Search Documents

By Tobin GJ

Testwork carried out in the cooling water circuit at the Yabulu treatment plant of the Greenvale Joint Venturers (Metals Exploration Queensland Pty. Ltd. and Freeport Queensland Nickel Incorporated) since 1980 has resulted in significant improvements to both fouling and corrosion control. At the same time corrosion inhibitor costs have been reduced.Acrylate-type silt dispersants were identified as the most effective means of sediment control in the circuit. An increase in the cathodic component of the corrosion inhibitor coupled with a relatively minor adjustment to water pH has yielded a two to three fold reduction in corrosion rate. It has been established that these lower corrosion rates can be sustained in the face of a 20% reduction in corrosion inhibitor addition rate. Further improvements are indicated with a change of raw water algicide.

Jan 1, 1985

This paper covers the key issues such as orebody geometry and grade, geotechnical data and metallurgical response. These must be considered in selecting a mining system for a new orebody. It then focusses on the advantages of open pit mining over underground mining particularly in the areas of costs, speed of development and safety. Environmental issues with waste storage is the only negative which emerges. Consequently, the majority of new large mine developments continue to be open pits. It is also demonstrated that underground mining continues to play an important role, particulary for high-grade deposits at depth. The impact on ore recoveries of recent developments in stabilised fill technology in underground mining is also highlighted. The importance of economics to the decision on mining method is continually emphasised as maximising orebody value should be the prime objective of this Work.

Jan 1, 1997

By Laffin N. W

Invariably when a new plant is cammissioned operations personnel on takeover look at ways and means of reducing certain restrictions and improving process conditions. These improvements are generally of a mechanical/engineering nature with minor metallurgical alterations to fine tune and maximise recovery. Most operations are continually reviewing and updating existing equipment and equipment spares to gain the maximum performance hereby reducing operating costs. Design of current carbon-in-pulp/carbon- in-leach (CIP/CIL) plants has evolved to such a high degree that many of the medium sized plants can have a "blue printed" design from one to the next if the same engineering designer is used.

Jan 1, 1989

The selection of an appropriate mining method should take into account the geometry of the deposit and its physical properties. Other factors which assist in the determination are the requirements for flexibility in the mining process, minimisation of risk factors and maximising the financial return. Several established mining methods exist which can encompass the requirements to deliver the optimum mining method, this can be in both an underground or open cut environment. The objective is to outline these methods and where they can be applied in a mining project.

Jan 1, 1997

By Alwan M

At Binebase mineralisation is hosted within an andesitic Neogene volcaniclastic succession on Sangihe Island, Indonesia. Two major alteration types occur; an initial widespread phyllic assemblage of quartz -illite with chlorite, smectite, gypsum and pyrite, and a superimposed quartz - barite - sulphide assemblage. The phyllic alteration arose from a neutral to weakly acidic hydrothermal solution of greater than 200 degrees C, and the quartz - barite - sulphide assemblage arose from a cooler slightly more acidic fluid. This second alteration event is interpreted to have selectively replaced permeable volcaniclastic breccias and coarse lithic tuffs within the altered sequence. Gold and silver mineralisation is associated with the latter alteration, and is locally controlled by the degree of silicification and sulphide abundance. The sulphides present are pyrite, covellite and chalcopyrite. The sulphides are very fine grained with colloform and framboidal textures and were deposited contemporaneously with the bulk silicification of the coarse sediments. A large portion of the mineralised rock has been oxidised to a quartz - barite -limonite - goethite - jarosite assemblage.Coincident gold, silver and antimony geochemical soil anomalies gave the best correlation with anomalous gold and silver grades in bedrock as identified by drilling. Resistivity proved a reliable geophysical method for delineating zones of silicification.

Jan 1, 1990

By Sjaw WJ

Conditional simulation is a set of geostatistical tools that is becoming popular as powerful personal computers make the use of these tools less costly. The more familiar set of tools for spatial estimation has a number of varieties (eg Ordinary Kriging, Simple Kriging, Multiple Indicator Kriging, etc) each suited to particular solutions of the problem of estimation, for example predicting the average grades of blocks in a region from more or less sparse data. Similarly, conditional simulation has a number of varieties, discussed in this paper, which in various ways address the problem of characterising the variability of a deposit between the known data locations.Conditional simulation can provide a number of equiprobable images of a deposit, at a finer resolution than would be economic or practical to sample, and that can be constrained by various criteria (which may be geological, statistical and geostatistical), to ensure that the images reasonably represent the deposit. These images can then be used to assess the risk involved in various practical mining decisions. Examples are provided where conditional simulation has been used for validating resource estimate parameters, optimising grade control sampling grids, and for ore block optimisation for mining grade control.

Jan 1, 1997

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004

This paper reviews the issues of mining machinery automation with special emphasis on underground applications. Automation is desirable because it offers the following advantages: ò increased safety by reducing human exposure to hazards of underground mining; ò higher productivity; and ò reduced wear of equipment. In spite of these advantages and in spite of numerous attempts over the past several decades, mining automation has been a difficult proposition, partly because no two mining operations are exactly alike and these operations are carried out in an unpredictable environment. This is the main difference between automation in factories and in mines and that is why mining automation has been lagging so far behind factory automation. Automation is possible only when the machine 'knows' its workspace. In a factory, this workspace can be 'described' to the machine because it is sufficiently controlled. In a mine, the environment undergoes continuous change and the only way the machine can 'know' its workspace is through real-time sensing.

Jan 1, 1995

By Walton M. C

A combination of flotation and smelting technologies is proposed as a cost-effective means to maximise the revenue of base metal operations. The proposed treatment route breaks the grade - recovery nexus associated with the treatment of ores exhibiting difficult mineralogy in conventional plants. Aspects of the two technologies are reviewed and typical capital and operating costs presented. A significant improvement in revenue is demonstrated in a worked example, where a copper-lead-zinc operation is examined in terms of the conventional and proposed treatment options. For the selected ore, the net smelter return per tonne of mill feed improved 57 per cent, from US$89.70 to US$141.10 with the proposed treatment option. This represents an additional US$51.4 million in annual revenue. Metallurgical operating costs increased by US$20.12 per tonne of mill feed for an incremental capital requirement of US$30.3 million for an existing operation.

Jan 1, 1992

By Gole MJ

The Goodyear nickel prospect is located 45 km southeast of Kalgoorlie (31.04¦S, 121.80¦E) near the eastern boundary of Hampton Area - East Location 45 (Figure 1). Nickel mineralisation was discovered on the Goodyear prospect in March 1996 when a reverse circulation drillhole (GYC5), initially drilled in December 1995, was deepened to meet a minimum footwall penetration requirement of 20 in that had been set for the drill program. Approximately 3 in of sulphides averaging 4.9 per cent nickel was intersected from 296 metres down-hole, this being within 2 in of the first end-of-hole. Hole GYC5 was part of an eight hole drilling program undertaken by Titan Resources in late-1995. This program was designed to test whether nickel mineralisation in the Dunlop prospect, discovered by the Western Mining Corporation - BHP Camylia Joint Venture immediately east of the East Location 45 boundary, continued across the tenement boundary. The area targeted by the initial drill program had been explored by Western Mining Corporation in the mid-1980s using extensive surface sampling and a drilling program that included 17 RAB and percussion drillholes. None of these holes intersected nickel Mineralisation.\

Jan 1, 1996

In response to requests from the iron ore mining industry, the Commonwealth Scientific and Industrial Research Organisation (CSIRO) Division of Mineral Physics has developed a number of bulk analysis techniques in which analyses are obtained directly from ore samples weighing many kilograms or from ore located on conveyor belts.Because penetrating neutron and gamma radiation is used, measurements are obtained from a large volume of ore, which ensures thal the analyses are represelllative of the bulk.Two different gamma-ray techniques have been developed to measure iron ore grade. The first is based on backscallering of 60CO gamma rays, while the second involves measurement of the annihilation radiation which arises when the ore is irradiated wilh 226Ra gamma rays. Both techniques measure the iron concentration with an accuracy (1 s) of better than 0.4% Fe.A thermal-neutron irradiation technique using a 252Cf neutron source has been developed for the simultaneous determination of iron and the aluminium impurity (expressed as AI2O3) in iron ore fines on a conveyor bell. Because the conveyor speed must not exceed about 0.05 m/s, if good accuracy for AI2O3 is required, an auxiliary analysis bell is required Lo avoid inLerference with normal ore processing. Dynamic trials have demonstrated that accuracies of 0.6% Fe and 0.1% AI2O3 can be obtained.

Jan 1, 1985

By Parsons A. E

The application of known pelletizing tech- nology was successful in the agglomeration of zinc concentrate into pellets of minus 6mm siz- ing using fine zinc calcine and sulphuric acid as binder. Subsequent roasting trials conducted in a 0.3 m diameter fluid bed reactor, showed that the pellets satisfactorily withstood hot physical abrasion during fluidization. Fines generation was low and the pellet calcine was hard, possessing excellent handling properties. Results of laboratory scale static pellet sinter- ing tests showed conclusively that the deterior- ation in sinter physical quality experienced with fine calcine was not apparent when the calcine was added to the mix in pellet form. Based on the results of small scale exper- imental work, a one tonne per hour pilot plant was constructed and operated. Several thousand tonne of pellets were produced-for fluid bed roasting in Badische Analin and Soda Fabrik (B.A.S.F.) turbulent layer (T.L.) roasters previously designed for roasting iron pyrite concentrate. Continuity of the T.L. fluid bed roasting operations was achieved when the waste heat boilers were replaced with atmospheric coolers and thus eliminated the problems of gas flow restrictions. Sinter plant trials were conducted over a period of two weeks with the addition of pellet calcine to the sinter feed. Results showed a marked improvement in sinter plant performance, and as a result of better bed permeability, increased sinter production was achieved, with- out significant deterioration in sinter quality.

Jan 1, 1974

Knowledge of the hydrogeological setting of a mine forms an integral part of a mining operation. Groundwater impacts, initially, on mine feasibility. Then, on commencement of mining, it interacts on the operational components of dewatering, water supply, tailings leachates, mine wall stability, stormwater run-off, water disposal, impact on regional environment and mine closure planning. The recording of hydrogeological information is frequently overlooked during resource and reserve definition as well as during the course of mining when prime opportunity exists for the collection and collation of this data. In recent times, the exclusion of hydrogeological data has been exacerbated by use of high air pressure drill rigs that exclude water inflow. The recording of water data has been further inhibited by the use of computer coded drill logs that do not include the site geologistÆs or drillerÆs comments on drilling problems and observations associated with groundwater intersections. Geologists now infrequently directly supervise drill rigs, but visit the rig only intermittently to evaluate drilling progress. They do not see first hand drill performance characteristics at water make zones. Drill cuttings, as drill chips and cores, are now mostly logged away from the drill site so that wet sample locations, visual water flow evidence and verbal comments from the driller are not recorded. As a result, mine geologists now do not direct adequate attention to the delineation of lithologies and structures that store and transmit water. This paper provides examples of water sighting and recording techniques applicable to a mining operation. Examples are also provided where hydrogeological conditions have been disregarded with serious impact on the progress of mining. The recording of hydrogeological data should be maintained and formatted by the site geologists into a useful database for review as and when required by specialists in hydrogeology, geotechnical and mining engineering and the environment. The information can be coded by the site geologist for inclusion into the mine database. A groundwater dataset, compiled during the progress of field investigations, will save the considerable cost of re-drilling and hole re-entry testing which would otherwise be required to provide base level hydrogeological information required for progress of mining. Apart from working mine use, a hydrogeological dataset is a necessary component for planning mining closure and mine legacy conditions.

Jan 1, 2003

Industrial and telecommunications organizations around the world are now turning to optical fibres to satisfy their growing needs for data, voice and video communications and to solve transmission problems in noisy and hazardous environments. Already, coaxial cables have been made obsolete for intermediate and long distance applications and fibres are making in-roads on other copper cable and microwave system techniques.The idea of optical fibres is not new, but techniques to manufacture the high quality cable and components required have only recently been developed. Nonetheless, the technology is now advanced, reliable and mature, and costs are plummeting with increased production and market competition.The mining industry has benefited greatly from developments in electronics and communications over the years. Optical fibres are to have a further significant impact and the time is now right for the industry to begin to exploit the many advantages of this new medium. Applications include data transmission, long distance telecommunications, measurement and control systems, surveillance, computer networks, etc.This paper briefly describes the characteristics of optical fibres, current status of the technology, applications and possibilities for future development.

Jan 1, 1984

By Edwards R

Greater efficiency of capture of minus 6 mm to fine micron size particles of free gold is achieved with the Knelson Concentrator. The development, principles of operation and recent innovations relating to this enhanced gravity concentrating device are described by the inventor, followed by a description of application and consequent economic benefits in low grade alluvial gold deposits by a large scale user of Knelson Concentrators in the Northern Territory of Australia.

Jan 1, 1990

Revised throughput rates, as a result of current mining methods and tight controls on mine dilution, have dictated a change in metallurgical philosophy at Renison Limited. Emphasis on throughput capacity increases has altered to a reduction in circuit complexity and operating costs. Extensive surveys of the gravity and cassiterite flotation circuits led to several plant modifications between August 1989 and March 1990. The coarse and fine gravity retreatment roughing tables were by-passed, the coarse gravity retreatment roughing tables were re-commissioned, the cassiterite flotation rougher capacity expanded and the gravity regrind cyclones re-configured.

Jan 1, 1991

A major tool in the search for petroleum is reflection seismic mapping. The period which has seen most of the exploration in Victoria is also one which has seen major advances in this technology, from 1963 try present day. Seismic mapping can be divided into three interlinked areas - acquisition, processing, and interpretation. In acquisition the major changes have been from an explosive energy source in 1963 to gas exploders in 1968 and airguns in 1970. The number of recording channels has increased from 24 to 192, with digital recording introduced in 1966, and floating point recording in 1976.

Jan 1, 1982

By OÆShea P. J, Dickson T. W

In April 1994 the Victorian Premier announced new State initiatives, collectively termed the Victorian Initiative for Minerals and Petroleum (VIMP), for exploration totalling $16.5 m over three years. The program, initially centred on the northwest of Victoria, the Eastern Highlands and the Otway Basin, is due for completion in June 1997 and has been designed to attract explorers to highly prospective but currently under-explored parts of the State. Major components of the program include acquisition of geophysical data (including airborne magnetics and radiometrics, gravity and seismic data), stratigraphic drilling, geological mapping and mineral resource data compilation. At the completion of the current program, 70 per cent of the State will have been covered by airborne magnetic and radiometric coverage at 400 m line spacing or better (Figure I) while 20 per cent of the State will have been covered by new geological mapping. The completion of database compilations for geochemistry, mine data and exploration licence summaries during the VIMP program is shown in Figure 2. The new airborne geophysical surveys have been flown partly under the VIMP program and partly by AGSO under the National Geoscience Mapping Accord (NGMA). Data from these surveys have been interpreted and incorporated into the geological mapping in order to enhance the quality of map products, especially in areas of Cainozoic cover. The first series 1:250 000 scale geological map coverage of Victoria was completed by the Geological Survey of Victoria (GSV) in 1977, and was based on compilation of historical geological mapping with minor field checking in most cases. The first metric 1:50 000 scale geology maps were also commenced in the 1970s, but were discontinued in the 1980s in favour of 1:100 000 scale map production. Driven by customer survey findings and with the benefit of detailed airborne geophysical data in the 1990s, the GSV reverted to 1:50 000 scale map production in 1995, with 1:10 000 scale maps made in areas of significant gold production. Geological reports still cover standard 1:100 000 scale map areas, but are now accompanied by four 1:50 000 scale maps. These new series 1:50 000 scale geological maps have been supported by comprehensive mine data and exploration licence summary databases in addition to the new geophysics, and benefit from the advances made in structural geological interpretation over the last decade. The new phase of geological mapping in Victoria, commenced under the NGMA in 1990 and accelerated under VIMP in 1994, has been focused in the central Victorian goldfields and eastern Highlands areas of the State (Figure 1). Results to-date have led to a number of major advances in the understanding of the eeoloeical evolution of Victoria.

Jan 1, 1997

By Lyman GJ

Systems for the routine on-line determination of ash content of process streams in coal preparation plants and handling systems have been in use in Australia for over four years. More recently, monitors for on-line moisture measurement have been developed to complement the ash measurement function. The technology for these systems is reviewed briefly. The development of reliable ash and moisture monitors has made the implementation of automatic systems of coal quality control practical. The emerging philosophies of automatic control in Australian preparation plants are examined with particular emphasis on systems involving dense medium circuit regulation. Related developments in flotation control and coal sorting are noted to complete this overview.

Jan 1, 1987