Search Documents

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999

By A Murphy, D Lauder, J Miranda

Minera Alumbrera Limited operates the Alumbrera concentrator, treating a nominal 80 000 tpd of porphyry gold/copper ore. It is located in Argentina, 1200 km north-west of Buenos Aires in Catamarca Province, at an elevation of 2550 m above sea level. Treatment facilities consist of crushing, SAG and primary ball mill grinding circuits, rougher flotation, ball mill regrinding, gravity recovery and cleaner flotation. It is one of only a small number of concentrators in the world, which uses Jameson Cells alone for cleaner circuit flotation. Plant design was started in June 1995, with commissioning commencing in July 1997. Following a successful ramping up to design tonnages and recoveries, a number of options were reviewed to improve gold and copper recoveries. This paper concentrates on a detailed size by size flotation recovery project, commenced in May 1999. Utilising optical microscopy, scanning electron microscopy and analysis of surface chemistry it has allowed losses by size fraction to be quantified and options for enhanced recoveries to be developed. Coupled with extensive circuit surveys it has also provided an insight into previously unknown properties of Jameson Cell operation. Among these are unique residence time and bubble formation reactions to reagent and pulp flow variations, which has permitted a number of novel changes to the operation to maximise capacity and recovery.

Jan 1, 2000

By Riley S

Many regulatory bodies have, or are considering, guidelines that require rehabilitated mine spoils to be erosionally stable (satisfying quantitative limits) over specified design lifetimes. One of the problems facing the industry is that many of the computer models used for erosion assessment were developed for agricultural applications and are unable to predict the change in the shape of engineered landforms over extended periods of time. In particular, they cannot predict where valleys and gullies will develop in the landforms and how big or deep they will be. Furthermore, many existing models require considerable skill to use. A computer model (SIBERIA) developed by the first author, able to model this valley and gully development over long design lifetimes, and which is directly based on digital terrain maps is discussed here. Proposed rehabilitation strategies for waste rock dumps at Ranger Uranium Mine as assessed with SIBERIA are discussed. New features of SIBERIA of interest to the mining industry include the spatial distribution of erosion, deposition and gully development, and various measures of the quantitative risk of failure. A collaborative project with the Queensland Coal Association, involving the first author, aims to deliver these capabilities to the coal industry in a user-friendly package. The objective is the cost-effective rehabilitation of strip mines. Some preliminary results from this project are presented.

Jan 1, 1994

How often does one hear that a recent feasibility study was not a success? Alternatively, when scope of the feasibility study was sent out to tender there was a large discrepancy in tendered prices. If the tendered prices were to be compared to the consumer market, for instance the purchase of a car, where the concept is transport in a controlled and safe manner, prices vary by large factors, but then so do the specifications. In the case of a feasibility study, prices should be within a tighter margin as the tenderers are all quoting against the same concept and specification. Why do these discrepancies occur? Price discrepancies will in every likelihood be attributed to two main factors; one, the perceived amount of work and two, the ability of the bidder to carry the risk associated with the feasibility study. It is, therefore, important that the scoping of the feasibility study covers the detailed requirements as clearly as possible stating what level of accuracy is required. The feasibility study is one of the first activities in the life of a project. The study, like the project it is investigating, is subject to the constraints of time, cost and quality. Its primary objectives are to demonstrate the viability of a project within the outlined scope and constraints.

Jan 1, 1998

By Taylor GP

Mining Lease SML 57 was registered to Mount Kasi on 5 January, 1995. The Mount Kasi gold mine is located in Vanua Levu, Fiji's second largest island and operated from 1932 to 1946 producing 261,000t of ore at an average grade of 7.5g/t Au. The deposit represents a structurally controlled style of high sulphidation copper gold mineralisation with peripheral low sulphidation mesothermal vein type gold mineralisation. The resource consists of 1,048,000 tonnes of residual soils (eluvium) containing 1.9 g/t Au at 0.5 g/t Au cut off and 1,240,000 tonnes of hard rock at 3.0 g/t Au and 1.0 g/t Au cut. 94 drill holes, 298 auger holes and 85 pits were modelled to outline the resource. 29% of the pits bottomed in mineralisation and it is likely the full thickness of eluvium has been understated. The pit is scheduled to produce 500,000 tonnes of ore per annum to yield 35,000 ounces of gold with an initial 2 years of eluvial ore followed by a further 2 years of hard rock ore. Total capital costs are estimated to be less than 10.0 million dollars with construction planned to commence in 1995. The likelihood of locating further ore is high.

Jan 1, 1995

The first thing to be aware of is that the warming effect of carbon dioxide is strongly logarithmic. Of the 3¦ that carbon dioxide contributes to the greenhouse effect, the first 20 ppm has a greater effect than the following 400 ppm. By the time we get to the current level of 384 ppm, each 100 ppm increment will produce only about 0.1¦ of warming. With atmospheric carbon dioxide rising at about 2 ppm per annum, temperature will rise at 0.1¦ every 50 years for the next couple of hundred years before the effect becomes minuscule. The warming of the 20th century, as the Earth came out of the Little Ice Age, was a consequence of short, high-amplitude solar cycles. A number of solar physicists have predicted that the next solar cycle, Solar Cycle 24, will be quite weak. Based on the correlation between solar activity and the EarthÆs climate, a temperature decline of 2¦C is predicted for the mid-latitude regions over the coming decade, equating to the experience of the Dalton Minimum. Anthropogenic warming due to carbon dioxide will not ameliorate this temperature decline. Increased atmospheric carbon dioxide is wholly beneficial due to itÆs fertilisation effect. Efforts to inhibit Australian carbon dioxide emissions are exactly wrong in science.

Jan 1, 2009

In contrast to the '50s and '60s, the period of the '80s and '90s seems likely to have low growth in demand but much greater levels of technological change. In such a climate there will be pressure on costs, productivity will continue to rise and competitiveness will be closely associated with maintenance of the most effective technology. The penalties for inappropriate investments, whether short sighted or mistakenly based on a particular view of the future, will be greatly enhanced. Accordingly, there will be a need for significantly improved anticipation of technical change and thus for better planning. Study of the funding and direction of the world's R&D effort can provide a useful input to the planning processes within industries and individual firms. Such a study also suggests some insights into the characteristics of those countries which have achieved substantial growth and high standards of living over the past two decades. These characteristics may offer significant reminders for our own development. The particular implications for the Australian minerals industry include the need for direction that is sensitive to changing market requirements and customer practice. This is not simply "more of the same." In particular it appears essential for both basic and applied R&D to provide a sound basis for the purchase and ongoing development of the new technology required to achieve international Competitiveness.

Jan 1, 1986

By Lysnar R, Horswill M

Since the introduction of the pocket calculator, electronic measuring equipment, lasers and computers, the mine surveyor's approach to his work has changed. Where he once used steel bands he now uses infra-red, visible light or radio waves. The reading and storing of angles is done automatically and he now has to be familiar with the facilities that a computer can offer, instead of plotting and calculating manually. This highly sophisticated equipment is continually being upgraded, modified and fine tuned. This paper will attempt to highlight some of the equipment at present in use by the surveying profession and research currently being conducted by the WA School of Mines. The various options in EDM will be considered including the latest unit capable of measuring distance without the benefit of a reflector, thus enabling the surveyor to co-ordinate points that were previously thought inaccessible. The School is currently working on changes to the GAK1 Gyro Theodolite which may improve results and enable the operator to have more control and confidence in his observations. Areas under consideration are improved lighting, binocular viewing and interfacing the instrument to a stopwatch. In the last few years the computer is being used not only for surface pickups and control but also for underground work. We will highlight the underground options in this area and the software available.

Jan 1, 1987

In contrast with mining in areas close to the main centres, mining in remote areas is characterised by comparatively high initial investment and relatively high running cost for the life of the mine. This is because of:the real cost of establishing and running the operation at a location distant from the necessary infrastructure; and the perceived risks priced into their costs by the multitude of suppliers involved in the project. Optimal co-operation between the mine and the supplier in developing the right rela tionship and the correct technical solution permit both cost elements to be reduced. This re duction may well mean the difference between success and failure. This paper examines the possibilities for optimising the contribution of the equipment supplier to the overall success of the process. Issues covered include the necessity to provide more than merely equipment fit for the purpose , but also the need to maximise the benefits of equipment ownership over the life of the mine. A simple method of determining the optimum timing for equipment replacement or rebuilding is proposed . Furthermore the maintenance contract (or performance agreement) is suggested as a means of leveraging the supplierÆs commitment to the mining operation. The specific examples are based on experience with mobile equipment but the methodology has relevance to other equipment and supplies.

Jan 1, 1998

By Bragg R, McMahon B, Lenton R

In 1992 environmental audits were carried out at seven coal mines operated by Oakbridge Limited in the Hunter Valley and Lithgow areas of NSW. The audit reports recommended a course of action designed to improve the environmental management system already in operation at the mines. This program started with training in environmental awareness for the Board of Directors, and the development and authorisation of an environmental policy. On-going programs at each mine were expanded to include environmental awareness training for all 2000 employees at the mines, and the development of a 20-module environmental training program which included air, water, soil and noise management, oil and chemical handling, sampling and monitoring, rehabilitation techniques and many more. Environmental incident reporting was introduced, and a system of reporting from the coal face through individual mine site environmental committees, to a Corporate Environmental Committee and up to the Board Environmental Committee became an effective part of a due diligence program. The Board resolved to undertake external independent environmental audits every two years, with internal reviews in the alternate years. An Environmental Management Group was formed, consisting of four internal environmental personnel and Oakbridge's appointed environmental consultant, to effectively resolve many of the environmental issues facing the Group. This program is continuing to evolve as an industry leader in environmental management Practice.

Jan 1, 1995

Zinc produced by pyrometallurgical processing techniques suffers the disadvantage of restricted market potential because of its impurity contents, typically lead and cadmium. Market zinc to the Special High Grade (SHG) standard can only be produced by reflux distillation refining, which is costly in terms of energy and equipment, and potentially capacity limiting. Recent published laboratory work suggested that molten salt electrorefining of zinc metal is a potentially much cheaper alternative to the reflux distillation refining. The extrapolation of the laboratory results to an industrial configuration, however, resulted in an estimated power consumption for electrorefining and associated costs offering no advantage over current reflux distillation practice. A review of this estimate now shows that a serious error in calculation was made, and that the energy consumption for the electrorefining of molten zinc would be an order of magnitude lower than that for reflux distillation refining. While this is a promising indication, further research is required before development towards an industrial scale operation is warranted. This would particularly relate to the extent to which adverse electrolyte deterioration may take place and its potential effect on the anode and cathode efficiencies of the process. This paper considers the laboratory investigations required to explore the industrial potential of the molten salt electrorefining of zinc and foreshadows some of the practical problems to be solved in further development.

Jan 1, 2000

By De Cuyper J

Laboratory testwork has been performed on ancient residues from the cyanidation of a previously roasted gold-containing pyrite and arsenopyrite ore. By grinding to 95 per cent minus 60 microns, and after a strong aeration conditioning of the pulp, a gold recovery of approximately 67 per cent was obtained by cyanidation. This recovery was brought up to 80 per cent by leaching with thiourea, after a preleaching step with sulphuric acid under severe conditions of acidity and temperature. To avoid excessive capital costs bound to such processes, it was decided to investigate the possibility of applying flotation after grinding at a size similar or finer than the one used for the leaching tests. The method turned out to give interesting results because of the natural flotability observed at pH values lower than two for particles rich in gold present in the residue. After two cleaning steps, a final concentrate, representing around one weight per cent of the feed, was obtained with an approximate gold content of 350 g/t, representing a batch recovery of gold of about 50 per cent. Apart from sulphuric acid, whose addition was very high (flotation slurries at 25 g/l H2SO4), other reagents were not found necessary. Additional flotation tests were carried out to examine whether the recycling of the cleaner tails was justified but the gain observed appeared insufficient.

Jan 1, 1993

This paper discusses the significant land use changes that have occurred in the Latrobe Valley during 150 years of white occupation. The developments and changes were haphazard and made with little thought as to their setting or their environmental consequences. As a result many landscape and land management problems have not been addressed.This paper contends that the mistakes will continue unless an overall plan for the landscape of the area is developed and implemented. The concept of 'Greening the Valley' is introduced. It aims to provide focus for a comprehensive co-ordinated plan which caters for the need to restore the landscape and the need to provide for future land use. The plan will seek to draw on three major landscape features of the Latrobe Valley: the natural setting of the hills, rivers, valleys and forests; the agricultural land use including the forestry plantations; and the industrial complexes and urban areas.Rehabilitation of mining areas is a key element of the plan but must be put in a regional context and not be treated as an isolated function of a single organisation. A major challenge will be to integrate the worked out areas into useful and significant landscapes. The paper concludes by explaining the process that will be followed in an attempt to realise the concept.

Jan 1, 1992

Pyrite is one of the principal Au-bearing minerals in refractory gold ores. Significantly high Au concentrations of up to 5200 ppm are present in pyrite. Pyrite hosting high levels of Au is also enriched in As. Pyrite as an unwanted mineral ends up in wastes and constitutes one of the primary sources of As in the mining and metallurgical wastes. Arsenic can be readily released to the environment due to rapid oxidative dissolution of the host pyrite under atmospheric conditions. In order to determine the form and occurrence of arsenic in pyrite, micro-X-ray absorption fine-structure spectroscopy (XAFS) spectra were collected from a range of arsenical pyrite grains having different morphologies and a range of arsenic and gold concentrations. All the pyrite grains are characterised by the dominant edge aligned with As-1 valence state. In pyrite, arsenic atoms substitute for S atoms that are in six-fold coordination about each Fe atom. XAFS data suggest that As atoms occur in clusters within the pyrite structure. In addition to As-1, fine-grained, inclusion-rich and framboidal-type pyrite grains have a second As species at ~11 875 eV corresponding to As5+. This As5+ species in pyrite is highly variable and attributed to the oxidation of arsenic exposed on the surfaces of pyrite.

Jan 1, 2008

There have been many developments in recent years in pipeline transport to enable them to be more widely used in industry. Substantial tonnages of materials that are not affected by water, such as coal and other minerals, aggregates and wastes, can be moved over considerable distances in quite small diameter pipes. Where there are no existing road or rail facilities, long-distance pipelines are usually cheaper to install, and this advantage increases in difficult terrain. Pipeline operators all over the world assert that hydraulic lines pay for themselves in a relatively short time, in spite of the heavy capital outlay, and this is equally true for lines convey-ing slurries or pastes within a plant complex.'This paper reviews some of the more important investigations in the hydraulic transport field. Although reference to systems carrying a wide range of materials is made, the majority of recent published data centres on coal transport.The paper looks at the application to a wide range of particle sizes, the development of non-aqueous slurrying media and coal/water fuels. The review also looks at some of the equipment being proposed to provide more reliable operation and in particular the range of solids-handling pumps now available.-The paper goes on to identify areas where further research and development is required and some of the many organisations undertaking this work.

Jan 1, 1985

The Ausmelt Catalytic Waste Converter (CWC) has been developed for use in the treatment of industrial wastes and for the recycling of secondary materials. Ausmelt Technology uses a top submerged lance system within a versatile and efficient slag bath reactor. High temperature pyrometallurgical reactions are carefully controlled within an oxidised molten siliceous slag such that metals can be extracted from waste feedstock for recycling, with non-volatile elements reporting to the slag, usually as oxides. Modification of the slag chemistry results in a final slag product that is stable, vitrified and is able to pass standard leach tests such that it is safe to discard or be used in civil engineering applications. Toxic components in the wastes such as organohalides can be completely destroyed and are prevented from reforming. Waste to energy conversion is practiced by the addition of a heat exchanger/steam generator in the converter offgas system. The Ausmelt CWC has been used for recovering zinc from residues and slags, treating spent potliner (SPL) from the aluminium industry and a wide range of electronic and other potentially valuable waste materials. Methods of monitoring the exhaust gases at different stages in the CWC gas handling system are discussed. The assay of these gases prior to emission is used to assist in the control of the converter chemistry to ensure the complete oxidative breakdown of the feedstock.

Jan 1, 2002

By C P. Kramers

The need to provide a sufficient quality and quantity of backfill continues to increase in South Africa, particularly as related to the increasing depth of mining. More and more applications require well designed fill systems either as classified or cemented backfill, and in some applications even tailings/aggregate based backfills. The paper discusses developments in backfill technology in South Africa with special emphasis on reliable system designs and operations, particularly as related to the preparation and hydraulic transportation aspects. Approaches for the alleviation of previous problems associated with premature pipe failures in vertical shaft columns for the distribution of tailings based backfills are discussed. Resulting from CSIRÆs developmental work, reliable full-flow systems, which can operate at low system pressures, have become a common practice, provided that backfill flowrates and internal pipe sizes are well matched. This aspect is reviewed. With regard to the tailings/aggregate based backfills the paper reviews some of the results of comprehensive in situ monitoring and the development of such systems. It is shown that a thorough understanding of the effects of aggregate top size, fines content and slurry relative density is required in order to ensure the restartability of temporarily shut-down pipelines. Some innovative technologies for the comminution of development waste underground to yield aggregate products potentially suitable or hydraulic transportation and backfilling, are briefly discussed.

Jan 1, 1998

Mining projects draw together stakeholders with various degrees of experience in managing and assessing financial risk. When this risk is not fully appreciated or quantified, the potential for making decisions not suited to investor requirements is significantly increased. A feasibility study provides key information on project development potential, requiring detailed technical investigations with thorough financial analysis. Centaur Mining and Exploration (CME) owned and operated Cawse Nickel Operations (CNO), one of three Australian projects to develop and process vast amounts of near surface nickel resources. A technical ædue-diligenceÆ and æbankable feasibility studyÆ confirmed the large resource base, newly applied yet tested technology and relatively low unit costs would produce nickel in the lower half of industry operating costs. A number of production variables including capital requirements, delayed start-up, nickel grade, processing, maintenance and product output were outside the feasibility estimate. This was combined with exchange rate fluctuations and lower Ni prices. The inability to generate adequate cash flow and service debt repayments ultimately led to receivership and liquidation of all assets. Following the sale of CentaurÆs gold and nickel divisions, $A 784 million remained outstanding to creditors. This paper aims to define key issues leading to CNOÆs collapse by reviewing feasibility parameters, valuation methodology and project development. Some methods of assessing project viability are discussed with the aim of increasing stakeholder risk awareness.

Jan 1, 2003

By Voorhees JS, Bureau G

To operate a mine in California requires compliance with State environmental regulations, including assessment of risks and associated financial assurances for postulated worst case catastrophic event scenarios. Carson Hill Gold Mine, an open pit, heap leach operation, completed new risk assessment catastrophic event analyses in 1988. The risk assessment was performed at the same time that a new leach site (Leach Site 3) was being designed. Leach Site 3 is located about 400 m upslope of New Melones Reservoir, which is a public recreation facility and a source of drinking water. Release of leachate (pregnant solution) or ore containing cyanide and metals from Leach Site 3 into New Melones Reservoir was considered to pose the largest risk of environmental damage.Flow failure of the ore heap, potentially induced as a result of liquefaction of the saturated portion of the ore, and/or overtopping of the leach site containment embankment due to excessive precipitation were found to be the most plausible leachate release scenarios. Yearly combined probabilities of various downstream release volumes were estimated. The release volume corresponding to a yearly probability of 0.05 percent was then used to estimate potential environmental impacts and mitigation costs. The costs include earthwork to restore the geometry of the ore heap and repair the fill slope below the Leach Site 3 containment, and impacts on New Melones Reservoir.

Jan 1, 1990

By Loo R

The Paper discusses the size and extent of in-pit dust suppression problems created by iron ore mining in the Pilbara region of Western Australia. Dust problems associated with drilling, loading, hauling and tipping are discussed indicating the large quantities of water which can be applied for dust control and attempts that have been made to rationalise this water usage to obtain maximum benefits from the applied water. The magnitude of the problem and the quantities of water involved can be appreciated when one realises that 275 000 tonnes of rock are moved on Mt. Whaleback each day and that there are 40 km of haulroad within the open pit. Initially dust suppression was limited to the spraying of haulroads by large water tankers. Now dust suppression is practiced during drilling and after blasting, wind blown dust is reduced by application, using water cannons,of large quantities of water to floor stocks prior to loading operations as well as by the installation of 16 km of automatically controlled fixed sprinkler reticulation on the main semi-permanent haulroads. The methods used to assess the water requirements for in-pit dust suppression are discussed and the extensive development testing used to evolve the present installations are 1. Environmental Superintendent Mt. Newman Mining Co. Pty. Ltd. Newman, W.A. 2. Chartered Consulting Engineer, Perth, W.A.

Jan 1, 1979