Search Documents

The introduction of cement into underground backfilling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines to improve mining efficiencies gave rise to several major problems, the magnitude of which had not been anticipated. These problems were 1. A loss of recovery in the milling circuit due to the presence of cement 2. The presence of cement-rich slime layers on the surface of the fills 3. The introduction of a safety hazard due to the slippery nature of the surface of cemented fills 4. The deposition of cemented slimes on the levels and in underground sumps and dams. The loss of revenue due to decreased metal recoveries considerably offset the gains from increased stoping efficiencies and the use of cement was substantially reduced while, (a) the Metallurgical. Department attempted to identify the chemical nature of the problem and overcome it, and (b) the Mining Department investigated methods of reducing cement contamination of the ore stream. As a part of this investigation the Mining Department added polymeric flocculants to the cemented fill pulp. Testwork was carried out in the following steps 1. The available Alfloc polymers were screened to determine which was the most effective and what was its optimum dosage rate. 2. This polymer was used in the laboratory to determine the reduction of surface slime, clarity of water, and effects on strength and percolation of fill. 3. Fills were placed underground to substan- tiate the laboratory work. /+. The polymer was then added to all cemented fills going underground to study its effect over a long term. The use of flocculants not only improved the distribution of cement in the body of the fill, but also the distribution of the fines fraction of the filling material, practically eliminated slippery surfaces and improved the clarity of the drainage water. Flocculant is now added to all cemented fills and restrictions on the use of cement are gradually being lifted.

Jan 1, 1973

By K Gottliebsen

Many hydrometallurgical and chemical processes produce large amounts of acid waste. This is illustrated by the copper S/X-E/W process used at the Mount Gordon mine in North Queensland, which produces a tank house bleed in the form of a concentrated sulphuric acid stream. The bleed stream is necessary to remove impurities such as iron that decrease the efficiency of the electrowinning process. However, this bleed stream comes at a high financial cost due to large quantities of make up sulphuric acid required as well as the need to neutralise the bleed stream prior to disposal. The present work describes the approach taken to develop a solvent extraction process for the selective recovery of sulphuric acid from copper tank house bleed liquor. The proposed extraction system was investigated using a branched long chain aliphatic tertiary amine tris(2-ethylhexyl)amine (TEHA) as the extractant, Shellsol 2046 as the diluent and octanol as a modifier. Computer simulations were used to determine the optimum operating conditions for the recovery process. It was found that the process was able to selectively recover up to 90 per cent of the sulphuric acid from the copper electrolyte. This is recovered as a pure aqueous acid stream at a concentration of up to 130 g/L that can be recycled back into the tank house circuit or other areas of the process. The raffinate acid concentration was reduced from 180 g/L to as low as 18 g/L, significantly reducing waste disposal and the environmental impact of the copper process. The equilibrium data and simulation results were also compared with an alternative extractant, CYANEXR 923. Finally the efficiency of the TEHA extraction system was investigated on a pilot-scale in a pulsed perforated plate column. This information was used in order to scale the process for an industrial application. The same methodology applied in this case study could be used to provide innovative and cost-effective solutions to waste streams encountered in other hydrometallurgical or chemical processes.

Jan 1, 2000

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2008

By D C. Franklin, C T. Farrelly

The future of human exploration in space is intimately bound to the future of mining and energy production on Earth. By 2025, one or more manned bases will probably exist on the Moon, exploring the lunar landscape and geology, and acting as a learning platform, and possibly a resource platform, for expeditions to Mars and beyond. Unless the mining and space industries take an active and cooperative interest in the technologies required to exploit minerals and fuels in and from hostile environments, the necessary advances to support permanent extraterrestrial exploration will not be ready in time. With the notable exception of using lunar Helium-3 as a fusion power fuel, no other reason has been identified for the mining industry to take any direct interest in the exploitation of extraterrestrial resources for the benefit of its customers on Earth. Ample reasons exist, however, for the industry to take a direct interest in supporting technological development of the extraterrestrial resources necessary to support the economical exploration of space. The mining industry has critical experience in the development and application of technologies for the discovery, extraction and processing of natural resources; experience that the space industry will need to create a viable permanent presence in space. The industry also understands the end to end process of resource development and utilisation. On the other hand, the space industry can directly benefit the mining sector by helping mature and advance the extractive and processing technologies needed to economically and sustainably develop resources in hostile terrestrial environments, such as those available in low concentrations, at extreme depth and/or inconvenient geographic locations. We propose that strategic partnerships be created between the mining, space and allied industries and research organisations. Such partnerships would develop a joint capability for mutual benefit, targeting the most significant advances in the least time. The space industry will learn how to exploit essential resources off-planet, and the mining industry will gain access to technologies to help extend their activities on earth.

Jan 1, 2008

The total cost of horizontal development can be minimised by optimising the cost of each of the component operations (eg drilling, blasting, etc). Component costs should not be minimised. To optimise blasting results (ie the mean advance per round, muckpile characteristics and overbreak), operators need to optimise the blast design and drilling and blasting procedures. The costs of pulling extremely long (say >6 m) rounds, producing unnecessarily fine fragmentation, and minimising overbreak are excessively high. Operators should continually consider how they can shorten the cycle period by saving time at the face. To enable it to be matched to the pertinent rock properties, the blast design needs to be based on as much relevant experience as possible. To develop the most valid correlation between blasting results and blast design, the latter must be implemented carefully and accurately, but without sacrificing speed excessively. The total cost can often be reduced by using: 1. computer-controlled jumbos (to reduce the period and cost of drilling and to increase drilling accuracy); 2. larger diameter (51 mm to 64 mm) and longer (4.5 m to 6 m) blastholes; 3. at least three large diameter ( ¦89 mm) relief holes that are 0.2 m to 0.3 m longer than the blastholes; 4. explosive products that are selected on the basis of proven reliability and overall cost efficiency rather than price; and5. stemming (to increase the amount of effective work done by each kilogram of explosive and, hence, to reduce the powder factor and possibly the number of blastholes and the costs of drilling and initiation). Non-perimeter blastholes should be charged with ANFO or a bulk emulsion of established performance. Upper perimeter blastholes should be charged with a bulk explosive with a much lower effective density. But where geology varies considerably, greatest control over overbreak could possibly be achieved with the versatile pre-assembled charge shown in Figure 1. This paper presents numerous potential ways in which the total cost of development can be minimised. It concentrates on recommending blast design features and the safe, rapid, cost-effective implementation of designs.

Jan 1, 1998

By C A. Foss, K Blay, K Leslie, D Hillan

Magnetic field studies provide remote sensing of magnetisation distributions and a means to investigate moderately- to strongly-magnetised ore deposits that may be partially or totally buried. However, above-surface magnetic field surveys have limited capability to resolve the detail of magnetisation distributions because of the large separation between the magnetisation and the magnetic sensor. While some of this detail is available from magnetic susceptibility logging within boreholes or from magnetisation studies on recovered core, these measurements are limited to the exact trace of the boreholes. The large disconnect between ground or aeromagnetic surveys and highly-localised borehole sampling can cause problems in developing robust source models from magnetic survey data. The measurement of magnetic field in boreholes has the capacity to at least partially bridge that gap by measuring the magnetic field due to magnetisations proximal to, but not intersected by, the boreholes.CSIRO has developed the world’s first downhole magnetic tensor gradiometer. This instrument measures magnetic field gradients in all directions within a borehole. A prototype instrument has been built and tested as part of phase 1 of the Deep Exploration Technologies Cooperative Research Centre (DET CRC). The prototype performed well with magnetic pyrrhotite at the DET CRC test site in the Adelaide Hills and at Carpentaria’s Hawsons magnetite deposit south of Broken Hill. Further work is required to reduce the diameter of the probe so that it can operate in NQ holes (it is currently limited to HQ or wider) and to transform it to a continuous logging tool. The borehole tensor gradiometer can be used to investigate the continuity of magnetisation over a distance of several metres to tens of metres away from a borehole intersection and the structural dip of the magnetic body. It can be used to either replace or augment downhole magnetic susceptibility logging. This instrument is one component of an integrated CSIRO suite of new magnetic field utilities and methodologies for iron ore exploration and development.CITATION:Leslie, K, Foss, C A, Hillan, D and Blay, K, 2015. A downhole magnetic tensor gradiometer for developing robust magnetisation models from magnetic anomalies, in Proceedings Iron Ore 2015, pp 299–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The Porgera gold project is now in its seventh year of operation as one of the world's prime gold mining projects in one of the most underdeveloped and remote regions of the world. The unique gold deposit was development in stages to its present size of operation with an underground mine of 2000tpd, an open pit operation moving 210,000tpd and a complex metallurgical plant treating an average of 16,500tpd of ore. During the past years the operation had to address an array of issues relating to the "development" of the region and this is still ongoing. Development means different things to different people and though the parties that signed the different agreements relating to the Mining Development Contract were aware of this, none has real- ised the extent to which this is true. The developing company (a joint venture between Placer Pacific as the Manager, Goldfields Porgera, Highlands Gold and the Government of PNG), provided funds for risky exploration and the capital for development of the project. Its shareholders ex- pect an economic and viable mine operation from the deposit to ensure them returns on their investment. The local people gave up their land, their isolated way of living and accepted to be out of their comfort zone for some time in anticipation of a better lifestyle and economic benefits in support of that lifestyle. The PNG Government has a leg in both camps and expects both outcomes at the same time. The Government is also the regulator and expects compliance on top of that. If development in general is to be successful, all parties must substantially satisfy all expectations. It is evident that the outcome of some elements of development are reasonably defined (i.e. develop a viable mine to exploit the deposit), whilst other elements are moving targets (i.e. a better lifestyle). The seeds for conflict are thus abundantly present and to resolve them requires the will of all parties in all areas to come to a solution. This path to problem solving is many times torturous as each party comes from a different culture and background and has a different understanding of the parameters in the equation.

Jan 1, 1997

By C Yeung, N Swa, D Gribble, R Reupana

BlastLiteÖ is a low density explosive developed by Dyno Nobel and has been in use at BHP Billiton Iron OreÆs Mt Whaleback Operation since March 2004. The Mt Whaleback Operation utilises BlastLite because it offers an attractive alternative to ANFO in soft to medium strength rock types. Its use also reduces the amount of liquid fuel oil consumed and is well aligned with BHP BillitonÆs corporate Energy Excellence initiatives to reduce greenhouse gas emissions. This paper presents the:results of characterisation work completed on-site as a fourth year mining engineering thesis, and application and benefits of the product at Mt Whaleback. One of the key features of low density products is that the detonation is non-ideal. That is, the explosive does not react fully in the detonation driving zone. This manifests itself in that the product is highly dependent on charge diameter and confinement conditions. Dyno Nobel has access to the Vixen suite of detonation codes for characterising the ideal and non-ideal behaviour of explosives. The objectives of this work were to use the Vixen_i code to characterise the detonation performance of BlastLite, in order to understand the role of the bulking agent and to allow modelling of the explosive. The detonation performance was established by detonating a series of unconfined charges at various diameters and measuring the velocity of detonation (VoD). The work program consisted of sourcing and preparing cardboard tubes of various diameters (80 mm to 305 mm). The tubes were loaded with explosive at the BHP Billiton Iron Ore Mt Whaleback test range and detonated one at a time. Over the past three years BlastLite has been used in various applications across the site. Initial findings illustrate that shovel productivity from BlastLite shots was comparable to the baseline ANFO blasts. The study results were also backed with visual inspection and feedback from shovel operators. A work program is currently in place to develop different blends of BlastLite and TITAN« BlastLite to tailor the explosives to various blasting applications. The trials at Mt Whaleback are leading to future opportunities of BHP BillitonÆs satellite orebodies.

Jan 1, 2007

Rock bolting and rock-bolting systems depend for success on attention to a number of simple techniques. Failure to appreciate this fact can lead to disappointing results. Careful study of rock characteristics and placement methods can allow a change to highly successful rock bolt per- formance. A number of examples are quoted to illustrate the sig- nificant improvement in results which can be achieved by use of the most suitable combination of characteristics.

Jan 1, 1971

By H R. Phillips

Fresh air intake in an underground coal mine is of critical importance to the occupational health and safety of workers due to the dynamic, confined and dangerous nature of the mining environment. In most coal mines in South Africa, belt road is not separated from the fresh air intake to the sections. Intake air to coal production faces generally contains dust generated by conveyor belts, transfer points and travelling roads. Long roadways (up to a few kilometres in some of the existing mines) to the coal sections are involved in the ventilation circuits of individual sections. This leads to a progressive increase in the dust levels in the intake fresh air and thus high dust levels in the air delivered to the working sections downstream. In the process of reducing worker exposure to dust in the face area, attention to the monitoring of fresh intake air is generally given a low priority. This paper summarises the intake dust levels measured in selected South African underground coal mining sections over the past five years and its use as a parameter in assessing worker exposure to dust through a newly developed model called the Dust Exposure Level Index (DELI). Based on the measured data of the South African coal mines, the average section intake dust level was 0.78 mg/m3. Approximately 60 per cent of the samples collected for the study have exceeded the 0.5 mg/m3. The intake dust level measured at a longwall face was much higher than in the CM headings. The measured section intake dust levels furnish the South African coal mining industry with the latest depiction of the level of face area dust contamination due to the intake air. Further, this paper demonstrates the use of intake dust level as a parameter in estimating exposure levels of workers, as it clearly plays as a corner stone in effective control of exposure to face area respirable dust. It must be borne in mind that intake dust is a base level to the mine worker exposed to dust without carrying out any additional work in the section. If the intake air is seriously contaminated by airborne respirable dust; then the exposure of the workforce in the section will constantly be elevated by that background dust level.

Jan 1, 2005

By D Wiseman, R Dunne

Flash flotation is a process that is included in many new mineral processing plants as part of the grinding circuit. Some of the valuable minerals can often be liberated at coarse sizes and will remain in the recirculating loads of the mill until they are reground small enough to report to the cyclone overflow. In addition, minerals of high density report to the cyclone underflow despite being fine in size. This can lead to overgrinding and makes the recovery of valuable fines by flotation difficult. Flash flotation is used to remove the readily floated coarse particles as early as possible and can therefore prevent overgrinding. It thus has the added potential to improve materials handling of the concentrates in such processes as filtration. The merits of including flash flotation within an integrated comminution-conventional flotation circuit is not easy to determine experimentally. Simple batch flotation tests are unable to provide any measure of the possible or probable improvements that are likely to occur from this circuit configuration. As a consequence expensive pilot plant programs are resorted to, to provide the information that will justify the inclusion of flash flotation into a comminution-flotation circuit. Those who have been involved in such pilot plant programs will know of the difficulty in stabilising the circuit as well as selecting the appropriate operating parameters (eg amount of concentrate to be removed in both the flash flotation and conventional flotation circuits). The interactive nature of this circuit (grinding, classification and flotation) is the root cause of these difficulties. Computer simulation, based on information derived from laboratory batch test work or plant and laboratory data, offers an alternative means by which an initial assessment of the merits of a flash flotation circuit can be determined. It can also provide the basis and focus for pilot plant testwork. Recently MacKinnon, Yan and Dunne (2003) developed a model that allows the performance of a flash flotation to be obtained within a closed circuit grinding operation. This paper provides details of an extension of this model to incorporate the interaction of flash flotation on the downstream conventional flotation circuit and allows æwhat ifÆ scenarios to be explored. Details of the laboratory batch test work methodology and the pertinent data derived from these tests that are used in the models and simulation are provided.

Jan 1, 2005

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

The safety culture in mining has progressed towards a zero tolerance of injury. This change has required that some historically inherent risks of mining are engineered out or reduced. One of the significant causes of fatality in Western Australia and Worldwide mining is through rock fall, subsidence and inrush. Efforts put into understanding the material properties of the ground we mine and the backfill we place are reflected in improved safety statistics. It is no longer acceptable to not manage these risks and mining, to be sustainable, has to be safe.   Mining historically produced waste products with little consideration of recycling or impact on the surrounding land. The rehabilitation of mining waste products such as mill tailings, heap leach and waste rock is one step towards managing the environmental impact of these waste products. A better step is towards recycling and redepositing these products to produce a more environmentally sustainable mine site.   Gold fields St Ives lease is an active network of new and historic undergrounds and open pits within the Lake Lefroy and Kambalda district. The process of creating voids underground followed by open pits mining through the old voids allows the use of backfilling to control inherent hazards and dilution. Backfill provides opportunity for the disposal and recycling of mining waste materials at the same time as meeting requirements of mine support. Materials available on the St Ives site include spent heap leach, reclaimed tailings and waste mullock. Through recycling and re-depositing these materials to St Ives and neighbouring mines, the reliance on imported material to meet their needs and impact on surrounding land is reduced.   At St Ives, paste fill and barricade design have been reworked to allow backfilling into stopes with water inflows up to six litres per second. This has required a rethink of the drainage and monitoring of water management systems previously used for hydraulic fill and apply them to paste.   The St Ives open pits have developed methods to mine through underground workings and individual stope voids up to 62,000m3. Here backfill is used to reduce the consequence of catastrophic, unexpected failure of the crown and minimise ore lost down voids and dilution through increased blast movement. This paper outlines the less common methods being adopted to use the recycled materials and ways it has been managed to suit the needs of the company.

Jun 1, 2010

This paper aims to address the issue of the public's image of the extractive minerals industry. What is it about the industry that incites such negative feelings and are they justified? Are we really the 'rapists of the land' that many would have us believe? Has the industry really not improved since the old gold boom days?   I believe that the fundamental cause for the public's view is lack of knowledge and understanding of the industry as a result of the dislocation of the end production from its source. There are few people who look at a house, car, record, toilet, tooth-brush, bottle of coke or pair of glasses and see the mine site that supplied the source material. But the mine site and its products should be inseparably linked. This is one area where we should be educating the public û it is all very well being anti-development but the population as a whole is not really prepared to live without its 'mineral'-derived necessities. It is very easy to say that we do not want minerals development in New Zealand but are we prepared to live with the consequences, ie go without its products? We have a duty as a global citizen to develop our own resources rather than expect Third World nations desperate for overseas investment, often with governments who are not prepared to constrain or control their development, to be exploited. New Zealand is not the only 'beautiful' place in the world and we should be aware of the impact that our demands for resources have on the countries who supply us. We have a duty to be a good global citizen.   So how does the industry improve its public image? The key here has to be to educate. This does not have to be high powered or expensive but can be as simple as getting a few local kids' hands dirty panning, and gaining some firsthand knowledge of the industry. The industry also needs to be more pro-active in the public arena. Yes, the industry has skeletons, but the industry should be publicly displaying them û admit that things have gone wrong but let's do it ourselves and not leave it up to the environmental groups to accuse, point the finger and put the industry under public scrutiny. The industry should also be publicising its successes, inviting the local press, councils, etc to view the latest area rehabilitated. But more than anything else we must tell the public what the minerals industry means to New Zealand. Can they really live without us?

Jan 1, 1991

Presidential Address Today I want to couple that prediction with a discussion on competitiveness and changing employment roles in our industry. A crude analysis of the intensity of use of metals in developed and undeveloped nations was undertaken by dividing the weight of copper, zinc, lead and aluminium used in countries by the population. In the developed countries which were basically the Western European States, USA, Canada, Australia and Japan, approximately 38 kilograms are used per annum. In the developing countries which were basically the South-East Asian country Korea, India, Pakistan and Taiwan, the usage is 5.3 kilograms. Thus, if the developing world is to catch up with the developed world, the intensity of use of metals will have to increase seven times. The usage of metals in the developed world is increasing at the rate of 1.5 per cent per annum while the rate of increase in the developing world is about 5.8 per cent. In this analysis, the population of the developed world was 850 million and the developing world 1.5 billion. Note that this analysis did not include Russia, China and most of the countries of South America and South Africa. I am sure that with time, these undeveloped countries will move into the developing category. In the long-term there is obviously great opportunity for us both in the primary and secondary processing required to meet world demand. Turning now to competitiveness and changing employment roles. I am sure that everyone here present is aware of the urgent need for Australia to improve its competitiveness. I want to try and relate unionism and industrial relations, management and tertiary education to our competitiveness. I wish to talk on these items as I see them in the past, the present and the future. So firstly unionism and industrial relations. It has been unfortunate for Australia that unionism was based on the United Kingdom craft system. It is not surprising that it was because UK has been the basis for almost ' all of our institutions and that has generally been of very great value to us. The craft system in our trade unions has lead to the demarcation problems of which we have all been well aware. This has been extremely limiting to the individual; it has limited his or her ability to broaden their scope of knowledge and far worse it has limited their ability to maximise their satisfaction at work as they have only been able to undertake part of a job, rather than being able to undertake a role in totality.

Jan 1, 1992

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

By E Nettleton, A Melkumyan

Identification of geology and mineralogy in situ on the mine face is essential if mining processes are to be automated for tasks such as exploration, grading and reconciliation. Hyperspectral data acquired from field based platforms are ideally suited to these tasks, and are set to revolutionise the automated mining industry. Changing conditions of solar illumination introduces variation into the hyperspectral signal, which is unrelated to geology, complicating analysis of data. Thus, algorithms must be able to deal with changing illumination conditions and operate in a consistent and probabilistic framework, which is a prerequisite for data fusion with other sensors. To produce accurate classification maps of geology, algorithms must be developed that are effective under different conditions of illumination.The efficacy of three algorithms to classify hyperspectral data for geology mapping on vertical mine faces was assessed. These algorithms are the spectral angle mapper (SAM), and two machine learning methods operating within a fully probabilistic Gaussian process (GP) framework û the squared exponential (SE) and the observation angle dependent (OAD) covariance functions (kernel). Two experiments were done to assess the classification performances. The first determined the performance of the algorithms by classifying hyperspectral data of known rock samples acquired using a field spectrometer. The GP-based methods had a similar performance, with average accuracies and F-scores of 97 and 88 per cent (GP-OAD) and 95 and 81 per cent (GP-SE), respectively. Average accuracies and F-scores for SAM were significantly smaller (80 and 40 per cent respectively). The algorithms were then applied to hyperspectral imagery acquired from a vertical mine face at different times of the day, under very different conditions of illumination. In contrast with experiment 1, SAM and GP-OAD gave results which were superior to GP-SE and were entirely consistent with geology mapped in the field. Compared with SAM, GP-OAD was less sensitive to the effects of shadow and produced classified images that were less noisy. The GP-SE method failed to delineate even gross changes in geology on the mine face. These results show conclusively that in order to use independent training data (spectral library) to classify imagery acquired under a different set of conditions, algorithms must take into account variability in incident illumination. Measures based on spectral distance are inferior to those based on spectral angle.The OAD kernel within the GP framework (GP-OAD) is superior to the other two methods because:it provides a probabilistic framework;it is insensitive to variability in illumination within and between imagery acquired under different conditions; andit can identify and map geological zones on a vertical mine face using an independent spectral library, without a priori knowledge.

Sep 26, 2011

Mr. Chairman, Distinguished Guests, Ladies and Gentlemen. I was delighted to be invited, and to accept the invitation, to welcome to this specialist meeting on an intriguing subject, the local participants and - most importantly - the international contributors. Technical o analysis of blast furnace operations has for many years formed the basis of intense research throughout the iron and steel industry, world wide, because the efficiency of blast furnace operation estab- lishes the foundation for all subsequent processes in a steel plant. So much depends on the constant, efficient performance of iron melting units in relation to costs, quality, regularity of operations and reli- able delivery performance to our customers.

Jan 1, 1981

The role of marketing in the development of a new project will be affected by political, commercial and technical pressures. Marketing success will be determined by the ability to predict and react to tomorrow's environment. In the Australian coal industry there is an emerging transition from production to marketing orientation. As a result, greater technical awareness of customer needs will be required. In particular, the industrial product nature of coal markets will need to be recognised. Greater attention will also need to be paid to product options and quality in mine planning. Marketing personnel will become more involved at every phase of the development of a new mine.

Jan 1, 1983

A new approach to strategic planning, the Life of Business Optimisation System (LOBOS) optimises production systems from the scale of stopes in a single mine to an entire business strategy consisting of multiple mines and products competing for capital and processing capacity. LOBOS has optimised cash flow for a wide variety of operations, including large metalliferous or coal mines and as an aid to high-level strategic business optimisation solution to multi-mine/processing/product complexes. This paper discusses the application of optimisation technology to strategic planning with an emphasis on project evaluation with examples on the application of LOBOS to a variety of recent projects.

Jan 1, 2007