Search Documents

By Stewart W. J

The volumetric method of estimating hydrocarbon resources and recoverable reserves is and probably will remain a dominant method in petroleum engineering. The method is technically very simple, but has one main problem: how to express, measure and properly handle the variable and complex uncertainty of each estimate. The computer age brought in the Monte Carlo Simulation method which enables correct arithmetic operation using data with specified probability distribution. However, several problems are still not solved uniquely and still exist. For instance, the determination and description of the distribution of single parameters, the determination of the degree of dependency between parameters (e.g. hydrocarbon saturation-porosity), and standard probabilist- ic definition of generally used categories (e.g. proved, probable, possible). Methods for handling these problems are discussed.

Jan 1, 1979

Pongkor Gold Mines is one of seven units of production owned by PT Aneka Tambang (State owned mining company). The mine is located in the western part of Java Island, Indonesia. It is in the Bogor District and approximately 110 kilometres to the south of capital Jakarta. It is located in very steep hilly terrain intersected by many river valleys and the mine site is approximately 500 metres above mean sea level (see Figures 1 and 2 - Mine location map and picture)

Jan 1, 1997

By Large RR

Underlying the 15 million tonne, high grade Hellyer volcanogenic massive sulphide deposit of western Tasmania is an extensive, well developed, and well preserved stringer system. Pervasive alteration of the footwall mafic volcanics occurred as the hydrothermal system initiated. Mineralogical zoning exists within the footwall alteration pipe, with a central siliceous core giving way to zones of chlorite, chlorite-carbonate, sericite-chlorite, and finally sericite-quartz on the margins (stringer envelope zone). However, the alteration morphology and zonation is not symmetrical around the central siliceous core; eastward the alteration zones are steeply dipping and terminate abruptly under the massive sulphide, while westward they extend out under the ore body in a blanket fashion. Geologic evidence indicates that the pervasive alteration started with the development of sericite-quartz which was subsequently overprinted by chlorite and finally quartz-sericite as the hydrothermal system became focused towards the centre of the stringer system.

Jan 1, 1990

A review of the factors controlling stope wall behaviour such as excavation geometry, rockmass strength, induced stress, ground support, blast damage and drill drive layout is undertaken. In addition, the advantages and disadvantages of single lift stope geometries linked to vertical crater retreat are also analysed. Finally, key components of multiple lift stoping such as cut-off slots, production rings, stope undercuts and drawpoints are studied in detail.

Jan 1, 2000

By S Corbel, P J. T Donchak, W Gorczyk

The Hodgkinson Province numerical modelling project aims to develop an improved understanding of the physical conditions that lead to the localisation of goldbearing fluids within known systems and apply this understanding to the prediction of potential new sites of gold mineralisation. The project follows a series of stages from identifying the key parameters required to construct and test simulations through to reverse engineering of known deposits and ultimately applying the conditions identified in the preliminary stages to predictive simulations. Results of the modelling demonstrate strong geometric controls of the localisation of fluids during mineralisation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J Heyes, T Cooper, M Stimpfl, R Staines, J P. Pearce

Acid and Metalliferous Drainage (AMD) is one of the key risks facing the mining industry worldwide. If not properly managed and/or not identified in a timely manner, AMD has the potential to decrease environmental values for generations to come. Ore extraction generates vast volumes of mineral waste (waste rock and tailings) which are stored in perpetuity at the mine site. Some of these materials are not inert and when in contact with air and water can react, generating poor quality water and compromising operational and closure environmental objectives. Understanding the geochemical behaviour of waste rock and tailings is therefore key to identifying risks and opportunities which support effective mineral waste management strategies across the mining value chain and progress toward an environmentally sustainable future that minimises closure liabilities. To ensure AMD risk is recognised and managed uniformly across its portfolio, BHP developed a Global AMD Management Standard for implementation across all operations, including closed sites. The AMD Management Standard provides a management framework to support the consistent, simple and sustainable global management of AMD risks. This ensures mines are planned and operated to be environmentally smart and modern, geochemical risk management is not an afterthought but a key driver, and environmental sustainability is actively pursued to reduce closure liabilities. The AMD Management Framework, on which the Standard is based, was adapted from industry leading practice guidance, ensuring it applies to multiple regions. The framework also comprises sequential requirements throughout the mining life-cycle. It is an iterative framework with an adaptive management approach that is designed to incorporate new data, information and management opportunities into AMD risk assessments and mine plan revisions.

Jul 1, 2021

The Drummond Basin is a large intracratonic basin which developed in central Queensland during Late Devonian to Early Carboniferous times. It is postulated that the Drummond Basin developed as a foreland basin, to the west of a probable west dipping continental margin volcanic arc and subduction zone. The Drummond Basin sequence has been s,ibdivided into three tectono-sedirnentary cycles. Cycle I forms the base of the sequence and comprises thick sequences of intermediate to felsic volcanics and proximal volcanolithic sediments. The volcanics, particularly in the northeast of the basin, occur in separate sub-basins around what were probably isolated eruptive centres. In contrast, the rocks of Cycle 2 and Cycle 3 have been deposited during episodes of broad, basin wide subsidence. Five major igneous episodes, some of which may be co-magmatic, are recorded in the eastern Drummond Basin and environs between the Late Devonian and the Early Permian. The first and second episodes occurred during the Late Devonian to Early Carboniferous and are represented by the volcanics in Cycle 1 and Cycle 3. The third episode involves the intrusion of granitoids of Early Carboniferous age into the Drummond Basin sequence. These occur in the Ukalunda area and are related to gold mineralisation at Ukalunda and Valhalla. Episode four includes the felsic volcanics of the Bulgonunna Volcanics. This episode does not appear to he broadly auriferous but gold mineralisation does occur in possible basal Bulgonunna Volcanics at Mount Coolon. The final episode includes a suite of granitic intrusives which intrude the Bulgonunna Volcanics and which are considered to be co-magmatic with them. These intrusives do not appear to be generally associated with gold mineralisation. Gold mineralisation is widespread in the north- eastern Drummond Basin and environs. It is probable that the gold mineralisation is concentrated in epithermal cells during the Late Devonian to Early Carboniferous volcanic cycles. This style of mineralisation appears to be related to tectonic setting in modern analogues.

Jan 1, 1989

By Williams RE, Ralston DR

Acid mine drainage is a serious environmental and economic concern, resulting in regulation of the mining industry and significant water treatment costs. An interdisciplinary approach is needed to analyze the many aspects of a complex acid drainage problem. This paper describes the integrated application of techniques from the following fields to the characterization of acid drainage at a large underground lead-zinc mine: 1) hydrogeology, 2) surface stream analysis, 3) structural analysis of fracture distribution, 4) hydrochemistry, 5) geostatistics, and 6) multivariate statistics. The Bunker Hill Mine in northern Idaho, is developed in highly fractured and faulted quartzites and discharges 95 L/sec of water with an average pH of 2.8 and an average zinc concentration of 120 mg/L. Research has been conducted on all aspects of the acid water production and drainage problem. Recharge to the mine has been investigated using geophysical techniques and tracer studies. Fracture mapping and geostatistical analysis of the fracture data have been used to determine characteristics of inflow to the mine workings. Hydrograph analysis techniques have been applied to water flow data within the underground workings. Chemical sampling and analysis have been used to identify acid producing workings, and better understand mechanisms controlling acid water production. Multivariate statistical techniques have been applied to analyze the quality and flow data. Research results from the many subprojects of the Bunker Hill study reveal the importance of an interdisciplinary approach to the analysis of acid mine drainage problems.

Jan 1, 1988

Erratic, though spatially localised occurrences of gold particles are a common feature of high-nugget gold systems. In many cases, gold is present as isolated or clustered, often coarse particles. The nugget effect is a part consequence of small-scale geologically controlled enrichment, and the inclusion or exclusion of gold particles from samples. Economic zones are generally contained within discrete structurally-controlled ore shoots which are surrounded by, and may include barren to low-grade background material. Problems are often encountered where small sample types (eg drill core and channel samples) of a few kilograms mass understate in situ grade by up to a few orders of magnitude, due to their general inability to represent the true gold particle distribution. This leads to uncertainty in mineral resource estimates. This contribution presents case studies where geologically-based parameters have been collected from drill core and underground faces to support grade determination. These parameters - or proxies - are based on mineralogical and/or geochemical (eg specific elemental ratios, fluid inclusion compositions and elemental correlations) criteria. Such criteria can be correlated with different grade domains to provide an indication of true grade within a geologically-controlled context. Proxies have recently been used to support resource estimates reported in accordance with the JORC Code.

Mar 1, 2010

The reduction of titanium tetrachloride to trichloride can be achieved by employing hydrogen and electric arcs. It is possible to produce melts containing up to 50% TiCk in the eutectic mixture of LiCl/KCl by striking a D.C. arc at the surface in the presence of hydrogen and TiCl. vapour. If the electrode IS made to just penetrate the surface of the salt mixture, a hot zone results from the' high resistance contact with both lower chlorides and sintered titanium may be produced. The sintered metal forms just below the melt surface while the trichloride forms at the gaslIiquid junction.The "hotspot cathode" appears to offer a solution to the problem of producing coherent deposits as the spong'e metal can 'be continuously withdrawn in a similar manner to the "calcium process".INTRODUCTIONConsiderable interest has been shown for some years in the possible development of a cheap electrolytic process for the extraction of titanium metal, since a method using simple materials and cheap electric power would materially reduce the cost of production. Even when cheap starting materials are used, however, there exist several general difficulties in the operation of plant which both limit the speed of production and increase the cost of the product. It happens that most of the techniques so far tried produce a powder as cathodic deposit, and when this is the case the following difficulties arise:1. The whole contents of the bath must be treated with solvent in order to extract the 'metal powder which may itself tend to oxidise, and thus become contaminated.2. Fine metal powders, which often contain residual entrained salts, are less easy to consolidate by arcmelting than metal sponge.

Jan 1, 1956

The Queensland Department of Mines believes it is in the best interests of the gold mining industry to reduce and control the environmental impacts from gold mining since that is the community expectation.The Department of Mines has set as a special condition of many recently granted Mining Leases the requirement to submit a "Description of Operations" for the approval of the Minister, prior to commencing initial mining operations. In order to facilitate compliance by lessees with this condition an explanation is given of the reasons for this condition and how it is intended to achieve the objective of environmental protection.Environmental impact is operations dependent. Impact on a lease will vary quite significantly with the scale and methods employed. Before a lease can be granted and mined it is therefore necessary to have this information. The parameters of operations most critical both in terms of environment impact and economic viability are worked out and agreed with the lessee before the lease is granted. An approved description of operations which is required now, prior to the start of mining, provides the details of that agreement for the security and benefit of the lessee and the inspectors. It also provides the details of operations and environmental controls which were not required prior to the grant of the lease but are nevertheless required and necessary for compliance with the environmental standards.

Jan 1, 1986

By C Quirion

Agnico-Eagle Mines Limited, Laronde Division, operates the deepest single-lift shaft in the western hemisphere. The initial Penna hoisting plant was designed for a production rate of 1800 tonnes per day (t/d) from a 2240 m deep shaft. Exploration success, while sinking the shaft, led to a decision in 1998 to increase the production rate to 4500 t/d of ore from a loading depth of 2200 m. The new production rate was achieved by increasing the size of the rope and reducing the rope static factor from the existing 5.0 required by regulation to a static factor using the formula 25 000/(4000 + L) contained in a draft document that would eventually become SABS 0294 in South Africa. The formula permits Laronde to use a static factor as low as 4.0. The upgraded Penna hoisting system is the first hoisting plant outside of South Africa to meet the South African requirements. This paper describes the conversion of the hoisting plant to the lower rope selection factor in the year 2000 and the operating and maintenance issues experienced since then.

Jan 1, 2005

By C Mroczek, B Mitchell

Perilya Broken Hill, from its inception, has budgeted for more than 2.0 million tonnes per year from the Southern Operations. This tonnage was planned to come from in excess of 100 stopes per year in a remnant mining environment with numerous mined voids and consequent mining challenges. To mine an average of two stopes per week requires patience, flexibility and detailed knowledge to best manage the potential risks and hazards. The evolution of the Perilya Broken Hill Mine Planning Process has necessitated the establishment of a process to identify and manage these risks during the planning stage in a reliable but efficient manner. This process is to ensure that vital steps for each stope are not missed, and that each personÆs work can be tracked by other members of the team. This paper outlines the planning process from resource to stope closure.

Jan 1, 2005

By P Ormsby, T Hewitt

Ore in pillars constitutes a significant proportion of the ore reserve at PasmincoÆs Broken Hill Mine. Many of these pillars are narrow (5 -6 m) and high (16 û 35 m) vertical blocks. High-grade ore has been left between primary horizontal cut and fill stopes. These stopes were mined from the late-1960s until the early-1980s. Fill material is a variety of hydraulically stowed sand, sand-cement, and remnant timber support. Many pillar cut-throughs were made between the old stopes. In order to gain access for the current pillar recovery operations, it has been necessary to develop pillar drill drives through, and adjacent to, the hydraulic filled stopes. Whilst long hole recovery of vertical pillars is not new, some notable successes using innovative ideas have been achieved during 1997. These innovations include:The use of steel mesh reinforcing in shotcrete when mining through, or adjacent to, hydraulic fill. Construction of steel sets to support vent rises and haulage ways encountered in the cut-throughs. The use of ground movement monitoring equipment. Survey lasers with chain droppers and convergence monitors were installed in the 18 Pillar to detect any movement of the pillar block and decrease risk to personnel. The development of a three-dimensional computer model of primary stoping, using Vulcan software, to assist in the design of pillars. Maximisation of recovery using different drilling and firing practices.

Jan 1, 1998

By H Waterer, L Zheng, T Kalinowski

The Hunter Valley Coal Chain (HVCC) consists of mining companies, rail operators, rail track owners and terminal operators, together forming the worldÆs largest coal exporting facility. In 2008, the throughput of HVCC was about 92 million tonnes, or more than ten per cent of the worldÆs total trade in coal for that year. The coal export operation generates around $15 billion in annual export income for Australia. As demand has increased significantly in recent years, and is expected to increase further in the future, efficient supply chain management is crucial. The Hunter Valley Coal Chain Coordinator Limited (HVCCC) was founded to enable integrated planning and coordination of the interests of all parties, thus improving the efficiency of the system as a whole. One of the many planning challenges faced by the HVCCC is that of annual maintenance planning. Different supply chain elements, such as trains, railway track, terminal equipment and load points, must undergo regular preventive and corrective maintenance, leading to significant reductions in system capacity (up to 15 per cent). However good alignment of the maintenance tasks can reduce their impact, and the HVCCC undertakes an annual process to ensure the impact of maintenance on the supply chain capacity is as small as possible. This is achieved in an iterative negotiation process between HVCCC and individual service providers. In the past, maintenance schedule optimisation was largely manual, which for the more than 1000 tasks involved is quite labour-intensive.In this paper the authors describe an approach developed at the University of Newcastle in partnership with the HVCCC to automate this schedule optimisation process. We will discuss our experience in applying exact (mixed integer programming) and heuristic techniques from mathematics and computer science to address the problem. This work is anticipated to lead to new decision-support tools for the HVCCCÆs capacity planning team.

Sep 26, 2011

By D Stow, M Edmondson

Lemington coal mine is operating in an environmentally sensitive area in the Hunter Valley, NSW, Australia. Late in 1999 the southern pit was developed using a series of box cut blasts. After the initial development the area would have been free dug due to the soft, well-jointed nature of the deposit. However, it was decided to trial drill and blast to determine if shovel productivity could be improved to enable an overall mining cost reduction. The initial trial blast results were less than satisfactory with both environmental issues occurring and the desired shovel productivity not being achieved. An audit of the blasts indicated that wet ground and the presence of soft clay inter-bedded with harder rock caused the poor blast results. Also, water-affected explosive product combined with explosive energy loss into soft ground led to flat spots and tight digging in the hard band areas, resulting in the lower dig rates. Lemington Mine and Orica Explosives developed a plan to match the rock with the appropriate explosive type and energy. This resulted in a number of blasts over a six-month period using a new non fuming explosive product, æNovaliteÆ. The results have been excellent with the environmental issues being totally resolved and dig rates improved, enabling reductions in mining costs. This has allowed the mine to continue with their exemplary record of environmental management whilst achieving operational efficiencies.

Jan 1, 2001

By S Bouzalakos, W Timms, H Malli

Combining ultramafic mine tailings and acidic mine drainage via mineral carbonation to sequester carbon dioxide, presents an opportunity to minimise waste on mine sites. Low pH mine water with trace element concentrations can be effectively treated by high magnesium mine tailings, a useful source of finely ground reactive matrix. By using milled tailings for mineral carbonation, there are negligible energy requirements for communition of ore rocks to reduce particle size. This study aimed to assess the technical applicability of reacting ultramafic tailings and acidic mine water through mineral carbonation technology in the mining industry. Dissolution has been identified as the rate limiting stage in mineral carbonation; hence the study focused on identifying optimal dissolution conditions. Ultramafic tailings (particle size <100 µm) derived from serpentinite ore, were reacted with a typical mine water that was synthesised in the laboratory. Through variances in the solid to liquid ratios and temperature of dissolution, a maximum five per cent magnesium dissolution efficiency was reached at 50 g/L and 100°C. The acidic mine water was neutralised (from pH <2 to pH ~6) and iron, copper and zinc ion concentrations reduced significantly during the formation of solid precipitates. Carbonation was undertaken by injecting carbon dioxide into the magnesium-rich solution to form stable carbonates. The experimental work demonstrated proof of concept; however, dissolution efficiency and carbon dioxide sequestration was low, indicating that further research would be required before larger scale implementation.CITATION:Malli, H, Bouzalakos, S and Timms, W, 2015. Ultramafic mine tailings to treat acidic mine water and lock away carbon through mineral carbonation, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 133–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D S. Stewart, K W. Keskimaki

In 1999, the Henderson Mine commissioned the Henderson 2000 project - a new truck haulage level, a new underground crusher and a 24 kilometre conveyor system to replace a 23-year old rail haulage system. Henderson has been able to continuously improve in almost all aspects of its rubber-tired mining. The rail haulage system represented one of the last barriers to continuous improvement to the overall plant performance. Many of the lessons learned in other areas of the mine were utilised to design the truck level. This paper chronicles the benchmarking, equipment selection and design of the level. Areas covered will include haulage trucks, level layout, ore chute design, traffic control, road design and crusher layout.

Jan 1, 2000

The purpose of this paper is to review recent approaches by regulators, employers and employees and their associations to the introduction of flexible employment practices and the management of fatigue related risk. More importantly, it will focus on developments in our law either through legislative change and cases which have dictated trends. The paper particularly considers the limitations imposed by occupational health and safety legislation to resist or limit the move to flexible workplace practices on the basis that such practices are unsafe.

Jan 1, 2003

By Guo H

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack Orientation.

Jan 1, 1992