Search Documents

By J. S. Vanick

An extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applications requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small grain-grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.' It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963

By R. A. Thomas, R. L. Solbod

The importance of transverse diffusion on the finger development in a miscible-phase displacement at an adverse mobility ratio of tbree was studied in a porous plate 1/4-in. thick, 3-in. wide and 18-in. long. Fast displacement rates (29 ft/D) and slow rates (1.6 ft/D) were used to determine the effect of residence time on the geometry of the fingers. The shape of the fingers was observed directly by use of the X-ray technique. At fast rates numerous narrow fingers were observed, but at slow rates a single somewhat bulging finger was produced. The amount of material moved transversely by diffusion across the plate was sufficient to modify the finger geometry in the slow-rate run because of the long residence time. These results are in contradiction to some of the postulates in the literature. The composition of the effluent stream, however, was not affected by the flow rate. This result is not inconsistent with the observed change in the shape of the finger in a short model, but it seems likely that a short model does not offer adequate and proper scaling of the reservoir. The model used was probably a valid one for studying the effect of transverse diffusion on the finger geometry, but a longer model would be needed for proper scaling of the effect of the change in the finger shape on the efficiency of displacement as measured by the composition of the effluent stream. INTRODUCTION Fingering can be defined as the uneven advance of the injected phase as it moves into a porous medium displacing the resident phase from the pore spaces of the rock. The use of this term is usually restticted to the situation in which the displacing phase is less viscous or more mobile than the fluid being displaced. Under these conditions, not only are fingers formed, but the length and width of the fingers grow with distance traveled in the porous medium. This subject has become one of great interest to the oil industry because of the present trend toward the use of various forms of miscible-phase displacement to increase oil recovery. Since in nearly all of the known modifications of the miscible-phase displacements an unfavorable mobility ratio exists (the displacing phase has a lower viscosity than that of the crude oil), the conditions are proper for fingering to develop. An appreciable amount of fingering appears to be a severe handicap to these processes for it increases the volume of agent required for the process to be a success, and such an increase puts a severe strain on the economics of the proposed processes. In some cases, such as for a mobility ratio of 200 unfavorable, it has already been demonstrated that the proposed process would not be economic if the fingering in the field were to be of the same magnitude as that observed in the laboratory. A number of aspects of fingering have been studied and reported in the literature. While the phenomenon of fingering cannot be regarded as a completely understood subject, considerable information exists on the effect of the path length and the mobility ratio on the growth of fingers. Less-complete data are available on the effect of the diameter of the flow path on the character and amount of the fingering, and even less agreement in results exists on the effect of rate of flow on the nature of fingering. This paper deals with one aspect of this latter subject. OBJECTIVE The objective of this study was narrowed down to one rather specific feature of the behavior of fingers in miscible-phase displacement in porous media. The variable studied was the effect of rate of flow on the nature and the development of fingers. It should be made clear at this point that, while rate was the apparent variable, the real variable was residence time; that is, at low rates the fluids are present at a given spot in the porous medium for a longer time interval than at fast rates. The purpose of the study, therefore, was to determine the changes which occur in the fingering and the possible benefits which might accrue from a longer residence time during that period when fingers are

By H. E. Montgomery

H. L. Burghoff.*—I have a question, Dr. Smith. A number of the alloys you mentioned contain lead, which, of course, is present as discrcte particles. At what level of concentration does lead begin to play an important part in determining these elevated-temperature characteristics ? A. J. Smith.—That is a difficult question to answer because of the complicating features of the alloys that arc lead free. I do not know of any work done on the subject. But for comparison, 85-5-5-5 has about the same characteristics at, say 450°F. as 88-10-2, which is lead free or contains at most 0.30 per cent. Both 85-5-5-5 and 88-10-2 precipitate delta. The specification limit of usage is 406°F., temperature of saturated steam at

Jan 1, 1945

By Henry Mulryan

Diatoms are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skelctons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. Diatomites Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. Diatoms More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the freshwater diatomites on the Pacific Coast are: Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralfs Diatoma vulgare Dory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kützing Stictodiscus niagarac Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg Epithemia turgida Kützing

Jan 1, 1942

By Henry Mulryan

Diatoms are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skelctons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. Diatomites Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. Diatoms More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the freshwater diatomites on the Pacific Coast are: Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralfs Diatoma vulgare Dory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kützing Stictodiscus niagarac Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg Epithemia turgida Kützing

Jan 1, 1942

By John E. Conley

THE production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.1 The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnston,2 Smyth and Adams,3 Ralston et al.,4 Furnas,5 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894º to 898º C. The dissociation of dolomite and magnesite, although studied by several investigator,4, 6, 8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (1) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1939

By A. Kenneth Schellinger

THE terms surface tension .and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the minerals present.. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to. 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid: liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1952

By S. J. Kidder

The Mogollon mining district is in the southwestern part of New Mexico near the southern end of the Mogollon range, from which the district takes its name. The town of Mogollon is but 371/2 miles in an air line northeast of Clifton, Ariz. The air-line distance from Silver City is 521/2 miles and from Tyrone, 57 miles. Supplies are transported by motor truck from Silver City. The distance by road is 75 miles, half of which is an improved highway of modern construction. Transportation has always been a large item of expense in carrying on operations in the district. Valuable ore is said to have been discovered in the Mogollon Mountains as early as 1870 but the first regular prospecting was carried on in 1875, by James C. Cooney, a sergeant from Fort Bayard. His discovery of rich silver-copper ores in the region of Mineral Creek led to the establishment of the Camp of Cooney. Remote from any settlements where there was a semblance of law and order, and harassed by the Apaches, development was slow and nearly 10 years elapsed before the village of Mogollon was established on Silver Creek. Prospecting in this section of the district had disclosed the outcrops of several promising veins containing silver-gold ores. Among the early claims located were the Last Chance, Top and Confidence, on what has proved to be the most productive vcin in the district. To the end of 1922, the Last Chance and Top claims had produced approximately 600,000 tons of ore and nearly 200,000 tons had come from the Confidence group of claims. The total value of the ore produced from this vein alone has amounted to about $9,600,000 in silver and gold. The Fanney vein was developed later and during its most active period of production contributed more than half of the output of the district. Other important locations, though far less productive than the above, were the Maude S, Deep Down, the Deadwood and the Pacific.

Jan 1, 1925

By W. B. Phillips

The earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in " Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. ***** The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would be thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.' In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114, Township 6, contains 79.08 grains of free sillphuric acid per gallon. This locality is about 13 miles (21 km.) south . of Delaware Creek and about 35 miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos. Texas is in the Pirst Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 1, 1918

By C. M. Young

The following paper has been prepared with the object of placing on record in the Transactions some facts concerning the present condition and future prospects of the coal industry of Illinois. In presenting it, the writer wishes to say that a considerable amount of the material contained is taken from the publications and records of the Illinois Coal Mining Investigations, the annual Coal Report of the State Mining Board, and the work of the State Geological Survey. Coal Beds and Mining Methods According to the latest maps of the State Geological Survey, there are only 19 of the 102 counties of the State some portion of whose territory is not within the borders of the coal measures. If outlying areas in Calhoun and Whiteside Counties are considered, the number is reduced to 17. This does not mean that all of the 85 counties that are partly or wholly underlain by coal measures will become producers, as there are some portions of the State in which the coal does not occur in beds of such thickness as to warrant the hope that it can be mined. The mining of coal is widespread, however, for in 1916 there was production from 61 of the 102 counties of the State, There seem to be no cases in which operations will be limited by depth, as none of the coal measures lie at depths much greater than those at which it has been proved that coal may be profitably mined in this field. In fact, the deepest shaft reaching a bed of bituminous coal in the United States is located in this State at Assumption, where coal only 3 ½ ft. (1.07 m.) thick is worked at a depth of 1004 ft. (306 m.). The coal beds occur in the form of a basin which is deepest along a line extending through the central part of the State and bearing a little west of north. The northern, western and southern borders of this basin lie within the boundaries of the State, but on the eastern side the Illinois field is continuous with the Indiana field. The glacial drift covers all except the extreme southern end of the State and the visible outcropping

Jan 1, 1918

By J. N. Ong, J. P. Ratledge, J. H. Boyce

Since German operators opened the Tsumeb mine in the early 1900's, continuous operation has been interrupted only by enforced shutdowns during two world wars and the depression of the 1930's. Original metallurgical practice was blast furnace smelting. This was applicable only to low zinc ore, leaving large tonnages of high zinc ore to be stockpiled on the surface. A gravity concentrator using tables, buddles, and jigs operated for several years, but differential flotation of the ore did not get beyond the experimental stage. When the property was put up for sale by the South African Custodian of Enemy Property there was an estimated 434,000 tons of ore on surface dumps. The dump material, assaying 4.48 pct Cu, 15.8 pct Pb, and 10.9 pct Zn, had become highly oxidized during a stay of many years on the surface. But these dump ores had to be used in evaluating possible metallurgy because the shaft became flooded after the 1940 shutdown and underground ore was unavailable. Many companies examined Tsumeb but quickly lost enthusiasm because of the formidable metallurgical problems presented by the dump ore. However, on the basis of extensive test work, the present company decided that differential flotation would be successful and purchased the property after competitive bidding.

Jan 4, 1955

By J. Hunter

DuXing 1942, Louisiana attained the rank of fourth among the great oil-producing states of this country. Its present prominent position is the result of an orderly and systematic program of exploitation with emphasis on conservation. Even before the functioning of M-68, the Federal spacing order, development and production in Louisiana were regulated by various acts of legislation, the most recent of which and by far the most effective is Act 157 of 1940. Under the authority of this act, it has been possible for the Department of Conservation to hold many public hearings and thereby to secure data and evidence regarding the feasibility of issuing rules and regulations for development of various oil and gas fields in the state. As a result of information compiled at such public hearings, many orders have been issued by the Commissioner of Conservation that have in most cases provided reasonable solutions to the problems that arise in the exploitation and development of fields in this state. Probably one of the most effective powers granted the Commissioner of Conservation in the state of Louisiana has been the authority to provide for fieldwide unitiza-tion and pooling of condensate fields. This has led to the erection of huge cycling plants in Louisiana, which permit the most efficient recovery of the liquid content of the reservoirs, and further conserve most of the gas reserve that undoubtedly will be of considerable future value. Many months have passed since various orders of the Department of Conservation were put into effect, and all are accomplishing their purpose; namely, the elimination of waste. Although the effectiveness of these orders provides considerable satisfaction to the members of the Department of Conservation, it is also a tribute to the members of the oil and gas industry in Louisiana, who, in addition to providing carefully prepared technical data, have also given unstinting cooperation and have thereby enabled the Department to cope intelligently with the many problems. Production On Dec. 31, 1942, oil and/or gas was being produced in 50 parishes, or 78 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 12 produced oil, and 5 produced solely gas. This is indeed an enviable record for any state. However, it is reasonable to assume that eventually all parishes in the state of Louisiana will be productive. From a geological viewpoint, there is no apparent reason to assume otherwise—a point that a11 operators seeking oil and gas production in this state may well bear in mind. Twenty new fields were found during 1942—a rate of discovery that does not compare favorably with the 30 new fields found during 1941. The record of discoveries in Louisiana during 1942 is further disappointing when it is realized that 8 of the 20 new fields discovered were gas fields. During this period of war emergency, there are, of course, many

Jan 1, 1943

By J. Hunter

DuXing 1942, Louisiana attained the rank of fourth among the great oil-producing states of this country. Its present prominent position is the result of an orderly and systematic program of exploitation with emphasis on conservation. Even before the functioning of M-68, the Federal spacing order, development and production in Louisiana were regulated by various acts of legislation, the most recent of which and by far the most effective is Act 157 of 1940. Under the authority of this act, it has been possible for the Department of Conservation to hold many public hearings and thereby to secure data and evidence regarding the feasibility of issuing rules and regulations for development of various oil and gas fields in the state. As a result of information compiled at such public hearings, many orders have been issued by the Commissioner of Conservation that have in most cases provided reasonable solutions to the problems that arise in the exploitation and development of fields in this state. Probably one of the most effective powers granted the Commissioner of Conservation in the state of Louisiana has been the authority to provide for fieldwide unitiza-tion and pooling of condensate fields. This has led to the erection of huge cycling plants in Louisiana, which permit the most efficient recovery of the liquid content of the reservoirs, and further conserve most of the gas reserve that undoubtedly will be of considerable future value. Many months have passed since various orders of the Department of Conservation were put into effect, and all are accomplishing their purpose; namely, the elimination of waste. Although the effectiveness of these orders provides considerable satisfaction to the members of the Department of Conservation, it is also a tribute to the members of the oil and gas industry in Louisiana, who, in addition to providing carefully prepared technical data, have also given unstinting cooperation and have thereby enabled the Department to cope intelligently with the many problems. Production On Dec. 31, 1942, oil and/or gas was being produced in 50 parishes, or 78 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 12 produced oil, and 5 produced solely gas. This is indeed an enviable record for any state. However, it is reasonable to assume that eventually all parishes in the state of Louisiana will be productive. From a geological viewpoint, there is no apparent reason to assume otherwise—a point that a11 operators seeking oil and gas production in this state may well bear in mind. Twenty new fields were found during 1942—a rate of discovery that does not compare favorably with the 30 new fields found during 1941. The record of discoveries in Louisiana during 1942 is further disappointing when it is realized that 8 of the 20 new fields discovered were gas fields. During this period of war emergency, there are, of course, many

Jan 1, 1943

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By I. Iwasaki, P. L. De Bruyn

Electrical double-layer properties of the silver sulfide-solution interface in different electrolytes and the influence the properties exert on the adsorption of dodecylammonium acetate (DAA) were studied using an electrochemical titration technique. The flotation behavior of silver sulfide was observed using DAA as collector and the results were correlated with adsorption measurements. Silver and sulfide ions were identified as the potential determining ions and their adsorption densities were measured as functions of the pAg and of the ionic strength at two different pH values. The point-of-zero-charge (PZC) was observed to be at pAg 10.2, the value being independent of pH and of the nature and concentration of the electrolyte used. The surface charge of silver sulfide in these electrolytes was positive for pAg values less than 10.2 and was negative for pAg values greater than 10.2. The adsorption of amine on silver sulfide surfaces at pH 4.7 was found to be strongly dependent on the pAg. A shift in the PZC towards a lower pAg due to the adsorption of amine indicated a specific affinity of dodecylammonium ion towards silver sulfide surfaces. At pH 9.2 a strong adsorption of the undissociated amine molecule was indicated. The PZC shift towards a higher pAg and the adsorption of the amine was virtually independent of the interfacial electrical conditions.

Jan 1, 1972

By Parke A. Dickey, R. Fettke

Drilling activity during 1944 increased considerably in the oil fields and slightly in the shallow gas fields of western Pennsylvania. The number of deep tests (middle Devonian or deeper) completed during 1944 was the same as in 1943 and did not result in discoveries of additional reserves of natural gas or oil. Thus far no commercial oil production has been obtained from sands below the Upper Devonian in Pennsylvania. As a result of the lack of new discoveries, oil production in nearly all of the producing areas in the entire Pennsylvania grade region declined 10 to 11 per cent. Stocks of Pennsylvania Oil The Peilnsylvania grade crude-oil stocks in storage on January 1943 were 2,479,000 bbl. In January 1944 crude stocks totaled 1,846,000 bbl., and during 1944 the stocks of Pennsylvania grade crude declined to a year-ending balance of 1,617,000 bbl. Nearly all of this oil is "unavailable for use," representing pipe-line fill, tank bottoms and limited working inventories at the refineries. The storage of Pennsylvania oil has declined to a point where little or no available crude oil is currently in storage. Prices The posted price of Pennsylvania oil remained constant during 1944; however, on Rug. I, 1944, the wartime Government subsidy was instituted at a rate of 75¢ per barrel. The average price in the Bradford area, including the subsidy, was $3.31 per barrel. New Technical Developments The Pennsylvania Grade Crude Oil Association started a rather ambitious program of research in production fundamentals and technology during 1944. Several well-qualified engineers have been employed and a laboratory is to be equipped at Bradford. The group will investigate, in cooperation with the American Petroleum Institute, the possibilities of bacteria as agents in oil recovery, and undertake other studies of both a fundamental and an applied nature. In cooperation with the Pennsylvania State College, the Research Group worked out a method of measuring water-intake rates in different strata. The method involves injecting salt water down a string of tubing and fresh water down the annulus, determining the location of the interface electrically, and measuring the input rates above and below the interface. The United States Bureau of Mines, in cooperation with oil companies of the Venango district, developed a simple gas-lift tubing string, which is operating successfully in some 20 wells. This device uses the air-gas mixture produced with the oil to lift it by the usual gas-lift principles. The Northern Ordnance Co. is experimenting with a chamber lift device that expels the oil in an unbroken column. These devices hold considerable promise

Jan 1, 1945

By Walter A. Backofen, Donald H. Avery

Intense primary and cross-slip traces were observed in easy glide on Cu: 6 pct-A1 single crystals deformed in tension. A mechanism of cooperative source operation is developed which recognizes that both the applied stress and that resolved from dislocation arrays contribute to the stress on a source. By considering the stress from arrays, the activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals are explained. Furthermore the cross-slip system is predicted to be second favored during easy glide for a large range of orientations. FROM many studies of easy glide in fcc metal crystals, a pattern of observations has developed which still requires full explanation. In pure copper, aluminum, and silver, the easy-glide, slip traces are fine and uniform with steps 50 to 100A on the primary* system.1-4 Yet it has not been at all clear why slip in the pure materials should occur in this way. On the contrary, one might expect, with simple slip and a low hardening rate, that the weakest sources on the primary system would operate extensively to produce strong slip traces. In a brass, however, intense slip steps up to 0.5 are found on both primary and cross-slip system4,6-9 seeger10 has pointed out that in a material of low stacking-fault energy such as a brass, extensive easy-glide cross-slip could not be thermally activated, but rather must originate on the cross-slip plane. In further explanation, the wilsdorfs4 and seeger10 noted that only the cross-slip system would not harden differently than the primary, whatever the latent hardening tendencies of other systems; therefore, in brass, which exhibits high latent hardening, the cross-slip is the only secondary system which could be expected to operate extensively, once it became active. The explanation of how the cross-slip system, on which the applied stress is low, becomes activated has been related, in a nonspecific way, to pileups by Hirsch11 and Honeycombe.l2 In the work to be described, deformation traces on solid-solution Cu: 6 pct A1 single crvstals were studied with conventional light microscopy and a mechanism proposed to explain both the observed activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals. EXPERIMENTAL In preparing the Cu-A1 single crystals, rectangular bars approximately 0.4 in. by 0.4 in. by 6 in. were first machined from ingots made by vacuum melting copper of 99.999 pct and aluminum of 99.99 pct purity. They were then packed in powdered graphite and the crystals grown in a modified Bridgman apparatus at a rate of 5 mm per hr under an atmosphere of purified nitrogen. Crystal perfection as indicated by Laue back-reflection spots was good except for the last inch to freeze, which was discarded. Orientations so determined are shown in Fig. 1. Tensile specimens with a reduced gage section were obtained by masking the ends with electrical tape and chemically polishing in a solution of 20 pct HNO3, 24 pct HAc, 52 pct H3PO4, 2 pct Hcl, and 2 pct H20 at room temperature.13 Finally, the specimens were electropolished in a 30 pct ortho-phosphoric acid bath at 12 v. Tensile deformation was performed in an Instron testing machine at a strain rate of approximately 1 pct per min. During easy glide, extensive cross-slip was observed with all crystals, in spite of the low Schmid factor on this system, and in no case was any other secondary trace encountered. A certain sequence of slip-line development was associated with the extension. At yielding, intense primary traces passing completely through the crystal developed at some point on the gage section, generally near the grips; weak cross-slip traces also appeared, extending from the primary traces into the adjacent undeformed crystal, Fig. 2. Further extension led to primary traces adjacent to the first-formed and connecting with those of the cross-

Jan 1, 1963

By G. Venturello, C. Antonione, G. Della Gatta

Results from work on the effect of inferstitials on recovery and recrystallization of' very pure iron (99.995 pet) doped with nilrogen up to 400 ppm are reported. Nitrided specimens were obtained by heating the iron in a static atmosphere of NH3 + H2. The samples were cold-rolled 80 pet, subjected to a series of isochronal and isothermal anneals, and submitted to examination by X-rays, micrographs, and hardness tests. Small additions of nitrogen show a strong effect in reducing recovery of' the mechanical properties of high-purity iron. At the temperatures of. the experiments, this effect proved greater than in the case of carbon. At 400°C pure iron recovers more than 50 pet of the total hardness increase, carburized iron vecovers 25 pet, and nitrided iron only 10 pet. On the other hand. the addition of nitrogen has, similarly to carbon, a very small effect on recrystallization; the effect is, however, slightly higher than that of carbon. When the concentration Of nitrogen is above the solubility limit in a iron at the temperattue of the experiments, an increase in the frequency of nu -cleation is also observed. THE object of the present work is to improve knowledge on the effect of interstitials both on recovery and on primary recrystallization of pure iron. In fact. at present there are no available data on the effect of nitrogen on high-purity iron. The only work which at present can be somewhat related to this problem is a work of Leak et al.1 in which grain boundary internal friction at high temperature in the presence of increasing amounts of nitrogen is studied by a torsion pendulum. The present work is a continuation of a previous one2 on the effects of carbon. EXPERIMENTAL PART Preparation of the Material. Pure iron was prepared following the same methods used in the pre- vious work2 and was nitrided using controlled quantities of ammonia in an apparatus similar to that used for carburizing. The apparatus consists essentially of a gas-tight quartz tube containing the specimens. The tube, maintained at constant pressure by means of a mercury seal, is placed in a resistance furnace. For nitriding, the NH3 + H2 atmosphere with a suitable concentration of NH3 was introduced into the tube, which had been previously carefully evacuated and degassed by heating at 600°C. The hydrogen used was carefully purified by passing it through a palladium filter. The ammonia required was prepared with the following reaction: CaO + 2NH4CI —CaCl2 + H2O + 2NH3 by heating the mixture of CaO and NH4C1 in a glass flask and then collecting the ammonia in a graduated Hempel burette. For each nitriding program a given amount of NH3 prepared by this method was introduced together with the H2 into the tube previously evacuated. Nitriding of the sample was then performed at 570°C for 48 hr. After this, to ensure a homogeneous distribution of nitrogen, the samples were further heated for 72 hr at 800°C. With this method which uses a static nitriding atmosphere, carefully controlled conditions of purity are obtained. Contrarily, with the conventional continuous-flow methods, using large quantities of circulating gas, there is a greater risk of introducing impurities into the samples. Furthermore, the required nitrogen concentration in the specimen is easily predetermined and obtained. A plot of the relation observed between the initial concentration of NH3 in the gas and the quantity of nitrogen introduced into the iron samples is given in Fig. 1. The data refer to samples of 1.2-mm thickness and to the nitriding conditions previously described. Furthermore, as a comparison, the data relative to two 0.5-mm-thick samples are reported. The presence of a reservoir in the cold zone of the reaction bulb made possible the gradual dissociation of ammonia on the sample in the hot zone. Internal-friction methods were used to determine the content of nitrogen dissolved in the iron samples. Some analyses were also carried out with chemical methods. The following table, Table I, shows a comparison of data obtained with chemical and internal-friction methods. The correspondence between chemical methods and internal-friction

Jan 1, 1964

By J. Ellzey Hayden

THE Cliffs Shaft mine of the Cleveland Cliffs Iron Co., located in the city of Ishpeming, Mich., is the largest producer of hard hematite ore on the Marquette iron range. The two shafts, A and B, lying 820 ft. (250 m.) apart on the east-west trend of the ore formation, were sunk in the early eighties, and, except for four years, have been steady producers of iron ore. Their location, on a hill overlooking the general offices of the company on the one side and the city of Ishpeming on the other, has made the shaft houses landmarks. In the spring of 1919, as the old wooden shaft houses had become shaky and out of line, and would soon be unsafe, it was necessary to replace them with the least possible delay. Three plans of construction were, therefore, considered: To replace the old shaft houses by somewhat similar structures made of wood; to use steel and radically change the design; or to build reinforced-concrete shaft houses outside of the wooden structures, completely enclosing them. The first plan was disapproved, because it is anticipated that the mine will have a long life and the proximity of other buildings makes the danger from fire rather great. Delay in receiving material, and the necessity for closing the shafts during erection, were other factors in the situation. The second plan was disapproved on account of the high cost of steel, slow delivery, and interference with hoisting during the period of erection. The presence near one of the shafts of a large bed of hard gravel suitable for concrete made, the cost of the third plan considerably less than the second, and little, if any, delay in hoisting was expected. Our expectations in this regard' were fully realized. Furthermore, the work could be done by unskilled labor, which was plentiful, and the erection could be quickly started. When the proposition was submitted to Mr. W. G. Mather, president of the company, he recommended that, on account of the prominence of the buildings due to their location, an effort should be made to combine in the design as far as practicable something of architectural beauty. Following his recommendation, the original plans were submitted to the

Jan 8, 1920