Search Documents

This work was instituted to investigate the microscopic structure of brown coals by means of microtome sections cut from them. It was found to be essential to impregnate the coal with some material prior to cutting, because of its powdery and crumbly nature. Of a number of impregnating materials tried, e.g., glycerine gum, gelatine, by far the most satisfactory was paraffin wax. Samples of brown coals for section cutting must be moist. When obtained, they should be put immediately into air-tight tins, and, if they are not to be used for some time, it is desirable to keep them under water containing a small amount of formalin. If the sample is allowed to dry in air, it becomes too hard to be cut. It cannot be softened again even by prolonged soaking in water.PREPARATION OF COALSmall rectangular, blocks were cut from the sample with a chisel and a strong scalpel. The largest block prepared was 3·2 x 2·5 x 0·6 cm. The faces of the block from which sections were to be cut were approximately levelled before treatment. The block was then painted carefully on all sides with two coats of warm aqueous agar, approximately 2 %. This prevented crumbling and breakage of the block during treatment. When the agar was set, the block was placed in water, and all the air removed with a vacuum pump. The water was replaced first by alcohol, then by chloroform, by the usual step transference of a series of liquids, in each of which the block was placed for 24 hours: Ethanol %, 10, 20, 30, 50, 70, 85, 95, 100 (three changes); Ethanol-chloroform, 3: 1, 1: 1, 1 : 3, chloroform pure (three changes) '. The blocks were then embedded in paraffin of melting point 56-58°C. Fresh...

Jan 1, 1947

By Szwedzicki T

Uniaxial testing was performed on model pillars to determine the effect of width to height ratio on pillar and surrounding rock mass stability. Samples were modelled in a shape similar to that of dumbbell weights, with the centre representing

Jan 1, 1994

By Z Lianbi, Z Yibin, Z Youhong, P Bin

Without adequate soil available, it is difficult to rehabilitate a large area of acid mine waste dump with sustainable plant communities, which has a strong potential acid generation. In the present project, paste tailings capping method has been put forward to reconstruct plant ecosystem on acid mine waste rock dump. This rehabilitation method uses paste tailings as capillary break and plant growth media. The tailings used contained 26.3 per cent of particles of less than 20 ¦m which satisfy the requirement of grain of paste tailings preparation. The tailings are not acid- producing materials. In addition to Cu, total contents of Zn, Pb, Cr, Cd, As and Ni in tailings are lower than those in local soil. Paste tailings concentration 70 per cent ~ 72 per cent was prepared by concentrating ten per cent tailings by using polypropylenecrylic sodium as flocculation. The potential pollution risks are low by using paste tailings as capillary break layer. Plants directly grown in the tailings did not particularly accumulate Cu, Zn, Pb, Cr, Cd, As, Ni in roots, stem and leaves, which were 0.01 ~ 1.6 times of those grown in soil.CITATION:Yibin, Z, Lianbi, Z, Bin, P and Youhong, Z, 2012. Study on paste tailings capping ecology reclamation on acid mine waste rock dump, in Proceedings Life-of-Mine 2012 , pp 243-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By J Lapwood, S Pal, M Pascoe

The devastating failure of Dam I at the Corrego do Feijao iron ore mine near Brumadinho in Brazil on 25th January 2019 left at least 270 people dead or missing. In the immediate aftermath of this event, many mining companies commenced reviews of their tailings and water storage facilities (T&WSFs), and Rio Tinto was no exception. Rio Tinto has an interest in over 250 T&WSFs across 47 sites in 13 countries as owner-operator, as managing JV partner, and through non-managed partnerships and other ownership arrangements; T&WSF experts from Rio Tinto’s Surface Mining Centre of Excellence visited the sites in order to complete Technical Risk Reviews of each facility. These reviews looked beyond the day-to-day operational aspects of T&WSF management, and the site’s compliance with local regulations and Rio Tinto’s internal D5 Standard – Management of tailings and water storage facilities, in order to provide a strategic, second line of assurance perspective. The reviews focused on design and construction; operational controls; risk control framework; and competencies and capabilities of personnel involved in the design, operation and closure of the facilities. Additional activities were carried out in parallel with these reviews, including the development of a consistent approach to dam break studies; the public disclosure of information on Rio Tinto’s tailings storage facilities and their management; and contribution to external programs such as the initiatives being co-ordinated by the International Committee on Mining and Metals. This paper provides an overview of the tailings and water storage assurance work undertaken by Rio Tinto’s Surface Mining Centre of Excellence Tailings Validation Taskforce to date; work that will continue to improve governance and assurance for all of Rio Tinto’s T&WSF.

Jul 1, 2021

By N Guresin, A Cooper, L Lorenzen, H Muller, S C. Dominy

Sampling and metallurgical test work during various phases of engineering?studies?is of?paramount importance for a robust processing plant design. When developing a process flow sheet, risks in achieving desirable financial outcomes are minimised by ensuring appropriate sampling and adequate metallurgical test work supports the engineering and cost estimation at each phase of project development.The quality and type of samples used for metallurgical test work are just as important as the metallurgical test work itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should take into account the spatial orientation, lithology, alteration, degree of oxidation, mineralogy and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical test work program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design.Snowden has observed that the quality of sampling and quantity of metallurgical test work carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are often the result of the plant design based on benchmarks of apparently similar orebodies or buoyant metal prices supporting cash flows until rectifications can be implemented.The paper will discuss important aspects of sampling and test work required for engineering studies in designing process plants based on industrial case studies.CITATION:Guresin, N, Lorenzen, L, Dominy, S C, Muller, H and Cooper, A, 2012. Importance of effective sampling and test work protocols for process plant design, in Proceedings Sampling 2012 , pp 95-108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By J Johansson, B Johansson

The mining industry needs to attract and recruit young talented people. An important task is, therefore, to create an attractive mining workplace that engages with, and motivates youngsters who are not particularly interested in working in the industry. This paper aims to illustrate a way forward for the mining industry to form healthy and safe workplaces honouring key components such as knowledge, skill, co-operation, continual development and acceptance of diversity. This is a way to create a vision of healthy and safe mining work. The mining industry must work towards zero vision; a future without accidents and hazardous environments. In this paper the authors discuss different aspects of an ‘attractive workplace’ and summarises lessons learnt in 26 statements dealing with safety, both physical and social work environments, and social responsibility. The authors hope these recommendations will provide some guidance for how attractive workplaces should be designed for future deep mining.The paper is based on lessons from two large European projects, a Swedish-Polish project: The Smart Mine of the Future; and a European Union project: Sustainable Intelligent Mining Systems (SIMS). One of the authors was the WP leader of health and safety in both projects.CITATION:Johansson, J and Johansson, B, 2017. Attractive workplaces in future underground mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 99–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By E M. Jones

On 26 June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19 000 m3 of saturated hydraulic fill into the mine, which caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at NormandyÆs zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the mine adjacent to Scuddles, Gossan Hill had progressed to a point where a self-supporting fill material was required to enable full recovery of high-grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16 July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in situ performance.

Jan 1, 2008

By R Whittering, C Greet

High chrome grinding media has been used in the mining industry for quite some time, as it often proves economical on a wear basis. However, it is unusual for an operation to change to high chrome solely due to its metallurgical benefits. KagaraÆs Mount Garnet operation made the change from forged steel to high chrome media after laboratory testwork indicated that copper grades and recoveries would improve. The outcome was remarkable with positive changes in pulp chemistry throughout the circuit accompanied by marked improvements in copper, lead and zinc grades and recoveries. Reagent dosage rates were reduced, often by more than half, and the grinding media wear rate dropped to less than a third of the wear rate of the forged steel media. The economic analysis showed that out of the total increase of revenue and savings from metallurgical improvements and reagent and media consumption reductions the metallurgical improvements made up approximately 73 per cent, the reduced reagents saved 25 per cent and the savings through reduced media wear contributing by just over one per cent. This indicates that the popular view of high chrome media only being trialled in the plant for wear economics is outdated and the focus of operations should be shifted to using high chrome media for the metallurgical benefits.

Jan 1, 2006

By H Kurth, L Balzan

The potential for bulk diversion was identified and quickly implemented following the development of bulk sensing technologies applied to conveyed flows. In the early 1980s real time analysis of ash in coal was intended to improve the understanding and control of quality variability. By the end of the 1980s approximately 5% of coal analysers installed were being utilised for bulk sorting; diverting flows to create stockpiles to improve blending flexibility and boiler feed consistency, diverting waste material, or bypassing the beneficiation process when the coal met product quality criteria. In the 1990s bulk sensing and sorting utilising natural gamma detection was applied to conveyed waste in gold-uranium mineralisation and allowed ore to be recovered and processed that would otherwise have been discarded. Further applications developed in the iron ore sector where product quality ore could be diverted to bypass beneficiation and save significant unnecessary processing costs and improve recovery by avoiding process inefficiency losses. Plant capacity was freed up to be utilised by material that required processing. Similar benefits became evident in the phosphate industry and in base metals where multi-elemental analysis using Prompt Gamma Neutron Activation Analysis provides ideal opportunities to representatively measure 30 second conveyed increments at high accuracies. This has been successfully adopted in copper, nickel, platinum and lead-zinc to improve waste removal after primary crushing to eliminate unnecessary expense and improve plant efficiency. The benefits include increased output from existing operating capacity, significant reductions in consumable costs and generation of fewer detrimental waste streams. The paper outlines the technologies and discusses case studies covering the above commodities, demonstrating the immense value that representative real time measurement of conveyed flows can create. Measurement data concurrently provides multiple benefits in operational performance besides sorting, through ore reconciliation, ore blending, feedforward control and metal accounting, adding further value.

Nov 10, 2020

By Etheride MA

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems an particularly prone to developing the complex fracture arrays, extreme local dilation and dramatic increases in permcahilit} that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits.

Jan 1, 1995

During the last few years the quality requirements on roads and railroads have become more accentuated due to the desire to minimise maintenance costs. This has, in turn, led to increasing requirements in the preparation of ballast materials and pavement aggregates. As the access to natural gravel in northern Europe is decreasing (due to lack of availability or by law restrictions) the use of crushed rock material is becoming more and more important. The aim of this paper is to derive and describe a universal method for the prediction of particle size distributions from compressing crusher machines such as jaw- and cone-crushers. Based on a closely defined physical model, expressions which define the size reduction process are derived. Conditions for simplifying assumptions are clearly outlined. The choice and mix of breakage functions is a central subtopic iò the analysis of the crusher machine processes. Known breakage functions are reviewed and evaluated. A new concept for determination of a true breakage operator which is related to physical properties of the crusher device and the size distribution of the feed material is introduced. Finally experimental tests are compared to numerical calculations. The method described in the paper can be a useful tool when designing crushing plants or when optimizing the output of compressing crusher Machines.

Jan 1, 1995

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By F Carrick, W A. Ellis, D R. Mulligan, S I. FitzGibbon

"One of the major environmental impacts of mining is the destruction of habitat. The koala (Phascolarctos cinereus) is an iconic Australian marsupial that has been severely affected by land clearing and its decline is continuing. This has placed pressure upon mining companies and government agencies to ensure koalas are managed throughout the life-of-mines - from land clearing through to rehabilitation of post-mining landscapes. This paper reports on the æKoala VentureÆ research partnership between The University of Queensland and Rio Tinto. As part of the Koala Venture program we examined koala use of two types of restored environments: rehabilitated mined land (20 sites) natural regrowth forests (six sites), at Blair Athol Coal Mine in Central Queensland, Australia. Searches for koala scats revealed evidence of koalas in ten per cent of rehabilitated sites (2/20) and 33 per cent of natural regrowth sites (2/6). Two factors were identified as being of greatest importance in facilitating koala recolonisation of restored habitats. Firstly, all recolonised sites were located close to native forest occupied by koalas (mean 135 m ¦ 52). Proximity to source animals is considered crucial to recolonisation of suitably restored habitats. Secondly, three of the four recolonised sites were dominated by koala food trees, most of which were large enough to be utilised by koalas. Availability of suitably abundant food resources is, therefore, also considered crucial. The requirement for these two factors, in combination, is highlighted by the absence of koalas at several sites that contained abundant food trees, but that were distal to areas with source animals, and vice-versa.Our research demonstrates the enormous potential for restoration of wildlife habitat on post-mining lands, even for species with specific requirements such as the koala. Consideration of the ecological requirements of wildlife during rehabilitation planning is critical to enhancing the likelihood of recolonisation.CITATION:FitzGibbon, S I, Ellis, W A, Mulligan, D R and Carrick, F, 2012. Rehabilitating post-mining landscapes for wildlife - A case study from the Koala Venture research program in Central Queensland, in Proceedings Life-of-Mine 2012, pp 319-324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

A forecast of energy demand in the non-commu- nist world to the year 1990 is presented with com- ments on the expected effectiveness of conservation efforts in achieving more efficient utilization of energy. A forecast of energy supply for the same period is presented showing the contribution of oil, gas, hydropower, coal, and nuclear fuels, with brief comments on the factors constraining the rate of growth of non-oil energy supplies. The role of `synthetic fuels', i.e. liquid or gaseous fuels produced from coal, oil shale, and tar sands, is reviewed with brief discussion of factors affecting the development of this industry. In somewhat greater details, the growth of demand for oil by geographic regions is analyzed. Particular attention is directed to the source of the oil supplies which will be required. The anticipated rate of discovery of new oil reserves is discussed with comments on lead times required in the development of new discoveries in hostile environments such as the Arctic and deep oceans. The continuing importance of oil supplied from countries which are members of the Organization of Petroleum Exporting Countries (OPEC) is illustrated. Oil will continue to be the marginal ('balancing') source of world energy supply throughout the forecast period and although it now appears that oil supplies will be sufficient to balance the energy equation during the 1980s, little flexi- bility will exist to cope with unexpected growth in demand or slippage in supply. Prudent energy re- source management will require major efforts to stimulate conservation and also to stimulate the rapid development of conventional and new forms of energy supplies and changes in energy consump- tion patterns to utilize the new supplies. Because of the long lead times and the massive capital require- ments involved, governmental policies are needed soon which will stimulate conservation and which will encourage businesses to move rapidly to assure the energy supplies the world will require in the 1990s.

Jan 1, 1978

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

By C Morley, B Costello

In 2002 the Argyle Diamond Mine upgraded the process plantÆs recrush circuit to include a High Pressure Grinding Roll (HPGR), or High Pressure Rolls Crushers (HPRC) as they are termed in the diamond industry. HPGR have generated considerable interest over the last decade, though there are still technical/processing unknowns to its effectiveness as a primary diamond ore crusher.The upgrade of the Recrush circuit at Argyle Diamonds has gone a long way to answering some of the key questions, and thus it has reduced the unknowns to a level more acceptable to the industry.This paper focuses on the results from the HPRC at Argyle, in particular the performance of the studded wear surfaces, comparison of energy efficiency against traditional quaternary cone crushers and the resultant increased liberation. Issues that have arisen, including edge wear of the studded surfaces, will be discussed and the steps taken to reduce this issue are presented.

Jan 1, 2004

By E Jak, P Hayes, J Chen, M Shevchenko, E Nekhoroshev, D Shishin

Recent decades have seen significant advancements in analytical and experimental techniques, thermodynamic theory, and computational capabilities in high temperature research which are particularly timely to address the challenges of increasingly complex and variable feedstocks in both primary and secondary pyrometallurgical processes, the need to optimise and improve them. Currently a research program is in progress on the development of the 20-component multi-phase thermodynamic database for pyrometallurgical smelting, refining and recycling systems describing thermodynamics and phase equilibria of molten slag, matte, speiss, salts, alloys and associated solids. The integrated experimental and modelling program has been supported for nearly two decades by several consortia of 14 major international companies with over 30 operations around the world, integrates many components, incorporates many in-house developments, and brings together many different groups of professionals of different levels from junior and mid-career to senior from both industry and university sectors. The aims of the paper are:  to outline the many components and issues of the overall program including analytical, experimental and thermodynamic modelling research as well as implementation of the results in industrial practice, professional education, planning and organisation issues.  to highlight the opportunities, challenges, and possible solutions.  to present these to all different groups of professionals involved in the current program.  and thus, importantly, to facilitate possible future further developments and collaborations in the field of phase equilibria and thermodynamics of complex high-temperature systems.

Jun 19, 2024

By G Tsatouhas, R Newell, K Y. Wong

A sulfide ion selective electrode was used to control sulfidiser addition in the flotation testing of a synthetic and a naturally occurring ore containing malachite in order to compare the behaviour of sodium sulfide and calcium polysulfide. Both slug and controlled potential sulfidisation methods of addition were used. Under defined optimum CPS conditions, calcium polysulfide was a more effective sulfidising agent than sodium sulfide on the basis of both capital and operating costs. Surface and solution studies were used to compare the mechanism of each sulfidiser. For calcium polysulfide, XPS showed that polysulfide ions are adsorbed, whereas for sodium sulfide it is the hydrosulfide ions that are adsorbed on the mineral surface. For calcium polysulfide, the CuSx layer was believed to form on the malachite surface, which promoted the flotation of the malachite, by xanthate. Studies of surface morphology of the sulfidised malachite showed that a fairly uniform sulfidised layer is formed with both reagents. The use of sodium sulfide resulted in a thinner initial sulfidised layer compared to polysulfide at equivalent initial sulfur concentration.

Jan 1, 2005

By Howarth W. J, Sowerby B. D, Watt J. S

On-line analysis systems have found widespread application in the metalliferous mineral and coal industries. The continuous analysis and rapid response of these systems has led to improved control of mining, processing and blending operations, with increased recovery of valuable minerals and coal combustibles.The paper reviews developments in on-line analysis by CSIRO and Mineral Control Instrumentation Ltd which led to the award of the Australia Prize 1992. These commercialised systems analyse mineral and coal slurries; determine the ash and moisture contents of coal on conveyors, and the moisture content of coke on conveyors; and determine the carbon content of fly ash. These gauges are estimated to have resulted in productivity increases valued at $50 million per year to Australia.

Jan 1, 1993