Search Documents

The Olympic Dam copper-uranium-gold-silver deposit, located approximately 520 km north-northwest of Adelaide, South Australia (Figure 1) was discovered in 1975 by Western Mining Corporation. A joint venture to facilitate development of the deposit was formed in mid-1979 between WMC (51 per cent) and the British Petroleum Group (BP, 49 per cent). Production commenced in 1988, and current annual output from the mining and treatment of 2.2 Mt of ore is approximately 65 000 t of refined copper and 1400 t of uranium oxide. Significant amounts of refined gold and silver are also produced.

Jan 1, 1993

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

By T Higuchi, T Yamamoto, K Takehara

Iron ore fines are used as raw materials for sintered ore for blast furnaces in the world. Since the production and quality of sintered ore have a great influence on the stable operation of a blast furnace, many technologies were developed for controlling the heat profile in the sintering machine, which largely affect the sintered ore properties. In particular, the influence of oxygen in the suction gas, which plays an important role in combustion, was investigated over the years. It is known that increasing the oxygen ratio by about 30 per cent not only significantly improves the combustion rate, but it also increases the strength and yield of sintered ore. However, the details of the mechanism for improving these qualities are unknown. In this study, we investigated the influence of oxygen enrichment at higher ratios (O2: 21–40 per cent) and tried to understand the sintering behaviour enhanced by oxygen. The effect of oxygen enrichment on sintered ore quality and the heat profile were evaluated by sintering tests using a quartz glass pot. From the results, sintered ore yield had a maximum value for O2 = 30 per cent, but strength was increased for O2 = 40 per cent. From heat pattern analysis, it is clear that the high temperature holding time also reached a maximum at O2 = 30 per cent. Furthermore, we found that with increased oxygen ratio, the combustion speed (flame front speed) was increased, but the area of combustion was enlarged. It is considered that there could be a maximum oxygen ratio value for the yield from the balance of these positive and negative effects on high temperature holding time. To clarify the reason for strength improvement, thermodynamic calculations were performed and it was found that melting behaviour could be improved by changing the oxygen ratio.

Sep 18, 2023

In Finland fogging in mine ramps is a common problem. Fog forms when warm and humid exhaust air moves upwards the ramp, where the skin temperature of surrounding wallrock decreases to about 10¦C. Changes in fog thickness and lengths of fog-filled parts of the ramp depend at least on climatic conditions outside, diesel equipment usage in the mine, and the length of working sequence at a time. In this study fogging problems in three different mines, namely Orivesi mine, Louhi mine and PyhSsalmi mine, with different ore types, different layouts, and different depths are presented and compared. All these mines use diesel equipment and the ramp is used as an exhaust air route. In two of these mines the ramp is used as a haulage road and in the other for supply and repairing, checking, and surveying purposes. Measurements of humidity, temperature, air velocity, and dust content were performed in these mines. The measurement results, as well as field observations are presented, compared, and discussed. The results show that fog is observed in areas with high relative humidity values when air temperature and dew point temperature are less than 3¦C apart from each other. Air velocity values were high in many areas. In addition, measured particle concentration values were mainly high in areas, where fog was observed. A short literature review of recent fog formation studies is also presented. It demonstrates the complicacy of the fog formation process. Similarities and differences concerning fog problems in the ramps are found and presented. As already a lot of new information is gained, the continuation of research is considered plausible to find more economical ways of solving and preventing this problem in the future.

Jan 1, 2005

The GDR has extensive lignite deposits at its disposal, which formed the basis for the development of an independent energy source after 1945 and which will retain their significance well beyond the year 2000 (see fig. 1). In 1946 lignite output was about 110 x 106 t. In 1985 312x 106 t was produced and in 1988 the planned output will be ca. 315 x 106 t. Thus, the domestic produc- tion of lignite covers ca. 75% of the GDR's primary energy requirements. More than 80% of the electrical energy is gener- ated by the use of lignite and about 12% by nuclear energy. In addition to this, about 18 x 106 t/a mineral oil and about 6 x 109, m3/a natural gas are imported, predominantly from the Soviet Union. The lignite deposits of the GDR are of Tertiary origin and are recovered exclusively by opencast mining. There are two large regions (fig. 2): - in the region east of the river Elbe (Cottbus/Senftenberg- "Niederlausitz") and - in the region west of the river Elbe (Halle/Leip- zig/Magdeburg). These deposits differ in geological age and conditions of depo- sition, consequently there are differences in their chemical and physical composition and, thus, in their uses. The younger Mio- cene coals of the main region in the East of the river Elbe belong to the epirogenetic type and have a low content of ash and sul- phur. Among other things, they are suitable for the production of brown coal high-temperature coke (Lauchhammer and Schwarze Pumpe). The older Oligocene coals of the Halle/Leip- zig region are bitumenous in certain areas. Therefore, they form the basis for production in low-temperature carbonizing and chemical plants. In the Halle-Magdeburg region, where the lig- nite is in contact with the underlying Zechstein subdivision, so- called "salt coals" are found.

Jan 1, 1989

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

With the advent of the resources boom in the late-1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large-scale Australasian open pit mining generally.

Jan 1, 2002

Gold mineralisation at the Kerimenge-Lemenge prospects is a classical example of myltiple, overprinting events, associated with intrusive-related hydrothermal systems. Repeated emplacement of high level dacitic porphyry bodies (Edie Porphyry; 2.4 - 3.8 Ma) was accompanied by a phreatomagmatic eruption which formed a diatreme-maar complex. Later hydrothermal fluids utilised permeable fault zones and diatreme contacts. Mineralisation took place during two main events. Stage I consists of early quartz - illite/sericite - carbonate phase with associated pyrite-arsenopyrite mineralisation. This phase is zoned from quartz - sericite-pyrite/arsenopyrite in the south at depth, to dominantly manganocarbonate - illitic clay - arsenopyrite- pyrite_s significant base metals in the north and at shallow levels. The majority of known gold (18.1 Mt @ 2.0 g/t Au) at Kerimenge is associated with Stage I activity. The gold occurs primary within the lattice of the sulphides and is metallurgically refractory. Fluid inclusion studies indicate early boiling and progressive cooling and dilution of hydrothermal fluids during the evolution of the Stage I event. Near paleosurface condensation of gases, which evolved off the boiling system at depth, produced abundant low pH bicarbonate fluids. During the waning phases of Stage I activity, these bicarbonate condensate fluids descended down permeable structures and formed banded manganocarbonate veins. High grade non-refractory gold mineralisation during Stage II event is restricted to favourable structures at relatively shallow levels and in the northern regions of the prospect area. Gold in this event exhibits a distinctive Au - Ag - Te -Cu geochemical signature, and is associated with hessite - tennantite - chalcopyrite mineralisation within quartz veining. Alteration and fluid inclusion studies indicate that this style of mineralisation is a result of the quenching of pulses of hot, late magmatic mineralised fluids by the cold condensate waters.

Jan 1, 1997

The middle-Devonian Dulladerry Volcanics is a complex of A-type, predominantly rhyolitic ignimbrites, lavas and breccias. They form a NNW trending belt some 90 km long and 10-20 km wide, east of Parkes, NSW. The volcanics are dominated by widespread ignimbrite units with minor basalts, sediments and rarer andesites. The volcanics were deposited in a sub-aerial, possibly continental rift setting and are similar in chemistry and age to the Eden - Comerong - Yalwal Volcanic Zone (EVZ) on the NSW south coast. The volcanics exhibit an unusual Atype chemistry (high Zr, Y, Nb, REE, Ga). This distinctive composition illustrates that the volcanics are not comagmatic with the adjacent Yeoval Granite Complex or Eugowra Granite, which show typical I-type fractionation trends. Epithermal gold veins occur in basalt and andesite in the Dulladerry Volcanics at Mt Aubrey (Hopf, 1992), near Baldry. Alteration also occurs in the Glen Isla and Red Hill areas, with epithermal sinter recognised at Glen Isla. Copper and minor gold mineralisation occurs at the contact of rhyolite and andesite at Reedy Creek, but is not of epithermal origin. The analogous EVZ also contains several epithermal gold fields and it is this style of mineralisation which provides the most prospective targets in the Dulladerry Volcanics. Although the Dulladerry Volcanics also contain high background levels of REE and metals such as Zn and Pb, the general lack of fractionation and water-undersaturated character of A-type magmas does not lend itself to the development of significant concentrations of these elements into a fluid phase and mineralisation. The prospectivity of A-type volcanics in general could not be regarded as high. However, an indicator of some fractionation in the Dulladerry Volcanics is provided by the fairly low abundance (average 230 ppm) and wide range (

Jan 1, 1995

SPOT imagery acquired in May 1986 of the areas that include the Dugald River lead-zinc lode, northwest Queensland, Australia and the Ngwenalekau copper deposit, Botswana has been evaluated and compared with LANDSAT MSS imagery of the same areas. The data have been processed using band combinations, band ratioing, principal components analysis and classificatory techniques and the outputs compared with those of geobotanical, geochemical and biogeochemical data as well as geological information. For both study areas the image processing techniques cited have successfully distinguished discrete vegetation associations related to discrete surficial and bedrock geological units; and, notwithstanding the sharp contrasts between the nature of the geobotanical anomalies that in both areas occur over mineralised bedrock in Proterozoic sedimentary sequences, they have successfully identified the areas of anomalous vegetation over the mineral deposits. Greater vegetational and geological detail is revealed than on outputs generated from LANDSAT MSS data [see Cole, 1977, 1982(a) and (b)]. The additional information yielded by SPOT imagery compared with LANDSAT MSS imagery results from its greater spatial resolution - 20 metres as against 79 metres - and from ti fact that the three SPOT MSS spectral bands - 0.50 0.59um, 0.615-0.68um and 0.79-0.89um - respectivelc cover those sections of the electro-magnetic spectrum in which leaf pigments, notably chlorophyll, absorption for photosynthesis and leaf cell structure strongly influence reflectance. This accords opportunities for the detection of reflectance aberrations caused by stress due to drought and/or metal toxicity as well as for the identification of anomalous vegetation communities of moderate sizr These cannot be accurately discriminated on LANDSA I MSS imagery on which only very large geobotanical anomalies like that over the Lady Annie phosphate deposit in northwest Queensland [Cole, 1977, 1984; Cole and Owen-Jones, 19771 can be detected.

Jan 1, 1988

THE exceptional rainfall characteristic of the West Coast of Tasmania, in conjunction with the rugged topography of the district, has always suggested the utilization of water-power, and from the earliest days of the Mount Lyell Company theeventual installation of a hydro-electric power scheme, making use of some near-lying lake, has constantly been kept in view. At the period of the inception of the company, however, the time was not ripe for such an undertaking, and it is only oflate that the various important considerations involved have sanctioned incun;ing the heavy expenditure necessary, with the positive assurance of permanently reaping the benefits expected. The West Coast of Tasmania contains many lakes of varioussites; situated at high levels, and, although the catchments of these lakes are not very extensive, still, the excessive rainfall is so constant over long periods that its regularity may be relied on as offsetting the limited catchments. The explanation of the abnormal rainfall is simply the circumstance that the West Coast Range forms the first high land barrier which is met by the moisture-laden westerly and north-westerly winds blowing off the Southern Ocean. By the time the clouds strike the mountains they ride very low, consequently the elevation of the range, the peaks of which do not exceed 3000 to 4000 ft. above the sea, is sufficient to cause a copious precipitation. Lake Margaret, which is situated five miles north of the reduction works, was first recognized as a possible source of waterpower by Mr. Hugh Ohrisp, a surveyor, who visited it about 1893-4. Earlyl in 1895, while the preliminary work on the erection of the first furnaces of the Mount Lyell Co.'s reduction...

Jan 1, 1915

By T Sirinawin, R H. Murfitt, W Shywolup

The Bong Mieu Project lies within the Pre-Palaeozoic Kontum Craton near the southern margin of the regional Phuoc Son û Tam Ky Suture. The Suture and accompanying Truongson Fold Belt of Indosinian age host significant gold and base-metal bearing districts including OlympusÆ other project at Phuoc Son to the west of Bong Mieu and OxianaÆs Sepon project in Laos. The Bong Mieu Project is located some 90 km south of Da Nang and some 30 km south-west of Tam Ky, the provincial capital of Quang Nam province in central Vietnam. The project area is covered by an Investment Licence of some 30 km2 which was granted in 1991 and a mining permit of some 365 ha granted in 1992. Several mesothermal, gold-silver deposits with assigned resources are present on the property. Deposits with assigned resources contain some 615 000 ounces of gold in situ. These are at Ho Gan and Ho Ray which are potentially exploitable by open-pit mining and Nui Kem which is potentially exploitable by underground mining. Newly discovered extensions to the known deposits at Ho Gan, Ho Ray and Nui Kem, and several other new prospects, are currently being investigated by drilling. The Ho Gan mineralisation is of mesothermal, shear and shear breccia quartz vein, as well as intrusive breccia hosted style. Nui Kem mineralisation is of mesothermal, shear and shear breccia quartz vein style. The Ho Ray mineralisation is of skarn (gold-bismuth-tungsten) and lesser quartz vein style. The deposits straddle and flank the east-west trending Bong Mieu Anticline which trends through the central portion of the Investment Licence. In this paper the geology of the deposits, details of resources, results of recent exploration on the Investment Licence and recent engineering and mining studies at Ho Gan are briefly reviewed.

Jan 1, 2004

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

The undeniable fact of life in the next 25 years will be the increasing difficulty of the physical conditions of Australian orebodies facing future miners. We are all familiar with names such as the 3000 orebody at Mt Isa, Hilton, Century, Macarthur River, Cannington, and Ernest Henry. These projects represent a significant. proportion of the planned underground mine development in Australia. Moreover, many of these new orebodies are an order of magnitude more difficult to mine and process than their predecessors. Extraction will be from deeper and potentially more hazardous working environments. Occupational health and safety considerations will place unprecedented demands upon mine operators and technology providers of the future.

Jan 1, 1994

By B Huls, B E. Smith, I Brake, M Yu

A brief outline of some of the pioneering events in the development of flotation technology, which originated in Broken Hill at the start of the 1900s, is presented. The development of the original Potter-Delprat process, the introduction of oils to generate froth flotation and the achievement of selective flotation processing are described, all focussed on solving challenges with the Broken Hill Pb-Ag-Zn ores. Some recent initiatives in flotation at BHP Billiton operations are also outlined, covering coal, copper, lead-silver-zinc and diamonds. Some views are offered on the characteristics of innovation in flotation and on possible trends into the future.

Jan 1, 2005

The hydrological cycle in nature, with particular reference to Australia . 2. The definition of water pollution drawing on the experience of several major countries. 3. A description of the pollutants in water, and why they are pollutants. 4. The classification of waters as defined by major overseas countries. 5. The criteria and standards developed by major overseas countries for the classification of waters. 6. A brief- summary of the legislation adopted by overseas countries for the control of water pollution, and of the organisation and administration of controls. 7. A study of Australian legislation and administration of controls of water pollution. 8. General observations and conclusions.

Jan 1, 1971

The optimization of management structure systems for coal mines is undertaken with the use of economic and mathematical models of the monitoring, manufacturing, and functional subdivisions of the systems. The main para- meter to be minimized is economic loss result ing from organization faults and this is achieved, in part, by optimum distribution of both technological objects and engineering and technical personnel. Models used are of the "gated" type, parameters for which are derived from analysis of manufacturing processes and from automatic information systems. The use of these models ofmanagement structures is only part of the process of optimization of those structures for coal mining operations.

Jan 1, 1977

By P Vix

A thermodynamic model of the copper Peirce-Smith (P-S) converter has been developed to predict the behaviour of magnetite in the converter slag, the amounts of slag and matte, the compositions of slag and matte, the volume of the bath, the bath temperature and the SEMTECH OPC signals. The predictions of bath temperature, slag and matte compositions and magnetite content in the slag have been validated by the industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment and temperature on the magnetite formation in the slag have been predicted and discussed. Some industrial applications of this model have been presented.

Jan 1, 2005

This paper outlines a range of strategies for steady state optimisation of most types of concentrators. Optimisation is considered in terms of comminution performance, energy efficiency, concentrator strategy and overall mine/concentrator operating philosophies. Application becomes more complex as the range of optimisation is expanded. However, the potential gains also increase. A step by step framework for data collection and analysis is provided. This process is facilitated by powerful simulation and mass balancing programs which are now in common use. Once a sound, steady state rationale for optimisation has been developed, it may be used to provide a fine foundation for process control system development.

Jan 1, 1993

By Dawes C. A, Mitchell R. A

A process control strategy has been developed for the lead circuit of the lead- zinc concentrator at The Zinc Corporation, Limited (ZC), Broken Hill, Australia. The general aims of the control system were to produce a final concentrate with a zinc content below a certain limit and, at the same time, obtain the highest lead recovery possible. As presently arranged the system involves control of the cleaner feed mass flaw by cleaner diverter tray manipulation and control of xanthate addition based on per cent lead in feed. Generally this approach works well but for abnormal conditions such as very high or law pH the system requires further improvement.

Jan 1, 1983