Search Documents

By William Victor Vietti

A METHOD of determining the average density of the fluid column in a flowing oil well is presented. Actual field data from several wells are used to illustrate the application of the method in the Yates Field, Pecos County, Texas. The depth of the wells in the Yates Field varies from 900 to 1700 ft. depending on surface elevation and the location of the wells on structure. Production rates over 8000 bbl. hourly have been determined and many

Jan 1, 1930

"NAME…""Utah"" is derived from the name of the Indian tribe, variously spelled ""Yuta, “Ute"" ""Youta,"" ""Uta,"" ""Eutaw,"" and finally ""Utah."" It means ""in the tops of the mountains,"" or ""on the heights."" The state emblem is the ""Beehive,"" typical of industry. State nickname is ""Beehive State.""AREA…Utah is the tenth state in area. It contains 84,990 square miles, of which 2,806 miles are water. When admitted as a territory in 1850, Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.TOPOGRAPHY…Utah is generally mountainous, with several main ranges and also detached groups of mountains. The valleys are broad and level. The mean altitude of the state is 6,100 feet above sea level, which makes the state the third highest of the Union. The highest point in Utah is King's Peak (13,498) in the Uinta range. The lowest point is Beaverdam Creek (2,000) in Washington county.CLIMATE…The climate is diversified between mild temperate in the northern portion to semitropical in the southern portion. There are four distinct seasons. Snowfall is heavy at the greater altitudes and rare in the southern portion. Rainfall is moderate throughout the state. Extremes of heat and cold are unusual."

Jan 1, 1925

By Stanly A. Easton

SEVEN years ago there was installed in the hospital of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho, an ultra-violet ray quartz lamp, the standard equipment which is found everywhere in the offices of physicians and among usual hospital equipment. The use of this lamp was con- fined largely to treatment of pathological cases, still treatment of under-nourished children, run-down anemic people, both men and women, and, as a general tonic, was part of the routine hospital procedure. At the latitude of the Ceur d'Alene district and especially because of the position of the towns in deep canyons, with much overcast and cloudy weather, sunshine is not plentiful at any time of the year; for many of the winter months there is scarcely any. Underground workers, particularly during the winter, have little sun- shine; it is not unusual to have none at all for weeks at a time. Treatment by the ultra-violet ray lamp in the hospital has resulted in many extraordinary benefits but the use of the lamp is expensive and limited. Some weeks ago attention was directed to the automatic solarium equipment of the Burdick Corporation. The doctors strongly recommended the increased use of the ultra-violet lamp for its curative powers and tonic effects, urging that it be made accessible to all employees. Real interest was . . also displayed by employees with the possibility of securing ultra-violet ray treatment for themselves and families under better conditions than it was possible to have by the limited use of the lamp at the hospital. This resulted in the installation of the so-called sun room or automatic solarium as an adjunct to the mine change-house. An annex was built to the change-house, with dressing rooms for women, children and men from other departments, and the outfit put into use on Sept. 5, 1929. The installation consists of an escalator, or

Jan 1, 1929

By Edward Estabrook

THE Salt Creek oil field in Natrona County, Wyo., is the largest pool that has been found in the Rocky Mountain region and one of the largest in the United States. Many features of its production records are of peculiar interest, because of the unusual slowness with which it has been developed. This paper is published by the permission of the Midwest Refining Co., whose records have been freely drawn upon. Many mem¬bers of the Midwest organization have assisted in the collection of the material, but Messrs. F. E. Wood and L. E. Smith have been particularly helpful. The Salt Creek oil field is situated on a great dome with a closure of about 1500 ft., which rises at the northern end of a long anticline extending north-northwest by south-southeast for fully 25 miles. The productive area includes parts of townships 39 and 40 north and ranges 78 and 79 west of the sixth principal meridian. The Teapot oil field occupies a minor dome at about the center of the same anticline and adjoins the Salt Creek oil field on the southeast. The Teapot Naval Reserve includes the Teapot Dome and about 760 acres of the Salt Creek dome. In this paper, the Salt Creek oil field will be considered as' including all of the dome, except that part which lies within the Teapot Naval Reserve and the area west of the dome where oil is produced from shale crevices.

Jan 9, 1925

By C. W. Pollock

THAT a distressing explosion of some magnitude did not take place in the Berry No. 3 mine of the Ford Collieries Co. recently was solely because no source of ignition was present when the stage was set for such an occurrence. The mines of this company, which are in West Deer Township, Allegheny' County, Pa., have been operating in the double or thick Freeport seam since 1.909. During this entire period they have been classed as gaseous by the Pennsylvania Department of Mines, and some gas has been encountered from time to time almost entirely however in development work in the vicinity of clay veins or wants-and never to my knowledge on gobs or in rib work.

Jan 1, 1935

By John S. Crandall

Occurrence: small crystals in alluvial sands from the eroding Belt Series mica schists. Flowsheet: dragline, trommel screen, jigs, drier, crusher, screens. Value: ground, $2.50 per cu yd, garnet sand gross $60. per ton. Costs: production and sales $48. per ton. Uses: blasting sand in aircraft plants, monumental works, foundries. Efficiency comparison: superior to silica sand. Future: possibilities only touched upon, research continuing.

Jan 1, 1950

By G. F. LOUCHLIN

A FEATURE of the International Geological Congress to be held at Pretoria, South Africa, in the summer of 1929,. will be a symposium on the gold resources of the world. In this connection the U. S. Geological Survey and Bureau of Mines have been asked to prepare a report, showing production in the United States, describing the geology of its principal gold- producing districts, and estimating reserves (a) assuming a continuation of presen6economic conditions, and (b) assuming lower costs. This report will not be completed before April 1, but data thus far assembled are here presented with the hope of profiting by discussion and by information from those well informed on any of the important gold-producing districts. Gold production in the United States rose to a maximum exceeding $100,000,000 in 1915 and then rapidly declined to about $52,000,000 in 1920. Since then it has fluctuated, but on the whole slightly declined. Reviews of the eight leading states afford the following tentative conclusions :

Jan 1, 1929

By AIME AIME

REGISTRATION and licensing of engineers is now being given consideration by a special committee of the Institute, authorized at the March meeting of the Board of Directors. The subject is one that has recently been or is now actively before engineering organizations in many of the States of the Union. In Washington, D. C., the Washington Society of Engineers and the local sections of ten national engineering societies, including the A.I.M.E., recently had a joint committee investigate the subject: this committee formulating a proposed law that has been presented to Washington engineers for their consideration. At the same time, the committee has summarized the reasons for and against registration of engineers in Washington, D. C. As many of these reasons are of more than local application, they are here reprinted so that all members of the A.I.M.E. may be informed on the subject. It is expected that some report of the Institute's Committee on Registration, State Councils and Professional Development will he made at some forthcoming meeting of the Board of Directors.

Jan 1, 1932

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to over-produce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metal-based economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening. The metal age started many centuries ago, and with the exception of the noble metals, barely a dent was made in world reserves until the present century. Then, as a result of the pioneering ideas of D. C. Jackling and Paul Gemmel, and the willingness of the McNeals, Penroses and Guggenheims to back ideas with money, a virtual explosion of metal production was propagated throughout the world. It is important to examine the causes of this expansion to determine whether it is a trend that may be sustained or whether it is anomalous and therefore attributable to circumstances not likely to be repeated or continued. This period of plenty is a once only phenomenon. Vast metal resources have been sitting around here for eons, while the world was unaware of or unconcerned with their existence. But when population began to grow exponentially, and ways were discovered to use metals to develop machines to do the work of men and animals, the exploitation of raw materials increased at a staggering rate. And now the realization is dawning that minerals are a wasting asset and are beginning to present supply problems that should begin to be of concern. Two main factors have caused this condition; One is the population growth, and the other is the expanding demand for irreplaceable raw materials as nations become more developed. A group of systems analysts, at Massachusetts Institute of Technology in a book Limits of Growth, has warned that at present rates of population growth and resource consumption together with environmental constraints, a point will be reached within 100 years when the world population will become totally incapable of supporting itself. The authors conclude that this end result could be avoided if a planned equilibrium could be established at a lower rate of population growth and resource consumption. Fortunately, there is evidence that the population problem is moderating. The growth rate in the U.S. has decreased from 2.3% per year in 1900 to 1.1% in 1970. But, even at the lower rate, population will double in 70 years. The world rate is greater, and if it continues, world population will rise from 3.5 billion to nearly 10 billion in 50 years. All of these projections are questionable because the dangers of growing population are now being recognized. A marked decrease in growth rate has been noted in the more developed countries-in fact, it was zero in the U.S. in 1972. The other factor affecting consumption of raw materials is the increase in per capita use of most items as individuals become more affluent. Many economists believe that developing countries such as China and India represent a vast future potential market; but there are others, with whom the author agrees, who believe over-population tends to stagnate development. Nevertheless, it is a fact that vigorously developing societies increase consumption at a rate far above their population growth rate.

Jan 1, 1974

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By AIME AIME

ORGANIZATION of The Federated American Engineering Societies was effected at the organizing conference of national, local, state and regional engineering and allied technical organizations at the Cosmos Club, Washington, D. C., June 3 and 4. Thus is brought into being the greatest national engineering society in the world. The object of the organization is to further the interests of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to engineering and allied technical professions. Prominent engineers from all parts of the country, representing more than 75 engineering societies, with an aggregate membership of more than 125,000, participated in the organization. The constitution as adopted by the conference, calls for the creation of s managing body to be known as the American Engineering Council, and its executive board. The belief was expressed that the entire organization would come to be spoken of as the American Engineering Council. The council is to coordinate the activities of state councils and of local affiliations whenever these activities are of national or general importance or may affect the general interests of engineers. Representation in the council is to be according to membership of the component societies.

Jan 1, 1920

By Fred C., Bond

IN CYANIDE milling, little attention has been paid to the effect of the viscosity of the mill solution on the extraction speed. The viscosity of the solution varies with the amount of dissolved salts present as impurities. These salts build up to a maximum depending on the character of the ore, the grade of cyanide used, the lime and salts added, and the impurities originally in the water. The viscosity will change from month to month and week to week as these factors vary; and that this variation affects the extraction is unquestioned, although methods for calculating it are lacking. The character of the ore is probably the most important of the four factors, as the amount of minerals present that are soluble in cyanide solution will vary constantly, and each variation affects the viscosity of the mill solution. When the cyanide consumption increases as the character of the ore changes, the viscosity of the solution will increase and the extraction will decrease, for the cyanide consumption is usually a measure of the impurities dissolved from the ore. In other words, as the difference between the total and free cyanide increases the extraction will decrease, other factors remaining constant.

Jan 1, 1926

By T. Egleston

The Boston and Colorado Smelting Works are situated in the town of Black Hawk, Gilpin County, Colorado, on the Clear Creek Narrow Gauge Railway, 55 miles from Denver, in the Rocky Mountains, at an altitude of 7800 feet. It was one of the first works erected for the metallurgical treatment of gold ores, and the only one established in Colorado on a large scale which has been uniformly successful. Both gold and silver ores are treated, and gold, silver, and copper produced. The lead is not separated from the ores nor paid for, if it exists, and is entirely lost in the residues. The works were planned and built by Professor Hill, formerly Professor of Chemistry in Brown University, Providence, R. I., and is still managed by him, assisted by Mr. Richard Pearce, formerly professor in the School of Mines at Truro, England. They are very advantageously situated with regard to the ore-producing regions, having Boulder County on the north, which produces, besides ordinary gold ores, a series of tellurium minerals, such as altaite, sylvanite, and hessite, which are very rich in gold and silver. They are associated with copper and iron pyrites, blende, galena, and the carbonate and oxides of iron. Gilpin County itself produces for the most part the pyrites of iron and copper rich in gold, with a small quantity of galena and blende, which is rich in silver. In

By W. M. Myers

MINERAL Economics is the most recent profession to be recognized as a separate division of the mineral industries. It has originated from the increasing awareness of the importance of the economic aspects of industries concerned with discovery, extraction, and utilization of minerals. It is concerned with the interrelated fields of economics and technology. The individual trained in economics alone cannot qualify. The curriculum in the School of Mineral Industries at The Pennsylvania State College was approved in May 1946, and enrollment begun in September of that year. Due to the transfer of advanced students from other courses, particularly metallurgy and electrical engineering, it was possible to graduate the first seniors in June 1947. The next class was graduated in February 1948. From experience derived from placing these graduates in industry, and from information supplied by prospective employers, valuable data have been obtained in the organization and operation of the course of study.

Jan 1, 1948

By T. PH. D. Egleston

THE Boston and Colorado Smelting Works are situated in the town of Black Hawk, Gilpin County, Colorado, on the Clear Creek Narrow Gauge Railway, 55 miles from Denver, in the Rocky Mountains, at an altitude of 7800 feet. It was one of the first works erected for the metallurgical treatment of gold ores, and the only one established in Colorado on a large scale which has been uniformly successful. Both gold and silver ores are treated, and gold, silver, and copper produced. The lead is not separated from the ores nor paid for, if it exists, and is entirely lost in the residues. The works were planned and built by Professor Hill, formerly Professor of Chemistry in Brown University, Providence, R. I., and is still managed by him, assisted by Mr. Richard Pearce, formerly professor in the School of Mines at Truro, England. They are very advantageously situated with regard to the ore-producing regions, having Boulder County on the north, which produces, besides ordinary gold ores, a series of tellurium minerals, such as altaite, sylvanite, and hessite, which are very rich in gold and silver. They are associated with copper and iron pyrites, blende, galena, and the carbonate and oxides of iron. Gilpin County itself produces for the most part the pyrites of iron and copper rich in gold, with a small quantity of galena and blende, which is rich in silver. In * By consent of the council of the Institute, this paper was first published in London Engineering, from which the engravings are here reproduced.

Jan 1, 1876

By James B. Cathcart

The potash mine of the International Minerals and Chemical Corp. is about 18 miles east of Carlsbad, New Mexico, in sec 1 and 12, T 22 S, R 29 E, N.M.P.M. Potash is produced from two zones in the Salado formation of late Permian age. The lower zone, consisting of a mixture of sylvite (KCl) and halite (NaCl), lies at a depth of about 900 ft, and the upper zone, in which the principal potassium mineral is langbeinite (K2S04.2MgS0d), lies at a depth of about 800 ft. Because of the plastic nature of the material, fractures in the Salado formation are extremely rare and have been noted only on the 800 ft level of the International mine. The open fracture described below is almost unique. Only one other open fracture has been noted, and it was on a working face in the same general area as the one described, but was destroyed before the writer had a chance to examine it. According to J. E. Tong, foreman on the 800 level, this fracture was similar to, but smaller than, the one herein described.

Jan 1, 1949

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and refineries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Carlsbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies.

Jan 1, 1949

By R. B. Moore

IN 1914 the writer and K. L. Kithil announced, through Bulletin 70 of the U. S. Bureau of Mines, that the United States possessed the largest deposits of radium-bearing ore in the world. At that time a small amount of this ore was being, mined and shipped to Europe, and one company was preparing to start the extraction and recovery of radium in this country. The importance of our carnotite deposits in Colorado and Utah up to the publication of Bulletin 70 was not, however, appreciated by anyone.. At that time the total supply of radium in the world was about 10 g., calculated as element, and when I estimated that at least 100 g. of radium element, and probably 200 g., would be produced from our carnotite deposits, there was a considerable amount of skepticism. Up to the present time almost 200 g. have come from this ore, and some writers put this figure a little higher. Uranium ore was found in the copper mines of the Union Minière du Haut-Katanga at Luiswishi in 1913. Later discoveries were made at other places in the Belgian Congo, and the Katanga ores now represent the largest supply of radium-bearing ore in the world. In fact, since 1923 very little radium has been produced from American carnotite, the Katanga ore representing practically the world's supply of. radium since that date.

Jan 1, 1930

By AIME AIME

THE second session on geophysical prospecting at the February meeting of the Institute was a discussion of the mining law and the bearing of the new method of search on location of claims and assessment work thereon. Allen H. Rogers was chairman of the meeting, which he opened by reviewing the present law and the proposed changes. W. R. Ingalls commented (by letter) on the Arentz bill, as introduced into the House of Representatives in 1921 and the need for revision of the present mining law. L. W. Douglas explained (by letter) the bill that he introduced and which has been passed by the House. SAMUEL S. ARENTZ, Nevada: It is my opinion that if the American Institute of Mining and Metallurgical Engineers is to sell this proposition to the people in the West, they have to sell it to the lawyers, because, after all, they are heard loudly when it comes to speaking in Congress. One man tells the other, "This thing is a vicious piece of legislation"; it might not be, but they will pass it on if it affects them. If the Institute would impress on the people affected that we need a re-codification of the mining law and that such is necessary along certain lines; that things have changed during the past decade or two, so today instead of doing our prospecting alone through the sinking of a shaft, through a discovery that may be seen, we are now moving on to more modern means of discovery through geophysics, through the churn-drill, through geology, through geological inference, I think we could get somewhere.

Jan 1, 1929

By George B. Clark

COMMERCIAL strip mining of coal was first begun in the state of Illinois in 1911.1 The annual tonnage of coal produced from coal strip mines in the state was very small until 1924, when the strip mines shipped 1.68 pet of the total state shipping mine tonnage. Since then, strip mines have gradually come into their own by producing a sizable percentage of the coal produced in the state. Table 1 shows the coal tonnage shipped from both underground and strip coal mines in the state of Illinois for selected years. The table illustrates the major role that strip mines play in the state's coal industry. Today, strip mining is generally conducted in areas where the coal seams lie so close to the surface of earth that a stripping method of mining the coal seam is cheaper than an underground method. Strip mining not only recovers 100 pct of the coal deposit, but may also be used as a method of mining large acreages of coal abandoned by the closing of underground mines.

Jan 1, 1949