Search Documents

By D Wimpenny

Underground infrastructure is often a critical component of transportation and utility schemes. It is characterised by long design lives with limited access for inspection and maintenance. The exposure environment can be difficult to assess since it will often vary substantially between different locations in the same facility and with time during construction and in service. In addition, the specific demands placed upon underground infrastructure are not well covered by the exposure classes and other guidance given within current codes of practice. When problems occur they can be difficult to rectify and involve significant disruption.Given these substantial risks the prudent designer may adopt a systematic ‘durability planning’ approach which:· defines the environment and principal deterioration mechanisms for the various elements and construction materials,· predicts the design life for alternative durability enhancement options, and· recommends associated measures to be adopted during construction and in service.This paper describes the development of durability planning within Halcrow, giving examples of its use from its first implementation on tunnels under the Suez Canal in 1993 to recent projects in the Middle East and Australia. It seeks to demystify the process, identify shortcomings and speculate on its future development within the civil and mining sectors.

Mar 8, 2011

By L Snyman, S Webster and J Samosir

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant, which produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment and recover the ore.The E48 extraction level is located approximately 581 m below surface and consists of ten extraction drives and 214 drawpoints. Several stress measurements carried out at various levels in both E26 and E48 indicated a low underground regional stress environment and a low to moderate stress state in the E48 orebody. The E48 block used a post undercut strategy that was initiated in 2009, with production commencing in September 2010 and cave-through to the surface occurring approximately four months later in January 2011. Changes to the cut-off grade and fixed prices meant that Northparkes was able to develop an additional two drives to the north of the existing cave and one additional drive to the south. Modelling of the cavability of the additional drives indicated that the cave would not readily propagate to sufficient height of draw to mobilise the ore and tended to arch over to the existing cave shape. Based on modelling and a desire to reduce the risk of the project, preconditioning was adopted. Along with the requirement of safely hydrofracturing an active cave, a measure of the success of the preconditioning was desired. Few block cave operations have developed extension drives adjacent to existing caves.This paper summarises the lessons learnt from the development of this extension project, with a specific focus on ground control and monitoring.CITATION:Snyman, L, Webster, S and Samosir, J, 2016. E48 cave extension at Northparkes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By V Matousek, A Sellgren, R Visintainer, G McCall

A 4-component model for settling slurry pipe flow has been previously described by Wilson et al (2006) and Sellgren et al (2014) to predict pipeline friction loss (hydraulic pressure gradient) over a range of slurry compositions: from fine to coarse particle size, narrow to broad particle size distribution, and low to high solids concentration. The method applies a weighted average of established pipeline models for various settling slurry flow regimes, according to the volume fraction of solids falling within the applicable size range for each model. Further development of the model was undertaken by Visintainer et al (2017a, 2017b), based on a comprehensive set of laboratory tests in 203 mm (8 inch) and 103 mm (4 inch) pipelines, and it was also adapted to the modelling of slurry pump performance derates. However, this work was all performed with solids having a specific gravity near 2.65, as is typical for many mineral processing and dredging applications. The goal of the present work is to test the applicability of these models for settling slurries having a higher solids specific gravity, as may often be seen in the mineral processing of iron ore deposits. To that end, a test program was carried out in a 103 mm (4 inch) pipe loop using various compositions of an iron ore product having a solids specific gravity of 4.75 and containing both coarse and fine solids. By screening and flushing operations, a range of particle size distributions were created having different proportions of the coarse and fine elements. In all, 19 tests were performed with d50 particle sizes ranging from 50 μm to 3.2 mm and delivered solids concentrations from 10 per cent to 43 per cent by volume. Particle size distributions varied from very narrow to very broad, with d85/d50 ratios ranging from 1.75 to 26. Pipeline pressure gradient and pump performance data were collected and used to test the applicability of the previously developed 4- component models and to propose improvements to the models for the handling of high-density solids.

Nov 8, 2021

By D Reid

Run-out analyses of tailings storage facilities are typically undertaken using methods based on rheological theory. These are reasonable techniques to model the behaviour of tailings that, through significant run-out and possibly mixing with supernatant water, are generally acting in a fluidised manner. Such modelling often follows on from two-dimensional continuum analysis models where, if failure is predicted, grid failure often occurs when deformations begin to increase. This results in a disconnect between the prediction of failure and the modelling of the potential extent of the failure.Recently, rezoning methods have been incorporated into commercially available two-dimensional soil mechanics deformation codes. Rezoning techniques enable large deformations to be modelled within a two-dimensional continuum analysis framework; however, while promising, the use of such tools is not yet widespread, and a consensus is yet to develop on how they should be applied to tailings dam run-out modelling.This paper uses FLAC rezoning techniques to model the flow behaviour of two historic tailings dam failures. The purpose of these analyses is to critically assess the performance of rezoning against some available historic failures. The required data to undertake such an analysis is outlined, along with the inherent limitations and assumptions required. Parametric analyses are outlined to address some of these issues. In general, the analyses undertaken underestimated the flow distance observed in the historic failures by varying degrees; however, in some instances, the analysis reasonably reproduced the qualitative shape of the initial failure zone. A variety of potential reasons for the discrepancy between historical observations and the models undertaken are provided.CITATION:Reid, D, 2015. The use of rezoning techniques to model historic tailings failures, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Laros T, Schoenbrunn F

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to he successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings inipoundineni design, underflow pumping, and control system.

Jan 1, 1998

By J I Stewart

The Copper Canyon deposits, occur in proximity to the regionally distinctive formational boundary between the Staveley Formation and Marimo Shale. The mineralisation here is associated with breccias, veins, and alteration zones near the base of the Marimo Shale unit and in the underlying evaporitic dolomite-dololutite dominant Staveley Formation. The Marimo Shale unit, in its basal 60 metres, is highly carbonaceous and hosts ubiquitous but minor diagenetic (?) copper-pyrite, and on occasion, extensive albite-microcline alteration centres, pyritic (cobaltiferous)-quartz veins, and microcline-quartz_+plagioclase veins or veinlet arrays. The most significant mineralisation, such as at the Greenrnount prospect, consists of a shallowly dipping package of alteration zones overprinted by multiple generations of pink-orange microcline-quartz-chalcopyrite-pyrite-(arsenopyrite) and albite-calcite- phlogopite veins. Accessory mineralogies in most of these mineralisation styles consist of tourmaline, monazite, rutile, and apatite. Chalcopyrite (and secondary chalcocite) and gold are associated with each generation of alteration but are best developed in the later stages of veining. In the underlying Staveley Formation, which is a conformable transition between the Corella Formation limestones and the Marimo Shale, chalcopyrite (cobaltiferous)-pyrite mineralisation occurs as disseminations in pre- and syntectonic breccias, and with disaggregated silica pseudomorphs (after thinly bedded evaporitic sulphate beds) and associated dolomitised limestone-calcilutite. Although this mineralisation may be partly diagenetic in origin the 200 in thick evaporitic packages are also host to a locally widespread (2 to 4 km long and 200 to >500 metres wide) and pervasive 'redrock' styled microcline-dolomite¦hematite alteration. Within this gross alteration package there also seems to be a consistent association with narrow (10 to 100 metres wide), linear (stratabound) semi-massive magnetite-hematite-microcline and quartz-chalcedony replacement zones. Like much of the nearby Corella Formation the Staveley Formation, under the Marimo Shale, has undergone dissolution, paleo-solution karsting (breccias) and tectonic brecciation such that the precursor lithological details have been progressively obliterated. The post-diagenetic to post-tectonic fluid pathway development and metasomatic alteration history of this important lithostructural package of rocks has been traced from preliminary studies only. The ability to do so is largely due to the absence of significant regional and contact metamorphic overprinting, and the local preservation of precursor sediment profiles. It is proposed that both the base of the Marimo Shale and parts of the underlying evaporitic-limestone-dololutite have acted as conformable fluid pathways for hydrothermal and (perhaps) diagenetically derived, Cu-Au-(¦Co ¦As) K-Na-Ti-REE bearing, fluids and brines.

Jan 1, 1994

New technology is a significant factor in the present upsurge in world, and Australian, gold extraction and production. The main technologies in current use for gold production are described, referring to overseas developments. Areas where existing techniques have shortcomings or new methods are needed are pinpointed and discussed. Much research work on gold metallurgy is under way round the world, and many new developments have potential. Many of the current research activities round the world are covering unusual and striking areas, with surprising results starting to come through. Some of the "blue sky" techniques reportedly under investigation are identified, together with consideration of when changes in technology are of value. The consequences of new technology for personnel involved in gold plant operations will be raised, including the new education now required.

Jan 1, 1986

By M Field

Kimberlite pipes, as opposed to dykes, sill and secondary deposits, are the primary target for diamond exploration companies because they have simple geometries and can contain large volumes of potentially diamond-bearing ore. Once discovered, important decisions have to be made regarding the sampling of these geological entities to establish the total volume of ore present, and to define the internal geology, which can be complex in nature and controls the distribution of diamond grade. It is essential that as part of this process the uncertainty in constructed geological models are assessed. In this paper the Orapa AK1 kimberlite pipe in Botswana is used as a case study to explore a potential methodology for defining this uncertainty. The uncertainty of the rock volumes of different types can be characterised by a geostatistical approach. Geostatistical simulations, based upon a plausible representation of the geological bodies, provide different possible images of the orebody that can be considered as different realities. By testing different borehole layouts and drilling the orebody virtually on the computer, many different, but equi-probable realisations of the pipes can be produced. It is then possible to estimate the rocksÆ volumes and compare them with the actual ones. A statistical analysis of the relationship between estimation error and the number of boreholes can then be used to optimise the next sampling campaign. The rock volumes are obtained from a two-step simulation process. Firstly, the pipe geometry is simulated by means of introducing variations around the geological block model, by an original method called centre point simulation (CPS), which has been developed for this purpose. Secondly, the internal geology is then simulated within the pipe. The methodology for simulating the internal geological zones has to be adapted to the level of information and to the geological structure itself. The upper portion at Orapa AK1 is filled with sedimentary crater facies. Here plurigaussian simulation techniques can be applied that are adapted to the simulation of sedimentary facies. The central zones of the pipe are typically subvertically-oriented massive volcaniclastic deposits and breccias and the lower regions comprise a complex root zone. CPS is appropriate for these zones.

Jan 1, 2006

Historically the insurance industryÆs involvement in any project has been relatively late in the process. Often it was a case of the last item to be ticked off the checklist has been to ensure that the insurance is in place. However, in more recent times insurers have imposed more restrictions on the cover they are prepared to provide, which has in some cases necessitated a change in the contracting structure to accommodate the insurance policy(ies). In addition, changing contractual practices have changed the allocation of risk between the various parties involved. This calls for a more proactive approach to the design and implementation of an insurance program for both the construction and operational phases of any resource project. This paper explores how a risk managed approach to the design and implementation of an insurance program for a resource project can align itself with current management approaches to project development. From the authorsÆ experience, this approach is best adopted early on in the project (often in conjunction with the bankable feasibility study) and follows AZ/NZS4360 to objectively examine and compare a wide range of risk exposures of the project in a time-effective manner across the following areas: personnel; environment; general management; compliance û legislation, systems, protocols; asset management; change management; financial impacts to the organisation; products/services; service delivery; and technology. Having identified and then analysed the risk exposures according to common consequence and likelihood ratings the next step is to develop a risk map of all considered exposures. The true value of this approach lies in the development and implementation of a risk treatment plan for identified exposures where the exposure is unacceptable. The plans will lead to the optimal solution to the appropriate risk prevention, risk mitigation and risk transfer options available. This paper also examines other benefits to the project that may arise from adopting a risk managed approach in addition to the ability to design an insurance program which recognises the exposures and the ability of the organisation (and other project parties) to retain risk.

Jan 1, 2007

By Cocks T

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By B P. Wrench, M J. Gowan, P J. Chapman

Embankment dams constructed mainly of sand or non-plastic fine soils are susceptible to liquefaction, particularly in high-rainfall, high-seismicity environments where there is sufficient water to saturate the materials and sufficient energy from an earthquake to cause liquefaction. This paper shows the process adopted to review the stability of an existing cross-valley, centreline-raised cyclone tailings sand embankment dam.The study showed that two-dimensional stability analyses did not sufficiently capture the potential for instability, overestimating the depth of the critical failure surface. Instead, three-dimensional modelling was required to provide a reasonable representation. Post-liquefaction stability analyses carried out using the three-dimensional model indicated an adequate factor of safety (FoS). The FoS under seismic conditions was still considered to be a concern based on pseudostatic analyses (but noting the limitations of the analysis method).Earthquake-induced settlements were estimated using an empirical approach based on case history records (Swaisgood, 2003). The post-earthquake event settlement was estimated to be in the order of 600 mm, which is considered to be acceptable for the embankment, taking account of the proposed long-term freeboard of more than 8 m under operating conditions and 2 m under the probable maximum flood condition.CITATION:Chapman, P J, Wrench, B P and Gowan, M J, 2015. Review of static and seismic stability of a cross-valley sand tailings embankment in a high-rainfall, high-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M Castello, P Bouchard, M Sabsabi, A Blouin, B Nguegang Kamwa, M Constantin, K Fytas, M Laflamme, K Rifai, F Vidal

Canada’s Quebec province operates 26 metal mines, 19 of which are producing gold and generating over C$1.8 billion (US$1.3 billion) annually. In all those mines, numerous samples of rock are collected and analysed daily in laboratories in order to determine their gold content. However, laboratory results are generally available within 48 hours of sampling (depending on the number of samples received by the laboratory and the priority of the results), thus potentially slowing down mining activities. In an attempt to find a solution for delayed laboratory results, Laval University, in partnership with the National Research Council Canada (NRC), the National Institute for Scientific Research (INRS) and four mining companies (Agnico Eagle, Canadian Malartic, Hecla Québec and Iamgold) have launched the Laser-Induced Breakdown Spectroscopy (LIBS) project for in situ real-time mining sample analysis. This work aims to minimise the amount of LIBS point sampling necessary to be representative of a full scan of the analysed area. Eight sampling patterns are investigated. A statistical analysis of the data was performed by varying the pattern steps. Results show that two of the patterns, 1 and 5 (single diagonal crossing the stratification of the samples with opposite slopes) minimise the amount of point sampling while remaining representative. The most successful results are obtained from steps which are greater than 6. In terms of the type of material, pattern 5 and steps 9 are better for core sampling, while pattern 1 and steps 8 are better for rock sampling. The geological explanation for these results is the heterogeneous distribution of gold in the sample which seems to be more homogeneous in the rocks than in the core sample due to the small rock size. In terms of the mineralisation, pattern 5 is better for mixed sulfides and quartz veins, and steps 8 and 9 are better for quartz veins.CITATION:Nguegang Kamwa, B, Rifai, K, Laflamme, M, Constantin, M, Castello, M, Vidal, F, Bouchard, P, Fytas, K, Blouin, A and Sabsabi, M, 2017. Sampling strategy by statistical analyses of LIBS data in the context of a portable gold analyser, in Proceedings Tenth International Mining Geology Conference 2017, pp 221–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By F van de Venter, J Monama, T Kale

For a multitude of years fine iron ore, -1 mm, across the world has been deposited as discard material in tailings facilities. This contributes to environmental problems, decreases plant yield and increases the cost of processing. Fine iron ore recovery processes are often deemed unfeasible or uneconomical, due to the complexity of the reclamation thereof in comparison with high-grade ores. However, recent advances in the recovery of fine iron ore using the Optima Classifier® has shown great promise. The Optima Classifier® is a new hindered settling separator that makes use of an upward current of water for density separation. It’s unique design combines three different separating zones for increased efficiency and recovery. In this study the potential of the Optima Classifier® to produce a +63 per cent Fe concentrate from -1 mm feed material was evaluated from a standalone and process perspective. It was found that a +63 per cent Fe product can be produced from a single stage, using the Optima Classifier®. Fine iron ore feed with an average head grade of 50 per cent Fe was upgraded to average concentrate grades of 63.2 per cent Fe. Displaying upgrade ratios of up to 1.26 in a single stage. A three-stage, rougher, cleaner and scavenger system did however show the best performance with recoveries of up to 70 per cent, yielding 56 per cent of a 63 per cent Fe product. Furthermore, the dewatering of the product and tailings was evaluated using the UltraG ultra-fine dewatering screen ensuring dry, stackable material. The tailings could be used in codisposal, while loads on thickeners and filter presses are significantly reduced. The high throughput of the Optima Classifier® ensures a small plant footprint, minimal civil and structural requirements and low operating utility consumption such as electricity, minimising the carbon footprint of a fines beneficiation plant. The Optima Classifier® in combination with the UltraG dewatering technology has provided a platform for economical recovery of fine iron ore, both current arising and historical. Providing opportunity to lower plant operating costs, reduce environmental liability of tailings facilities and increasing immediate process water recovery

Sep 18, 2023

By M Z. Abzalov

Drilling mineral sand deposits has specific challenges, which are different from drilling hard rock deposits: Drilled sequences are represented by non-consolidated free-flowing sands to semi-consolidated clayey sands and indurated layers. Valuable heavy minerals (ilmenite, rutile, zircon, leucoxene) have an average density of 4.6 g/cm3, which is significantly heavier than the hosting sand matrix; mainly represented by quartz (density = 2.6 g/cm3). The large difference in the mineral densities can result in sample segregation in the drilling rods and capturing devices causing biased composition of the recovered samples. The drilled strata can contain beds of consolidated sediments, hard pan lenses and concretions. Therefore, chosen drilling equipment should be flexible and permit a switch from drilling the free-flowing sands to hard rock drilling. Thickness of the sand hosted mineralisation varies from several metres to more than 170 m. Mineralisation is distributed above and below the water table. Evaluation of the mineral sands deposits is based on hundreds of drill holes and many thousands of samples, therefore drilling methods should be fast and cost effective. The drilling methods commonly used for mineral sand deposit evaluation, include aircore, triple tube diamond and sonic; including its variants, such as vibrocore drilling technique. The ability of the studied drilling techniques to properly address the above listed challenges in mineral sand deposits, whilst maximising the quality of the obtained samples has been compared in three deposits: Corridor Sands (Mozambique), Richards Bay (Republic of South Africa) and Fort-Dauphin (Madagascar).This study has shown that aircore samples tend to be negatively grade biased, underestimating the heavy minerals content, in particular when drilled intervals are located below the water table. Triple tube diamond core method can produce non-biased samples. However, results can be marred by incorrectly chosen drilling mud. Sonic drilling is a relatively new technique based on a high frequency vibratory technology. It is the only production drilling technique that allows a continuous relatively undisturbed sample of unlithified sands to be obtained. The main limitations of this technology preventing its wider use for developing mineral sand resources are the relatively high drilling costs, in particular when the depth of drilling exceeds 100 m, and speed of drilling advance.

Oct 5, 2011

The weathering profile, in arid terrains, is commonly capped by different kinds of hardened crust, whose formation is related to recent or former climates. One may distinguish silcretes, calcretes and the ferruginous (or ferro-aluminous) laterites. the present keynote address mostly deals with the lateritic regolith and, moreover, the influence it has on mineral exploration. The lateritic regolith, also called "cuirasse", is a result of a massive accumulation of Fe (and/or Al) oxides on top of weathering profiles developed during former, probably seasonal humid, climatic episodes, and whose preservation depends on the characteristics of later climates. The total thickness of such weathering profiles commonly exceeds 50 m, with an almost complete substitution of the rock forming minerals by secondary minerals as kaolinite and Fe-Al oxi- hydroxides (hematite, goethite, boehmite, gibbsite). Such an alteration of the primary minerals assemblage is of course accompanied by significant changes of the chemical composition, as concerns major and trace elements. The latter are distributed amongst the main secondary mineral phases or trapped in some primary resistant minerals, but may also be leached, totally or partially. Gold is also affected by lateritic weathering, as shown for instance by morphoscopic and geochemical studies of gold grains collected in the different horizons of the profile, which indicates some dissolution followed by reprecipitation.

Jan 1, 1988

By Hussey K. J, Morrison R. S

Recent mapping (1989-1992) by the Northern Territory Geological Survey in the Tennant Creek 1:250 000 map sheet area has resulted in substantial revision of the lithostratigraphy of the Tennant Creek Block (Donnellan, Hussey, and Morrison, in press). Briefly, the former Warramunga Group (Dunnet and Harding, 1967; Dodson and Gardener, 1978) is divided into the Warramunga Formation, and an overlying less deformed volcano-sedimentary succession, the Flynn Subgroup. The latter is conformably overlain by the Tomkinson Creek Subgroup of the Tomkinson Creek province in the north of the Tennant Creek Inlier. These two Subgroups constitute the Churchills Head Group which is essentially equivalent to the Hatches Creek Group of the Davenport province to the south of the Inlier.

Jan 1, 1994

By M Fishwick Tapia

This paper was prepared and translated from the final report of the investigation into the Codelco Chile Salvador DivisionÆs air blast which occurred in the Inca-West area. In this section of the block cave mine, a stable arch formed covering an area of approximately 15 000 m2 . This zone subsequently collapsed producing a massive air blast. The collapse followed a series of planned extraction activities and occurred on 5 December 1999. This paper discusses the cave back arching event and the measures that were taken in order to induce the controlled collapse. This was to minimise risk to personnel, equipment and installations. The results obtained to date are presented.

Jan 1, 2000

By J Vann

The philosophical context of many activities in mine geology can be an important lever in adding value to operations. For mine geologists (including resource and grade control geologists) we argue that the tasks of problem formulation, observation and data collection, interpretation and modelling invoke various philosophical considerations whether the practitioner is aware of them or not.Constructing testable models to explain reality is the definitive aspect of any activity claiming to be ‘scientific’. A primary goal of mining geology is to build models that accurately predict reality to an acceptable degree and these include litho-structural, stratigraphic, grade control, resource or reconciliation models. What’s more, in mine geology we are often able collect additional drill samples or access new underground openings, for example, that can provide relatively rapid feedback on how predictive, and therefore useful, our models are. In this paper, we describe the key philosophical frameworks proposed for conducting scientific investigations, including falsification, the method of multiple working hypotheses and structural concepts of scientific theory. The strengths and weaknesses of these approaches are discussed and an attempt is made to relate them to activities undertaken by mine geologists. Common perceptions of what constitutes the scientific method have been dominated by how scientists do experimental physics and chemistry in particular. There are very important differences in the types of problem confronted in these experimental sciences compared to the ‘historical sciences’, such as geology, where the processes studied are unique and only evidential traces of past events are available. The philosophical implications of attempting to validate numerical geological models, such as resource estimates are also briefly considered.Some practical conclusions are drawn about how mine geology activities can be better implemented if practitioners are cognisant of the importance of philosophical considerations when attempting to gain new knowledge through a scientific investigation. We believe that the implications for creating additional value to a project or operation can be very significant when geology is applied by a practitioner with an understanding of the philosophical basis of the activities we think of as constituting a scientific investigation.Remember that all models are wrong; the practical question is how wrong do they have to be to not be useful? (Box and Draper, 1987, 74 p).The demand that theories be highly falsifiable has the attractive consequence that theories should be clearly stated and precise. If a theory is so vaguely stated that it is not exactly clear what it is claiming, then when tested by observation or experiment it can always be interpreted so as to be consistent with the results of the test. (Chalmers, 1999, 67 p).

Aug 22, 2011