Search Documents

The recommissioning of the plant at Mary Kathleen involved several distinct phases. The previous plant process was modified significantly, the plant capacity was increased by the addition of new equipment and the exist- ing equipment was in most cases overhauled. This equipment was either reused in its original duty or relocated. Maintenance requirements after the plant was cmommissioned were high because of the amount of modified equipment and also because some old items of equipment were deliberately not overhauled during recommissioning. The equipment that was overhauled has operated reliably. However some new equipment has not been as satisfactory.

Jan 1, 1978

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

Australia as a leading producer of mineral sands has also occupied a leading position in many areas of research'in the processing and applications of these minerals. Research in upgrading ilmenite to produce synthetic rutile has resulted in the develop- ment of many processes, e.g,., Becher, Murso, Chlorine Technology, and ICI processes. Studies on the reducibility of ilmenites, aqueous leaching of reduced ilmenites, Fe-Ti-O system, leachability of natural and treated ilmenites in hydrochloric acid and selective chlorination of iron from ilmenites have been carried out in order to develop and improve the efficiency of the above processes. While research on the processing of zircon sand to produce high purity (99.99% ZrO2 zirconia powder and zirconium chemicals started only recently, research by CSIRO in the early 1970s led to the discovery of the phenomenon of transformation toughening in partially stabilized zirconia (PSZ) ceramics. Australia, with very significant resources of lanthanide-containing ores, pro- duces substantial quantities of monazite each year but research in processing and appli- cations of rare earths was neglected in recent years in this country. However, research to improve processes for the recovery of rare earths is now under way and studies on the production and testing of Nd-B-Fe magnets which are 1.5-2 times stronger than the strongest magnets (Sm-Co) currently available, have also commenced.' An overview of the research in the pro- cessing and applications of mineral sands during the last two decades in Australia and its implications for the industry are pre- sented in the paper.

Jan 1, 1986

By Herbst JA

During the last decade, it has been established that conventional mineral-processing control strategies based on classical control theory result in significant increases in plant throughput and operating-cost saving. The proper education and training of personnel using dynamic simulators of the principal unit operations is vital for proper design and maintenance of control systems. Severe multivariable interactions and numerous constraints on both manipulated and state variables in grinding/classifica-tion and flotation systems can be studied using time domain analysis with proper dynamic simulators. Two interactive programs are described, and the basis of each simulator and its structure are discussed. Two examples concerned with choosing, tuning, and decoupl-ing of manipulated and controlled variables for a grinding/classification circuit (DYNA-MILL II) and for a rougher flotation circuit (DYNAFLOAT II) are presented. The way in which these dynamic simulators can be used for the design of model-based control strate-gies is also outlined. A brief description of the use of these dynamic simulators for screening alternative strategies and circuit optimization is given.

Jan 1, 1985

The production of 100,000 tonnes per year of synthetic rutile from the processing of ilmenite, coal and copperas (iron sulphate) produces 200 cubic metres per hour of effluent water. A 2.0 hectare biological filter, comprising natural and man- made wetlands, has been built into the last stage of the effluent water treatment system. It is an area of shallow water (

Jan 1, 1988

By Brouwer G, Shaw J

As South African gold mines go deeper, and improved and more uniform working condi- tions are required, ever larger amounts of refrigeration are needed. At the same time new and more suitable cooling equipment is becoming available for use with new mining layouts as well as on existing shaft systems. The advent of the large diameter rotor screw compressor has meant that there is now a machine available with great flexibility in performance and construction for efficient underground use. The first installation using this type of machine is described.

Jan 1, 1988

By Goldstone A

The paper introduces a newly developed multi-function test rig for fracture grouting. This test rig has many functions and its performance is consistent. It can control and adjust accurately the opening degree of fissures and static pres- sure; it can measure automatically the quantity of grout injected; it can measure precisely pressure drop of grout in fissures; it can test the results of injection, including effective dispersed distance, anti-filtration capacity of consolidated body, mechanical strength, etc. It can inject a single or two grouts into one or several fissures at a pressure of 16 MPa. Therefore, it is an ideal test rig for fracture injection. The paper depicts all the components of the test rig, its performance and application of the results obtained from fracture grouting tests. Examples are briefly described.

Jan 1, 1988

Traditional techniques for extracting pillars in thick underground coal seams in India are reviewed. Problems encountered are principally control of roof strata and low recovery. Recently developed mechanized methods and projected newer techniques are discussed.

Jan 1, 1986

By Napier-Munn T. J, Morrison R. D, Moloney M. J, Corrans I. J

A dynamic simulator for CIP / CIL gold recovery plants has been developed at the Julius Kruttschnitt Mineral Research Centre within a collaborative, industrially - funded AMIRA project and with the participation of the Western Australian School of Mines. The simulator incorporates kinetic models for the leaching of gold from ore and its adsorption onto activated carbon, and the residence time distributions of the leach liquor, pulp solids and carbon in the circuit. Features of the simulator include the effects of gold loading distributions on both the ore and carbon on reaction rates, and the difference in residence time distribution between the leach liquor and pulp solids. The simulator allows for the estimation of kinetic model parameters from full scale applications, as well as some scale - up of parameters from laboratory batch tests. The laboratory tests were conducted at the WASM as part of the collaborative research project. The simulator can operate in both steady - state and dynamic modes, and has potential applications in design, optimisation and control of CIP / CIL plants.

Jan 1, 1991

The geochemistry of waste rock from mining operations is critical to the development of acidity-related environmental problems during mining operations, and following mine closure. Failure to recognise the potential for waste rock to produce acidic oxidation products may cause mobilisation of heavy metals into ground and surface waters, and create heavy metal levels in soils which are toxic to plants, causing the failure of revegetation programs. Although more usually associated with wet tropical environments, the potential exists for these problems to occur even in and regions such as the Eastern Goldfields region of Western Australia unless appropriate pre-planning is undertaken.Acidity-related mine waste problems can be extremely expensive to rectify, but can be avoided by waste rock characterisation, and pre-planning of waste rock deposition based on this information. Integration of knowledge of waste rock geochemistry with geotechnical engineering, and application to likely problems, is essential for the successful planning and implementation of cost-effective strategies to avoid problems occurring. Pre-planning to avoid problems is likely to be significantly less expensive in most cases than remedial actions to rectify problems after they have occurred, and in fact may involve no additional cost if it requires only rescheduling or redesign of existing or planned Activities.

Jan 1, 1993

By L E. Setiawan

The mining and milling groups at Batu Hijau are tasked with increasing SAG mill throughput by approximately ten per cent. Avenues used for this process are blasting and crushing optimisation, ore blending and predicting SAG mill throughput in relation to the geological model. This is in line with traditional æMine to MillÆ studies. At Batu Hijau, mill and mine sequencing cannot readily be configured to perform the surveys traditionally required by a æMine to MillÆ study while meeting the daily production target of 140 000 tonnes per day and processing from varying ore types in one pit. A program called BOCCOST (blasting optimisation crushing conveying optimising SAG throughput) has been implemented to capture approximately 200 variables from blasting, mining and milling operations and assign them to a common point in space in the geological model in real time. Interpretive analysis of data from BOCCOST is used to model relationships between the 200 variables to determine which and how these factors affect SAG throughput. Once these relationships are determined, the blasting, ore blending and crushing process can be optimised to generate a product that maximises mill throughput. The relationships modelled from BOCCOST are also used to generate a SAG mill throughput estimator, which can be coded into the production block model. The block model can be reconciled with the geological block model for correlation by geological domain. Once this relationship is established, SAG mill throughput domains can then be established for predicting SAG mill throughput. This SAG mill throughput estimator is then used in conjunction with revenue calculations to determine an ore cut-off, which combines these two elements to maximise metal production.

Jan 1, 2002

By L S. Barbour, M K. Meiers

Soil covers for mine waste are subject to changes in structure as a result of root development, and wet/dry or freeze/thaw cycling. The purpose of this study was to evaluate the changes in the hydraulic conductivity of three non-compacted clay covers over time. The covers are located on a sodic/saline overburden fill (30-Dump) at the Syncrude oilsands mine in Fort MacMurray, Alberta, Canada. Monitoring of these covers for temperature, matric suction, and water content by the University of Saskatchewan has been ongoing for more than three years. The three covers (D1, D2, and D3) were constructed in 1999 and are 50 cm, 35 cm, and 100 cm thick. The covers are comprised of a surface layer of reclaimed peat/mineral mix over a secondary reclaimed mineral soil (glacial till or glaciolacustrine clay), placed over a sloping shale surface. Field measurements of hydraulic conductivity within the secondary layer were obtained using a Guelph Permeameter during the 2000, 2001, and 2002 summer field seasons. Repeated measurements were made within the D1, D2, and D3 covers at depths of approximately 40 cm, 30 cm, and 60 cm, respectively. The values of hydraulic conductivity for the covers were similar to each other during each of the field study seasons. The mean hydraulic conductivity of the secondary layer increased every year: 2.5 + 10-6 cm/sec to 2.1 + 10-4 cm/sec to 4.3 + 10-4 cm/sec from 2000 to 2001 to 2002. Soil temperature data shows that one freeze/thaw cycle occurred each year at the measurement depths.

Jan 1, 2003

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

By T Clemens, D Trumm

Adopting environmentally acceptable practices in New Zealand is a crucial requirement for mineral wealth development. Recent planned expansions in the coal and gold industry have increasingly placed mining in the media spotlight. A lack of appropriate standard environmental guidelines has resulted in inconsistent responses and assessments of current and proposed mines. These inconsistencies have lead to delays in decisions on developing economic mineral deposits that may have only minor short-term impacts, and have also allowed unacceptable environmental management practices to continue elsewhere. A research collaboration between CRL Energy, Landcare Research, University of Canterbury and University of Otago aims to provide regulator groups and the mining industry with a unified approach to the requirements of the Resource Management Act 1991,the legislation that largely drives the nationÆs environmental policies and guidelines. The tangible outcome of this research program will be water quality and impact management guidelines integrated into a decision-making framework. The result of this unification will assist in the development of viable mineral deposits and minimise environmental impacts. The framework will be derived from a synthesis of three objectives. Objective 1 identifies potential water quality impact. This objective is based on a targeted geochemical study of the lithology and waterways of the West Coast and Southland regions. Objective 2 categorises the degree of impacts on the ecology of receiving aquatic ecosystems and determines the processes that drive aquatic ecosystem recovery. Objective 3 identifies best strategies to sufficiently manage impacted ecosystems, and to prevent future unacceptable impacts. Wide consultation with representatives of the mining industry and regulator groups will occur frequently during the development stages of the framework. It is anticipated that this multidisciplinary approach will provide a robust and coherent, standardised system that will assist in achieving industry and environmental targets.

Jan 1, 2004

By H Zahiri

Utilisation of the InSAR technique for monitoring of subsidence in mining areas, employing open pit and underground mining methods, has large potential due to sensitivity and safety issues associated with usage of the classical surveying techniques. InSAR can also be very competitive concerning the cost of provided results. However, there are a few issues that may significantly limit InSAR applicability for subsidence monitoring in mining areas. The altered terrain topography, involving steep slopes and deep pits, may lead to the layover of radar signal for specific satellite and pit geometry. Also, the highly dynamic character of subsidence induced by mining, especially using mass mining methods, may lead to issues such as apparent heave and ambiguous results. In this paper the authors analyse the above-mentioned issues and demonstrate how InSAR technology was applied, as a supporting system, to monitor large scale and highly dynamic subsidence for a real case study in Western Australia.

Jan 1, 2008

By Hawes GW

Until 1980 copper, lead and zinc sulphide slurries have been success- fully dewatered for rail and sea transport for many years at the Rose- bery site of North Broken Hill Holdings Ltd. utilizing conventional vacuum disc filtration systems. An upgrading and mill expansion program completed in 1981, which also permitted the introduction of ore streams changes, had resulted in difficulties dewatering copper and lead sulphide slurries to comply with transportable moisture limits. Following an extensive investigation which included both laboratory and pilot plant testing a program was commenced to replace the 2 vacuum disc filtration systems with 2 pressure filtration systems for use on copper and lead slurry dewatering and also to retain other existing vacuum disc filters as standby. An analysis of mill operations performance resulted in slurry storage tanks with a capacity equivalent to 20 hours of normal production being incorporated into the project. The pressure filters are mounted above the concentrate stock- piles. A sealed sloping floor incorporating launders is used to prevent any accidental contamination of the concentrate from pipe leakages, spillage, or from water hoses used for clean up purposes around the area. The project was completed in 1985 and operating performance has been better than that predicted from testwork. Equipment availability at 95076 together with the slurry storage capacity provided results in minimal requirement for the standby vacuum filtration system. Some typical operating results are given.

Jan 1, 1988

According to the Australian Bureau of Statistics, fatalities from road transport accidents represented an average of over 97 per cent of all transport related accidents between 1997 and 2002. With increasing traffic density, tunnels are becoming a more viable means of providing alternative travel routes to ease areas of congestion in the road transport network. However, unlike open road conditions, a fire incident in the confined space of a tunnel environment may impact upon many users that are remote from the incident location. In this context, designing for an appropriate level of safety in tunnels is therefore an important consideration for achieving consistency in the life safety measures for users of the road transport network. Unfortunately, like fire safety engineering design for buildings, there are presently no clear measures in the design processes to assess the adequacy of the design in terms of attaining the level of safety implicated in the design objectives. This is partly due to the indeterminate nature in which the design objective or the level of performance measure is stated û the intent of the objective is relatively clear but the measure of it is not. Another reason is the lack of a standardised procedure for determining the critical design variables affecting life safety. This is important to ascertain consistency in the use or adoption of the important parameters for design. This paper looks at the processes involved in the fire engineering design of road tunnels that are currently practised. A review of the design processes for fire safety in road tunnels is provided, which includes the range of fire scenarios in a tunnel environment, the traffic flow and composition, the relevant fire protection systems, the ventilation and smoke control system, the egress provisions and the benefits of incorporating fire brigade intervention. A simplified risk assessment approach is developed for a typical road tunnel to assess and evaluate the impact of a range of design parameters on life safety. Using a sensitivity technique, the important variables are then identified and means of reducing design variations associated with them are recommended. The technique may be further refined for use in the development of codes or guidelines in order to develop a suitable means of deriving more consistent design values, and hence achieve better consistency in the overall level of safety in the design.

Jan 1, 2008

In this paper presented are the criteria used when assessing the harmfulness of shocks affecting the buildings. Those criteria are based on the value of speed or accelerations of building vibrations. Presented is the scale of harmfulness of vibrations of Langefors and Kihlstrom, Bureau of Mines, and SWD contained in the Polish Norm PN-85/B-02170. The parameters of the mining shocks measured by the Lubin coal mine station were compared with the parameters calculated as per the correlations (regression curves). The average acceleration calculated from the correlations for eight measurements is only two per cent higher than the actual one. But the average frequency of vibrations calculated from the correlations for eight measurements is as much as 2.22 times lower than the actual one. In order to analyse whether that takes place in the whole range of the energy of shocks compared were the results of calculations from the correlations for various magnitudes of shocks and various distances from their epicentre with the results of the measurements. From that it follows that only for the shocks of the highest energies the lowering of the frequency of vibrations by two times causes movement from the higher zone of harmfulness to the lower one (for example from the IV to III). In the one-family houses in Lubin there were the damages that are characteristic for not only for the III but also for the IV sphere of harmfulness as per the SWD scale. That should be explained via further research and maybe it would be feasible to draw out a new correlation to determine the frequencies only for high values of energy of shocks and determine the preciseness of the acceleration and frequency correlations used presently.

Jan 1, 2003

An attempt has been made in tftis paper to review the general situation regarding the needs of the Mining and Minerals Industry for skilled and qualified personnel. Having defined the behavioural objectives of the courses of study, reference is thereafter made to the factors influencing the effective design of courses for apprentices, technicians and Technologists.

Jan 1, 1981

By L Ryan, S Halley

The use of a field spectrometer to systematically analyse drill samples from over 200 holes around the Permian-Carboniferous Ravenswood gold deposits in north-east Queensland has successfully identified both small and deposit-scale changes in the alteration mineral chemistry. Changes in chlorite composition within the tonalite host rocks are evident at the district scale, with Fe-rich chlorites seemingly more common in the vicinity of the deposits. Significant variations in white mica chemistry also occur, but mostly on the vein selvage scale, with no clear distinction between near-mine and distal compositions. The results indicate that chlorite compositional maps produced from regional field or airborne spectrometer data could potentially be used as a vector to ore in exploring for similar deposits in the area. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008