Search Documents

By Monette J. C, Nulty J. H

High temperatures and pressures are required to obtain acceptable stripping rates. Higher chemically induced stripping rates could reduce the need for higher temperatures which lead to cyanide losses. The higher rates could lead to lower carbon inventories and higher gold production. This paper reports laboratory and continuous test unit data which strongly suggest that the preceding can be achieved. New stripping agents demonstrate efficient stripping under conditions of cyanide depletion such as after carbon acid washing. Stripping times for gold and silver can be reduced by at least half compared to caustic cyanide through the use of these novel substances.

Jan 1, 1991

By N Meyer

This paper presents a research project referring to the stability of submerged walls of open pit mines and the actual state of development. Obviously the slope stability analysis is always a rather complex problem, because it is difficult to reduce the problem to a design scheme and to define the available in situ soil strength. Especially the design of submerged slopes represents a problem. The state-of-the-art slope stability analysis is based on a simplified modelling of slope failure and soil behaviour and with this predicted stable slope inclinations of sand slopes below water-table are less then half the angle of internal friction. Slope angles calculated like that canÆt satisfy the mining companies. One of the problems that have to be solved is the reliable determination of the long-term stability of non-cohesive, submerged slopes, which is not only dependant on geotechnical and hydrogeological parameters of the subsoil, but is also significantly influenced by how the slopes are made. The research project points at the relations between mining and geotechnical engineering with the main aim to find a more suitable stability analysis which takes both soil behaviour and mining influences into account.

Jan 1, 2003

By Gillies A. D S

Replies to a comprehensive questionnaire on mine water resource management systems (WRMS), which were distributed to a selection of Australian mining operations in 1991, are analysed. Although the replies cannot be considered fully representative of the industry, they do provide a good qualitative indication of water resource management in the industry at that time.Within Australia's largely arid land mass, a majority of mines nonnally need to conserve water, a few need to dispose of water and a number face a seasonally varying position. An assessment of the importance of WRMS compared with management of ore extraction and processing is given. A risk assessment of failure is given; there is more acceptance of WRMS failure in the mine compared with the mill. An assessment is made of considerations in WRMS design. Managements are generally pro-active in the design of WRMS and in the setting of perfonnance standards. The operational characteristics of mine systems are examined in detail.Companies generally do not appear to allocate sufficient resources for the collection of basic WRMS monitoring data and knowledge of the water budget to efficiently manage the system. This indicates scope for considerable cost savings in most mines.

Jan 1, 1995

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

Today's emphasis on the enterprise bargaining process must be seen as an opportunity for organisations to further develop occupational health and safety standards at work. In particular, this shift from a centralised industrial relations system to employer, employee bargaining, presents organisations with an excellent opportunity to develop OH & S at the `shop floor' level. This is despite real difficulties in presenting hard data on the cost benefits. Unfortunately, examination of enterprise agreements ratified by the Australian Industrial Relations Commission (AIRC), show that less than 32 per cent contain provision for occupational health and safety. Those addressing the issues of occupational health and safety have included segments such as: ò rehabilitation activities; ò a new emphasis for workplace occupational health and safety committees; ò formalising procedures related to hazard identification and control; ò the use of personal protective clothing; and ò occupational hygiene and health monitoring issues. For example, an enterprise agreement reached between CIG-Gases and their unions, included clauses which commit employees to attending ten safety meetings and two work place inspections each year, in order for them to receive any further pay rises.

Jan 1, 1995

As an older member of The AusIMM, I received my 30 year æPearl AwardÆ in June and had my 50th birthday two weeks ago, I am honoured to be here today. I thank those responsible for their confidence in me and in my ability to hopefully hold captive a broad group of individuals who are here as equals, sharing an interest, no a passion in blasting technology and associated works à over the two days you will hear some excellent operational and technical presentations I am sure. But today I will digress; I want to talk about the importance of leadership and how it indeed can be the catalyst for success, improvement and change. There has been much written about leadership, its principals, the charismatic leaders, the doÆs and donÆts and so on à and I for one am not about to give you the Holy Grail; there are many experts with greater wisdom than I on this subject matter. What I do want to do is explore the application of this passion to examples within the world stage and some examples drawn from my experience in mining.

Jan 1, 2007

The last two years have seen a rapid change-over from mechanised cut and fill. stoping to the more economic and productive long hole open stoping method, such that today more than 80 per cent of total production is won from open stopes. At first drilling was by sub-level rings and/or parallel up and down holes from inter- mediate sill horizons using conventional exten- sion rod equipment. Sub-levels were developed no more than 40 metres apart to allow accurate drilling. Compact, crawler mounted in-the-hole hammer equipment was introduced as soon as it became available in Australia. Today, all open stope drilling is done with three Atlas Copco ROC306 rigs and two Ingersoll-Rand CMM jumbos. Fans of 115 mm diameter holes, varying from near vertical down holes to horizontal, are drilled with a burden of 3 m. Toe spacing varies from 3.5 m to 4 m. An Atlas Copco DG418 booster compressor is used to boost run-of-mine air from 700 kPa to 1400 kPa in the areas of longest drilling. This has improved overall drilling performance in these areas by 40 percent.

Jan 1, 1977

By N Ross, N Goldup

In recent years the heavy mineral mining industry has started to look more closely at the feasibility of mining moderate to high slimes deposits. During the initial stages of orebody evaluation the primary purpose of the pilot plant is to produce heavy mineral concentrate for metallurgical evaluation. Hence, generally little consideration is given to the disposal of the waste material (slimes and tailings). This paper suggests additional, simple, low-cost, tests that can easily be incorporated into an initial pilot plant operation. With this data a more definitive evaluation of available waste disposal options can be made during the early stages of the project. Thus, permitting better project focus and utilisation of resources. These tests include free settling of slimes, natural slimes drying and consolidation (undrained and drained), tailings stacking angles, and particle size distributions of input and waste streams, etc. The objective and method of each test is summarised, together with its relevance to possible waste disposal options. The results of this preliminary testwork can later be used to expand upon and define further tests for the second phase of pilot plant operations, which will enable a more definitive evaluation of a proposed waste disposal solution.

Jan 1, 2001

By Borsaru M

The production of high-grade calcined bauxite is very dependent on the moisture content of the final product. Existing procedures rely on the ignition of small samples to monitor the effectiveness of the calcination process. The results obtained by this gravimetric technique are several hours behind production and do not permit regular adjustment of the furnace to optimize the control of the chemically bound water content (LOI).To provide rapid and hence more relevant results, a neutron moderation technique has been developed for measuring the LOI of bulk samples of calcined bauxite while they are still hot. The method uses fast neutrons from an 241 Am-Be neutron source to irradiate the samples, and the backscattered thermal neutrons detected are a measure of bound moisture content.The rms deviation between neutron and conventional determinations of LOI, in 15 calcined bauxite samples, was 0.08 per cent LOI over the range 0.1 to 0.9 per cent LOI. When allowance is made for the rms error in the ignition method, the error in the neutron method is found to be 0.07 per cent LOI.

Jan 1, 1985

By D E. Freeman, M A. Somerville, B M

A program of re-planting native mallee trees, which can be harvested on a short rotation cycle, has been initiated in Western Australia to counteract increasing soil salinity in the wheat belt region. Large volume applications for the wood products generated by these plantings are required to improve the returns to farmers. The metallurgical industry is a large-scale user of carbon, and a project was carried out through the Centre for Sustainable Resource Processing to investigate the use of mallee-derived carbons in metallurgical processes. The use of renewable carbon sources, such as charcoal, to replace fossil carbon has the additional benefit of reducing the net CO2 generated by the metallurgical industry. Experiments were undertaken to assess the performance of mallee derived charcoals as reductants for the solid state reduction of ilmenite and for iron ore bath smelting. Rotary drum reduction tests showed that the reduction rate of ilmenite with the mallee charcoal was approximately twice that of Collie coal at the same fixed carbon/ilmenite ratio in the bed. Iron bath and slag bath injection tests demonstrated that the mallee charcoals dissolved readily in molten iron carbon baths and reacted efficiently with iron making slags.

Jan 1, 2006

The cement industry requires large quan- tities of limestone, its main raw material. It is the major consumer of this mineral. Limestone is widely distributed throughout Australia but location in relation to major markets, and transport considerations render most deposits of no economic value. Of those which are sufficiently close to the major me- tropolitan markets many are rejected as being unsuitable on grounds of quality, inadequate size for major development, or other reasons such as environmental considerations. Detailed geological investigations are necessary, not only to prove raw material sources prior to establishment of a cement works but also to permit planned extraction programmes and satisfactory grade control during subsequent development. Conventional field techniques have generally proved adequate for raw material exploration. Data assessment and reserves estimation also are by conventional methods although the specific requirements of the industry relating to raw material and cement quality, the type of manufacturing process and fuel used are relevant. A number of case studies from different geological environ- ments are examined and comparisons made bet- ween the predictions of the exploration stage and subsequent experience in quarrying prac- Tice.

Jan 1, 1979

SASOL Synthetic Fuels has recently completed the design of sampling systems for raw and blended coal feeding the gasifiers at Secunda, South Africa. The new systems will replace manual, stopped belt sampling and have been designed to achieve specific accuracy targets on a daily basis. The sampling system is unusual in the coal industry in that the fines content (-5.5 mm nominal) of the coal is very critical and is to be determined with high accuracy.The sampling system was designed to meet carefully considered target accuracies using methods of modern sampling theory. The heterogeneity of the coal streams involved with respect to the critical analytes was determined by appropriate sampling and sample analysis. The statistical characterisation of the time variation of analytes in the process streams was based on variograms derived from on-line ash gauges. From this point, the design was completed using fundamental statistical sampling theory and some simulation studies. The paper discusses the development of the sampling system design in detail as well as the plans to use the data stream to provide timely alarms when the coal quality deviates from the target specification.

Jan 1, 2002

By Wang Xia, Zhou Aiming, Shi Shengyi

Zhangmatun Iron Mine is situated in the suburbs of Jinan city, Shandong, China. Because of surface environmental constraints, no suitable site can be selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a doubleshaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two stopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining. Utilisation of cemented tailings backfill solves not only the problem of disposal of mill waste, but also the resource problem of providing backfill materials to the mine. The strategy also maximises ore recovery for the mine.

Jan 1, 1998

By S Slusarczyk, Z Kozlowski

Vibration of surface caused by seismic quakes can make a risk to great mining costruction. We have to do with this risk in the Belchatow open cut mine where seismic quakes of various energy and range have occured since the end of 1970s. The seismic risk influence on the mine structure with the special attention to the slopes of an internal dump has been presented. Hydrogeological and geotechnical conditions of the lignite mining and internal dumping of overburden and ash from Belchatow power plant have been considered. Seismic activity in Belchatow open cut from 1979 to 2001 was described and the connection between mine working and seismicity of this area was investigated. The energy and approximate location of the quakes and seismological parameters of the strongest ones observed from 1995 to 2001 were presented. The mechanism of the quake focuses was determined by means of the primary-arriving wave method. Stability of the slopes was evaluated by means of the Fellenius method. It has been found that seismic events occured in Belchatow region may cause only local eboulements whereas there are not any safety risks to the stability of slopes of the internal dump in Belchatow open cut.

Jan 1, 2003

Research and Technical Services, Department of Mines Western Australia The nine papers received for this technical session cover a very wide range of hydrological problems in various parts of the world. Three of these papers deal with hydrological predictions for new mines, while three are concerned with the prediction of water chemistry. The three remaining papers deal with gas injection as a dewatering tool, discharge formulae verification and the use of a physical model to predict subsurface strata movement and fracture development due to longwall mining. Hydrological problems in mine planning represent a major risk in many mining operations, booth as a potential life or equipment hazard and a major financial risk. The initial paper selected to review was therefore one by the president of a gold mining company, rather than by one of the specialist scientists, to remind us all that the main reason problems are faced and overcome in the mining industry is usually a commercial one. In one commercial undertaking, the ability to accurately assess future risk is a highly desirable planning tool and hence in mining, the ability to predict the nature and magnitude of hydrological problems is n i-an varxi imnnrfant

Jan 1, 1988

By Brady B. H

Increasingly, consideration is being given to the nominal `outcomes' of degree courses in engineering, including mining engineering. These are concerned not only with knowledge and technical understanding but also with capabilities in the professional application of engineering principles to problem solving, multi-disciplinary teamwork, communication and life-long learning. This paper discusses concepts of education, professional formation and training and the associated development of competencies in applying knowledge, understanding and technical insights and skills to new situations. In developing guidelines on preferred attributes and competencies in graduate mining engineers, a survey was conducted of a range of industry personnel involved in selecting graduate mining engineers. The results not only clarified the spectrum of competencies sought but also provided valuable detailed views to assist in defining a mining engineering curriculum. Considering a greater concern with the development of more `well-rounded' graduates, the implications are discussed with regard to teaching and assessment activities and the time demands on academic staff when a `coaching' role is emphasised. In line with international and Australian moves in engineering education, notions on education of mining engineering graduates in Australia are under review. The results will provide continuing challenges to all involved.

Jan 1, 1997

By Hart J. G, Anderson J. S

The presence of platinum metals in the nickeliferous copper ore of the Thomson River Copper Mine near Walhalla, Victoria, was first revealed in 1905 by assays made in the laboratory of the Department of Mines (1).These disclosed the presence in the ore of 5 dwt. platinum metals, 1 dwt. gold and 13 dwt. silver per ton. Attempts to isolate the platinum-bearing mineral were unsuccessful, and the absence of obvious native platinum led the assayer, Mr. P. G. W. Bayley, to suspect that the platinum might be present as sperrylite. Subsequently, Mr. C. M. Lyons, then metallurgist to the Long Tunnel Gold Mining Company, Walhalla, tried to isolate the platinum mineral from samples of ore containing as much as 7 dwt. platinum metals, but again without success.In 1912, a sample of copper matte from this ore was submitted to Messrs. Johnson, Matthey and Company, Limited of London, for analysis. The analysis, which is quoted below by their courtesy, revealed tnat a large proportion of the metal pi'eviously reported as platinum was palladium, there being about two parts of palladium in the matte to one part of platinum.

Jan 1, 1942

By S C. Dominy

A high nugget effect and the presence of coarse gold characterises many vein-gold deposits. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold. Geological complexity often compounds this effect. Underground development, in-fill drilling and bulk sampling/trial mining are often required to delineate Ore Reserves. Winzing is an historical technique that was used to gather geological and sampling data during underground exploration. It permits access to the mineralised structure below the current datum to help determine viability. Winzing has always been considered an arduous and dangerous task. Modern technology has led to the development of the Mobile Supersucker, essentially a giant vacuum cleaner. This system permits safe and efficient winzing activities, and allows the collection of bulk samples for grade estimation. Bulk samples from horizontal development have long been collected to help define mineable grade. However, when defining blocks below current development, there has been over-reliance on ineffective æsmall sampleÆ drill data. The Mobile Supersucker permits safe and cost-effective development of winzes and off-winze sublevels.

Jan 1, 2003

Mt. Whaleback, the property of the Mt. Newman Joint Venturers, contains more than one thousand million long tons of high grade hema- tite averaging 64% Fe, ranging from 70%, the grade of absolutely pure hematite, to 54%. The ore occurs in the Dales Gorge and Joffre Members of the Brockman Iron Formation. The interbedded shale bands common in other orebodies occurring in these horizons are seldom more than a few inches thick and are commonly partially enriched to about-35% Fe. In the generally hard, massive hematite orebody, the gangue minerals tend to break preferentially to the fines, or -6 mm product, and for this reason it is of a somewhat lower grade than the lumpy product. The control of the chemical qualities is concentrated on the fines product for it has been found that maintaining the iron and alumina levels in this product ensures that all chemical specifications are met in both the lump and fines products. Physical qualities are monitored to ensure that the physical quali- ties of decrepitation and degradation of the lumpy product are maintained at levels accept able to the buyers.

Jan 1, 1973

By S Pfaff, R Rajic

In the case when the number of independent variables is greater, a careful design for carrying out tests has to be made in order to obtain, with the smallest possible number of tests, as much as possible neutral information about the influence of independent variables on the dependent ones. Only on the basis of such design and its statistical analysis it is possible to come to right conclusions about the function of the whole system. The influence of pressure, temperature, humidity and granulation of the coal upon the resistance to pressure and the water absorption of the briquettes has been tested, with the aim to examine how each of the two dependent variables changes depending on the values assumed by any of the four independent variables and which of the mentioned independent variables significantly influences the dependent ones. The full factorial design with 16 experiments and the central composite design with 27 experiments have been applied. The influence of the independent variables upon the dependent ones has been examined by applying the analysis of variance. The influence values of individual factors and their interaction upon the dependent variables have been stated as well as coefficients of curvilinear equation.

Jan 1, 2003