Search Documents

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By A. J. Vivyurka

"This is a talk about the experiences that Rio Algom Mines Ltd. has had in the Elliot Lake uranium area trying to make the tailings more compatible with the surrounding environment. To get a better idea of the problem that we are associated with we have to go back to the location. The Elliot Lake uranium area is situated about half way between Sault Ste Marie and Sudbury and is about 20 miles north of Lake Huron. In 1950, uranium was discovered along the north shore of Lake Huron and by 1961 we had up to 9 mines operating in the area. Then the United States Atomic Energy Connnission withdrew their contracts so that at present there are only 2 mines operating. From all the mines that we had operating, we ended up with 7 tailings areas. From these 7 tailings areas we have 5 sites where we have active treatment or rehabilitation. There is the Pronto site where we are treating uranium tailings and copper tailings. There is the Lacnor-Nordic site which is located just out of Ellio Lake. The Milliken-Stanleigh site is in the Crotch Lake area. The Panel tailings is off the north end of Quirke Lake and finally there is the operating property of Rio Algom Mines at Quirke Lake.To understand fully the problem with this rehabilitation we have to look at the constituents of the ore. The ore body is a quartz conglomerate with uraninite and brannerite as the uranium bearing minerals in a fine ground mass of quartz, sericite and pyrite which separates the larger quartz pebbles. The approximate composition of the ore is: 80% quartz, 13% chlorite, 7% pyrite and 0.2% uranium minerals. The processing method also adds a few constituents to the final tailings."

Jan 1, 1975

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987

By D. Kidby, A. Briggs

"Vitrokele ™ is a synthetic adsorbent, using chelating groups on large polystyrene beads, developed in Canada over 7 years ago, and first commercialised in 1985 to recover noxious metals from plating wastes.Pilot plant trials have been performed in Australia and Canada to demonstrate the recovery of cyanide and removal of metal cyanide complexes from gold plant effluent using Vitrokele1 M 912. The pilot plants comprise a simple adsorption train (similar to a CIP circuit) followed by complete elution facilities, so that loaded Vitrokele™ can be stripped and returned to the adsorption circuit.An account of these campaigns is provided, showing the reduction of total CN levels from over 200 ppm to less than 0.5 ppm and Cu levels from approximately 100 ppm to less than 0.3 ppm in treated tailings.Comparisons between pilot plant results and laboratory test data are given and probable future work on the process and its application to the gold mining industry is discussed.INTRODUCTIONThrough millions of years of evolution, life forms have developed specialised molecules with exceptionally high affinity and selectivity for various metals such as iron, cobalt, zinc and copper.In the early 80's professors at the Faculty of Medicine of McGill University engaged in research on the extremely efficient ways that living cells captured trace metals essential for life.As research progressed, it became evident that the special molecules used by biological systems to capture metals could be synthesized to capture selected metals with similar efficiency from water or other solutions.The technology was first commercialised in 1985 to recover noxious metals from plating wastes with compositions applying the special molecules (chelating groups) on vitreous particles (hence Vitrokele™). To date approximately three commercial Vitrokele™ plants have been installed for treating plating waters in Ontario and Quebec."

Jan 1, 1992

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

Located in Timmins, Ontario the Porcupine Joint Venture, a pooling of assets between two existing operations (the Dome Operation of Placer Dome (CLA) and the Hoyle Pond Operation of Kinross Gold Corporation) came about on July 1st, 2002; Placer being the manager of the Joint Venture with 51% ownership and Kinross with 49%. The formation of the Joint Venture was the realization of the dream of many who could envision the benefits of the whole area being operated as one entity ? the combination of the majority of assets in the Porcupine Camp into one venture containing tremendous synergistic potential of manpower, infrastructure, land tenure and exploration development. The name Porcupine in the gold mining industry brings with it the legacy of world class gold mines; the Hollinger, McIntyre and Dome with a proud tradition of excellence. The name Porcupine brings with it the legacy of over twenty individual mining companies in operation at any one time, producing over 65 million ounces of gold.

May 1, 2003

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By G. R. Addie

"In February, 1975, the President of Georgia Iron Works Company, Mr. Tom Hagler decided to build a new hydraulic laboratory to water performance test all of the companies' centrifugal slurry pumps.Equipment procurement started in March, 1975, by ordering of a mini computer data acquisition system.Work commenced on the lab in July, 1976, by erection of a Butler Building and the laying down of a 20,000 gallon concrete sump.By late October, a facility compromising two water test loops of 8"" and 18"" pipe diameter was in operation carrying out head quantity and suction performance tests on pumps up to 16"" in size.In August of the following year, an 8"" diameter pipe slurry loop was installed to enable pipe friction and deposition velocity of a slurry to be measured in an 8"" inside diameter pipe.With the encouragement of Reserve Mining in Minnesota and IMCC in Florida, this was followed in March, 1978, by the addition of over 300 feet of 18"" diameter pipe to make up an 18"" diameter pipe slurry system complete with head loss and deposition velocity observation sections.The office and shop areas of the lab were again expanded in April, 1978, to provide further expansion to the test sections and staff facilities."

Jan 1, 1980

By M. J. McLeod, S. Watters, G. G. Lutes, S. Castonguay

"Gold-bearing mineralization at Anomaly A occurs in polydeformed Ordovician turbidites of the Kendall Mountain Formation of the St. Croix belt in southwestern New Brunswick, and is hosted by WSWtrending, shallow-dipping, brittle-ductile high-strain zones associated with the latest stage of the second of four regional deformation events. Gold-bearing syn-deformational stockwork, massive, and multiply brecciated quartz-sulfide veined zones form irregular pods and sheets up to several meters thick, which contain arsenopyrite, pyrrhotite, pyrite, stibnite, and a variety of rare minerals that are gold-bearing. Mineralized zones are enveloped by locally auriferous, weakly to intensely altered wall rock. Vein paragenesis includes: (1) early (pre- to syn-D2) quartz-chlorite veins that are largely the product of migration of quartz by pressure solution; (2) crosscutting, multiphase, vuggy quartz-sulfide veins that contain most of the gold and are interpreted to be structurally controlled; (3) late, crosscutting, nondeformed, non-gold-bearing veins containing laumontite, chlorite, muscovite, quartz, fluorite, and base metal sulfides. Carbonate-poor alteration associated with zones of gold mineralization is lithology-specific, and appears to reflect overprinting of multiple events. Major elements removed during alteration include Si, Na, Mn, and Mg. The minor and trace elements removed include Co, Li, Sc, and possibly Sr, Ni, and Zn. Minor and trace elements added include Au, Ag, As, Sb, S, and possibly F, Cu, Pb, and Zr. On the basis of proximity, time constraints, and a similar ore mineral assemblage, gold mineralization at Anomaly A is interpreted to be a distal equivalent of the intrusion-related gold mineralization at the nearby Clarence Stream Main zone deposit. La minéralisation aurifère de l’Anomalie A se trouve dans des turbidites Ordoviciennes polydéformées de la Formation de Kendall Mountain, dans la ceinture de Ste-Croix du sud-ouest du Nouveau Brunswick, où elle est contenue dans des zones de déformation fragile-ductile à faible pendage de direction OSO associées au dernier stade du second de quatre épisodes de déformation régionale. Les zones aurifères syn-déformationelles se présentent en forme massive, de stockwork, ou de veines de quartz-sulfure bréchifiées à répétition formant des lentilles irrégulières et des couches de plusieurs mètres d’épaisseur contenant de l’arsénopyrite, de la pyrrhotite, de la pyrite, de la stibine, ainsi que divers minéraux aurifères rares. Les zones minéralisées sont entourées d’une enveloppe de roches faiblement à intensément altérées, localement aurifères. La paragénèse des veines comprend : (1) des veines précoces de quartz-chlorite (pré- à syn-D2) qui sont principalement le produit de la migration du quartz par solution-pression; (2) des veines polyphasées de quartz drusique et de sulfures contenant la plus grande partie de l’or, celles-ci sont considérées comme étant sujettes à un contrôle structural; (3) des veines tardives stériles, sécantes et non déformées contenant de la laumontite, de la chlorite, de la muscovite, du quartz, de la fluorite et des sulfures de métaux usuels. Les zones de minéralisation aurifère sont associées à une faible altération en carbonate contrôlée par la lithologie et semble résulter de la superposition d’événements multiples. Les éléments majeurs perdus durant l’altération sont le Si, le Na, le Mn et le Mg. Les éléments mineurs et traces perdus durant l’altération sont le Co, le Li, le Sc et possiblement le Sr, le Ni et le Zn. Les éléments mineurs et traces enrichis comprennent l’Au, l’Ag, l’As, le Sb, le S et possiblement le F, le Cu, le Pb et le Zr. Étant donné sa proximité géographique, les contraintes temporelles et les similitudes de leurs assemblages minéraux, la minéralisation aurifère de l’Anomalie A est interprétée comme un équivalent distal de la minéralisation aurifère associée aux intrusions du gisement avoisinant de la zone principale (Main"

Jan 1, 2008

By Steve Custer, Tim Kahl, Sue Parker

"The primary objective of the Barrick Goldstrike expert system is to achieve the desired liberation size for the autoclave circuit while maximizing throughput. In addition, when downstream limitations (autoclave circuit or others) restrict the milling circuit tonnage the expert system further improves grinding product size. Since its implementation, the expert system has provided expected throughput improvements while improving or maintaining circuit performance.Barrick Goldstrike and MinnovEX Technologies Inc. teamed up to install an expert system to control Line I and I1 of the autoclave grinding circuits. The dissimilar equipments of the two grinding circuits coupled to different production objectives, skepticism among operators, and the variability of the ore types processed in each line challenged the implementation.To ensure implementation success, Barrick Goldstrike dedicated four administrators full time to the project. The system administrators included two metallurgists, a process control engineer and a mill trainer. As usual, the control room operators were the experts who provided the operational logic for the foundation of the control system. The administrators and all eleven of the control room operators signed off on acceptance of the system. Current online utilization is 95%.INTRODUCTIONThe grinding circuit for Barrick Goldstrike’s autoclave process consists of two SAG Mill Ball Mill lines. Line 1 grinding circuit is comprised of a 22 by 8 foot, 2500 horsepower Allis Chalmers (AC) variable speed SAG mill, followed by a 12.5 by 14 foot, 1250 horsepower AC ball mill, and a 13.5 by 18 foot, 1800 horsepower Dominion ball mill in parallel. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1352 Nordberg Omnicone crusher (4.5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The ball mill circuit is closed with 6 Krebs super D20 cyclones. Line 2 grinding circuit is comprised of a 24 by 12 foot 4000 horsepower Fuller variable speed SAG mill followed by a 16.5 by 30.5 foot 5000 horsepower Fuller ball mill. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1560 Nordberg Omnicone crusher (5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The line 2 ball mill circuit is closed with 12 Krebs super D20 cyclones. The underground Meikle ore is typically fed through Line 1. Achieving the desired product size is critical for successful processing of Meikle ore. Open pit Betze ore is fed to Line 1 when Meikle ore is unavailable. Line 2 processes Betze ore exclusively. Throughput is maximized when processing Betze ore as the product size is less critical. The products of these two circuits are combined as feed to the autoclave circuit. The ore types and the autoclave circuit demands determine the required grinding circuit product size and maximum combined mill feed tonnage."

Jan 1, 2001

By Jennifer Pell

Dunsmuir Ventures? Nanuq diamond project is located approximately 250 km northeast of Baker Lake and 170 km north of Chesterfield Inlet. It occurs at the intersection of the Wager Bay shear zone with the Keewatin Arch, a major long-lived crustal uplift. The newly discovered diamondiferous kimberlites at Rankin Inlet, Repulse Bay and on Melville Peninsula also occur along this arch. Kimberlite indicator mineral (KIM) sampling has outlined a distinct KIM train more than 35 km long and 6 km wide. Geomorphological studies, boulder displacements and dispersion of magnetite in tills suggest that glacial transport distances were on the order of 4 to 6 kms only. The presence of multiple sources within the main Nanuq indicator train would account for its length and breadth. A second train has been located on the west central part of the property and anomalous concentrations of KIM occur elsewhere. Pyrope garnets (G9?s and G10?s), diamond inclusion field (DI) eclogitic garnets and DI chromites were confirmed by microprobe analyses. Clinopyroxene thermobarometry indicates a cool geotherm, approximately 35 mW/m2, and that mantle within the diamond stability field was tapped. An aeromagnetic survey has identified a number of anomalies. Those with down ice KIM support will have ground geophysical follow-up and will be tested in a spring 2004 drill program. Dunsmuir is optimistic that this will lead to the discovery of a new kimberlite cluster on the Nanuq property.

May 1, 2004

By Zhuofei Yang, Jidong Kang, David S. Wilkinson

The fatigue behavior of AM60 high pressure die casting magnesium alloys was studied in a straincontrolled manner. The fatigue test was interrupted every 2,000 cycles for X-ray tomography scanning. The specimen was removed to be scanned on a desktop micro-CT system. The value of using X-ray tomography in a fatigue properties study was assessed with respect to porosity, cracks and fracture surfaces. The 3D analysis and model results showed porosity could be well measured and modelled in 3D. Defects bands are made of pores under 50 µm in volume-equivalent sphere diameter. Larger pores are randomly distributed in the region between two defect bands. Observation of cracks by X-ray tomography occurs in three ways such that the 3D model gives the best illustration of crack-porosity interaction while the other two methods have better detectability on crack initiation and crack tip observation. X-ray tomography is also of value in failure analysis on fracture surfaces. By summarizing X-ray tomography data during fatigue testing and observing fracture surfaces on a 3D model, a better understanding on the crack initiation, crack-porosity interaction and the morphology of fracture surface is achieved.

Jan 1, 2014

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

By Grant Goddard

Cameco?s ?Double U? Strategy ? Double existing production ? To 40 million lbs U3O8 annually ? By 2018 ? Existing operations ? Saskatchewan ? United States ? Kazakhstan ? Projects under evaluation ? McArthur River expansion ? Kintyre (Australia) ? Inkai Block 3 (Kazakhstan) ? Development properties ? Cigar Lake project Measures of Success ? Safe, healthy and rewarding workplace ? Supportive communities ? Clean environment ? Outstanding financial performance

Nov 1, 2011

By Margarete Kalin

"Biotechnological approaches to decommissioning of mine waste management areas are presented in the context of sustainable environmental management. Improved design of waste sites and environmental management paves the way for the application of new technological approaches. Mining wastes are better confined, effluent quantity is reduced and the quality is expected to improve in the future. The biologically mediated treatments focus on the creation of conditions inside the waste management area which lead to the confinement of the contaminants in the inactive tailings ponds and seepage collection ponds, as well as pits or other disturbed areas which were part of the operating conditions.Biogeochemical reactions lead to three fundamental water treatment steps mediated biogeochemically , alterations in chemistry which lead to formation of particles, which then have to flocculate and be assisted to collect in the bottom of the ponds. Microbially active sediments are installed to assist particulate formation and serve as sinks for metals. In deeper sediment strata, stable forms of metals are created. Biological polishing is used to collect the particulates and relegate them to the sediment. Examples will be given of the application of these processes, to waste rock piles, open pits and tailings ponds. This paper attempts to show that, through the integration of applied biotechnological advances and the application of new approaches to decommissioning, reductions of environmental impacts by mining are possible. * Note: this paper has been presented at the 13th Annual Meeting of BIOMINETIntroductionThe role of biotechnology in decommissioning of mining waste management areas should be placed in the context of sustainable development. The concept of sustainable development as defined by the Brundtland Commission (1987) for the restoration/ reclamation of mining operations could be translated as follows: The increasing demand for the resources by the world population must be met in a manner which does not compromise the earth's environment over the long term (Brooks et al., 1995)."

Jan 1, 1998