Search Documents

Queensland hosts vast deposits of brown and black coal, significant accumulations ranging in age from Permian to early Tertiary. The great diversity of coal resources in the State to some extent reflects the proximity of Queensland to plate-marginal tectonic processes through much of the Phanerozoic eon. Coal is contained within sedimentary basin fills of four fundamental types; 1. extensional, 2. foreland, 3. strike-slip, and 4. intracratonic. Thick (10 m+) though laterally restricted coal bodies are characteristic of extensional and strike-slip basins, whereas coals of more modest thickness but much greater lateral extent are typical of foreland and intracratonic basins.

Jan 1, 1991

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By Watson D. F

P S B Stewart has rightly pointed to a possible obscurity in our paper on drilling patterns, viz. in comparing the improvement of a triangular drilling pattern over a square one, we used percentage improvements without always making clear their base. We hope, however, that other readers, like Stewart, have been able to understand the particular meaning from the context.Although different methods of estimation of an ore deposit will have different local bias (Philip and Watson, 1985), the critical relationship affecting the reliability of estimation of an unsampled location is the scale of local variation of the variable being estimated in comparison with the density and isotropy of sampling. This relationship overrides all other considerations.

Jan 1, 1985

The changing characteristics of raw materials has highlighted the limitations that conventional vibrating screens have in the handling of fine wet sticky materials. These' limitations have led to the development of a totally new concept of screening, the Rotating Probability Screen. In order to illustrate the practical benefits to be gained by the extraction of fine materials ahead of subse quent processes particularly in the coal industry, the experiences gained in Ro-Pro installations in America, Australia, Europe and Britain are drawn upon.

Jan 1, 1984

By J Masliyah, Z Xu

The largest oil sand deposit in the world is located in Alberta, Canada, with a total proven reserve of 2.5 trillion barrels of oil. The water based extraction process is currently being used in commercial operations to recover bitumen by flotation from oil sand ores. A recognised challenge in bitumen extraction is the reduced bitumen recovery when processing ores containing high fines content or æweatheredÆ oil sand ores, collectively known as poor processing ores. Inspired by demonstrated success of using kerosene as collectors in coal flotation, an innovative idea of using oily bubbles (air bubbles coated with a thin layer of oil or solvent) was tested to improve bitumen flotation recovery from poor processing ores. In this study, dynamic contact angle of air bubbles or oily bubbles on bitumen and induction time of bitumen-oily bubble attachment in water were measured to justify the use of oily bubbles in bitumen recovery from poor processing ores. The type of oil or solvents, including kerosene, toluene and naphtha, used in generating oily bubbles showed a marginal effect on the contact angle values, similar to the values measured with air bubbles. However, the spreading of an air bubble was found to be much slower than that of oily bubbles on a bitumen surface. The induction time for oily bubble-bitumen attachment was found to be much shorter than that for corresponding air bubble-bitumen attachment in the process water from poor processing ores. The reduced induction time for kerosene-coated air bubble-bitumen attachment correlates well with the improved bitumen recovery from poor processing ores using kerosene-coated oily bubble flotation technology.

Jan 1, 2005

By B J. Wilde

Evaluating the resources and reserves in a mineral deposit requires many interdependent subjective decisions. The decision of stationarity is arguably the most important. This decision includes: the choice of domains that subset the entire deposit, modelling the boundaries of each domain, and understanding and considering the nature of the contacts between domains. Reasonable choices are made in consideration of the geological context, the available data, the goals of the study and the available resources for the study. This paper reviews aspects of the decision of stationarity in modern resource assessment with a focus on quantifying uncertainty and using numerical/statistical tools to help the geomodeller. The use of volume/distance functions to quantify uncertainty in domain limits is particularly important and is presented in detail. The use of contact plots provides help with the continuity of grades across domain boundaries. Realisations are not assembled as a branching combinatorial of all possibilities, but as a set of realisations that provide a measure of uncertainty. This paper amounts to a definition of stationarity for modern resource assessment.

Sep 26, 2011

By Burford B. D, Johnson N. W, Rohner P

Under design philosophy, the Hilton concentrator produced lead, zinc and LGM (lead plus zinc) concentrates. The LGM (Iow grade middling) concentrate was produced by combining coarse middling streams from the lead and zinc circuits, regrinding and subsequent flotation. Mineralogical examination of the zinc circuit middling stream prior to regrinding suggested that production of zinc concentrate from the zinc circuit middling stream should be possible by rearranging existing plant equipment. Laboratory testing of samples of plant products, however, showed that regrinding combined wi th the usual reagent suite was nO1 sufficient to produce a zinc concentrate of the required specifications.Examination of the process water highlighted a problem with dissolved salts in the circuit water, which was solved by in-circuit precipitation of the dissolved ions with soda ash. Implementation of the procedure in the concentrator effectively transferred to the zinc concentrate all sphalerite previously recovered to the LGM concentrate.

Jan 1, 1994

By G W. Scott, R C. Johnson

Hypogene alteration zones have been described as a precursor to high-grade haematite deposits in Australia, Brazil and elsewhere. This alteration is described as being below or distal and is typically magnetite-carbonate-silicates reflecting Mg - Fe metasomatism. This paper describes, without genetic implication, the mineral zonation and possible structural control on mineralogic variation within the Tilden Mine, a concentrating grade haematite deposit in Michigan, USA. In contrast to the high-grade deposits, these variations are not peripheral to the orebodies but are the ore. The deposit occurs within the Negaunee Iron Formation, along the southern margin of the Paleoproterozoic Marquette Range Supergroup basin. The regional structure is a fault-bounded west plunging syncline within the crustal scale Great Lakes Tectonic Zone, which forms the boundary between Archean granite-greenstone and gneissic terranes. Local structure consists of second-order anticlines and synclines with variable northwest and southwest plunges. The interaction of sedimentation and diagenesis within growth fault controlled basins, along with a possible metamorphic and/or hydrothermal overprint has resulted in a complex series of ore types. For modelling purposes, the deposit is divided into geologic domains based on both lithology and metallurgical response in the laboratory and in the plant. Mineralogic variation is recognised within individual mineral grains; at blast pattern (10 - 15 m) and development drill hole (100 m) scales.

Jan 1, 2007

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

By Bensley C. N

In June 1995, BHP announced that it would build a Hot Briquetted Iron (HBI) plant and associated beneficiation, materials handling and infrastructure facilities at Port Hedland, Western Australia. This plant, the first direct reduction plant in Australia, will convert beneficiated iron ore fines into metallic iron for briquetting into HBI. The reduction plant will be based on the FINMET fluid bed technology jointly developed by Fior de Venezuela and Voest-Alpine Industrienlagenbau. Electric Arc Furnace steelmakers in the Asia Pacific region will be the principal customers for the product. This paper presents an overview of the facilities to be constructed by the project as well as discussing some particular technology and design engineering issues associated with the project.

Jan 1, 1996

By Polthier K

A short discussion of the salient aspects of a dispersed flow model in relation to the gas flow in blast furnaces is given. The use of the theory in assessing vessel performance is mentioned. Tracer results of a blast furnace (688 m3) from three furnace levels and different radial positions are analysed and results presented as D/ud values. The significance of the shapes of experimental tracer curves are included and comparison is made with results obtained on other furnaces.

Jan 1, 1975

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

Sampling and sample preparation systems at the Hamersley Iron Pty. Limited port of Dampier, W.A., were developed for two separate objectives. 1. The need for rapid determination of physical properties. On stream size analysis enables lump ore and pellet- ized ore physical properties to be monitored and controlled whilst shiploading is in progress. As a control procedure this facility allows optimum shiploading rates con sistent with physical quality control. 2. The need for accurate chemical analysis. Chemical analysis on ship- loading forms the final link in overall quality control procedures encompassing the operation of mining, railway and port blending. Thus maintenance of specification products with minimum variation in chemical characteristics is ensured.

Jan 1, 1976

By Haines P. W, Sweet I. P, Rawlings D. J, Page R. W, Plumb K. A

Current regional geoscientific studies across the McArthur Basin as part of the National Geoscience Mapping Accord by the Northern Territory Geological Survey and Australian Geological Survey Organisation have provided a significant amount of new data which has enabled revision of the stratigraphic and chronologic framework of the basin. This paper provides an overview of these results, with particular emphasis on new results from Arnhem Land.

Jan 1, 1994

The Honeymoon Well nickel sulphide deposits are located in the Agnew-Wiluna greenstone belt, about 45 km south of Wiluna. Both disseminated and massive sulphide nickel deposits are hosted by komatiitic rocks within the deformed and metamorphosed Honeymoon Well ultramafic complex. Fresh ultramafic bedrock is covered by up to 50 m of highly conductive transported material which greatly hampers both exploration and understanding of the bedrock geology. In the early-1970s, mineralisation was discovered by diamond drilling geochemical anomalies defined by wide-spaced percussion drilling over ultramafics that had been outlined by ground magnetics. Subsequent drilling has defined a resource of 158 Mt at 0.71 per cent nickel (based on 0.4 per cent nickel cut-off, 300 m below surface, December 1995) in four deposits. Over the life of the project a wide range of geophysical techniques have been used including airborne and ground magnetics, time domain clectromagnetics (EM), induced polarisation (IP)/resistivity, gravity and downhole techniques including EM, IP and physical property Measurements.

Jan 1, 1996

Cyanide-extractable gold is far more meaningful in the definition of ore, and control of extraction, than fire- assayable or aqua regia digestible gold. The use of cyanide- extractable gold addresses the significant problems of over- as well as under-assaying by fire and aqua regia digests. The problems of conventional control or diagnostic cyanidation extractions: lengthy extraction, and masking by pregrobbing in cyanidation extractions for assay purposes; are surmounted with a novel activator - Leach WELL. Full extraction of liberated gold, insignificantly affected by preg-robbers, can now be achieved within 30 minutes. This can assist in reducing common gold losses presently often hidden by inappropriate mine call factors, and/or high grade cut values. This paper includes a discussion of fundamental mechanisms of cyanidation, preg- and assay-robbing, which underlie the phenomena Involved.

Jan 1, 1992

Backfil ling of excavated Sub Level Open Stopes has been underway since March 1989 and as at December 1992 some 1 100 000 cubic metres of Cemented Aggregate Fill have been placed. During these three years significant developments in fill quantities, types and cost have taken place.Operational improvements have reduced the quantity of Cement Aggregate Fill by 40 per cent. These results have been achieved by:ò rescheduling stopes,ò designing smaller primary stope, and ò use of uncemented rockfill.Unit cost for Cement Aggregate Fill have fallen in the order of 50 per cent through:improving fill hole reli ability,simplified barricade construction procedures, reducing the cement content,ò substituting dune sand for deslimed mill tailings, ò improved maintenance at the Backfill plant, and ò renegotiated site freight agreement.This paper will review the historical developments of backfill use at Olympic Dam.

Jan 1, 1993

By Barber S

The Golden Cross Mine is located within the Waitekauri Valley near the southern end of the Coromandel Ranges, eight kilometres north-west of Waihi, North Island, New Zealand. The mine is owned and operated in a joint venture by Coeur Gold NZ Ltd (80 per cent) and Viking Mining Ltd (20 per cent). The underground mine produces gold and silver from low sulphidation epithermal quartz veins which developed in the shallow parts of a meteoric water dominated system during the Upper Miocene (7.36 - 6.67 Ma). The Empire Vein System is hosted within a dilational structural environment which developed at the lithological contact between acid intrusives, rhyolitic-dacitic tuffs and reworked pyroclastics, and undifferentiated andesites. The formation of the Empire Vein System was controlled by the rheological properties of the host rocks and variable displacement along a series of normal, right lateral, easterly-dipping faults. These faults represent sub-parallel zones of master shearing within a Riedel shear model. Underground mining extracts ore from the steeply dipping hangingwall and the complex footwall veins of the Empire Vein System. Initially sills are driven along the hangingwall vein on ten to fifteen metre sublevel intervals. In the footwall zones where significant mineralisation adjacent to the hangingwall sill drives has been identified, a series of cross-cuts and footwall drives (sub-parallel to the hangingwall sill) are also developed. Where continuity of mineralisation and ground conditions permit a combination of post pillar flatbacking and AVOCA longhole benching methods are used. Detailed underground mapping of lithology, quartz veining and major structures provides the information for designing ground support and footwall pillars, planning mine development and ore extraction sequencing. Sectional interpretation displays the vertical extent of faults, fractures and the vein system. The mining methods used underground at the mine have evolved through a thorough understanding of the structural complexity and the systematic geological mapping of the Empire Vein System.

Jan 1, 1997