Search Documents

By Tim Martin, Dave Tahija

"In April, 2014, Hecla's Greens Creek mill, near Juneau, Alaska, switched from sulphuric acid to the use of dissolved carbon dioxide for lead flotation circuit pH control. The Greens Creek mine uses paste backfill, in which mill tailings are mixed with cement and used to fill mined areas. Some backfill inevitably becomes part of mill feed during subsequent mining cycles, resulting in high feed pH levels and increased dissolved calcium in the lead flotation circuit. Sulphuric acid is traditionally used to lower pH in such cases but it produces undesirable side effects, including poorer lead-zinc separation and unstable froth. The amount of sulphuric acid used at Greens Creek was limited due to these effects, resulting in higher than target pHs when feed backfill content was high. Dissolved carbon dioxide can be added without these limitations so pH levels have been under much better control since the switch. Additionally, lead-zinc separation and froth characteristics have significantly improved.IntroductionThe Greens Creek Mine, owned by Hecla Greens Creek Mining is an underground mine located on Admiralty Island near Juneau, Alaska, producing silver, gold, lead and zinc in the form of lead and zinc flotation concentrates and a gravity gold concentrate (McDonald, Morgen & Hancock, 2012). The lead and zinc concentrates are produced in conventional flotation circuits preceded by a graphite removal flotation step.The underground mine utilizes cemented paste backfill, of which a certain amount is inevitably re-mined in later mining cycles and returned to the mill, mixed with fresh ore. The Portland cement used in the paste backfill is highly basic so that, from the point of view of the mill, the net effect is to introduce a good deal of lime to run-of-mine mill feed, producing a very high natural pH. This high pH needs to be lowered to obtain good metallurgical results."

Jan 1, 2016

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By K. D. Mills, R. G. Robins, C. G. Anderson, L. G. Twidwell

Arsenic is a metalloid which has attracted great environmental scrutiny in recent decades. Moreover, its control and deportment is becoming increasingly important in the metallurgical processing of modern complex ores and concentrates. As such the authors of this publication have a combined professional experience of well over 100 years in the study and hydrometallurgical treatment of arsenic. Hence, this paper will cover arsenic fundamentals along with a review of technology for removal, fixation and stabilization. Finally, an application of industrial Alkaline Sulfide Leaching (ASL) of a copper enargite concentrate will be elucidated.

Jan 1, 2014

By E. W. Johnson

"The title of my paper is ""I 'Wonder Where The Yellow Went"". As you can readily guess, it is not related to an old-fashioned ""Pepsodent"" sales pitch! Rather, it concerns a situation which arises all too frequently in some gold milling operations, namely when actual ounces of gold production do not come up to estimated or projected ounces. The boss man scratches his head and wonders where the missing gold has gone and how it has disappeared. The problem, if one exists, is amplified if one forgets that an estimate is just that - an estimate - and not a hard fact - even though the numbers are produced by computers. And yet, from the point of view of engineering; financial and production planning and security; it is most desirable to tie together all data relating to production estimates, losses and actual production.In the course of this paper reference will be made to the term ""variance psychology"", to a few of the physical properties of gold and to the nature of its occurrence in Canadian ores, in relation to the topic under consideration. Activities which have a bearing on production estimates will be reviewed. These include: weighing, sampling, assaying, estimating residual losses and, in cyanide plants, gold precipitate production. Mention will be made of apparent, unaccounted for and unknown losses. In conclusion, I shall draw from personal experience and relate three examples of ""Where the Yellow Went''."

Jan 1, 1986

By G. Taylor

"The Iron Ore Company Of Canada's Carol Project is located in Labrador City, Newfoundland. Labrador City is some 912 air kilometers northeast of Montreal, and 417 ratl kilometers north of Sept-Iles, Quebec.Over 2,800 employees work at the Carol Project to produce some 20.0 million tonnes of concentrate and 10.5 million tonnes of pellets annually.In 1979 our Training Department started to develop the DACUM System of training for our Concentrator Operations Department.DACUM is an individualized, self-learning, training program. It is both a curriculum plan and an evaluation instrument.To date, the DACUM System has been completed for all occupations in the concentrator and work will commence shortly to develop DACUM for our Pellet Plant and Mine Operations Departments."

Jan 1, 1982

By A. R. Barnes, N. O. Lotter

Recoverable economic copper sulphide minerals such as chalcopyrite, bornite, chalcocite and covellite often occur together in varying proportions in the major copper-bearing ores, and have individual flotation requirements and characteristics. Pyrite also occurs in these ores to varying extents as the sulphide gangue, and is problematic because of its natural tendency to float quickly and easily. In a bulk sulphide float, selectivity against pyrite is desirable, particularly if it does not host other paymetals such as gold or silver. At the same time it is a requirement to float all of the copper sulphides despite their electrochemical differences. The electrochemistry and semiconductor properties of these minerals are reviewed, together with implications for flotation with and without collector addition. Mixed collector systems for the improved flotation of these sulphides are proposed as a solution. The use of xanthate and dithiophosphate in the collector suite allows the co-existence of dixanthogen and free dithiophosphate radical because the latter has a higher redox potential requirement than xanthate to oxidise to the dithiolate. Because some of these minerals require dixanthogen, and others, free thiolate, to generate surface hydrophobicity, a bulk flotation of all the species becomes possible in the overlapping area of Eh and pH between the two dithiolate equilibrium lines on the Pourbaix diagram. The arsenic-signature copper minerals are added to the study, since many copper operations encounter arsenic as a penalty element in the saleable concentrate. It is shown that the addition of arsenic to the copper and iron sulphides alters the semiconductor and electrochemistry properties, and in turn, its flotation characteristics. The degree of mineral association and liberation between these minerals can be a complicating factor due to textural associations, and should also be considered in the process as a next step.

Jan 1, 2016

By S. Stefanizzi

In the present paper, numerical simulations based on a finite/discrete element approach are used to study deformation and failure process during standard rock mechanics. FEM/DEM modeling has been used as available with the ELFEN code, which explicitly model the transition from continuum to discontinuum. The transition is simulated through a crack nucleation and propagation that obeys to the Griffith?s failure criterion. If the fracture criterion within the intact rock (represented by FEM) is met, a new crack (represented by DEM) is initiated. Remeshing allows the fracture process through the FEM mesh to be tracked and visualized, thus contact properties can be assigned to pre-existing fractures and newly generated fractures. In this study, compressive tests of rock samples are simulated. The applicability of ELFEN to properly and efficiently simulate typical laboratory rock mechanics tests, with reference to the rock fracture process, is described in detail. In addition, an indirect validation of the extensional strain criterion proposed by Stacey (1981) is given.

May 1, 2009

By James R. Lang

The Xietongmen deposit is located 350 km west of Lhasa, Tibet. It is a new, high-grade porphyry copper-gold discovery and the first deposit to be systematically explored by a western company in southern Tibet. In 2005, Continental Minerals Corporation drilled 21,332 m of core in 63 holes and demonstrated excellent lateral and vertical continuity of high-grade copper-gold mineralization over an area 750 m by up to 350 m in size which remains open in all lateral directions. Drill intersections repeatedly yield grades >1% Cu equivalent (based on gold and copper prices) and include 308.5 m at 0.87% Cu and 1.25 g/T Au (1.60 CuEQ%), and 315.6 metres at 0.61% Cu and 1.11 g/T Au (1.26 CuEQ%). Extensive drilling in 2006 will expand and delineate the deposit, and metallurgical, engineering, environmental and socio-economic evaluations will begin. Xietongmen is hosted by volcanic and intrusive rocks of the Gangdese belt, a magmatic arc active between 120 and 30 Ma along the southern margin of Eurasia. Pervasive alteration is dominated by a well-mineralized K-feldspar and biotite assemblage, and by a more peripheral sericitic assemblage also with strong chalcopyrite. Major vein stages include chalcopyrite-bearing quartz, biotite, magnetite and pyrite-pyrrhotite types.

May 1, 2006

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By A. Dogan Paktunc

Abstract - The Mechanic Settlement pluton is a small body of mafic and ultramafic rocks of tholeiitic affinity, occurring in the Late Neoproterozoic volcanosedimentary rocks of the Avalon terrane of the Appalachian Orogen. The lenticular-shaped intrusion is layered and consists of ultramafic and mafic lithologies in at least six cyclic units that are relatively thin or short-lived. The lowermost exposed portion of the intrusion is characterized by the cumulate sequences of olivine and olivineclinopyroxene and display relatively flat rare earth element profiles. In the overlying lithologies, plagioclase is the dominant cumulus phase following olivine in the crystallization sequence. Olivine ranges in composition from Fo73 to Fo85 and plagioclase from An62 to An89. Variations in the compositions of orthopyroxene and clinopyroxene are within Wo0-4En52-87Fs11-45 and Wo39-50En23-50Fs3-19. These mineral compositional variations in part reflect cryptic patterns and correspond to normal fractionation trends in cyclic units. Elevated Pt and Pd concentrations of up to 2.6 ppm occur in ten zones within the central cyclic series in association with both the peridotitic and gabbronoritic rock types. The mineralized zones are about several meters thick and appear to have lateral continuities over several hundred meters, suggesting that they are stratiform. Platinum-group elements (PGE) occur as discrete platinum-group minerals (PGM) including vysotskite, merenskyite, michenerite, sperrylite, stillwaterite, and hollingworthite that are associated with magmatic sulfides composed of pentlandite, pyrrhotite, and chalcopyrite. PGM grains range in size from a few micrometers to well above 20 µm. Sulfur isotope ratios and the Se/S ratios of the mineralized rocks are typically higher than the mantle values. Sulfide saturation probably occurred as a result of assimilation of crustal rocks and magma mixing during emplacement of subsequent pulses of magma. Repetition of the PGE mineralization in rather thin cyclic units suggests that the replenishing magma probably had high PGE levels and was saturated with respect to sulfide during emplacement. Ingression of the replenishing magma into the chamber in a turbulent plume and its mixing with the resident magma was probably responsible for the formation of the PGE mineralizations in the Mechanic Settlement pluton.

Jan 1, 2000

By Brad E. Melanson

Because mine haul trucks consume considerable quantities of fuel, they are ideal candidates for the adoption of cleaner and cheaper fuels like natural gas. Impressive fuel cost savings will be realized in regions where liquefied natural gas (LNG) has cost advantage to diesel fuel, while also providing significant reductions of air contaminants and greenhouse gases. High Pressure Direct Injection (HPDI) of natural gas utilizes the diesel cycle combustion process and therefore retains the diesel engine?s high performance and efficiency characteristics. HPDI has been demonstrated in on-road Class 8 trucks since 2001 accumulating almost 10 million kilometres to date. The supply of LNG fuel will be an essential parallel aspect in the introduction of HPDI to mining. LNG can be transported to site as diesel is today, or may be produced on or near mine operations that have access to methane sources or pipelines.

May 1, 2006

By F. Flynn, P. Downey, G. Ritson

"Bell Creek Mill which has been in continuous operation since 1987 has undergone numerous operational changes in the past three years. The addition of over 2. 5 million tons of resource at over 13 git from Hoyle Pond Mine precipitated an expansion program for the Bell Creek Mill. This paper discusses the major changes that have occurred over the past two years to increase throughput and efficiencies. In addition, the refractory ore treatment options are also discussed.IntroductionThe Bell Creek Mill is located in the Timmins Goldcamp approximately 8km NE of porcupine Ontario. (Fig I.)The mill was originally constructed by Camamax in 1987 to treat the Bell Creek ore at a design throughput of 350tpd. The flowsheet (Fig 2.) consisted of two stage crushing, grinding, thickening, leach and drum filtration with gold recovery by Merrill Crowe.As ore depleted at Bell Creek, the Mill was purchased by Falconbridge to process ore from their Hoyle Pond property. Kinross purchased the Hoyle Pond property and Bell Creek Mill from Falconbridge in 1992.The successful exploration program at Hoyle Pond has led to several expansions and process design changes, with further changes planned over the next twelve months.In 1994, the mine produced 61,865 oz. of gold at an average cost of 197US$ per oz. In 1995 production was 91, 611 oz. at a cost of 187US$ per oz. Projecting the nine months ended September 30, production for 1996 will be 155,000 oz. at a cost of 165US$ per oz.In early 1997, the CIP expansion will be complete, with a target of 175,000 oz. at a cost of 176US$ per oz for 1997. The mill throughput will have increased from 400tpd to 1500tpd between 1994 and 1997.The changes to Bell Creek since 1994 have been numerous with very little of the existing equipment still in operation. The total cost of the expansion to date is 15 million C$. This paper discusses the major projects carried out during in this time. The focus will be to highlight the justification of each project, the design and engineering, some of the initial start-up problems and solutions.Figure 3 shows a plan of the existing mill facility together with the various additions that were carried out."

Jan 1, 1997

By A. Ignatieff

"Demonstrations of Automatic Coal Burning EquipmentAT THE 1951 and 1952 Annual Coal Research Conferences sponsored by the Dominion Coal Board and attended by delegates from the Dominion and Provincial governments as well as industry, the importance ,of encouraging the co-operative interest of Canadian coal and equipment industries in •promoting the use of equipment types best suited to burn given Canadian coals was emphasized. It. was suggested that this idea •be enlarged upon at forthcoming C.I.M. meetings that would be .attended largely by coal mining engineers.With this in view, a Domestic Heating Forum (1) was featured in the Coal Division programme at the 1951 Annual Western Meeting of the Institute in Calgary, and a much more ambitious programme, highlighted by live demonstrations, was •staged at the combined Annual Western Meeting and Fourth Meeting of District 4 held in Winnipeg in October 1952.With the excellent co-operation of a number of equipment manufacturers and coal companies, and with facilities kindly provided •by the University •of Manitoba authorities, burning demonstrations were• arranged in the Agricultural Engineering Building, on October l 7th. These demonstrations were a fitting sequel to the Coal Division sessions held in the Royal Alexandra Hotel on October 16th, at which the combustion of coal was specially featured in a series of papers by prominent Canadian and United States specialists.The primary purpose of the demonstrations was to •show that all coal, regardless •of rank, can be satisfactorily used provided that proper application is made with equipment suited to its purpose."

Jan 1, 1953

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By J. Keith Haddock

"Introduction The Luscar company, Forestburg Collieries Ltd., operates the Diplomat Mine located 14 km south of Forestburg, Alberta. Production is now at a declining rate from the 1 million tonnes achieved in 1978 as the reserves are being depleted. Three pits are operated at this prairie strip mine utilizing draglines and stripping shovels to uncover the coal. The coal is hauled to a tipple on site for shipment by rail or highway vehicles or is hauled directly to the adjacent Battle River Generating Station. Geology The mine is currently extracting the Battle River seam on the north side of the Battle River. This is the lower-most seam in the Horseshoe Canyon Formation and is the only one present in the area, the upper seams having been eroded by glaciation. The seam lies generally flat and varies from 2.0 to 5.0 metres thick. It lies under glacial till overburden varying in depth from 5.0 to 12.0 metres. The mineable coal extends from the side of the Battle River valley where it outcrops, to approximately 2.5 kilometres to the north. The mine is spread out over a distance of 8.0 kilometres in an east-west direction. Reserves and Coal Quality After over 30 years of mining at Diplomat, there are now less than 1 million tonnes of mineable reserves remaining on the property. With the commencement of coal production from the Paintearth Mine in 1981, supply to the Battle River Generating Station, formerly Diplomat's biggest customer, is being transferred to Paintearth. Rail shipments and domestic supply will continue until reserves are depleted. The coal has the following specifications:"

Jan 1, 1985

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013