Search Documents

By J Kleynhans, D Vermeulen, V Cogho

A number of rehabilitated open cast coalmines in SA are already decanting. The paper focuses on the situation at one of these mines where the following information exist: monthly decant rates and rainfall; sulfate concentrations of the decanting water; water level measurements inside the mine prior to decanting; ABA analyses; information about the rehabilitation (drainage slope, vegetation, soil used). A 2D-model was constructed for the mine and calibrated against six years of flow data. About 85 per cent of the decant outflow rate comes from direct recharge on top of the rehabilitated mine while the other 15 per cent is derived from lateral groundwater inflows. The estimated recharge value was 17 per cent of the rainfall. Measured sulfate values showed that the sulfate generation rate for the mine was in the order of 7 kg/ha/d. Conclusions from the study are:most of the water decanting from rehabilitated open cast coal mines is derived from recharge via rainfall; given a specific sulfate generation rate, then: the lower the recharge the less the decant rate but the higher the sulfate concentration of the decanting water and vice versa; future prediction of the decant rate must be stochastic according to expected percentile monthly rainfall values; and as a first assessment of the predicted sulfate concentration of decant water from rehabilitated open case mines, the 7 kg/ha/d sulfate generation rate can be used.

Jan 1, 2003

By P Krauss, S Harpalani

Methane emitted from underground coal mines, along with ventilation air and known as ventilation air methane (VAM), constitutes the largest component of coal mine methane (CMM) emissions. Atmospheric methane, on the other hand, is a potent greenhouse gas with a significant adverse impact on the atmosphere. This has led to the development of various technological alternatives for its use as an energy fuel. Techniques involving oxidation of VAM, usually consisting of very low concentrations of methane, have been validated in the past. Prominent among these technologies are the thermal and catalytic flow reversal reactors, ancillary fuel technologies, lean fuel gas turbines, and concentrators and gasifiers. However, the efficiency of any VAM utilisation technique depends on the amount and concentration of methane in the ventilation exhaust air. Therefore, quantification of VAM emission from a coal mine is the first step towards identifying the most suitable technology for its utilisation for energy production. This paper presents an evaluation of the efficacy of VAM as an energy source. It provides details of a case study aimed at developing a technique to accurately quantify VAM emission from a coal mine. It further discusses the various VAM utilisation techniques available, and presents an economic evaluation of the alternatives. Based on the findings of the study, the most feasible method for VAM utilisation is identified for the mine. The paper summarises the procedure for quantifying VAM emissions and selecting the most suitable utilisation technique.

Jan 1, 2005

By Perring CS, Barnes SJ

The nickel exploration boom of the late-1960s and early-1970s led to the discovery of numerous komatiite-hosted nickel sulphide deposits, associated with variably serpentinised bodies of olivine-rich cumulates. Subsequent research has shown the importance of volcanological processes to understanding the genesis of these deposits. Crucial developments have come through consideration of the fluid dynamics of magmas and magma-crystal mixtures, through observation of the dynamics and geometry of modern day basaltic lava flows, through application of theory and experimentation on the kinetics of crystal growth from magmas, and most importantly from extensive detailed field mapping of komatiitic sequences in the Yilgarn Block and elsewhere. From these studies has emerged a new integrated view of the volcanological setting of komatiite-hosted deposits, and a recognition that a complete continuum of deposit types exists. Nevertheless, komatiite associated magmatic nickel deposits generally fall into two overall types based on the nature of the sulphide ore. In the first type the bulk of the ore is either massive Fe-Ni-Cu sulphide or a variable mixture of massive sulphide and an ore characterised by olivine crystals in a continuous matrix of sulphide occupying between 30 and 75 per cent by volume of the rock (called Matrix Ore). Nickel grades of massive sulphide ore range from 2 - 20 wt% and those of the matrix ore generally fall in the range 1 - 5 wt% (average 2.5 wt%) Ni/Cu ratios of the sulphide fraction are generally >10.

Jan 1, 1996

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

By Semple DG, Leach TM

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as Zone C, is a measured 440,000t @ 17g/t Au and 46g/t Ag with an additional indicated resource of 120,000t @ 16g/t Au. A diatreme breccia localised at an intersection of structures, and a relationship of gold to base metal sulphides, are highly indicative of a porphyry association. Typical epi-thermal features such as crustiform banded quartz and quartz pseudomorphing. platy calcite are also present and locally contain lesser gold mineral-isation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100m strike. A fluid flow model suggests that mineralising fluids were sourced from the diatreme margins and migrated laterally along dilatant structures. Bonanza gold grades are derived through fluid quenching in the flexure between a hanging wall split which hosts much of the Tolukuma Hill resource and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting. Potential for more ore remains within the Gufinis and the 120 veins as well as in the outlying Prospects.

Jan 1, 1994

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

Selective continuous surface mining is a rapidly developing system of mining which will have a significant impact on many present and future open cut mines. In many aspects the technology is in its infancy, whilst in other facets concepts drawn from other sectors of engineering are well proven. Full development of the potential and benefits of this technology will only be achieved if the mining companies and manufacturing companies work together to produce machines which the end user really wants.

Jan 1, 1986

Through partnering with mining customers, DYNO has been able to develop some specific technologies that benefit blasting operations particularly in underground mining. Some of these areas are: 1. Cost allocation and product tracking systems; 2. Borehole video surveys of breakthrough blastholes; 3. Borehole video photography for logging VRM blastholes; 4. Toe-load uphole loading for sublevel cave mining operations; 5. 3D blast modelling for underground ring blasting. This paper outlines these developments in the context of a Canadian underground metalliferous mine.

Jan 1, 1995

By Willett, Jacka

Group 3 were asked to discuss the treatment of spontaneous combustion. Before discussing specific cases we agreed that certain preliminary information should be available. The following questions are typical of the information which might be requested: 1. Have workmen been withdrawn? 2. Have gas samples been taken? 3. Is the mine gassy? 4. What are the details of water supply? 5. Are mine plans available? 6. What equipment is available? We discussed treatment in four different circumstances as follows: 1.

Jan 1, 1973

By J A. Didovich

Near the completion of undergraduate studies, students in mining-related courses are increasingly being presented the opportunity to undertake postgraduate studies. The current boom in the mining industry, the shortage of young professionals entering the industry and the lucrative starting salaries and packages on offer makes this a difficult and perplexing decision. This paper will outline what a PhD entails, discuss the benefits that a PhD can provide and discuss the timing and mode of a PhD.

Jan 1, 2006

By Middlebrook PD

The problems of education and research in the extractive metallurgy area are being tackled by the University of Melbourne through activities centring on the Department of Chemical Engineering. The establishment of the G.K. Williams Laboratory and the enhance- ment of the teaching of material relevant to extractive metallurgy in the Chemical Engineering course aim-at providing graduates and experienced researchers for the industry and at providing a strong research group carrying out industrially significant research in the area of pyrometallurgy.

Jan 1, 1986

The chief use of manganese ore is in the production of ferromanganese alloys for steelmaking. Manganese ores generally occur in tropical areas, which influences the type of treatment required. Present methods of treatment are relatively unsophist- icated but demands by customers for tighter specifications will necessitate the installation of gravity concentrator at many mines At present only limited tonnages of minus j in. product can be sold hence future development will centre around methods of producing an agglomerate satisfactory to the smelter.

Jan 1, 1969

By Dalzell R. W

A Conveyor Belt Fire Test Program was initiated in 1985 by the Approval and Certification Center (A&CC), Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The purpose was to evaluate the effect of entry air velocities on the burning properties of mine conveyor belts and assess fire test data from large- and small-scale tests. Belts meeting the fire-resistant standards of MSHA and agencies of other countries were tested in small- and large- scale fire tests.

Jan 1, 1988

One of the often overlooked factors affecting the capital investment decision in new or existing plants is the value of stock holdings necessary to maintain the plant. This paper puts forward a simple decision matrix on whether a part should be stocked depending on 1. the criticality of the item of equipment in terms of the effect on cash flow of its failure, 2. the lead time of the part, and 3. the stock holding value if it were Stocked.

Jan 1, 1986

By Aspinall T. O

This paper discusses the identification and assessment of risk for mining developments particularly for open pit mining. A distinction between sensitivity studies and risk analysis is developed, demonstrating the importance of geological and mining engineering judgement -as applied by experienced practitioners to the analysis and assessment of risk in such projects. Technical and financial risk analysis are discussed under: ò mineral resources and ore reserves; ò mining and processing methods; ò project construction; ò financing; and ò costs and commodity pricing predictions.

Jan 1, 1994

The BHP Steel Group embarked on a Total Quality Control (TQC) programme in 1984 in response to enquiries from a major customer regarding procedures for quality in materials supply.The TQC initiative has been adopted by all seven Divisions of the Steel Group and covers a broad and comprehensive range of management and workforce improvement initiatives.The development of the TQC initiative in the Collieries Division of BHP Steel over the past eighteen months has resulted in important experiences and leanings.

Jan 1, 1991

By Enugroho E, Nashution Y, Susanto M

PT Allied Indo Coal is the owner of the Parambahan Open Cut Coal Mine in the Ombilin Basin in West Sumatera with an annual production of in excess of 0.5 million tonnes/year of saleable coal.The parent company Allied Queensland Coal was one of the first foreign companies granted a contract of work. by the Indonesian Government. PT Allied Indo Coal is therefore a contractor to the Indonesian Government and pays a 20 per cent royalty of all coal mined.

Jan 1, 1992

The sucessful use of sewage sludge in land rehabilitation has been established and there is an abundance of overseas information on sludge reuse. Unfortunately Australia is behind Europe and North America in establishing sludge reuse policies and regulations. In Victoria the EPA has no publicised regulations and no communicated policy for sludge reuse. In the absence of sound regulations the onus is firmly on the operators of sewage treatment works to ensure land application of sludge is safe for the environment.

Jan 1, 1992

The cost of constantly extending a decline tunnel that plays a part in the actual extractive process is a revenue cost. The characteristics of such a decline tunnel are that it is dug in a series of relatively small excavations. It follows the ore body and is dug as close to the ore body as practicable. In addition, the decline allows for the extraction of ore in the immediate vicinity, with the ore being extracted in a relatively short period of time.

Jan 1, 1990