Search Documents

By Cox SJD, Kramadibrata S

One of the major causes of accidents and loss of production in underground mines is falls of ground.As mines go deeper, higher stresses are encountered and strain energy stored in the rocks is more likely to be released dynamically. This results in bumping in the rock mass around a stope or development face. Such noises and increasingly difficult ground conditions are obviously a warning of more serious problems ahead. The activity is collectively referred to as rock bursting.In Australia the mining of metalliferous deposits is taking place at increasing depths at Mt Isa, Broken Hill and the Eastern Goldfields and ground control problems with rock bursts has already been experienced at all three sites.

Jan 1, 1990

By Takasaki Y, Ohzeki S, Hotta H

TO measure high temperature properties of blast furnace burdens ( the change of gas permeability accompanied by contraction, soft- ening and melting ) which govern the gas flow and its distribution, a series of experiments were carried out under simulated blast furnace conditions, using sinter, acid pellets and self -fluxing pellets. 1) The high temperature properties are affected by the ore's reducibility ( up to 1000 -1200¦C ), and the composition, and volume of gangue before reduction. Generally, the burde- ns with high basicity ( Ca0/Si02 ), high reduc- ibility and low volume of gangue have good high temperature properties. Good high temperature properties are : a high temperature at which the gas permeability rapidly decreases, a high melting point and a low maximum pressure drop. 2) Using acid pellets, slow-down of red- uction rate occurs around 1000¦C because the pellet forms a dense metallic shell, while its slag core, resulting from a FeO, Si02 and A1203 reaction, has a lower melting point. 3) The addition of MgO sources improves high temperature properties both of sinter and Pellets.

Jan 1, 1980

By McCarthy P. L

A distinctive feature of the goldfields of Victoria was the extrac- tion of gold from deep leads, that is the buried river beds of Vic- toria's ancient rivers and streams. It is estimated that about 265,000 kg of gold was produced from Victoria's deep lead mines which comprises about 11.5% of Victoria's total production of gold (Bowen, 1974). The significance of deep lead mining for Victoria, however, went far beyond its economic contribution to Victoria. If Profes- sor Blainey is correct it was the frustrations of mining gold from deep alluvial leads in Ballarat during 1854 which precipitated the Eureka Stockade (Blainey, 1963, 46-52). This event resulted in the implementation of a fair mining administration and was an emphatic statement of the rise of democratic movements in Australia. Much of the technology and skill for mining deep leads had to be developed locally because at that time no other major gold- field elsewhere in Australia or the world had gold deposits with comparable problems. Deep lead mining in Victoria was there- fore largely a home grown industry and the equipment for that industry was often designed and produced in Victoria.

Jan 1, 1988

By James CH

For drainage sediment to be used as a successful sampling medium in reconnaissance geochemical surveys, the length of any dispersion train from a typical target must be great enough for it to be detected by a widely spaced sampling pattern, and must also be homogeneous enough to avoid it being missed by the unfortunate selection of a random low value sample. Elements which occur in stream sediments in the form of discrete heavy minerals present two special problems in this regard. Since the element is concentrated into a few particles, the medium is extremely heterogeneous, which makes representative sampling impossible unless very large samples are taken, while the high specific gravity of such grains leads to their being concentrated in traps along the stream bed. Several ways of overcoming these difficulties have been suggested. Among these the "schlich" test, in which heavy material obtained by panning is taken for analysis is among the most popular. However, the results of the present study indicate that while this method improves the nature of the patterns obtained, they are still far from satisfactory. Alternative methods of sample preparation, including the taking of light material for analysis, appear to provide better answers to the problem. In the area studied this approach eliminated most of the "noise" associated with the data obtained by other methods, as well as giving an extended dispersion pattern.

Jan 1, 1986

The mining of mineral sands in coastal aquifers is often constrained by other land use conflicts and inappropriate controls imposed through a lack of understanding of environmental interactions and processes. The recent experience with the Tea Gardens mining operation illustrates how increasing our knowledge and understanding leads to more effective management of environmental problems. As well as a source of heavy minerals, the Tea Gardens sand bed serves as a town water supply source. From past experience it was believed that mining could cause undesirable increases in dissolved iron concentrations in the aquifer, but the reasons and mechanisms for this phenomenon were not clear. A water monitoring program was therefore designed for the mining operation which was aimed at protecting the water supply borefield from any detremental effects. After one year the results of the monitoring program were assessed in the light of new knowledge and understanding of iron hydrochemistry. It was found that the existing program was not achieving some of its major aims, and was therefore modified to a more effective and cost efficient program.

Jan 1, 1988

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

The moisture content of clean coal contributes significantly to the product's transportation costs, handleability characteristics and/or energy value. A major contributor to the total moisture is the ever increasing proportion of fine coal in

Jan 1, 1994

The tankhouse of the electrolytic zinc plant at Nordenham is operating with a very high operating efficiency of 99 per cent. This has been achieved not only by strict control of the quality of the zinc sulphate cell feed solution but also by all the improvements in housekeeping in the tankhouse developed during the past years: aluminium cathode specification, cathode stripping cycle, edge strips, copper contacts, anode isolators, cell cleaning, fittings and washing devices. During 1987 to 1992 the casting department was completely remodelled in order to improve the quality of the zinc products, the safety of the operations and the flexibility. The remodelling includes the enlargement of the area for the casting shop, the storage buildings and the five casting lines on the same ground level. New lines for alloying products and for SHG25 kg zinc ingots have been constructed. The line for galvanising products has new equipment in some parts and the other lines have been modified.

Jan 1, 1993

Traditional vat leaching has been done on a batch basis, which involves loading the vats, leaching, drainage, washing, draining again, and unloading. As a result of these many steps and the attendent cost of labor, vat leaching is generally not an economic proposition. Also, like heap leaching, there is a tendency for channeling to occur within the bed, whether the leach solution flow is by percolation upwards or downwards. No doubt experimenters over the decades have been enticed by the idea of fluidization induced by upward flow through the ore bed. If the bed could be fluidized, then a continuous flow of material could be set up, dispensing with the high cost of loading and unloading the vat. A quick calculation of solution flow requirements, however, soon reveals that the volume of constant liquid movement necessary to sustain fluidization is prohibitive from a power and cost standpoint. The premise of the Mackie Vat Leaching Jig (MVLT) concept was that the large volume of liquid flow required for fluidization could be achieved instantaneously, and that during this small element of time, the solids would flow under the influence of the hydraulic gradient in the vat. If this procedure could be repeated in a cyclic manner, then a steady-state condition could be set up. Experiments in the laboratory demonstrated that solids flow could be achieved in this manner.

Jan 1, 1991

By Nevolina VG, Zakharova IB

The results of a study on the flotation of baddeleyite and associate minerals are presented, together with effective flotation reagents. Detailed microcrystallomorphological analysis of the benefication products were made to find out the features of distribution of different baddeleyite generations between froth and chamber products. To reveal the dynamics of interaction of technological properties of minerals with their morphology and constitution, a method of onthogenetic analysis was used. It is well known that the difference between technological properties of the particles of the same mineral depend greatly on its genesis, but also the relation is direct - by means of constitution (habit). Thus, flotation behaviour of minerals depends on morphology microinclusions, distribution of impurities, dislocations and physical properties of individual particles. The microrelief of baddeleyite grains and crystals from froth and chamber products was studied with an electron scanning microscope. Chemical composition was determined by means of laser, microprobe and chemical analyses. The difference between baddeleyite generations, their distribution in benefication products, and the effects of grain sizes, number of inclusions and chemical compositions were valuated. Conclusions on baddeleyite flotation properties were made. Mineralogical study on eudialite grains from rough ore and eudialite concentrate was carried out. The interrelation between eudialite and associate minerals and negative effect of aegirine on technological properties of eudialite were revealed as well.

Jan 1, 1993

By Vynne J. F

Drill monitors for blasthole and exploration drills have been available to the mining industry since the 1970s. The early monitors were pen strip chart recorders which were developed for the oil drilling industry and adapted to mining. They recorded drilling parameters such as depth, pull-down pressure, torque, RPM, and bailing air pressure. While these recorders could generate a large volume of paper, the amount of useful data was minimal. The data was not summarised and required an engineer to interrupt the chart traces. Being a mechanical recorder, the devices were also susceptible to frequent failures.

Jan 1, 1993

Physical model testing at Bergbauforschung is done in two rigs, a roadway rig and a longwall rig. The loading of such models, in scale relation to the con- ditions in the collieries provides valuable guidance to the probability and nature of failures, and thus to support requirements, in structural, roofbolts and self- auvancing supports. The success of such modelling when related to subsequent underground designs put to use suggests that such methods of investigation could be extended to pillar extraction problems also.

Jan 1, 1974

By Thirumalai K, Peluso R. G

The United States has more than 45 billion tons of economic coal reserves in seams above 10 feet thick and current underground production from thick seams represent less than three per cent of the total production. A tripling of underground production from thick seams is necessary within the next 10 years to meet U.S. coal production demands. An analysis of underground accident and production data is presented in the paper. A study of accident and injury distribution in different coal seam heights in the eastern and western part of the United States in seams ranging in thicknesses from 5 to 15 feet indicates that the seam thicknesses do not produce adverse impact on underground injury incidence. Accidents associated with roof falls and haulage account for about 70 per cent of underground mining injuries.

Jan 1, 1976

By E Kasai, D Maruoka, Y Konno, T Murakami

The iron ore sintering process produces approximately three per cent of carbon dioxide emission in Japan because a large amount of coke breeze is used as the main agglomeration agent. Therefore, its suppression has been required. A promising method is to replace the coke breeze with biomass char and iron-bearing materials. In this study, the effect of the utilisation of metallic iron with coke or palm kernel shell char (PKS char) as an agglomeration agent on its oxidation behaviour was examined by a series of experiments using a sintering simulator. The use of PKS char leads to a larger decrease in the pressure drop difference of the sintering bed compared to the case using coke. Furthermore, the oxidation rate of metallic iron was larger in the case using PKS char together than that using coke. It was considered that the oxidation of metallic iron was promoted because the bed-temperature increased at a faster rate and achieved a higher temperature.

Nov 8, 2021

By S Amor, A Beasley

This paper provides an example of how industry can respond to the implementation of new regulatory approaches to mining risk, health and safety by adopting a robust, practical, software-based approach to the management of risk accountabilities in terms of competence, experience and suitability for obligations and responsibilities, as required in Queensland Coal Mining operations due to the introduction of Recognised Standard 22 (‘RS22’; Resources Safety and Health Queensland, 2021). Based on the authors’ experience from working with several Qld mine operations, it offers a snapshot of the experiences, approaches and reservations faced collectively by industry as a result of the introduction of RS22. Several challenges exist within the detail of RS22, leading to varied interpretations, implementation strategies and overall compliance between mine sites. Arguably the single biggest challenge identified has been how to find a balance between compliance and practicality – considering cost, operational interruption, available pathways for delivery of competence, ongoing compliance and value adding to the business operations and people. Software-based solutions are increasingly being relied upon to address the introduction of new regulatory approaches and the significant administrative load placed on mining operation Site Senior Executives (‘SSE’) due to RS22 means this case is no different. This is further complicated given the continuous, ongoing changes with the site management structure witnessed by the authors across each of the mining operations as a result of continuous changes to personnel, the site risk profile and an overall mining industry uncertainty of how to respond to RS22. The stringent reporting/notification requirements under legislation compounds this further. The approach put forward by the authors is a well-considered rationale and approach to the application of training and skilling; and equally how to ‘future proof’ the coordination of site training needs around changes to the Management Structure, the Risk Register, skilling processes and succession planning. A brief investigation of other legislative frameworks concluded this approach would likely meet or exceed expectations of jurisdictions across Australia and overseas, making this a highly flexible approach for establishing a competent Management Structure to provide safe systems of work.

Apr 16, 2024

By Sharpin PC

The countercurrent gas-solid-heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temp-erature distributions through the drier have been calculated. Although the calculations rest on several simplifying assump-tions, to be corrected as the experimental work develops, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating con-ditions on the rate of drying of the briquettes which-controls the 2 strength of the char produced. The analysis shows why a limitation was reached in the improvement of char-strength in the pilot plant in 1961 and a prediction is made of ' a way ' in ' which the limitation could be overcome.

Jan 1, 1963

Nordberg has conducted extensive research, during 1982-85, on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Nordberg's engineers have developed advanced design and testing techniques that ensure efficient and reliable crusher designs. Combination of this knowledge has resulted in a design of the MPI000 (1000 hp) crusher which fits on the existing 7ft Symons foundation and yet is capable of producing twice the ton- nage of the 7ft. In this paper the development of the MP1000 crusher and its performance compared to the 7ft heavy duty and super heavy duty crushers will be discussed. Also, substantial cost savings resulting from the application of such a high performance machine will be presented.

Jan 1, 1988

By Treglown N

In any mining operation the curtailment of rising operating costs is of prime concern to management.One area of activity where costs are often disguised is that of longhole secondary breakage.This paper outlines sane operational techniques that have been considered and tested, resulting in improved fragmentation fran longhole stope blasts at New Broken Hill Consolidated Limited mine, Broken Hill, NSW.

Jan 1, 1985

By Beer G

The recent re-emergence of an Integral Pressure Stripping system which operates with both cell and column in closed circuit at elevated temperature and pressure, requires no cyanide in the eluate solution and has greatly reduced carbon reactivation requirements in seen as a progressive step in this area. Several of these re-configured IPS systems have been placed in service in Australia and overseas in the last three years, with the first of the new generation units constructed and commissioned by Como Engineers Pty. Ltd. at Mt. Fisher in the East Murchison of W.A. in September 1987. This plant was relocated to a new ore body at Darlot W.A. in February 1989. Use is made of a data base of raw plant performance figures from both Mr. Fisher and Darlot and its performance compared with other operating plants. Initial commissioning difficulties of the Mt. Fisher prototype and dis- cussed together with the modifications and operational procedures required to overcome these problems. Stripping times of less than 6 hours at 145 degrees have been achieved with barren carbon values less than l O ppm from loaded carbon values above 3000 ppm and with cell pass efficiencies reaching 90 per cent.

Jan 1, 1991

LITHOPROBE is a national, collaborative research grogram with the general objective of understanding the teotectonic evolution of the North American continent through multidisciplinary lithospheric studies in carefully selected areas of Canada. Six transect areas are investigating Precambrian evolution, although only in two of these is the research well evolved. The Archean Kapuskasing Structural Zone in Ontario is confirmed as an upthrust slice of upper to mid crust exposed at the surface. The Late Proterozoic Keweenawan mid-continent rift is shown to be the deepest known rift on Earth and the Grenville collisional zone of Ontario and Quebec involves crustal scale imbrication and ramping of deeply buried rocks to the surface. Two transect areas are investigating Phanerozoic evolution. In the Newfoundland Appalachians the geologically defined tectonostratigraphic domains do not coincide with lower crustal blocks defined by seismic reflection data. The Southern Cordillera Transect in western Canada is examining the nature, timing and dynamics of the assembly of the Cordillera, and particularly the role of accreted terranes. Work in the eastern and central segments has extended the known western limit of the North American craton at least IOO km westward and crustal-scale ramps associated with metamorphic core complexes have been identified.

Jan 1, 1990