Search Documents

The paper gives details of the performance of a 6-ft. by 6-ft. grate discharge ball mill which was converted into a rod mill of the overflow type and then into a grate discharge rod mill. Proposals for further alterations are outlined.INTRODUCTIONThe mill of King Island Scheelite (1947) Limited recovers scheelite by gravity methods.Crushed ore at the rate of 34 tons per hour is divided between two mills. (6 ft. by 6 ft. and 8 ft. by 6 ft. respectively), the mill discharges being pumped to a common distributor which feeds seven Hummer Screens. Each screen has three 4-ft. by 2-ft. Ton-cap sections and repulping compartments are provided. The screen oversize is returned to the mills whilst the screen undersize is finished grinding section product. A third (6 ft. by 6 ft.) mill regrinding the coarser table tailings also discharges into the common Hummer Screen Distributor.The screen undersize is pumped to a bowl classifier which separates at 200 mesh. The bowl classifier sands are treated on tables whilst the bowl classifier overflow, after thickening, is treated in the slime plant by flotation. The flotation concentrate is further concentrated on vanners and slime tables.A recovery of 80 per cent. is possible by tabling whereas only 50 per cent can be recovered in the slime section. The object of comminution is, therefore, to reduce all the new feed to less than a certain mesh (22 mesh Tyler) with the production of a minimum quantity of minus 200 mesh material. cheelite is, a very friable heavy mineral (Sp.Gr. 6'0) and is therefore susceptible to overgrinding. For the evaluation of grinding performance it is hence advisable...

Jan 1, 1955

By T Cutts

Since 1989 Kalgoorlie Consolidated Gold Mines has managed the Kalgoorlie gold operations of joint venture partners Normandy Mining Ltd and Homestake Gold of Australia Ltd. Current production from the Fimiston Open Pit is approximately 650 000 ounces per annum. The mine incorporates a multitude of narrow shear hosted, subvertical lodes, predominantly within Golden Mile Dolerite. Traditionally KCGM has used blasthole based grade control in the Fimiston pits. A single sample is taken from vertical production blastholes, drilled on ten metre benches. This process was improved with the addition of infill drilling along blasthole rows to provide additional samples across strike. However the limitations of adequately defining subvertical mineralised structures with vertical blastholes remain. In 1997 the first of two trial areas were drilled with close spaced, inclined Reverse Circulation (RC) drilling. These tests indicated that RC based grade control had the potential to provide significant advantages. These include:improved delineation of mineralised structures, particularly across strike; reliable short-term mine schedules based on the advance data available from drilling over three benches; and the angled RC drilling is capable of providing samples of near stope and stope fill material which often remains unsampled by blasthole drills due to the safety constraints around unstable underground openings. Based on the success of this initial work RC based grade control was gradually implemented across production areas commencing September 1998. Some of the many challenges faced include:development of effective procedures and systems for the planning, logging, interpretation and modelling of the RC data; obtaining adequate drill coverage due to mine scheduling constraints and restricted access around underground openings; requirement for integrated systems to handle either blast hole or RC data; and development of effective methods to evaluate the performance of RC grade control. RC based grade control is delivering significantly improved lode definition, grade estimation and subsequent ore classification.

Jan 1, 2000

By J Webb

Anoxic limestone drains (ALDs) have been widely used in the passive treatment of acid mine drainage (AMD), but their effectiveness has often been less than anticipated. Iron hydroxide often precipitates around limestone particles and inhibits neutralisation. To determine the conditions under which iron hydroxide precipitates, a small-scale laboratory ALD system was built to enable a detailed examination of the chemistry of iron within the drain. For one experiment, a mixture of limestone and quartz was introduced to the drain to assist in the determination of the key mechanism governing iron precipitation. Synthetic anaerobic acid mine drainage containing Fe2+ (~130 ppm), SO4 2- and H+ was pumped at a rate of 30 mL/min up a 90 cm tall, 15 cm diameter vertical column filled with limestone gravel of 98 per cent purity. Three sampling ports were fitted at equal intervals along the column; water was periodically extracted for analysis at the sampling ports over an 11-hour period. Experiments were run at influent pH levels of 2 and 4. Results show that acid neutralisation to pH greater than 6 occurred at the inflow end of the drain. The greatest amount of iron precipitation (19.5 per cent) also occurred in this area. The lack of iron precipitation on the quartz surfaces in the quartz/limestone mixture indicates that neutralisation is the key mechanism for the precipitation of iron hydroxide on limestone particles. A pe-pH stability diagram derived for the laboratory ALD system indicates that ALDs will not be effective for AMD with pH 2. Influent waters with pH 2 require a pe of -2 (Eh: -118.4 mV) to avoid Fe precipitation upon neutralisation. Influent waters of pH 4 require a pe between -2 and -4.

Jan 1, 2003

By Szpindler G

The results of pot-furnace tests with 35 bituminous coals from 20 seams in New South Wales and Queensland were used to establish the relationship between coal properties, as determined by standard laboratory tests, and the combustion process. The rate of combustion is influenced chiefly by the expansion of the fuel bed, but this cannot be accurately predicted from the crucible swelling number of the coal.The effects of various other factors, such as calorific value and ash yield, were investigated and statistical analysis of the results shows that the coals could be classified satisfactorily according to two experimentally derived parameters, namely heat-release rate at an air flow rate of 260 lb/sq.ft/hr and air flow rate giving stoichiometric combustion. The grouping obtained is shown to be related to ash yield and swelling number.INTRODUCTIQNThe rate of heat release from the fuel bed of a travelling grate stoker and the efficiency with which the heat is used depend upon the design and method of operation of the furnace as well as upon the properties of the fuel. It is difficult to draw general conclusions concerning the influence of fuel properties from tests on a single stoker installation. In the pot-furnace test, on the other hand, a part of the same combustion process as occurs on a travelling grate is carried out in isolation, uninfluenced by furnace design variables, and consequently the effects of coal properties and of the method of pretreatment can readily be demonstrated.While the combustion pot provides a rapid method of assessing the combustion characteristics of a fuel during the ignition and burn-out stages under standard conditions, and of predicting changes in performance with changes in fuel or in air flow rate, it is unable to simulate certain features of furnace design and operation. Data from combustion pot...

Jan 1, 1962

Dilution in underground coal operations can be underestimated by up to five times during feasibility studies, with disastrous economic consequences. Every one per cent of stone waste introduced can reduce an in situ specific energy of 25 MJ/kg by some 0.25 MJ/kg and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some $A 1 million per year. This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation and presents the dilution trends from a continuous miner/longwall mine over an eight year period. The overall dilution level for the mine can be back-calculated by comparing the run-of-mine coal quality to the predicted in situ, undiluted quality. However, this will not identify the actual contaminant types, areas of the mine responsible for the dilution and the reasons for the dilution. This additional information is essential for controlling dilution to acceptable levels. Quality and horizon control using existing sampling information is generally only adequate for longer-term control purposes, and is not suitable for monitoring mining-induced dilution. The cost of close-spaced surface drilling to collect the information necessary for short-term control is prohibitive, particularly for deeper mines. However, much of this data can be collected through underground channel sampling and horizon control measurements taken during continuous miner development and longwall extraction. The mine runs the risk of not meeting contractual quality specifications and of increased equipment wear if this additional information is not available and the sources of dilution cannot be controlled. The information can also be used to plan longwall extraction heights on a short-term scale with resulting improvements in productivity.

Jan 1, 2003

By Dickson B. L

Groundwater geochemistry is controlled by chemical interactions with aquifer rocks, and offers a powerful geochemical exploration technique for locating concealed mineral- isation. Techniques are applied for identifying constituents of aquifers using the compositions of their groundwaters, collected from the surface through drill holes, water bores or springs. Even slowly moving groundwaters have passed through large volumes of rocks which surround any sample site. Products from these rock-water contacts modify the groundwater. By relating water composition to the minerals from which the dissolved species may have been derived, geochemical exploration information is obtained for a significantly larger zone than is represented by drill hole rock samples. In this paper we describe some solution chemical tech- niques we are applying in mineral exploration, particularly in areas of Australia where ground- waters are highly saline and contain enhanced concentrations of trace metals. EQUILIBRIUM MODELS FOR SALINE GROUNDWATERS Central to our technique is the assumption that in low rainfall regions, aquifer rocks and contained groundwaters are in chemical equili- brium. Solubility calculations then allow us to predict upper limits to the soluble products of groundwater interaction with aquifer rocks and to identify minerals with which the groundwater is saturated. Whilst equilibrium calculations require input of concentrations of all dissolved species, they are actually based on "activity" of dissolved species rather than the analysed concentrations. Unless waters have very low ionic strengths (a measure of total dissolved solids), activity of a solute is not equal to its analytical concentration but equals concentration multiplied by an "activity coefficent". Several methods exist for calculating mineral solubilities. The ion-association model, commonly used in programs such as WATEQ (Truesdell and Jones, 1974) and later deriv- atives such as MINTEQ, assume the formation of complex ions such as MgSO4(0), CaCl+, which are described by formation constants. Activity coefficients are obtained by the extended Debye

Jan 1, 1988

By R S. Suglo, G-K Er

Mineral processing is an essential component of a mine production chain and it accounts for significant proportion of the production cost. Over the past decade, significant research progress has been made in processing plant efficiency using theoretical, experimental and simulation modelling techniques. However, these studies are limited to process plant system as stand-alone units with no interactions with the mining units. In order to maximise the total mining system efficiency and more accurately simulate the system, the processing plant must be modelled as part of an integrated mining system. This becomes increasingly important in continuous surface mining systems, with limited ore processing capacity. In addition, plant efficiency is roughly estimated with known parameters or with simplistic statistical data, without regards to the stochastic processes governing these parameters, such as processing plant feed introduction. In this paper, a comprehensive model of the ore processing plant system is given and the object-oriented design (OOD) of the system is briefly introduced. The joint operation of ore processing plant system and haulage system is analysed. Numerical modelling is used to analyse the ore processing plant system under different conditions. Analysis of the results show that the optimum plant capacity is 0.7 tons/sec (2520 tons/hour). The results also show that the plant system resources cannot be fully utilised because the production rate is always less than the plant capacity. When plant capacity reaches an optimum value 0.7 tons/sec, the production rate is about 0.64 tons/sec. The underlying stochastic processes associated with plant and mine capacities cause this variability. In order to reduce this variability, there is the need to tightly set tolerances for the function variables.

Jan 1, 2003

By T Klinge, P Field, N Sugden, D Trenberth

Mining remains one of the key industries in Australia and many other countries with mineral wealth. In Australia, mining contributes 8.8 per cent to the countryÆs gross domestic product (McKay et al, 2000). In Queensland alone, mineral and petroleum industries contribute approximately $9.4 billion to the StatesÆ gross state product (2001/02) (Young, 2003). Increasing pressure on mining companies to perform in a global marketing environment requires mine management to consider more innovative ways to manage their resources û human, plant and equipment û which includes the gathering and analysis of operations data and information for improved decision making. For any mining operation utilising rubber tyred equipment such as trucks, front-end loaders and ancillary equipment, annual expenditure on tyres and related items can be significant. Even a small reduction in tyre operating costs can have a real effect on the business bottom line performance in the short term. Tyre Application Risk Management (TYREARMÖ) can provide substantial benefits in the long term across a number of KPIs not just through reduction in direct tyre expenditure but through flow-on improvements in safety, productivity and reduced environmental impacts. Several accidents involving tyres have also highlighted an increased need to consider the hazards and resultant risks arising from operations of rubber tyred mining fleets (Torlach and Johnston, 1990). This paper presents the process and results of achieving sustained safety and business improvement through the strategic alliance between an earthmover tyre management service provider, Klinge and Co (Klinge) and a BHP Billiton coal mine. The accompanying case study demonstrates in some detail the overall methodology, and the tools and technologies used where active management of data, its analysis and decisions taken have resulted in a 43 per cent improvement in tyre cost performance and a corresponding reduction in tyre-related downtime since the beginning of the alliance.

Jan 1, 2003

Mt Muro was a gold and silver mine in Central Kalimantan on the Island of Borneo, Indonesia. Aurora Gold through its Indonesian subsidiary Indo Muro Kencana owned the project. Processing commenced in November 1994, and ceased in June 2002. Mining, including prestripping, commenced in March 1994, and ceased in May 2002. Nominal throughput was 1.5 Mtpa, at average grades of 3.80 g/t Au and 99 g/t Ag. From the start of prestripping until the end of 1996, Drill Blast sampling was the main grade control method. After several studies into the viability of Reverse Circulation, including an assessment of costs and benefits, the switch from Drill Blast to Reverse Circulation was made in late-1996. From 1997 until the end of the project Reverse Circulation was the main grade control method. The mine-to-mill call factors û the reconciliation between predicted and actual tonnes and grades delivered to the mill û for the period from commencement of processing to December 1996 were 1.069 for tonnes, 0.949 for gold, and 0.969 for silver. The mine-to-mill call factors between January 1997 and June 2002 (excluding a period of significant illegal mining) are 1.086 for tonnes, 0.977 for gold and 1.025 for silver. At face value this indicates a 2.8 per cent absolute improvement for gold, and 5.6 per cent for silver. Using average grades for the project, an additional 5112 oz of gold, and 267 173 oz of silver were delivered annually to the mill using Reverse Circulation sampling instead of Drill Blast sampling. The additional recovered metal value is estimated at $US 2.87 M annually, significantly exceeding the cost of Reverse Circulation drilling. This paper discusses a number of issues that may affect the estimated benefits.

Jan 1, 2003

We can look at the water treatment and management strategies at some recently commissioned mines and minerals processing sites to see the likely future of water in mining. The future of water in mining will be based on a holistic approach to understanding the site water balance, appropriate treatment, reuse where possible, and environmentally managed discharge where required. This paper describes advanced and innovative water treatment and reuse processes as used by mines and mineral processing operations from around the world. Underground mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Mining and processing often accumulates wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and acidic and odorous sulfates. On-site reuse, environmental discharge requirements, as well as community needs for water, drive mine operators to consider the most appropriate water treatment process. Mining water treatment for the future is described using case studies of innovative processes. The case studies include treatment of mine dewatering water for beneficial application from Australian mines, Ballarat Goldfields and Bendigo mining, treatment of produced water from oil and gas projects, and treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Advanced and innovative processes including membrane filtration, reverse osmosis at extreme conditions, advanced biological treatment and water management are all part of these case studies. This paper uses real case studies of advanced and innovative mine water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is on innovative processes that may be more widely used in future mining û where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the mine or the local community.

Jan 1, 2008

By R Lovel, P Fung, J Manuel, M OÆCo

The iron blast furnace is the most widely used and efficient producer of liquid iron. The integrated steel works is however under environmental pressure largely due to emissions from sintering and coking. The combustion of coke breeze during sintering contributes to greenhouse gases (eg carbon dioxide) and is the source of much of the emissions of SOx and NOx. Coke breeze, the fines produced during coking of coal, is also suffering supply issues as coke demand increases while coking capacity is constrained by environmental concerns.CSIRO Minerals has been investigating the use of wood biomass/char as a substitute for coke during sintering. Wood biomass, or char produced from it, is an attractive carbon source as carbon dioxide can be sequestered into growing biomass prior to combustion. It has great potential to reduce the emissions from integrated steelworks and improve their environmental acceptability. Harvested biomass/char is also a renewable and sustainable resource. Samples of pine wood flour, sawdust and red gum wood char were characterised and used in small-scale granulation and sintering tests. Red gum char granulated as well as coke and could be used to make acceptable sinter. Large-scale sinter pot test were conducted with char to produce sufficient sinter for ISO quality tests and calculate sintering performance parameters. Results showed that coke could be completely substituted by red gum char during sintering without loss of quality and with actual improvements in sintering performance. Furthermore, gas analyses made during sintering showed that there were significant reductions in SOx and NOx when char was substituted for coke. It is anticipated that the results reported here, although preliminary, will stimulate an increased effort into further research on the use of char in iron ore sintering.

Jan 1, 2004

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By Muller M, Ashley PM

Massive sulphide ZnPbCuAg deposits in the Halls Peak district of northeastern NSW are of the submarine volcanogenic type. They occur as a number of small lenses enclosed in shale and epiclastic rocks, in association with felsic volcanics of early Permian age. The deposits crop out in steep terrain near the eastern edge of the New England plateau. Local relief of 700 m and slopes up to 50¦, coupled with an average annual rainfall of about 1000 mm has led to local severe landsliding in previously mined areas. Mining from the 1890's to the 1960's has also resulted in unconstrained drainage of heavy metal-bearing acid waters and physical dispersion of finer grained metalliferous sediments into the Chandler River. Waters emanating from the main landslide area, from underground workings and draining scattered unconfined stockpiles of massive sulphide ore have pH values of 3 to 4 and contain elevated contents of Zn, Cu, Pb, Cd and Fe. Chemical mobility of heavy metals into streams occurs under low pH conditions with Zn exhibiting the greatest dispersion. Increasing pH conditions downstream cause precipitation of Fe phases and coprecipitation of heavy metals. Physical dispersion of secondary metal-bearing minerals into the surrounding creeks results in wt% levels of Cu, Pb and Zn in the stream sediments thereby exceeding the regional background values by one to three orders of magnitude. Areas disturbed by mining are characterised by lack of vegetation, biomagnification of heavy metals into algae and lower plants, and partial recolonisation by metal-tolerant grass species (Snow Grass, Poa sieberana; Blady Grass, Lomandra longifolia). Rehabilitation measures will have to include landslide stabilisation, impervious sealing or removal of sulphidic materials, import of topsoil and revegetation by metal-tolerant, slow-growing native grass and shrub species.

Jan 1, 1995

This paper summarises the results of a study carried out for the Sustainable Minerals Institute, University of Queensland, aimed at identifying the major water-related issues facing the minerals industry internationally and the research required to support the development of practicable solutions. An overview is given of the sources and uses of the worldÆs water resources and of the regional and global sustainability of water supply and management. Agriculture is the worldÆs major user of water; it wastes more water than the minerals industry uses. Water reform and its potential impact on the minerals industry are discussed with particular reference to Australia and South Africa. The sources, uses and management of water on mine and processing sites are outlined. Particular attention is paid to the importance of groundwater as a source of often saline water that can be used in mineral processing and for other purposes. Aquifer storage and recovery has the potential to help conserve water resources. Generally, the major uses of water on mining and processing sites are for mineral processing and refining and for the associated tailings disposal. Water consumption for these purposes may be reduced by recycling process water, using saline water, paying close attention to water management, thickening tailings and using techniques such as dry stacking and paste. A change in the minerals processing paradigm in respect of water use could come through research into new, improved and less costly dry processing techniques. The treatment of mine and processing water will be required increasingly before water is reused, stored, discharged or sold, and before sites are decommissioned. Research and development are required to reduce costs and develop new treatment methods. Mine closure and decommissioning raise a number of long-term water issues requiring continuing generic and site-specific research and development.

Jan 1, 2003

By M P. Sandy, J B. Simpson

The empirical stope design techniques developed by Mathews et al (1981) and refined by Potvin (1988) and others, have gained rapid acceptance in Australia in the 1990s as a simple, æfirst-passÆ means of designing primary stopes. However, it is recognised that these æstability graphÆ methods can only provide broad design guidelines. Recently published stability graphs (Hutchinson and Diederichs, 1996) encompass a wide range of geological environments, which are not discussed, and the influence of time and blasting practices cannot be easily reviewed. The æscatterÆ in the graphs must reflect, to some degree, different operating practices as well as subtle but important differences in the pre-mining conditions that are not adequately accounted for in the æmodified stability numberÆ. Development of a ælocalÆ, site-specific stability graph may overcome some of these problems. At NormandyÆs Golden Grove Operations, Western Australia, detailed reviews of stope stability performance, including Cavity Monitoring System (CMS) surveys, are undertaken for every stope, with the objective of developing a series of local stability graphs, customised to site conditions and calibrated in terms of æAverage Falloff ThicknessÆ (AFT). Cablebolting of stope hangingwalls is used to develop reinforced æbeamsÆ on each sublevel, effectively dividing the full span into smaller, more stable æsubspansÆ. By analysing stope stability performance in terms of fall-off, cost-benefit studies can be undertaken of the effect of cablebolting and other options for modifying stope spans. The approach used to develop the local stability graphs, and their integration into routine stope design procedures at Golden Grove, is described. The experience gained during stope extraction in the Scuddles orebodies has been successfully applied to the Gossan Hill æC-PanelÆ orebody. This methodology should be applicable to other underground mining operations.

Jan 1, 2000

Pasminco is actively addressing the optimal utilisation of the known orebody at the Broken Hill mine, in addition to actively exploring for economic mineralisation in the region. As part of the policy of better utilising the known mineralisation a major upgrade of geological systems at the mine was initiated. The software chosen for this change was Maptek's Vulcan, mainly because of the ease of use of this package. Rather than having numerous data sources in varying software packages the mine aimed to limit interfaces and packages. The decision to upgrade the mine's software was not taken lightly, especially in view of the inature stage of Broken Hill mining operations. However, the current mine life of Pasminco Broken Hill mine is I I years, which is longer than many new mines setting up in Australia today. Also, a more sophisticated system brings with it a better understanding of the economic mineralisation, possibly extending the mine life further. The process of moving the Broken Hill databases into Vulcan was a huge task which included, database transfer, digitising, wire framing, modelling and eventually ore resource calculation. To ensure the validity of the new ore resource accounting system, the existing system was run as a duplicate for the introductory year, providing a comparison and if necessary a safety net. The benefits of such a change, however, became apparent almost immediately. Area geologists realised the opportunity to revise geological interpretations in their areas of responsibility, enabling them to obtain a better understanding of orebody morphology. Three- diniensional analysis provides an excellent method by which review of ore targets both in the underground and mine lease exploration areas can he made. As each new find of mineralisation enters the system and hopefully extends the mine life, the opportunities for further mineral exploration in Broken Hill area by Pasminco are enhanced.

Jan 1, 1997

Geostatistical conditional simulation is a method to assess variability and risk in mineral deposits and the tool has wide potential applications in the iron ore industry. Correct reproduction of multivariate relationships is important in iron ore simulation, especially between Fe and impurities such as Al2O3, SiO2 and P. The turning bands simulation method, using a full model of coregionalisation for multiple attributes, is the main multivariate conditional simulation algorithm used in the Western Australian iron ore industry. This paper discusses the results of a more recent approach using minimum/maximum autocorrelation factors (MAF) to transform and decorrelate the multivariate data prior to independent sequential Gaussian simulation (SGS). MAF-SGS results are compared to those of the turning bands approach in the Yandicoogina channel iron ore deposit (CID), and both methods performed well in simulating Fe, SiO2, Al2O3 and P distributions. Extensive checking of simulations showed that both approaches could reproduce multivariate statistics and spatial continuity of the original conditioning data. Both approaches reproduced the histograms and variography of input sample composites. While the MAF-SGS approach requires additional transformations when compared with the single normal scores transformation required for the turning bands method, MAF requires only that the direct semivariograms be modelled. In contrast, using turning bands with multiple attributes requires modelling a full linear model of coregionalisation, which can be difficult to model because of the need to ensure the model is positive semi-definite. Turning bands may be preferred if there are a modest number of correlated variables allowing construction of a linear model of coregionalisation that adequately models the multivariate behaviour. MAF-SGS is preferable for larger numbers of correlated variables. Both MAF-SGS and turning bands methods performed well in conditional simulation of correlated variables at Yandicoogina.

Jan 1, 2007

The Wild Dog gold-silver-copper deposit represents a new ore-deposit type in Papua New Guinea. The telluride vein mineralisation is associated with a Tertiary caldera and has similarities with that from the Baguio district, Philippines, Vatakoula, Fiji, and the San Juan Mountains, southwestern Colorado. The deposit, discovered in July 1983, has negligible stream silt and concentrate anomaly, and a float-train limited to within 300m of the prospect. The comparatively recent exposure of the vein system may explain the limited stream expression of the deposit. At least three major veins occur in the deposit; the vein system strikes north- northeasterly, dips 78¦W, and has a maximum strike length of 1350m. Veins are enveloped by a wallrock dominated by an assemblage of quartz-illite-pyrite. Four types of silicification related to multiple vein filling events have been defined on the basis of field relationships, drill-core intersections, petrology and fluid inclusion study. To December 1986 a total of 22 diamond drill holes (2304m) and 40 reverse circulation drill holes (1833m) have been completed on the deposit, defining a 750m zone of interest. The upper 30m of the deposit is oxidised. Much of the high-grade mineralisation in both the sulphide and oxide portions of the deposit is restricted to ore- shoots which strike parallel to the overall vein structure and are vertical to steeply westward dipping. They are defined geochemically by the lg/t Au cutoff and geologically by the relative increase in the vein density of auriferous grey-black sulphidic silica, the final vein filling event. Metallurgical studies and the results of close-spaced drilling have demonstrated the very good repeatibility on duplicate assays, and the extremes of grade variability of mineralisation over very short distances. The good assay agreement on duplicate samples .s indicative of fine, dispersed gold.

Jan 1, 1987

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986

By S M. C Verryn

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis of metallurgical products. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine process control. Knowledge of the crystal structures of the major phases is essential for Rietveld analysis, and these are well known for most minerals and major phases in metallurgical products. It provides the basic structural information necessary for the determination of mineral stoichiometry and for elucidating solid solution behaviour. Modern methods, such as simulated annealing and charge flipping, permits the determination of crystal structures from powder data. Unit cell data can be used where conventional microchemical analysis is unable to provide an answer to the extent of solid solution in ilmenite roasting. Unit cell data (by XRD) is used to determine the amount of roasting necessary for the development of magnetisation to be able to separate chromite from an ilmenite concentrate. Phase quantification is probably the most widely used application of XRD analysis. It is used for materials balance in the minerals and cement industries, and it is finding novel applications in the iron and steel industry. Applications of XRD in high-temperature metallurgical processes are increasing. In this paper the phase chemistry of iron ore sinters, the evaluation of subsolidus reactions in titania slags and the identification of furnace accretions are discussed. Despite the success of the Rietveld method in phase quantification, the method still needs further development in the quantification of closely related or polytypic phases. The quantification of pyrrhotite phases using various Rietveld programs still gives ambiguous results. This is also true for the different SFCA phases in iron ore sinters. Clearly the analysis of similar phases, differing only in the presence of weak superlattice reflections is still problematic.

Jan 1, 2008