Search Documents

By B K. Da, S A. Balaji, G P. Roy, T K. Dutta

The raw material handling complex at the Durgapur steel plant provides iron ore, crushed coke and flux to two sinter plants. Either some facilities were not envisaged or not properly designed before the project stage which caused problems during operation of the plant. The absence of an in situ roll turning facility, used to increase maintenance activities for disassembly, transportation of rolls to central machine shop and assembly of rolls, led to decreased crusher availability and increased activities for the maintenance crew. The provision of a smaller vibro feeder/screen in place of a suitable sized screen caused jamming of the screen deck, adversely affecting screening efficiency and the crushing index of crushed coke. Some design modifications and developmental work was undertaken, such as the development and installation of an in situ roll turning facility in the existing limited space, achieving low feed (0.1 - 0.2 mm/rev), lower cutting speed of 30 - 40 m/minute for 350 BHN hard roll, which was also a difficult engineering challenge to bring within the tolerable limit of vibration. This was successfully achieved. Modifications to the screen deck, introduction of differential speed crushing and modification to the vibro screen and vibro feeder for uniform distribution of feed have been incorporated. These innovative design modifications to the in situ roll turning have led to a drastic decrease in maintenance activities and an improvement in the crushing index. Modifications to the screen have resulted in the elimination of jamming and improved screening. Modifications to the vibro screen before the primary crushers and to the vibro feeder before the secondary crushers have prevented excessive wear in the central portion of rolls, ultimately leading to increased roll life. Incorporation of differential speed crushing has resulted in an increased crushing index and decreased generation of micro fines. All the above modifications have led to distinct improvements in equipment availability, increased roll life and a decrease in maintenance activities and improvement in crushed coke granulametry, ultimately resulting in improved productivity and quality of iron ore agglomeration at the sinter plant. The innovative design modifications mentioned above are discussed in detail in this paper.

Jan 1, 2005

By A H. Bagherieh, S Mesroghli, H Jorjani, S Chehreh Chelgani

The rare earth elements (REEs) assay and recovery in leaching processes is being determined using expensive analytical methods, ICP-AES, and ICP-MS. This paper presents a neural network model to predict the effects of operational variables on the lanthanum, cerium, yttrium, neodymium recovery in the leaching of apatite concentrate. The effects of leaching times: ten to 40 min, pulp densities: 30 to 50 per cent, acid concentrations: 20 to 60 per cent and agitation rates: 100 to 200 rpm were investigated and optimised on REEs recovery in laboratory at a leaching temperature of 60¦C. The obtained data, on the laboratory optimisation process were used for training and testing of a neural network. A feed-forward artificial neural network with 4-5-5-1 arrangement, was capable of estimating the REEs leaching recovery. Neural network predicted values were in good agreement with the experimental results. The correlations of R = 1 in training stages, and R =  0.971, 0.952, 0.985 and 0.98 in testing stages were results for Ce, Nd, La and Y recovery predictions respectively and that theses values are considerably acceptable. It was shown that the proposed neural network model accurately reproduces all the effects of operation variables, and can be used in the simulation of a REEs leaching plant.

Jan 1, 2008

A new approach to resource estimation at the exploration stage is emerging, based on the application of simple software techniques. The techniques combine the power of interactive graphics with proven database, analysis and estimation tools. With effective use of these tools the geologist now has maximum chance of deriving a reliable structural and grade model from the limited exploration data. Unlike cutoff-based polygonal methods, the resultant geological model can immediately be used to evaluate any economic scenario.These modelling techniques are embodied in MINEX-3D, an Australian software system. With the emergence of the 386-based PC and high resolution (VGA or better) graphics, MINEX-3D makes the power of this new 'desktop geological modelling' accessible to most exploration geologists.

Jan 1, 1990

By V S. Mutton, M J. Shearer

"The current economic challenges faced by the mining industry led to a review of options for reducing the cost of ventilation control devices (VCDs). The VCDs at the Mount Isa Mines site operated by Glencore in Queensland typically experienced significant damage on the operating levels and required expensive replacements. Ventilation controls can become damaged by the effects of stope firings. This paper discusses the nature of blast wave effects, giving consideration to distance from the firing and changes in mine geometry. The time taken to adjust the airflow on the operating levels with the current VCDs resulted in the loss of productivity opportunities. The mine site engaged an equipment supplier to collaborate on the development of a high-strength regulator to control the required airflows within its underground workings.The strengthened regulator proved to be cost-effective and provided additional benefits, including ease of use, simplicity of installation and speed of change in the control of available ventilating airflow. An added advantage of the re-engineered regulator compared to contemporary VCDs is its flexibility, which includes the ability to easily move mobile equipment into different ventilation districts where required without the need to remove the VCD from its location. This paper describes both the innovation and environmental sustainability approaches followed when developing the new regulator for its implementation at the site.CITATION:Shearer, M J and Mutton, V S, 2015. Advanced ventilation control – an analysis of innovation and environmental sustainability, in Proceedings The Australian Mine Ventilation Conference, pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Larsen D. F

Minor iron formation related base metal sulphide mineralization occurs in granulite facies metamorphic rocks of the early Proterozoic Willyama Complex. Rock sequences hosting three iron formation related Cu, Zn, Pb prospects from the Thackaringa Group (Suite 3) are described. A caparison of host rock sequences, style of mineralization and facies of iron formations suggests major differences in terms of the overall depositional environment. However, significant similarities are present with respect to the nature and distribution of iron formation facies and the occurrence of chlorite 'alteration' zones in close proximity to mineralization in all cases. The chlorite within these zones occurs in a number of diverse forms in a range of rock types. A comparison of the prospects shows that there is no evidence to indicate that the chlorite in the zones is a retrograde alteration product of former higher grade prograde mineralogies - the chlorite appears to have survived granulite facies metamorphism. The mode of occurence of the chlorite in the 'alteration' zones together with the fact that the association quartz + chlorite + magnetite + pyrite + base metals is cx rmn to all areas suggests that the chlorite is specifically related to the processes which deposited the stratiform iron formations and related sulphides. It is considered that the chlorite precursor was a prenetanorphic alteration product or chemical sediment closely related to submarine hot spring activity which was also the source for chemical sediment precursors of the iron formations, associated lode rocks and Sulphides.

Jan 1, 1983

By Keyte SG

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.1mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80% and mass yields of less than 1% can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

Controlled Source Audio Magnetotelluric (CSAMT) surveys were carried out by Glass Earth (New Zealand) Limited (Glass Earth) in 2006 - 2007 to investigate epithermal gold targets in the central North Island of New Zealand. The surveys were conducted using a Zonge GDP 32 8-channels receiver and a Zonge XMT 32 transmitter powered by a 16 KW generator. The electric field dipole was maintained at 20 m length (five dipoles per 100 m spread) and the frequency ranged from 4 KHz to 4 Hz. Only scalar (TM mode) signals were recorded, using one magnetic coil per spread. The transmitter bipoles were 1 - 4 km in length and located about 5 to 10 km from each survey area.   Sixteen individual target areas were surveyed by June 2007. The CSAMT survey lines (100 - 400 m spacing) were determined mainly on results from previous ultra-detailed airborne magnetic and gravity surveys conducted by Glass Earth in 2005. The data from each CSAMT line was carefully examined to remove any spurious signals and processed using Zonge SCS2D software, which can produce smooth 2D resistivity inversions of the field data. The results were presented as resistivity sections and maps to help the identification of exploratory drilling targets, mainly from the existence of subsurface high resistivity zones (resistors) that can be interpreted as caused by silicification associated with epithermal mineralization.   An example of processing and interpretation of the CSAMT data is presented in this paper on results from Glass EarthÆs Tahunaatara target, where CSAMT surveys have identified zones of epithermal mineralization confirmed by exploratory drilling.

Jan 1, 2007

By M McGrory, A Rodolfo, J Paredes, L E. Manguba, K A Villaspir, G Webb, R Setiagani, H Cardenas

"OceanaGold’s Didipio operation has been in operation for three years. Integral to the flow sheet design is a flash flotation circuit treating a portion of cyclone underflow, consisting of an Outotec SK-500 flash rougher and an Outotec TC10 flash cleaner and a SB-2500 falcon treating flash rougher concentrate to recover fine free gold.Flash copper recovery has been holding steady at 60 per cent, while flash gold recovery at 50 per cent. Gold recovery from the gravity circuit is 22 per cent, bringing the overall flash plus gravity gold recovery to 72 per cent.Operation of the flash rougher is mainly by pulp level control. Control of copper grade in the flash cleaner is mainly controlled by air inflow and flash cleaner pulp level control drives copper recovery. Gold recovery around the circuit is mainly driven by gold head grade.SB-2500 concentrate is scalped with a 250 micron screen with the coarse fraction reporting to a SB-250 falcon, concentrate of which combines with the screen fine fraction to a Gemini table.Citation:Cardenas, H, McGrory, M, Webb, G, Paredes, J, Setiagani, R, Villaspir, K A, Manguba, L E and Rodolfo, A, 2016. Didipio Flash Flotation and Gravity Recovery Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 123–126 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Burgess JM

Research on gas distribution in the iron- making blast furnace has been conducted in three separate areas. Firstly, experimental work has been conducted to determine the important parameters which dictate the pressure losses in homogeneous and heterogen- eous packed beds. Secondly, a theoretical analysis of gas flow through the furnace softening-melting zone has been undertaken to determine the effect of the shape of the zone on the distribution of gas flow towards the furnace walls. Thirdly, a theoretical programme has been undertaken to develop methods for the prediction of furnace soften- ing-melting zone shape from furnace tempera- ture and gas composition measurements.

Jan 1, 1980

By Wooltorton B

Highwall failures in surface coal mines in Queensland occur as circular slips through weak and weathered material, or as bilinear slides on sub-horizontal surfaces and steeply dipping joints. Weak horizontal planes occur in the Permian-Tertiary unconformity or on bedding surfaces within the Permian Coal Measures. Sub-vertical movements occur along rock joints and tension cracks induced by stress relaxation after excavation. Blasting also introduces new fractures and causes movement along existing rock discontinuities. Critical factors for stability include the dip direction of potential failure surfaces, shear strength of the rocks, damage due to blasting prior to highwall excavation, groundwater conditions, the type and performance of clays on shear surfaces, and pit geometry.

Jan 1, 1981

Rajor intrusion-related Cu and Au dep- osits along the Cordilleran-type central Andean margin and in the western Pacific island arcs constitute a series of discrete, linear belts which correspond to limited (414 m.y.) metall- ogenic epochs. The most important metallogenic belts, all of Cenozoic age, are inferred to have been generated during relatively shallow subduction of oceanic lithosphere beneath con- vergent margins. Geological and isotopic evid- ence suggests that magmatic rocks and associated Cu and Au mineralization were derived from asthenospheric mantle sources, which were enriched in a variety of elements (metals, alkalis, S) by dehydration of subducting oceanic crust. Where exceptionally rapid, low-angle 3ubduction took place beneath very thick (>50 km) continental crust, as in the central Andean Altiplano in the Miocene and southwestern North America during the Laramide, ore-related magmas underwent wholesale crustal contamination. However, the associated Cu-Au mineralization is the same as that developed in primitive island- arc crust. In particular, the by-product Au and So contents of porphyry Cu deposits are inde- pendent of crustal thickness and the degree of crustal contamination as determined isotopic- Ally.

Jan 1, 1987

By P Nichols, C te Kloot, A Harrison

Ernest Henry mine (EHM) is a sub-level caving operation located in north-west Queensland, Australia. Located below a previously mined open pit, the underground operation ramped up production to 6.8Mt/a in 2017. The EHM ore body dips at 45 degrees to the South and therefore requires each level to “step out” from the level above as seen in Figure 1. Within this step out zone it is important to both maximise recovery and allow for efficient operation of the underground workings production to bring the level up to full production as quickly as possible. Throughout the step out design process, a combination of further defining the ore boundary, using lessons learnt from production performance on upper levels and the introduction of design improvements, has reduced the production ramp-up time, decreased costs and increased recovery for a single level at EHM. CITATION: Nichols, P, te Kloot, C and Harrison, A, 2018. Case study – Ernest Henry Mine: designing step out zones in an inclined sub-level cave, in Proceedings Complex Orebodies Conference 2018, pp 53–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By D Cliff, B Belle

Trigger action response plans (TARPs) are inherent to managing multiple hazards such as high gas content with multiple coal seams, high spontaneous combustion propensity, heat and ventilation. TARPs aim to provide assurance and guidance when the situation deviates from the original plan or there is a change in conditions that could be hazardous. Over the years, learnings from various incidents have continuously required coal operations to revisit the TARP trigger values that were based on historical data or guidance values from the industry. In most cases, the background to the basis of TARP statistical data (ie average, maximum, hourly or daily for the monitoring or sampling location) is unknown. The introduction of real-time monitoring devices to monitor gases and airflows has provided greater understanding of the hazard scenarios and their controls. This paper analyses the carbon monoxide data from operating longwall mines and compares these with the historical trigger values to understand the changes and identify improvement opportunities while setting trigger levels in the TARPs. As an example of setting trigger values, those used during the sealing of a panel are explored in terms of setting values based upon the sampling location and the level of risk. It is envisaged that the learnings shared herein will further enhance the understanding and management of multiple hazards in Australian coalmines.CITATION:Belle, B and Cliff, D, 2015. Improved trigger action response plan development based upon mine-specific data, in Proceedings The Australian Mine Ventilation Conference, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977

By de Bruin J H

A method new to Australia was used for sinking a vertical shaft at Broken Hill in the development of Pasminco Southern Operations No 5 Ventilation Shaft. The 6 m diameter shaft of 820 m depth was planned with a construction method which allowed access for ground support as sinking proceeded by mechanical excavation.The vertical shaft boring machine, known as the V-Mole, was originally developed in West Germany. The machine operates in a manner similar to a full face TBM but vertically and the cuttings drop down a previously constructed raise. The raise is subject to stringent tolerance on verticality and must remain stable for the duration of reaming.

Jan 1, 1993

By G Gopinath, R Balachander, H S. Venkatesh

This paper describes in detail the controlled blasting adopted and the measurements undertaken for the successful excavation of large twin tunnels under a shallow cover for a six-lane highway project in India. The tunnels are D-shaped, each 15 m in diameter, and the cover between the tunnels and the existing railway track was about 14 m. These twin tunnel tubes were characterised by two separate three-lane carriageways for each direction of traffic, and were planned with about 25 m of reinforced cement concrete (RCC) portals at the entrance and exit of the tunnels. The major challenge of the project was the blasting of tunnels in rock below an operating railway line. As the tunnels approached the area below the railway line, the ground vibrations were monitored vertically above the blasting faces and on the railway track sleepers. Vibration intensities between those generated from tunnel blasting and those from the movement of the trains were compared, and it was found that the vibrations from blasting were lower than those from the moving trains. Though the permissible level of ground vibration based on the Indian Standard (IS) code happens to be 70 mm/s, the maximum charge per delay was calculated restricting this limit to 50 mm/s. This ensured that the vibrations in the vicinity of the railway tracks never exceeded the prescribed limit of 70 mm/s. The surface ground settlement before and after the blasts were also measured using an optical levelling instrument, which confirmed that there was no significant impact on the surface movements due to blasting. Extensometer readings inside the tunnels showed that there was no deformation in the tunnel. These twin tunnels are now operational and are providing faster connectivity with safety.CITATION:Gopinath, G, Venkatesh, H S and Balachander, R, 2015. Controlled blasting for twin tunnels with a shallow cover under an operating railway line, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G W. Scott, H M. Lukey

The Lake Superior Region has been a producer of iron ore for over 150 years. Early mining operations concentrated on direct shipping ores, which are the result of post-depositional upgrading principally by deep weathering. As direct shipping ore reserves became depleted, the focus changed to the production of iron ore pellets from taconite. The post-depositional processes responsible for upgrading taconite are regional metamorphism, contact metamorphism and hydrothermal processes (Clout and Simonson, 2005). While these processes are important in iron ore genesis they can also contribute to liberation problems and in some instances reduced pellet quality (Han, 2004). Low-grade metamorphic mineral assemblages can negatively impact liberation and pellet quality. Low-grade iron formation may contain a suite of carbonate minerals including ankerite, dolomite, kutnohorite, siderite and magnesiosiderite. Variation in the distribution and composition of siderite and magnesiosiderite makes controlling the MgO content of pellets difficult. Carbonate minerals also require calcination in the pellet induration process, which requires additional heat to be added to the system, slowing down the induration process and reducing throughput. Prediction of carbonate mineralogy and carbonate mineral chemistry is an important goal of ore characterisation for pelletising properties. Contact metamorphism causes changes in mineralogy and grain size (Klein, 1973; Gunderson and Schwartz, 1962). Increasing the grain size of magnetite should improve its liberation characteristics. However, plant grinding targets may not allow the coarse-grained, more easily liberating magnetite ores to increase throughput and can actually result in decreased throughput due to recirculation. While magnetite and martite ores are well understood (Lukey, Johnson and Scott, 2007) late open-space filling microplaty haematite ores are not. These ores, while composed of similar minerals, have a unique genesis that results in fine grain size and complex textures that present liberation challenges and often make interpreting laboratory metallurgical test results more difficult.

Jan 1, 2007

By Brinkmann J. R

In the narrow stopes of South African gold mines, rockbreaking is carried out by drilling and blasting with safety fuse and igniter cord being used as the initiation system. The fuse/gniter cord system is used primarily because of its low cost, however several limitations of this method include: inaccurate delay time, unreliable firing, inflexible application to varied configurations, and the absence of dynamic interaction between holes. Alternative initiation systems that incorporate millisecond timing are being developed to overcome the limitations of fuse(tgniter cord systems. Current investigations by the Stoping Technology Division of the Chamber of Mines Research Organization (COMRO) into the effects of millisecond initiation are being conducted at a deep test site. Experimental blasts using various millisecond delays and the independent firing of holes with fuse/igniter cord are being studied in order to quantify the influence of delay time on the blasting process and to identify the best methods of applying millisecond initiation systems. The effect of design variables such as delay time, hole firing pattern, stemming, and panel layout are discussed. Blast results including throw distance and direction, muckpile profile and rock cleaning times are used in the discussion of different combinations of blasting variables.

Jan 1, 1990

DURING the four years, 1922, 1923, 1924, and 1925, China produced the following quantities of non-ferrous metals and ores: Antimony Products - 67,869 (long) tons. The production for 1925 was 20,869 tons, of which 80% was regulus, 14% crude,and 6% oxide.Arsenic (White) - 4200 tons. The production for 1925 was 1200 tons, but only 90 tons were exported, some 25% of which to Hong-Kong, France, and U.S.A. each, and the rest in small lots to other countries. Domestic consumption was 1110 tons, and thelocal price for "cake" was around £47 per ton on 1925 exchange.Arsenic Ore (Realgar) - 1400 tons.Lead Ore (Galena) - 44,853 tons. The production for 1925 was 10,853 tons, of which 16%, produced in Korea, went to Japan, and 84% produced in Hunan, went to Europe.Manganese Ore (Pyrolusite) - 142,567 tons. The production for 1925 was 42,567 tons, of which 94.3% went to Japan.Tin Ingot - 33,480 tons. In 1925 the exports to Hong-Kong were 8880 tons of usual rough tin of 94% to 96%. Most of this was refined to No. I Chinese quality of 99.3% and exported to U.S.A. and Europe, owing to the good price ruling.Sulphur - 12,000 tons. Sulphur is included in this list in order to explain how its production led to the discovery of some other ores.Wolfram - 19,668 tons. The production in 1925 was 5868 tons, most of which came from the Quee Mee mountain district in South Kiangsi, from the detrital deposits. Civil disturbances prevented the usual output from Hunan border.Zinc Ore (Blende) - 134,190 tons. Exports for 1925 were 34,190 tons of low-grade ore, averaging 30% zinc, 14% lead, and 7% silver...

Jan 1, 1927