Search Documents

By Francis Freeland

An examination of accessible English literature shows that but small space has been allotted to the determination of faults ; most suggestions being confined to Schmidt's rule of the downthrow on the hanging-wall of the fault, or the coal-miner's rule of the obtuse angle. Von Carnall's modification of Schmidt's rule is sometimes given without the important exception, and Zimmermann's rule is

Jan 1, 1893

By V. A. Josendal, J. W. Wilson, B. B. Sandiford

Two radioactive tracers have been tested as a means of determining core saturation in multiphase flow studies. Cesium chloride was tried as a water-phase tracer, but complications in its use in low permeability cores resulted from sorption of cesium by the core or water-wet pads. IodoI3'ben-zene proved very satisfactory as an oil-phase tracer. The synthesis of iodobenzene from the sodium iodide as received from Oak Ridge is simple and direct. The tracer is insoluble in water and there was no evidence of sorption by any of the core materials used. use of the method to determine saturation profiles during capillary and dynamic desaturations and relative permeability measurements on oil-water and oil-gas systems is described. Comparisons of the dynamic and capillary methods of relative permeability determination were made using the tracer to check core saturation and saturation distribution. Other experiments are also described in which mobility of the oil phase at various saturations was measured by displacing labeled oil by flowing inactive oil. Similar experiments were made using water labeled with cesium 134. INTRODUCTION To be fundamentally sound. any laboratory method of determining relative permeability must meet, among others, the following requirements: (1) the core saturation between the pressure taps must be uniform, and (2) there must be uniform pressure difference between the phases in the region between the pressure taps. In practice it may eventually be shown that appreciable departure from either or both of these conditions may be permitted without introducing sensible error. but the magnitude of such error remains to be established. There is need then for methods of saturation determina- tion which will determine the saturation profile in a core as well as the overall average saturation given by the gravimetric or material balance methods usually employed. Methods which have received consideration include resistivity, X-ray absorption, gamma ray absorption, neutron diffraction, and radioactive tracers. The resistivity method has use in the determination of profile, but needs checking by independent means.' The X-ray method has been used successfully, but requires elaborate equipment and calibration.23 4 At present gamma ray absorption is practical only for very large cores. The neutron methodo does not appear adaptable to measurement of saturation variations in short cores since it is a scattering method. Russell, Morgan and Muskat' employed radiovanadium in a study of the mobility of interstitial water. Coomber and Tiratsook used radioiodine as an oil-phase tracer and measured profiles in unconsolidated sand packs. ADVANTAGES OF RADIOACTIVITY METHOD A thorough discussion of the theory of radioactive tracers and the technique of using them to study the movement of fluids in sands is given by Coomber and Tiratsoos and need not be detailed here. The method requires less equipment than the X-ray method; the counting problem is similar, but the generation and regulation of the radiation, which is a major problem in the X-ray method, is not required in the radioactivity method. In the X-ray method it is customary to add up to 20 per cent of absorber, usually an iodine compound, to the phase to be labeled. while in the radioactivity method a mere trace is sufficient. A possible disadvantage of the radioactivity method is that a disproportionate amount of the activity comes from the portion of the core nearest the counter, whereas the X-ray gives a true average saturation in the region traversed by the beam. 011 the other hand, this characteristic of the radioactivity method renders it peculiarly adaptable to study of certain types of radial variations in saturation. As with the X-ray method, a tracer may be added to either the oil or water-phase. An oil-phase tracer is more generally useful. however. since it permits work on oil and gas in the

Jan 1, 1952

By Fritz F. Prugger, Peter R. Jones

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate to mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province’s mines. Mining layouts, materials handling, and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1983

By J. E. McDonald, J. G. Eberhart

A model is discussed from which the work of adhcslon .tor liquid transition metals on aluminum oxide surfaces can he calculated, A close-packed (00011 oxygen surface on A12O3 is assumed with two different types of surface sites: one type involving metal-oxygen bonds and the other man der Waals into actions. The work of adhesion is thus expressed as the sum of these two bonsding free energies. Calculated works of adhesion for nickel, titanium, chromium, and zirconium on sapphire agree well with the experimentally determined quantities. The model is extentled to the calculation of the work of adhesion and shear stress required to remove a thin metal film from a sapphire substrate and is in good agreement with experimental values. The obsewed dependence of the work of adhesion on the free energy of oxide formation of the metal is shown to also provide an interpretation of the tittle dependence of thin-film adhesion. THIS paper presents a model for the type of bonding which occurs across a metal-A12O3 interface. The model is used to explain the results of two types of experiments in which such an interface exists: 1) the adhesion of thin metal films on Al2O3 substrates and 2) the wetting of A12O3 by liquid metal drops. The adhesion of thin films to various substrates has been the subject of a variety of investigations.'-' Benjamin and weaver3 and Bowie,6 using the scratch test developed by Heavens,10 studied the adhesion of metallic films to glass substrates. Their observations for noble-metal film adhesion agree well with an adhesion model involving a van der Waals type of bonding between the film and the substrate. For films of metals whose free energy of oxide formation. ?F°f, has a negative value. Benjamin and weaver3 and Bowie6 found a time-dependent adhesion with an initial value that can be interpreted in terms of van der Waals interactions but a larger terminal value which was related to ?F°f, Karnow-sky and Estill7 deposited films on sapphire at elevated temperatures and noticed no time dependence of film adhesion but a similar correlation with ?F°f. Because of the kinetic problems associated with thin-film adhesion it is desirable to examine adhesion in an equilibrium system. The wetting behavior of liquid-metal drops on Al2O3 provides such a system. Systems of this metal-ceramic type have been studied extensively.11 Humenik and Kingeryl2 have measured the wetting of A12O3 (and other substrates) by several metals and have pointed out that the wetting ability of these metals increases with increasing values of -?F°f. It is thus seen that thin-film adhesion and metal wetting on A12O3 are both related to the tendency of the metal to react with the surface oxide ions of the Al2O3 substrate and, because of this, both phenomena should be explainable by an appropriate model for the metal-Al2O3 interfacial bonding. In the sections that follow, wetting and adhesion data on A2O3 are reviewed and a model is presented by which these phenomena can be interpreted. ANALYSIS OF WETTING EXPERIMENTS In an equilibrium system involving a liquid-metal drop on a solid Al2O3 substrate, the work of adhesion, WAD, is defined by the Dupre, equation as WAD = ?s + ?L -?sL [1] where ?s and ?L are the surface free energies of the solid substrate and the liquid drop, respectively, and ?sL is the interfacial free energy. The work of adhesion is the work required to separate a unit area of the solid-liquid interface into two surfaces. The work of adhesion is usually determined from a sessile-drop experiment in which yL and the contact angle, ?, are measured. The Young-Dupr6 equation is then used to calculate WAD Wad = ?L (1+ cos ?) [2] The literature of this subject has been examined and Table I shows work of adhesion data for various liquid metals as measured on A12O3 substrates. The standard free energy of oxide formation of the metal at the temperature of the wetting experiment, ?F°f . is also tabulated in kcal per g-atom of oxygen. The data is grouped according to the gaseous atmos-

Jan 1, 1965

By Thomas E. Ban, Charles D. Thompson, Charles A. Czako

Continuous sintering-a metallurgical process for more than 50 years-has broadened from its origin in nonferrous metallurgy to present-day applications in ferrous, chemical, and nonmetallic fields. During the past year, self-fluxing sinter production has been a subject of active interest to iron metallurgists in North America. Accomplishments however, have come predominantly from Europe and proper interpretation of these reports requires an understanding of European raw materials and European economics. The technology, of course, can be applied universally.

Jan 10, 1959

By Robert J. De Angelis, James H. Barker

An improved method for solving dynawzical dislocation problems using a digital computer is described in this paper. Interactions between two distinct types of dislocations were studied: attractive screw dislocations; and Lomer lock forming dislocations. One dislocation is positioned in the lattice and is initially at rest, while the other dislocation is moved through the lattice on an intersecting slip plane at a constant velocity in the range 0.5 to 0.999C. (C is the transverse velocity of sound.) The results obtained from these computations indicate that screw dislocations account for a small fraction of the total strain over a wide portion of the range of velocities studied. They further indicate that mixed dislocations mainly repel other dislocations in the neighborhood of the active glide plane. From this a possible explanation for cell formation is put forth. The density of Lomer locks expected to exist after a strain of 0.2 was found to be 1.4 x 106 cm-2 which is in good agreement with indirect experimental estimates. IN the past, predictions of favorable or nonfavorable dislocation reactions were based on the associated changes in elastic strain energy. Such considerations take no account of the probability of the two dislocations coming into contact to react. Venables1 was the first to approach these probabilities by considering the interactions between two moving screw dislocations on perpendicular glide planes. Because of the restrictive types of dislocations and glide plane geometry employed, his results have limited application to metallic crystals. The work to be presented here develops a general approach to solving dynamical dislocation problems; either dislocation-dislocation interactions, presented here in detail, or dislocation interactions with any other suitably defined stress field. Two types of dislocation-dislocation interactions common to face centered cubic (fee) materials are considered: those between pure screw dislocations of opposite sign on intersecting slip planes and those between mixed dislocations on intersecting slip planes, that can react to form a perfect dislocation. This latter reaction, referred to as the Lomer reaction, produces a locked product dislocation that finds it energitical favorable to disassociate into two Shockley partials and a stair-rod dislocation. This partial configuration known as a Lomer-Cottrell (L-C) lock plays a major role in work hardening of fee crystals. seeger2 names the L-C lock as the prime contributor to Stage II hardening while Kuhlmann-wilsdorf3 and Meakin and Wils- dorf4 also state that it is a significant contributor to work hardening. However, with a few notable exceptions,5-7 direct observations of the Lomer lock and the L-C lock by electron transmission microscopy are scanty, and even these are subject to other interpretations.5,6 In a study of partial dislocations present in austenitic stainless steel, whelan8 did not observe any L-C locks at the head of pile-up groups. This result contradicted existing work hardening theories and led him to postulate an alternate theory based on the stress required to break away dislocations intersecting a pile-up group, from their stacking fault nodes. Due to the importance of the Lomer reaction in producing L-C locks which are an essential feature in current work hardening theories and because there exist no data giving direct quantitative values for the density of locks, and because there has even been some doubt expressed as to whether this important reaction occurs at all, a study of the dynamic behavior of the mixed dislocations which form the Lomer lock was undertaken. Due to their ability to cross-slip with relative ease, screw dislocations play an important role in the deformation of fee crystals. For this reason, the second type of reaction considered here is between screw dislocations of opposite sign. In addition, computations in volving screw dislocation interactions are relatively simple, thus providing a convenient check on the cornputational scheme employed. DEFINITION OF PROBLEM The force exerted on a dislocation due to a generalized stress field is given by the Peach and Koehler9 equation: Here t2 and b2 are respectively the tangent and Burgers vectors of the dislocation, and T1 is the stress dyadic defining the local stress field. The stress field may be externally applied or generated internally by the presence of a lattice defect, such as a second dislocation, as is the case in this work. Frank10 has shown that an equivalent momentum, P, of a screw dislocation can be defined by: Here, EST is the total energy of a screw dislocation and ESo is its rest energy. The left side of Eq. [2] is the time derivative of momentum and the right side is the position derivative of the energy due to the dynamical nature of the dislocation. The total energy of a dislocation is the sum of the potential and kinetic energies. Weertman11 has developed the expressions which were used here; these give the potential and kinetic energies of uniformly moving edge and screw dislocations in an isotropic medium.

Jan 1, 1969

By O. D. A. Pease, C. D. Young, C. H. Strand

In an effort to employ cast steel of a stronger structure than that found in the annealed steel casting, the possibilities of heat treatment which will increase the strength without materially decreasing the ductulity may be resorted to.

Jan 1, 1915

By Shiro Ban-ya, John F. Elliott, John Chipman

The activity of carbon in Fe-C austenite at 1150°C has been determined for concentrations up to about 2.1 pct C using the equilibrium: C + COz = 2CO; equations have been derived expessing the activity as a function of carbon content on the basis of twelve mathematical models. Several of these represent the data satisfactorily. ACCURATE information on the thermodynamic properties of austenite in the binary system Fe-C is needed as a basis for studies of transformation and precipitation in steels of all sorts, alloy as well as plain carbon. The many attempts to approach this problem through statistical thermodynamics require sound and dependable experimental data in order to evaluate the several models which have been suggested. In this paper we are concerned with the experimental determination of the activity-composition relation in austenite at the temperature of its widest range of stability, approximately the eutectic temperature (1153°C). Accurate investigation of the activity of carbon in austenite may be said to have begun with the work of Dunwald and wagner.' A more detailed study was carried out by R. P. smith2 on the two equilibria: More recent work on these two equilibria has been reviewed by Chipman,3 who pointed out the experimental hazards associated with studies of Eq. [I]. Studies of this reaction involve rather small values of the ratio these are susceptible to errors due to traces of moisture in the apparatus according to the reaction: Ellis, Davidson, and Bodsworth4 evaluated K, for their experimental temperatures and used desiccants to control water vapor pressure. While they were able in this way to obtain consistent values for K1 it cannot be said that all of the uncertainties of the method have been overcome. Results by both methods reported by Schurmann, Schmidt, and wagener5 appear to be consistent except at very low carbon content. Reaction [2] was employed in the experimental work reported here. It is to be recognized, however, that it is not applicable to projected studies of certain alloy steel compositions involving stable oxide-formers.

Jan 1, 1970

By A. A. Dor

Out of nine new major iron ore concentrators put in operation during the last three years, or expected to be commissioned in 1968, seven incorporate primary grinding mills and have a total design capacity of 13,150,000 ltpy of pellets, while only two include conventional rod and ball mill grinding circuits for a total design capacity of about 6,100,000 ltpy (Table I). This evolution in the application of primary grinding to hard, fine grained magnetite ores represents an important development in the technology of mineral processing. It has been the outcome of comprehensive testwork in the laboratory and in pilot plants.

Jan 11, 1968

Falconbridge Nickel, the one-time subsidiary that grew up to swallow its own parent, Ventures Limited, in 1962, is not about to be left behind by rising nickel consumption. At a cost of several hundred million dollars, this Canadian firm has undertaken a series of new projects that will not only ensure its present share of the market, but also lead it into new areas of the nickel business. Although Falconbridge Nickel Mines Ltd. was not formed until 1928, it actually had its start in 1917- 18 with the discovery of a large, good grade nickel- copper deposit in Falconbridge, near Sudbury, Ontario. However, due to several factors, financing could not be obtained and the orebody lay fallow. It was not until 1928, when the Thayer Lindsley interests bought the property from the original owner, that it was developed.

Jan 10, 1968

By Dan G. Cojocariu, E. Ene-Danalache, I. Huber-Panu

A general model which represents not only batch but also continuous flotation in multi-cell machines is presented. This model considers both the size distribution and the distribution of flotabilities in a size class for valuable mineral particles in the pulp. The general expression is shown to reduce to several previously reported models. In addition, a number of new models are found to arise for different specific assumptions concerning the flotability distribution and/or the size distribution of the particles undergoing flotation. Several of these new models are tested experimentally using laboratory-scale batch and pilot-scale continuous data. Model parameters are estimated from this data and a comparison of calculated recoveries and those experimentally determined are presented. Finally, the influence of the feed rate, aeration rate and valuable mineral content of the feed on the recovery is examined.

Jan 1, 1976

By E. P. Pfleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed pressure, see Fig. 2. The

Jan 1, 1952

By L. E. Wemple

Previous to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, ie., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, z.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was predetermined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into grades suitable for bras4 was that of redistillation.

Jan 1, 1918

By O. H. Eschholz

THE electrostatic process of fume precipitation is an excellent example of the successful application of scientific knowledge to an industrial operation. Originally proposed for the precipitation of sulphuric acid mists, it has been extended until at present there is practically no fume carrying gas to which the method cannot be applied. Among the more common applications are: the recovery of non-ferrous smelter flue-dust, iron blast-furnace dust, cement dust, and potash fume. It should be borne in mind that the process is restricted to the precipitation of suspended particles, either liquid or solid, and does not separate gaseous constituents. However, -by proper temperature control, mixtures of vapors having different temperatures of condensation to either solids or liquids may he selectively precipitated. The process consists essentially of subjecting suspended particles, including those too minute to be effectively acted upon by centrifugal or gravitational forces, to such an electrical force that they are driven from the gas stream, acting as a conveyer, and deposited upon a suitable receiving surface. This directional impulse is obtained front the interaction of charged particles and an electrostatic field of definite intensity gradient existing between two dissimilar electrodes, known as discharge and receiving electrodes. In principle, the equipment is equally simple. As shown diagrammatically in Fig. 1, it consists of: (1) A source of high-potential direct current, requiring: (a.) Source of alternating-current energy. (b) Means of transforming from tow voltage to high voltage. (c) Means of converting alternating to direct current. (2) Precipitation chamber having: (a) Transmission tubes for fume-laden gases. (b) Suitably designed and disposed electrodes. (c) Means for affecting removal of deposited solids.

Jan 8, 1918

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By Maurus Seet

Mainland China, with one-fourth of the world's population and one-tenth of its coal production, can no longer be ignored as a considerable force on the world energy scene. In terms of annual productivity, China's 300 million tons of coal rank third behind the Soviet Union with 655 million and the United States 557 million (1968 Minerals Yearbook. USBM). When viewed from another angle, 1967 figures show that increased productivity from all coal-producing continents, with the exception of North America, was led by Chinese-dominated Asia with a 19% gain. Not unpredictably though, China, on a per capita basis, is closer to the bottom of the list among members of the industrial community. Despite its misspent youth, and despite the set- backs caused by the Big Leap Forward of the late 50's and the Cultural Revolution of the late 60'S, the People's Republic has managed to make some impressive strides in developing its coal industry over the past twenty years.

Jan 1, 1971

By James Johnston

Synopsis.-A description of the working of the mills of this company and the metallurgical practice in vogue, by which a remarkably. complex silver ore, averaging 54 oz. of silver per ton (run-of-mine ore), is treated to give a 95.66 per cent. extraction. The main features of the, processes are: The cyanide amalgamation of the high-grade ore. The cyanide treatment of the low-grade ore, after extremely fine grinding and close classification, in a caustic soda solution. The use of a wet desulphurizing process to break up refractory silver minerals. The substitution of aluminum dust for zinc dust as a precipitant. The recovery and shipment of over 13,000,000 oz. of silver in bullion at. 997 to 999 fine since this metallurgy was inaugurated, about 2.5 years ago. On the completion and successful operation of the mill to treat their . high-grade ore,1 the Nipissing Mining Co., under the general management of R. B. Watson, started a series of investigations of the possible treatment of the low-grade ore by the cyanide process, so that they would be in a position to market only silver bullion. These tests were run in July, 1911, on a large scale, by G. H. Clevenger, on an average mixture of Nipissing ore. The results obtained by a partial amalgamation followed by cyanide treatment gave an extraction varying from 90 to 93 per cent. and were sufficiently encouraging to warrant Charles Butters, the company's Consulting Metallurgist, in recommending that the new low-grade ore mill under contemplation should be a cyanide mill, instead of a concentrator. The cost of such a mill, capable of treating 200 tons per day, to obtain a 90 per cent. extraction at a working cost of $3 per ton of ore treated, was estimated at $250,000.

Jan 1, 1914

By Will B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 5, 1960

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack-poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet-for indeed the instrument is easier levelled, and, more-over, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity ; on the other hand, however, that correction

Jan 1, 1873

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope ; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet for indeed the instrument is easier levelled, and, moreover, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure Any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity; on the other hand, however, that correction