Search Documents

By H. Hance James

SOME of the outstanding features of petroleum production in Illinois during 1923 were: (1) Sustained production from the older wells, due to cleaning and deepening; (2) good results from new drilling in a few localities; (3) large percentage of dry holes, many of which were ill advised tests, with a resulting high cost of the new production; (4) decrease in the number of productive wells in the state; (5) low average price of crude petroleum, a serious factor over the entire country. FIG. 1.-ANNUAL TOTALS OF ILLINOIS PRODUCTION. The total production of Illinois for 1923 was 8,710,000 bbl.,1 a decrease of 7.2 per cent. from that of 1922. Of this amount, it is estimated that about 8,500,000 bbl. were produced by old wells, many of which had been cleaned and deepened somewhat, and approximately 210,000 bbl. were obtained from the new wells drilled during the year. About 95 per cent. of the oil comes from the southeastern field in Clark, Crawford, and Lawrence Counties, where production is almost entirely from Pennsylvanian and Mississippian rocks. Extensions of the productive area were made in Clark, Wabash, Marion, and Jackson Counties. Some important gas development has been accomplished near Jacksonville, in Morgan County, and at Gillespie, in Macoupin County.

Jan 3, 1924

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders 9. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1923

By Paul Queneau

Some years from now, perusal of the unfolding saga of the nickel family will show that the year 1968 was the herald of change-both in the geography of its endeavors and in its technology. No one should doubt any longer that oxide ores of nickel have come of lusty age-their heavyweight stature in the Caribbean area and in the Western Pacific can be shrunk only by immersion in the politics of unhappiness. The sulfide branch of the family has been augmented afar off by substantial ore deposits in western Australia-right across the globe from Sudbury-and in southern Africa, 9000 miles from the nickel hub. The Foreword of the 1961 AIME volume, dealing with the extractive metallurgy of copper and nickel, noted that "the dead hands of nitrogen" had been lifted from oxidation reactions utilizing air and that the industry was on the threshold of under- standing this fact. Here, at least, nonferrous industry had led its ferrous counterpart in the commercial use of tonnage oxygen in liquid phase pyrometallurgy-the reference is to oxygen flash smelting. Today large oxygen-producing plants are blossoming everywhere and the fruits which will follow are many and varied. Among them is Inco's forthcoming use of the top-blown oxygen converter for sulfide melts. The bell tolls for those "pyro- metallurgical dinosaurs" which still stalk smelter aisles the world around. Silicate oxide nickel ores will rejoice in the glow of modern elevated temperature chemical metallurgy in its various manifestations, vindicating the bulldog spirit of that ancient of clans, the hot metal men-including the renovator of Le Nickel's Doniambo Works.

Jan 10, 1968

By Robert Mehl

THE Widmanstätten figures found in the steels have been long recog-nized and in some aspects carefully studied,1 especially as they occur in cast hypoeutectoid alloys. Aside.from the practical importance of the structures obtained in the steels by various heat treatments, a study of the characteristics of these figures is interesting because of the rich opportunity the system affords, to, obtain new data on the mechanism of segregation from solid solutions. This opportunity is twofold: first, by changing composition within the austenite range the proeutectoid precipitate may be changed from that of ferrite to that of cementite, thus offering the same opportunity for changing the type of precipitate while maintaining the same basic lattice as that afforded by the Cu-Zn alloys;2 and second, the eutectoid inversion leads upon drastic quenching to the formation of martensite, a Widman-stätten figure of unique interest from ;the crystallographic viewpoint, particularly in comparison with those formed on-slow cooling.3 We have, therefore, two types of structure to study: that formed on slow cooling of hypoeutectoid and hypereutectoid alloys, and that formed on quenching hypoeutectoid, eutectoid, and hypereutectoid alloys. For each of these types of structure we require the crystallographic plane in the mother austenite along which the precipitate forms (we shall see that the precipitates in these alloys are invariably platelike in form), and also the orientation of the precipitate upon this plane. Some of these

Jan 1, 1933

By Robert Goodrich

EXPERIMENTS ON A PORPHYRY COPPER ORE FROM BISBEE, ARIZ. THIS research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward F. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. PETROGRAPHIC DESCRIPTION Texture: Variable. Fine to medium mixed aggregate. Original structure: Obscure. Secondary structure: Fractured; healed.

Jan 8, 1915

The Climax design is for the human being and his needs. Climax President Arthur Bunker has likened the high mountain operation to a giant, 250 million tons in weight, and 12 thousand feet high. No matter how huge or complicated the plant, the design must assure efficient operation by its human operators. By the same token, living and playing facilities must be designed for fullest satisfaction in use-else the capital investment is not justified. Even the product, molybdenum, finds its application through the ever growing demands of a highly industrialized society of humans. Research in Climax Laboratories, in tune with our technical age, helps guide molybdenum to its maximum use for society.

Aug 1, 1955

By W. S. Ayres

The construction of a new breaker at the Cranberry Colliery, Hazleton, Pa., was forced upon the operators, A. Pnrdee & Co., by a fire which destroyed the entire plant early in January, 1896. The loss included, in addition to the breaker, three boilerhouses and three engine-houses. The boilers were not injured, but the steam-pipes and connections were all broken and warped by the fire. The boilers were probably saved from injury by the presence of mind of the fireman., who started all his feed-pumps and filled the boilers with water. The hoisting-engines were more or less warped and cracked, but by patching and replacing the injured and broken parts, they were made to do satisfactory service in the new plant. It may be worthy of mention that the wrought-iron shaft of one of the hoisting-drums, 12 inches in diameter by 17 feet long, was so heated in the fire that the weight of the drum caused it

Jan 1, 1899

Jan 4, 1953

By Eugene S. Machlin

A classical theory of solid solutions involving neavest-nergkbor intevactions with both central and linked-central forces between atoms has been developed. It has been found that the theory, where it can be checked quantitatively, is in ageement with experiment. The theory encompasses a description of many diverse pkenomena, such as antiphase shift structures, size effect, relative stabilities of various solutions, lattice para,neters, and order-disorder transitions. In particulav. a quantitative prediction not involving adjustable pavameters is made concevning the deviation of the Au-Cu interatonlic distance in long-range ordered (Ll,) Cu-Au I fronl the average distance based on the distances in pure gold and copper. This prediction, which is in agreement with expel-intent, has not been encompassed by any preuious theory. The theory of order-disorder is fragmentary. That is, no one theory exists that can explain the variety of qualitative phenomena observed. Further, many theories are not in good quantitative agreement with experiment. This subject has been reviewed by Muto and Takagi, Tuttman, and Oriani.3 There exists no doubt that the quasi-chemical approximation is not a complete description and that the inclusion of strain energy using macroscopic elasticity theory concepts leads to results in disagreement with experimenL4 The observation of antiphase domains and ordering systems such as Cu-Pt has led to Brillouin zone treat-ment of the order-disorder transition as opposed to the classical Ising model. The objective of this paper is to demonstrate that it is possible to develop a pairwise approximation model that can explain many of the observed order-disorder phenomena that have puzzled investigators in the past. This theory is based upon an empirical model due to ergmman' for the elastic constants of metals. This model is generalized for multicomponent systems. As will be shown, the theory yields a short-range ordering energy for the disordered solution which differs from the ordering energy calculated from the differences in energy of disordered and long-range ordered solutions. It will be demonstrated that there is no necessary correlation between heats of formation and the tendency to order or between size effect and the tendency to order. Also, the existence of antiphase domains and iso-short-range-order systems that form superlattices (Cu-Pt) is predicted on the basis of the theory. Further, the relative stability of competing superlattices is calculable from the theory. If single-crystal elastic-moduli data are available for the pure components and one superlattice then there exists but one adjustable parameter in the calculation of lattice parameters for both the disordered and ordered solid solutions. In one special case, no adjustable parameters are required and a quantitative prediction is made. For the calculation of energies and partial order, there exists but one additional adjustable parameter, the pair-exchange energy V used in the quasi-chemical approximation (or the Ising model.) However, in these calculations, much more precise values are required for the single-crystal elastic moduli than available if the quantitative uncertainties in the predicted values of the energies are to be sufficiently small. THEORY ~er~man' has developed a model with which he was able to obtain fair agreement with experiment for the relations between the elastic constants for metals. This model which we shall call Bergman's model is a linear combination of his models I and 11. In effect, Bergman, in this model, considers that each interatomic distortion is composed of two components: a classical central force distortion with an associated central force constant and what we shall call a linked-central force distortion with an associated linked central-force constant. The linked-central force distortion component obeys the constraint that the sum of such distortions over all the bonds equals zero. No constraint is imposed on the classical central force distortion component. Bergman' derives the constraint on the linked-central force distortion on the basis of application of Pauling's relation between bond distortion and bond number to metals.ga This assumption is not logically necessary, however, and the Bergman model may be taken as a mathematical model for elastic constants, e.g., a purely empirical model without a physical basis. In the present work, the method of Bergman has been applied to two-component systems (solid solutions). In place of an external strain—which would allow a calculation of the elastic constants for the two-component system—it is considered that internal interatomic distortions exist as a consequence of having three potentially unequal distortion-free interatomic distances and but one "average" interatomic distance. It is assumed that the distortion-free interatomic distances between atoms of the same element are those found in the pure element having the same undistorted crystal structure as the solid solution. The distortion-free interatomic distance between unlike atoms is in general not measurable except in the probably nonexistent

Jan 1, 1967

By B. L. Seegmiller

Horizontally stratified lithologies of certain open pit or strip mines create unique stability problems for mine operations. Such problems may result when specific lithologies, such as sandstone and shale, exist in final or long-term slopes. Slope instabilities may occur when a sandstone unit directly overlies a shale unit and ground water drains into the mine along the lithologic contact. In essence, the ground water erodes the underlying shales and undercuts the sandstone. Large sandstone blocks fail in a toppling mode and cause safety and cleanup problems. Use of rock reinforcement including chain link fencing, roof bolt mats, rock bolts, rock anchors, and shotcrete offers a possible solution to the problem.

Jan 1, 1985

By H. S. Price, R. L. Reed, J. E. Warren

The behavior of the reverse-combustion process in a linear adiabatic system is theoretically investigated by means of an idealized physical model. T his model is described by a pair of non-linear equations involving heat and mass transfer which are coupled by a concentration-dependent reaction-rate function of the Ar-rhenius type. The differential equations governing the quasi steady-state temperature and concentration distributions are approximately solved by using either physical or mathematical simplifications. It is shown that the reverse -combustion process can be mechanistically described by simple physical models whose behavior equations can be solved formally. It is further demonstrated that the derived reverse-combustion equations can be solved numerically within the error limits for the experimental data. The theoretically predicted peak temperature-flux-velocity relationship exhibits reasonable agreement with experimental data obtained from Athabasca tar sand. The principal contribution of this work lies in its usefulness as a starting point for developing a more comprehensive theory. A description of the vaporization-coking process must be obtained; then, the theory must be extended to three dimensions to include geometrical effects and heat losses. INTRODUCTION In another paper,'" he physical processes visualized as occurring during reverse combustion have been described. In this paper, the extent to which an elementary theory can account for experimental observations is determined. Theoretical results that can be used to estimate some of the behavior characteristics of importance to this process are also presented. Since it is not possible to include all the features of the combustion mechanism of which we are currently aware, the mathematical formulation refers to the highly idealized system developed herein. This simplified physical model is based on the simultaneous transfer of mass and heat accompanied by a chemical reaction: it is described mathematically by a pair of coupled, nonlinear differential equations. Similar sets of equations have been studied extensively in the field of flame propagation; an excellent review of these investigations has been published by Evans.1 FORMULATION OF THE PROBLEM It will be recalled that the experiments are performed with a thin-walled cylindrical tube that is uniformly packed with sand and oil. The system is maintained substantially adiabatic by means of heat supplied externally in such a way that the radial temperature gradient in any plane normal to the axis of the tube approaches zero. Initially, the tube is at ambient temperature, except at one end where it is rapidly heated to a predetermined temperature. When the prescribed temperature is achieved, air is caused to flow into the cold end of the tube. As the oxygen in the air stream contacts the hot oil, a localized exothermic reaction takes place. The generated heat is conducted and convected away from the reaction zone so that definite temperature and concentration profiles are rapidly established and move uniformly in a direction opposite to that of the air flow (Fig. 1). As a consequence of this mode of oxidation, all of the oxygen in the air is consumed; then, the remaining nitrogen and the gaseous combustion products sweep out all vaporized hydrocarbons and leave an immobile hydrocarbon-coke on the sand.

Jan 1, 1933

By D. D. Pollock

The resistivity, temperature coefficient of resistance, and absolute thermoelectric properties of some binary terminal solid solutions of silver were determined. Equations are given which permit the calculation of these properties. CONSIDERABLE work has been done on the constitution and electrical conductivity of binary alloys of silver.1-l2 Some of these alloy studies are apparently complicated by doubtful chemical analyses. In some cases the limits of solid solubility are questionable. Those references which present electrical properties of binary silver alloys usually give just one particular set of characteristics such as conductivity (or resistivity). As a means of checking and extending this earlier work, an investigation was undertaken to describe and calculate the resistivity, temperature coefficient of resistance, and thermoelectric power of binary terminal solid solutions of silver. PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pet (by weight) of impurities. These materials were carefully weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony systems were melted in Al2O3 crucibles, under a boric anhydride cover, and poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles, and they were also covered with boric anhydride and poured into split graphite finger molds. The alloys containing magnesium and manganese

Jan 1, 1964

By S. W. Farnum

ABOUT three years ago at a coal mining institute meeting, it was predicted that mechanical load-ing underground would progress faster than either the electric coal-cutting machines or electric loco-motives had in previous years. This prediction has proved correct so far. In 1925 over 6,000,000 tons of,coal was loaded mechanically underground in the United States and it is estimated that the 1926 tonnage will reach 10,000,000. The use of electric mining machines and locomotives .has prepared the way for quick results. Most coal mines are now equipped with electric power and have a competent staff who understands its use. In spite of this advantage the introduction of the loading machines brings many new problems. Im-proved and concentrated transportation; doing the drilling, shooting, tracklaying and face timbering with company men instead of the former tonnage men; doing the work on the new basis in an economical and efficient manner; altering or modifying mining systems where necessary to further improve the work and reduce oper-ating costs; improving the percentage of lump coal and reducing the slack content where desirable; improving the cleaning of the coal and obtaining a more dependable .and uniform output are a few of the problems that must be met. Each of the different types of loaders now on the market has its particular advantages and disadvantages for a given mining condition. Even with the same mining conditions one type will work well under one ;system of handling, whereas another may favor another system or mining method.

Jan 5, 1927

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

By G. G. Waddell, T. J. Crocker, S. S. M. Chan

A successful engineering structural design often depends upon a thorough understanding of the material properties of the structure. It is no exception when designing a supporting system for stable underground openings. For this reason, studies were made in the deep mines of the Coeur d'Alene mining district to obtain engineering properties of rocks and rock masses immediately surrounding underground openings. In this paper, data concerning laboratory tested physical properties of rocks and in-situ deformation behavior of rock masses from the Galena, Lucky Friday, and Silver Summit mines of the district are presented. Interpretations of the data so obtained and suggestions for the use of the results of the investigations as design criteria are also outlined.

Jan 1, 1973

By Charles A. Mitke

The Copper Queen mine is composed of seven divisions which are operated through the following shafts: The workings of the different shafts are connected by motor-haulage drifts on the even numbered levels. The general location of the ore-bodies and workings is illustrated by the vertical projection of orebodies of the district as shown in Fig. 1. The Uncle Sam, Southwest, and Czar workings have many connections to the surface through raises and extensive cracks that were caused by moving ground. These divisions are cool and are ventilated entirely by natural means. The Holbrook is ventilated partly by natural and partly by artificial ventilation, while the Spray, Gardner, Lowell, and Sacramento are ventilated entirely by mechanical means. In some of the divisions mentioned above a considerable quantity of air exhausts through shafts of adjoining properties.

Jan 1, 1916

By Herbert Clark Hoover, Lou Henry Hoover

QUESTIONS as to the methods of smelting ores and of obtaining metals I discussed in Book IX. Following this, I should explain in what manner the precious metals are parted from the base metals, or on the other hand the base metals from the precious'. Frequently two metals, occasionally more than two, are melted out of one ore, because in nature generally there is some amount of gold in silver and in copper, and some silver in gold, copper, lead, and iron ; likewise some copper in gold, silver, lead, id iron, and some lead in silver ; and lastly, some iron in copper2. But I will begin with gold. Gold is parted from silver, or likewise the latter from the former, whether it be mixed by nature or by art, by means of aqua valens3, and by powders which consist of almost the same things as this aqua. In order to preserve the sequence, I will first speak of the ingredients of which this aqua is made, then of the method of making it, then of the manner in which gold is parted from silver or silver from gold. Almost all these ingredients contain vitriol or alum, which, by themselves, but much more when joined with saltpetre, are powerful to part silver from gold. As to the other things that are added to them, they cannot individually by their own strength and nature separate those metals, but joined they are very powerful. Since there are many combinations, I will set out a few. In the first, the use of which is common and general, there is one libra of vitriol and as much salt, added to a third of a libra of spring water. The second contains two librae of vitriol, one of salt-petre, and as much spring or river water by weight as will pass away whilst the vitriol is being reduced to powder by the fire. The third consists of four librae of vitriol, two and a half librae of saltpetre, half a libra of alum, and one and a half librae of spring water. The fourth consists of two librae of vitriol, as many librae of saltpetre, one quarter of a libra of alum, and three-quarters of a Mbra of spring water. The fifth is composed of one libra of saltpetre,

Jan 1, 1950

By Henry M. Howe, Joseph Winlock, Francis B. Foley

This investigation was undertaken for the purpose of determining, in a systematic way, the effect of the rate of cooling of steels, heated to above the transformation range, on their various mechanical properties. This paper gives the results obtained in the investigation of the heat treatment of carbon steels carried out under the auspices of the Committee on The Heat Treatment of Carbon Steels of the Engineering Division, National Research Council. The objects of this committee, of which Dr. Henry M. Howe was chairman, were to increase knowledge of the influence of heat treatment on the mechanical properties of carbon steel. The mcthod pursued was to subject specimens of steel of the carbon contents most used for engineering work, 0.34 per cent., 0.52 per cent., and 0.75 per cent., to various heat treatments, and to test the mechanical properties thus induced. The steels were the same as were used by the committee on fatigue phenomena. This project was financed jointly by the U. S. Bureaus of Mines and Standards; industries and university laboratories have cooperated. A large part of the work was done at Doctor Howe's private laboratory. The committee consisted of F. B. Foley, H. AT. Boylston, H. C. Boynton, G. K. Burgess, H. J. French, J. H. Hall, Zay Jeffries, R. S. Johnston, F. C. Langenberg, H. F. Moore, E. H. Yeirce, H. S. Rawdon, W. E. Ruder and 11. J. Stagg. The work was undertaken at the suggestion of Doctor Howe, who thought, at the outset, that steel in the sorbitic state might have properties which, for most engineering purposes, would be better than those of the usual or pearlitic state. By a systematic variation in the heating

Jan 1, 1923

By Joseph Winlock, Francis B. Foley, Henry M. Howe

This investigation was undertaken for the purpose of determining, in a systematic way, the effect of the rate of cooling of steels, heated to above the transformation range, on their various mechanical properties. This paper gives the results obtained in the investigation of the heat treatment of carbon steels carried out under the auspices of the Committee on The Heat Treatment of Carbon Steels of the Engineering Division, National Research Council. The objects of this committee, of which Dr. Henry M. Howe was chairman, were to increase knowledge of the influence of heat treatment on the mechanical properties of carbon steel. The mcthod pursued was to subject specimens of steel of the carbon contents most used for engineering work, 0.34 per cent., 0.52 per cent., and 0.75 per cent., to various heat treatments, and to test the mechanical properties thus induced. The steels were the same as were used by the committee on fatigue phenomena. This project was financed jointly by the U. S. Bureaus of Mines and Standards; industries and university laboratories have cooperated. A large part of the work was done at Doctor Howe's private laboratory. The committee consisted of F. B. Foley, H. AT. Boylston, H. C. Boynton, G. K. Burgess, H. J. French, J. H. Hall, Zay Jeffries, R. S. Johnston, F. C. Langenberg, H. F. Moore, E. H. Yeirce, H. S. Rawdon, W. E. Ruder and 11. J. Stagg. The work was undertaken at the suggestion of Doctor Howe, who thought, at the outset, that steel in the sorbitic state might have properties which, for most engineering purposes, would be better than those of the usual or pearlitic state. By a systematic variation in the heating

Jan 1, 1923