Search Documents

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982

By Warren R

Croesus Shaft is one of two operating shafts on North Kalgurli Mines Limited's Fimiston lease.At the cessation of gold mining in 1974, the workings at Croesus were allowed to flood. Large quantities of deslimed mill tailings used in filled stopes were washed into the shaft and surrounding drives, making re-access very difficult. The shaft has been desludged from the 9 level to the 15 level, and a loading pocket installed below the 14 level. A vacuum lift unit was installed underground to facilitate the removal of the slime and spillage.Stoping at Croesus was hampered by poor drainage, pumping, and shaft availability. These difficulties have been overcome by utilising an open stoping system for the relatively steep, narrow, high grade stopes. Open stoping has proved to be effective and economic.

Jan 1, 1985

By Smith JW

Studies of 13C/12C ratios of carbon dioxide in seam gases and in secondary calcites show that 1. In mines prone to carbon dioxide outbursting, the source of this gas is external to the coal. 2. Faults draining reservoirs of magmatic or primary carbon dioxide, rather than intrusives, are the most likely points of entry of carbon dioxide into mines. 3. The higher the concentration of carbon dioxide in seam gas and the wetter the mine, the lower the likelihood of secondary calcite occurring as a filling in cleats, fractures etc. 4. A -role played by carbon dioxide in promoting outbursting may be the conversion of calcite to soluble bicarbonate, the removal of this in mine water and the subsequent weakening of the resistance of the bulk coal to stress.

Jan 1, 1980

By R McConnochie, J V. Rowland, J L. Mauk

The Sovereign prospect in the lower Waitekauri Valley of the southern Hauraki Goldfield occurs in daciterhyolite flows and volcanic breccias of the Waipupu Formation. The lower Waitekauri Valley contains a series of NE to NNE-trending normal faults, and the Sovereign prospect lies in a NW-striking graben. The structure of the Sovereign prospect is complex. NE to NNE-trending veins and normal faults dominate the area, however WWNW and N to S-trending structures occur locally. Kinematic analysis of these structures indicates predominantly dip-slip movement, with a local strike-slip component. At least two sets of veins occur in the area: 1.        steeply dipping veins; and 2.       low angle veins, which cross-cut and locally offset the steeper dipping        vein set. Mineralization appears to have formed during normal faulting in an extensional regime.

Jan 1, 2007

By R Loweth

The application of discreet event simulation has matured in modelling manufacturing systems for production analysis. This simulation tool was used in studying a number of mining operations, especially material handling processes. The study of truck-shovel operation including equipment matching, selection, and production estimation utilised the discrete event simulation for providing valuable decision-making information. The sophistication of the available simulation tools grew over times, and simulation driven animation was used to facilitate the validation and visualisation of the simulated system. This form of visualisation enhanced the simulation use greatly. First of all, it provided a communication medium to transfer information to the non-technical managerial personnel as a better decision-making tool. Moreover, the animated visualisation provided a validation tool to check the working of the simulated system and interaction among its components.

Jan 1, 2003

We are all no doubt aware that with today's high costs it is more important than ever to get the maximum possible return on capital invested in the mining industry. Screening is an important and often costly process in the size classification of industrial minerals and for this reason alone it is essential for both managers and operators to fully understand what type of screening equipment is best suited for a particular application and why. The advent of elastic materials such as rubber and polyurethane have added a new dimension to the process of screening. It is important to understand why the physical properties of these materials can be of benefit in the screening process, and recognise which type of screening applications best take advantage of these orooerties.

Jan 1, 1984

By Moon N. T, Torrance A. C

This study has considered the effect of mechanical shock on the resilience of the glass microspheres commonly used to sensitize an explosive emulsion. The damage to the glass microspheres caused by detonating cord, emulsion manufacture and the manufacture of the glass microspheres were considered along with the effect of sensitizer concentration on explosive performance. Reductions of up to 50% in the glass microsphere concentration of an emulsion explosive can result from poor initiation practice, such as the use of high strength detonating cord as downlines during initiation. Laboratory results suggest that detonating cords of strength greater than 3.5 g/metre should not be used as this can seriously affect explosive performance, particularly in small diameter charges. This reduced performance results from damage to the sensitizer elements and recrystallization of part of the emulsion phase.

Jan 1, 1990

By McPherson M. J

This paper describes a major ventilation study for the expansion of the El Teniente mine operated by Codelco, Chile. El Teniente is one of the world's largest under- ground mines. The design effort was under- taken in three stages and involved a partial mine ventilation survey with network simula- tion, detailed stope ventilation investiga- tions, and design of the entire mine ventila- tion circuit based on production plans to achieve 112,000 tons per day by 1995. The partial ventilation survey provided values of representative friction factors and resistances for typical ventilation raises and airways. These values were used to conduct detailed modeling of the block caving levels to investigate the most cost effective and practical means of providing the required ventilation. The results of these analyses were extrapolated to the proposed expanded mechanized zones.

Jan 1, 1988

By Richmond AJ, Allan J

The use of long-hole in-seam drilling techniques for seam gas drainage ahead of mining was introduced to the Australian coal industry by ACIRL in mid-1981. ACIRL's research program has involved the development and demonstration of drilling and borehole survey technology in addition to evaluating the gas drainage potential of long-hole in- seam boreholes. This paper presents the results of the long-hole drilling carried out to date in the Illawarra District of the New South Wales coal fields. Drilling experience in relation to both vertical and horizontal directional control of the drill string, drill performance and borehole survey techniques are discussed. In addition, results of gas drainage effected by the long boreholes are presented. Future potential and requirements for further development of this technology are Reviewed.

Jan 1, 1982

By Smith IEM

Some samples from arc-type volcanic suites collected in northern New Zealand and southeastern Papua New Guinea show rare earth element (REE) and Y abundances which are enriched relative to the those typical of their respective associations. This enrichment appears to be the result of an alteration process which selectively mobilises the REE and re-precipitates them as REE-bearing minerals in veins and interstitial patches. The alteration is on a micron scale and is not detected in routine petrographic examination. The spectre of REE mobility in young apparently fresh rocks is important to igneous geochemists who use REE abundances to constrain petrogenetic models and may also be important because it indicates the operation of a natural REE enrichment process which could operate in the formation of economic REE deposits.

Jan 1, 1990

By Payne AR

The high cost of gateroad repairs and maintenance in U.K. longwall coalmining is a clear indication of the failure of permanent support systems to fulfill their prime function, i.e. control of strata movement. The main component of gateroad support is the pack, the design and materials of which have experienced an important development process during the last 10-15 years. More recently, research investigators have attempted to give a design basis to pack quality and dimension, and reference is made to two theoretical approaches. In the course of a current research programme based upon in situ monitoring, interim design recommendations have been proposed as a means of effecting improvement in support efficiency. Identification of characteristic deformation behaviour forms the basis of the recommendations made and the subsequent improvement in gateroad performance reported.

Jan 1, 1986

Gold occurs at Mt. Charlotte associated with a stockwork of pyritised quartz veins in Unit 8 of the Golden Mile Dolerite. The ore- body is massive, 200m long and 40m wide and has been proved to over 600m below surface. Mining is by sublevel ring drill stoping with the ore recovered by diesel powered equipment. Ore reserves are based on traverses of diamond drill holes oriented to produce an equal intersection width on the two principal sets of quartz veins. Assay and geological boundaries are marked on each drill section and this boundary is transferred to mine plans and cross sections. Ring-drilling patterns are based on the cross sections and the resulting mining outline is transferred back to the drilling sections. The mine ore reserve is calculated from the mining outline.

Jan 1, 1979

By Stone AM, Romensky G

The requirement for economic operation of unit trains carrying bulk materials has dictated that rapid and accurate bulk loading methods be provided. The train loading station at Phosphate Hill, built for Queensland Phosphate Ltd. to load rock phosphate, provides this facility and whilst the concept used is not unique, it contains a number of novel features that are considered to advance the "state of the art'' in this field. This paper briefly reviews some alternative concepts evaluated, and describes the design and operation of the scheme ultimately selected as being most appropriate to the project requirements. it is one which utilises a variable speed belt feeder whose speed is controlled in proportion to the weight rate of material moving on the belt as measured against a set point

Jan 1, 1978

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998

By T Kang, V Sahajwalla, L Lu

During devolatilisation, physical behaviour of coals was investigated in horizontal electrically heated furnace with an inert gas atmosphere, and gasification rates of four coal chars and coke were measured thermogravimetrically in a carbon dioxide atmosphere at temperatures in the range 1100oC - 1500oC. The volume change of chars was also measured in horizontal electrically heated furnace at various temperatures. Both reactivity and the activation energy for the gasification of coal chars were found to be strongly influenced by pore structure and the carbonisation conditions employed during preparation. CO2 reactivity of chars increases with increasing reaction temperature, and particularly increases more rapidly over 1300¦C. CO2 reactivity of coke is lower than that of non-coking coal chars in the range of 1100¦C to 1500¦C. CO2 reactivity of chars with smaller pore area and bigger pore diameter is less than that of chars with bigger pore area and smaller pore diameter. During gasification, the volume of chars did not change significantly at the lower temperatures of 1100¦C and 1200¦C, but at the high temperatures, 1300¦C to 1500¦C, the volume of chars quickly decreased due to ash softening and melting. The CO2 reactivities of the chars are controlled by the mixed control of chemical reaction and pore diffusion in the temperature range 1100¦C to 1300¦C, and by bulk diffusion in the temperature range 1400¦C to 1500¦C.

Jan 1, 2000

Metallurgical accounting can be defined as the monitoring of the valuable metals from the time the ore is broken at the primary crusher until the time that we have the saleable products and residues. The overall purpose of metallurgical accounting is to provide management with up-to-date inform- ation that can be used to control mining and metallurgical oper- ations. The decisions that are taken on the basis of the information that the metall- urgical accounting system provides should result in improved control and, ultimately, increased revenue. The current state of accounting is a result of an extended evolutionary process and will continue as process plants bec- ome more sophisticated. Differences in mine æcall factorsÆ and grade control reconciliation can lead to frustration between the siteÆs geoscie- ntists and its metallurgists leading to a level of distrust in the mill grade. Metallurgical accounting is not included in sufficient detail in undergraduate courses and the acceptable industry standards have developed based on what is considered acceptable to industry personnel and consultants. There is now the AMIRA P754 Metal Accounting, Code of Practice and Guidelines Handbook or reference manual. Computer based databases and spreadsheets have transformed tedious bookkeeping into an important management tool. Over time these standards have improved with developments in analytical procedures, weighing technology and sampling. This paper provides anecdotal examples of problems and improvements observed over a number of years within the gold industry in Australia and overseas.

Jan 1, 2009

THE writer of this paper well realizes that the majority of engineering and metallurgieal works have from time to time evolved mechanical devices which are of great value as regards application in an operating plant.Many of these deviees would not be apparent to an individual making a brief inspection of works such as these, and it is for this reason that the writer proposes to outline a few of the devices which have been evolved by the engineering department of the Broken Hill Associated Smelters Pty. Ltd.NOVEL METHOD OF MACHINING A SPHERICAL JOINTFig. 1 represents one half of a casing for a ball-joint coupling. In the ordinary methods of boring an external spherical casing, that is with a radius bar attached to the tool rest of a lathe, there is always an error in the bore. It has two flat sides, and this error is inherent in the ordinary orthodox method and cannot be corrected. The engineers of the Broken Hill Associated Smelters Pty. Ltd. undertook a job that had to be extremely accurate, and the tool shown in Fig. 2 was evolved. The tool is not exactly fool proof, but in the hands of an average mechanic an absolutely perfect FIG. 1. sphere can be bored. The casing has to be held in the lathe in such a manner that one half can be removed without affecting the setting of the work. The business end of the tool is then placed inside the...

Jan 1, 1922

The great philosopher, Marshall McLuhan, is said to have stated that the use of forecasting as a means of guiding future actions is akin to driving an automobile through observations made in the rear-view mirror! In effect, in forecasting it is assumed that there will be an orderly progression from the past into the future, and that the model will be sufficiently unvarying for use to gauge both the directions and the rates of change. The concepts of forecasting have served man well in disciplines in which the relationship between causes and effects can be clearly demonstrated; such as between rainfall and crop yield, for example. These are of no value, however, when conditions change rapidly and unpredictably, or when there is no model at all. Even worse, under such circumstances our preconceived notions may cause us to make some horrendous errors in judgement. Such are the risks at present in attempting to make an assessment of the educational needs of the minerals industry for the coming century! The model, and the conceptions that we have had of the linkages between cause and effect are in disarray. Minerals markets are chaotic, and there is almost no ability to forecast trends in metal values. Linkages between supply and demand seem tenuous. Internationally, producers are struggling for survival. Mine closures, temporary shutdowns, and reopenings are frequent occurrences. Decision-making under uncertainty is probably one of the most certain things about the world mining industry Today!

Jan 1, 1986

Obvious differences in mineral deposit types occurring in Outer Melanesia and Northern Chile can be related to the sub- marine-dominated nature of volcanism in the' former area and the subaerial-dominated nature in the latter area. Subtle variations in subvolcanic epithermal-porphyry ore systems between the two areas probably result from differing ore fluid compositions. Hydrother- mal convection cells in Outer Melanesia will be seawater-dominated, consequently rela- tively high salinities and chlorine contents will characterise the ore solutions. Trans- portation of metals as chloride complexes is likely and the ease of seawater sulphate reduction to sulphide in the ore systems will lead to widespread, sparse dissemination of sulphide minerals. Relatively low grade por- phyry copper deposits will typify these ore systems. In Northern Chile hydrothermal convection cells will usually be dominated by meteoric waters. Consequently ore fluid salinities are likely to be lower and chlorine will be less abundant. Under these circum- stances transport of ore metals as bisulphide complexes could be important. Boiling and loss of H2S gas from these fluids would lead to rapid precipitation of metals and higher grade deposits. Erosion rate is a very important factor in the preservation of ore deposits and this may be the major control on the richness of a metallogenic province. The abundance of mineral deposits in the El Salvador region of Northern Chile compared to Fiji is probably a function of the much lower rates of erosion in the former area.

Jan 1, 1987