Munro and Misema River Eskers located within this anomalous area. The next step would be to use the airborne geophysical data to locate the kimberlite pipes which yielded the indicator minerals and boulders. The source area is likely to be in the northern half of the Ontario Geological Survey study area."

Jan 1, 1992

By Marta Polgari, Eva Surova, Bohumil Molak

Abstract -The Ûrkút rhodochrosite deposit and Branisko Mn showings (rancieite, manganiferous calcite), located in Lower Jurassic marine sedimentary rocks with black shale, were studied by organic­ geochemical methods. Both depositionallocalities were affected by the Lower Jurassic Toarcian anoxic event. Ûrkút shales are rich in organic matter (av. 2.94 wt% total organic carbon), the composition of which indicates derivation mainly from marine sources, with some terrigenous component. The shales matured in a bacterially active environment under reducing conditions of diagenesis-catagenesis. Branisko shales (?0.2 wt% TOC) with lenses of Mn oxide ore were weakly metamorphosed and their organic matter thermally degraded. The model for Mn carbonate ore formation envisages reaction of Mn derived from sediments, with carbonate generated by a bacterially mediated process of decom­ position of organic matter that also involved Mn reduction.

Jan 1, 1992

By Eva Surová, Molák. Bohumil, Márta Polgári

The Úrkút rhodochrosite deposit and Branisko Mn showings (rancieite, manganiferous calcite), located in Lower Jurassic marine sedimentary rocks with black shale, were studied by organicgeochemical methods. Both depositional localities were affected by the Lower Jurassic Toarcian anoxic event. UrkUt shales are rich in organic matter (av. 2.94 wtOJo total organic carbon), the composition of which indicates derivation mainly from marine sources, with some terrigenous component. The shales matured in a bacterially active environment under reducing conditions of diagenesis-catagenesis. Branisko shales (~0.2 wt % TOC) with lenses of Mn oxide ore were weakly metamorphosed and their organic matter thermally degraded. The model for Mn carbonate ore formation envisages reaction of Mn derived from sediments, with carbonate generated by a bacterially mediated process of decomposition of organic matter that also involved Mn reduction.

Jan 1, 1992

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

"A new method for oxidative destruction of cyanide in industrial waste waters and slurries, such as gold mill barren liquors, tailing slurries and flotation tailings has been developed at the Inca research laboratories. Rapid decomposition of cyanide and related species is attained by treating the waste waters with a mixture of S02 and air at controlled pH and in the presence of a small amount of copper which acts as a catalyst. The approach selectively oxidizes cyanide and metal cyanide complexes, and also removes iron cyano complexes which are not removed by alkaline chlorination.The new method is shown to be less reagent intensive and therefore more economical than alkaline chlorination for treating gold mill and flotation waste waters. INTRODUCTIONOver 90% of the gold mined in Canada is extracted from the ore by ""cyanidation"". Wastes from the process consist of tailings which contain free cyanide, cyanide combined with heavy metals, thiosalts and thiocyanates. Because of the concern over the effect of toxic cyanides on the environment, all cyanide containing effluents will have to be treated in the future to meet certain government set concentration limits."

Jan 1, 1982

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By Robert B. Parsons

"Effective January 1, 1990, mines in British Columbia are subject to a new provincial mining tax statute, the Mineral Tax Act. Under this Act, mines are subject to a two-tier tax system, with a minimum tax payable on ""net current proceeds"" and a higher tax paid on net income. For many mines, the present value of tax paid under the new rules should be comparable to the amount paid under the old rules. Earlier cash payments could pose difficulties, particularly for smaller mines, but existing producing mines could benefit in the short-term.IntroductionEffective January 1, 1990, British Columbia has replaced the provincial mining tax regime under the Mineral Resources Tax Act with a new system under the Mineral Tax Act. The new rules borrow some ideas from other provinces (New Brunswick's two-tier concept, and Saskatchewan's indexed costs) with a view to levying a tax that is fairer to both the producer and the province."

Jan 1, 1990

By K. Reipas

"Westmin Resources Ltd. operates the 3300 TPD H-W underground copper/zinc mine on Vancouver Island. Ore storage underground is handled in a 6000 tonne coarse ore bin and a 3000 tonne fine ore bin. Both of these bins have experienced significant wear since excavation and construction in 1985. Wear problems have included both deteriorating rock walls as well as worn out steel liners and concrete at the discharge points from the bins. Extensive rehabilitation work was completed in 1993.The basis o/this paper is the rehabilitation work done on the coarse ore bin. The design and installation of ground control measures are discussed. The bin access methods used to allow the work to proceed quickly and safely are also presented. This involved the use of a Tekfoam safety bulkhead to protect workers.IntroductionMine DescriptionThe H-W mine was commissioned in 1985. Mine access is by vertical shaft with most production areas at a depth of about 500 m. Host rocks are composed of andesite and rhyolite. Mine capacity of 3300 tonnes per day is achieved mainly by longhole open stoping methods, complemented by room and pillar mining. Metals recovered from the massive sulphide ore are copper, zinc, gold, and silver. Mineable reserves at January I, 1994 were 9.7 million tonnes."

Jan 1, 1995

By D. Neely, D. Milne, L. R. Feldman

"Resin-anchored rebar is commonly used for rock support in mining. The rock properties and environment determine the average bond strength, allowing mine engineers to select the appropriate length and installation pattern for the support. In weak material such as potash, the average bond strength tends to be lower than for a typical hard-rock installation. Determining the failure mechanism by which the support fails in soft-rock applications could lead to improved bond strength and better calculated installed support capacity. This paper reports on research conducted at a potash mine in Saskatchewan and analyzes the failure mechanism of the support.RÉSUMÉ Dans les mines, les barres d’armature enduites de résine sont fréquemment utilisées pour soutenir le roc. L’environnement et les propriétés du roc déterminent la résistance moyenne d’adhésion, permettant ainsi aux ingénieurs miniers de choisir la longueur de barre appropriée et le diagramme d’installation du soutien. Dans des matériaux faibles, tels que la potasse, la résistance moyenne d’adhésion tend à être plus faible que pour une installation typique dans de la roche dure. La détermination du mécanisme de rupture selon lequel le soutien fait défaillance dans des roches tendres pourrait conduire à une meilleure force d’adhésion et à un meilleur calcul du soutien installé. Le présent article fait état de la recherche effectuée dans une mine de potasse en Saskatchewan et analyse le mécanisme de défaillance du soutien. ,"

Jan 1, 2016