Search Documents

By Norman J. Gibbs, John Sroka

INTRODUCTION At the point a company decides to begin mine development and wishes to convince lending institutions that the proposed operation will return their borrowed funds, plus interest, over the terms of the loan, communications between lender and borrower are crucial. The importance of the mine feasibility presentation should not be underplayed, especially as new projects continue to increase in size, complexity, and cost. While the content and emphasis of a report to the lender will vary according to the particular project and type of debt financing sought, there is a general base of information upon which all such studies are built. THE PROJECT'S TECHNICAL ASPECTS Here, the object is to satisfy the lender that he will not be unduly exposed to technical risks as a result of the physical scope of the project. Reserves The feasibility report submitted to financial institutions should include an adequate description of the geologic setting, mineralogy, ore types, and reserves broken down into such recognized categories as proven/probable/possible or measured/indicated/inferred. Rather than a bald statement of reserves, lenders prefer to have detailed information on: History of exploration Drilling, both percussion and core, with core recovery, drill hole spacing, analyses, and continuity of mineralization Bulk sampling, with core assay comparisons Overburden, with stripping ratios Specific methodology of reserve calculation, and Geologic reserves vs. mineable reserves. As a rule of thumb, a lender would prefer to see that reserves in the proven class alone are sufficient to support operations at the design rates until the borrowed funds are repaid. (See also Schreiber above in this Chapter.) Mining The rationale for adoption of a particular mining technique should be presented as well as descriptions and justifications for: Preproduction development Preliminary mine plan, with forecasts of grades and material movements Geotechnical test work which influenced decisions Mining recoveries and efficiencies Major equipment, with type, model, rating life, spares, replacement schedules, utilization, and productivity Manpower requirements and work schedules Design assumptions Ore stockpiling and blending Environmental requirements, and Waste disposal Processing If a new ore body is to be developed or a new process used, it is important to provide details of test work, scale up, and extrapolation factors. A basic process description with a summary of the studies which justify the intended processing route should be included with the following data:

Jan 1, 1985

By John Birkinbine

A retrospect of the growth of the production of pig-iron for the past half century would be the history of the invention and introduction of heated blast as applied to the smelting of iron ores. As the apparatus employed was improved in conception and construction, the economical operation of the furnaces to which it was attached was the more marked, and the production correspondingly increased. To compare the original iron box placed over a coal fire with the modern hot-blast stove, with its combustion-chamber, gas-burners, and air-regulators, would be as unfavorable to the former as to contrast the product of the little Blauöfen with the yield of the improved furnaces of to-day. But, as these little Blauöfen were the germs from which the larger plants have grown, so from the crude apparatus invented and applied by Neilson has grown, in the face of great opposition, the more economical hot-blast stoves now in use. It is not surprising that an innovation like heated blast should have received a large amount of attention from metallurgists, nor that men of recognized ability should formerly have been found both among its champions and opponents, but it is remarkable that, at the present day, with the results of careful research and thorough experiment compiled in convenient shape for perusal, there are ironmasters who still consider it economy to allow the products of combustion to escape into the atmosphere, rather than utilize them in heating the blast, because of a supposed injury to the quality of the product. In the present state of knowledge and practice, it is proper to express as an axiom, that a well-constructed hot-blast apparatus is essential to the economic operation of an iron-producing plant. Of the interpretation of proper construction there is of necessity a variety of opinions, and, with the view of solving the problem, the apparatus for heating blast has from time to time assumed various forms. Boxes, cylinders, and pipes, placed horizontally, vertically, inclined, or in circles and spirals, have been tried; there have been pistol-shaped pipes, double pipes, divided or diaphragm pipes, siphon pipes, and as much variety in the mains, connections, flues, and setting. It is probable that, to the introduction of the bell and hopper in

Book Notices CATALYSIS IN INDUSTRIAL CHEMISTRY. By G. G. Henderson. Lond. and N. Y., Longmans, Green and Co., 1919. 202 pp., cloth, 9 X 6 in., $3.25. This, the latest volume of the series of Monographs on Industrial Chemistry which is being published under the editorship of Sir Edward Thorpe, is intended to present broadly, our present knowledge of the phenomenon of which it treats. The hook reviews the existing literature on catalysis, paying particular attention to the many applications now used in industry. COMMERCIAL OILS-VEGETABLE AND ANIMAL. With special reference to Oriental Oils. By I. F. Laucks. 1st edition. N. Y., John Wiley and Sons, Inc.;, Lond. Chapman and Hall, Ltd., 1919. 138 pp., cloth, 8 X 5 in., $1.25. Intended to give to men in the oil trade, who have not had technical training, the technical data and information required in every-day dealings, in concise form. The various commercial oils are listed, together with their sources, uses, and phys-ical and chemical characteristics. The values have been collected from the standard texts, supplemented, particularly in regard to oriental oils, by the results obtained in the author's laboratory. FIFTY YEARS OF IRON AND STEEL. By Joseph G. Butler, Jr. Cleveland, The Penton Press, 1919. 145 pp., por., 10 X 6 in., leather. (Gift of author.) This volume is one of a special edition, of 100 copies, of an address delivered before the American Iron and Steel Institute in 1917, in which the author gives his personal reminiscences of the development in iron and steel making, as observed during an active participation in the industry in eastern Ohio, which began in 1857. To this are added some brief data on the early history of iron and steel, and a chapter on the activities of the American iron manufactures during the great war. The volume is profusely illustrated with portraits of men of note in the industry.

Jan 12, 1919

By B. Fernow

The question of preserving the forests in this country is an impor tant one, not only to trades using wood but to the whole nation, and though agitated for many years has not received that general consid eration which its broad bearing demands. Those who are interested in and working for reform in the treat ment of American forests are looking to the government for help, suggesting the creation of a commission to study the conditions of forests at home and abroad, and hope that a sound system of manag ing the woodlands will be thereby inaugurated. This reform will cost time and money, all the more because the government can bring to bear upon private owners hardly any power but that of good example and encouragement. There is, however, another aspect of the question to which I wish to draw your attention, namely; the more economical use of the valuable material which our forests offer, a more careful and ex haustive utilization of its constituents in all cases where wood or its products are applied. The wasteful consumption of wood in the United States is in every way so enormous as to justify the statement that by merely adopting an economical husbandry in this particular the destruction of forests might be delayed for many years, while the neglect of this imperatively needed and immediately practicable reform deprives legislative remedies of much of their value. In this regard I wish to draw the attention of metallurgists, especially those who are in terested in the manufacture of charcoal iron, to a more economical and profitable use of wood in iron manufacture. For thousands of years of human history wood was the main, nay, the only material used for fuel. Mineral coal came into use only in the fourteenth century, and it is only recently that it has largely displaced its less carbonaceous predecessor as fuel. The art of concentrating carbon in the form of charcoal for easier transportation and readier use in distant places was, according to Pliny, known to the ancients long before Christ., and was practiced in all countries, especially in connection with the iron-manufacture.

Jan 1, 1879

By B. Fernow

(Read at the Philadelphia Meeting, February, 1878.) THE question of preserving the forests in this country is an important one, not only to trades using wood but to the whole nation, and though agitated for many years has not received that general consideration which its broad bearing demands. Those who are interested in and working for reform in the treatment of American forests are looking to the government for help, suggesting the creation of a commission to study the conditions of forests at home and abroad, and hope that a sound system of managing the woodlands will be thereby inaugurated. This reform will cost time and money, all the more because the government can bring to bear upon private owners hardly any power but that of good example and encouragement. There is, however, another aspect of the question to which I wish to draw your attention, namely; the more economical use of the valuable material which our forests offer, a more careful and exhaustive utilization of its constituents in all cases where wood or its products are applied. The wasteful consumption of wood in the United States is in every way so enormous as to justify the statement that by merely adopting an economical husbandry in this particular the destruction of forests might be delayed for many years, while the neglect of this imperatively needed and immediately practicable reform deprives legislative remedies of much of their value. In this regard I wish to draw the attention of metallurgists, especially those who are interested in the manufacture of charcoal iron, to a more economical and profitable use of wood in iron manufacture. For thousands of years of human history wood was the main, nay, the only material used for fuel. Mineral coal came into use only in the fourteenth century, and it is only recently that it has largely displaced its less carbonaceous predecessor as fuel. The art of concentrating carbon in the form of charcoal for easier transportation and readier use in distant places was, according to Pliny, known to the ancients long before Christ, and was practiced in all countries, especially in connection with the iron- manufacture.

Jan 1, 1878

By Persifor Frazer

A classification of natural objects is usually based either upon some fundamental and permanent attribute of the thing itself (as in the case of scientific classifications), or it embraces one or more generalizations convenient for use in ordinary life. Thus, it suffices for the statistician to know that so many tons of fish are annually taken by our fishermen, and that they realize so many thousands of dollars, whereas to the student of natural history the anatomy, habits, and relationships of the animals are of chief interest, as settling their respective places in the scale of animate nature. Many different classifications of coals have been attempted, as one would naturally anticipate from the immense extent of the coal trade, and the different localities whence the supply was derived. The English divisions were prevalent up to the date of the publication of the last geological survey of the State, except so far as they were modified by local designations. Indeed, Rogers' classifications made very little alteration in the English nomenclature, as may be seen by comparing the tables given below. To commence with the different kinds mentioned in Ure's Dictionary of Arts, Manufactures and Mines of 1845 : " 1. Cubical Coal.—Black, shining, compact, moderately hard and easily frangible. Comes out in rectangular masses, of which the

Jan 1, 1879

By R. B. Woodworth

Discussion of the paper of R. B. Woodworth, presented at the New York meeting, February, 1916, and printed in Bulletin No. 107, November, 1915, pp. 2247 to 2312. R. B. WOODWORTH, Pittsburgh, Pa.-This is a very long paper. It is a structural engineer's contribution to the art of mining and is written from his standpoint rather than from that of the mining engineer, and is, therefore, a study in the development of drilling structures by one who has made it his business to design structures rather than mechanism and machinery and rather than to utilize those structures in the actual exploitation of oil and gas. Drilling practice varies widely in different oil and gas fields. The , problems of western Pennsylvania are much simpler than the problems of the Mid-Continent and of the Gulf Coastal Plain and these again are simpler than problems of the Pacific Coast. The history of the commercial development of oil and gas is recorded in the annual publications of the U. S. Geological Survey and other bodies whose business it is to make record of statistics. The mechanical and structural features of the art of drilling have not yet received adequate treatment by the historian. Scattered references may be found on the subject in almost any work dealing at large with petroleum and its production. These references, however, are to those particular aspects of the matter that were contemporary with the publications themselves, but so far as I am aware there is no continuous and comprehensive account written of the development of drilling structures from their beginnings down to the present time, and certainly the more modern application of steel in the construction of such structures has not previously had an adequate discussion. With this latter phase of the subject I have been intimately associated, indeed, taking to myself the credit for having, in a way, been responsible more than any one else in the United States for the application of steel in the manufacture of drilling structures, and the purpose of the paper which is now before you is to record particularly the steps in that development while the subject is still fresh and the data available.

Jan 5, 1916

By R. M. Zimmerman

INTRODUCTION Tuff is being considered as a possible geologic median for the underground storage of commercial high level radioactive wastes by the Department of Energy (DOE). DOE has the responsibility for developing or improving the technology fir safely and permanently isolating these wastes. DOE programs must satisfy requirements established by the Nuclear Regulatory Commission (NRC) for the licensing and regulating of these storage facilities (NRC 1981). Pertinent draft NRC requirements are: 1) releases of radioactivity to the environment must be within prescribed limits and 2) emplaced canisters containing wastes must be retrievable up to 50 years following emplacement. High level radioactive wastes produce heat in storage and it is essential that the thermal/mechanical/hydrological response of the host rock will not significantly degrade either the structural performance o£ the repository or the ability of the natural or engineered barriers to retard radionuclide migration. The Nevada Nuclear Waste Storage Investigations (NNWSI) was established by DOE to evaluate the suitability of disposing of high level nuclear wastes on or near the Nevada Test Site (NTS) (NNWSI 1980). NNWSI has focused exploration and site evaluation on the tuffs of Yucca Mountain. Field testing is essential to support site characterization and repository design efforts. Preliminary studies have been conducted indicating that tuffs in G-tunnel on the NIS contain welded and nonwelded tuffs that have similar properties to those in Yucca Mountain. Thus, field testing can be accelerated. This paper discusses the issues supporting the planned field experiments in G-tunnel. Issues not related to rock mechanics are not included.

Jan 1, 1982

By William L. Zeller

IN the past 75 years industrial engineering has been highly developed in many fields, but the coal mining industry has just begun to realize its potential for cutting costs. To receive the maximum benefit, a company should apply industrial engineering from the time a new installation is contemplated, but the principles can also be used to reduce and control the costs of an established operation. One company that had been mechanized for seven years reduced its total labor cost 57 pct by industrial engineering. Of this reduction, 20 pct was brought about by a preventive maintenance, rebuilding, and scheduled lubrication program that eliminated 80 pct of the delay caused by mechanical and electrical failures. Thirty percent of the cost reduction was attributed to rearranging the work force into crews of the most effective size, changing working methods, and training all mine supervision in the principles of the cost reduction program. The remaining 7 pct reduction was brought about by a wage incentive program for all the men in the mine. The productivity of this coal mining operation was increased from less than 8 tons per payroll man to 20 tons. This increased productivity was brought about while using the same equipment, men, and supervision.

Jan 12, 1957

By W. A. McCurdy, Joseph W. Leonard, T. S. Spicer

INTRODUCTION by T. S. SPICER and J. W. LEONARD Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is process design, operation and maintenance to produce an acceptable product which can be sold at the greatest possible profit. Because of these interests, attention to the unrealized potential value of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of both the product as well as the tributary coal flow moving through a modem coal preparation plant. Thus, coal types having similar physical and chemical properties tend to become increasingly concentrated according to size, specific gravity and/or surface chemistry. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches which are sandwiched together in layers and which visually differ from each other by physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, six percentage points of dry volatile matter and 10 percentage points of total sulfur.1 Similar wide variations exist for calorific value, seam moisture content and undoubtedly, for any other conceivable coal test parameter which might be used for comparative purposes. These observations all point to the long established fact that coal is not homogeneous as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance. Since both coal and associated minerals entering a preparation plant are highly heterogeneous, a multi-product potential beginning with certain flotation cell concentrates and ending with plant refuse may exist. Such a potential can and to a limited extent is achieved at some operations by drawing off coal according to size, specific gravity and/or surface chemistry differences from individual coal cleaning processes. Such a sequenced draw-off of coal of increasing ash increments could yield, among other products, chemical coals, coking coals, coals for pulverized fuel boilers, cyclone boiler coals, coals for cement plants, limestone, shale and clay. Basis for Coal Evaluation and Selection Despite the known heterogeneity of coal, the final analysis of a given coal product is customarily reported as a single average since coal has always

Jan 1, 1968

By Stephen Taber

JOHN C. BRANNER, Stanford University, Cal. (communication to the Secretary *).-Wideawake teachers of geology are constantly on the lookout for good illustrations of veins, especially where the processes of formation are either clearly shown or suggested. And I long ago found out that one who would learn nature's laws must despise nothing. It thus happened that in 1910, Dr. George J. Peirce of the depart-ment of botany at Stanford University called to my attention a cracked and broken yellow earthenware dish, 8 ½ in. across the top and 2 ½ in. deep, that, to the ordinary observer, seemed to be of no further use, and quite ready for the waste can. The striking thing about this dish was that the thin glaze over much of the outside surface and over the upper margin of the inside surface had been lifted in small scales, varying in. diameter from ½ cm. to 1 cm., and thrust outward and held there by some sort of white fibrous mineral. The process looked very much like one we are familiar with in the Southern States where. we often see in the winter pebbles and soil thrust out from a clay bank or lifted from a clay soil and held there supported by what is popularly known as needle-ice. Upon inquiry I learned the following facts in regard to the history of this particular dish: In the summer of 1910, it had been partly filled with a concentrated salt solution taken from one of the salterns of the Stauffer Chemical Co. at Redwood City, Cal. A qualitative analysis of the original brine showed: Present: iron, magnesium, sodium, potassium, chlorides, sulphates, nitrates (trace), bromides, carbonates, borates (trace), and considerable amounts of organic matter. Absent: calcium, lithium and iodides.

Jan 3, 1917

By John C. Smock

The ten years, 1879 to 1888, inclusive, have been notable in the history of iron-making for the great rise during the latter part of 1879 and the earlier half of 1880; for the maximum of production in 1882 ; for the gradual decline and the reduced product through 1883,1884 and nearly to the end of 1885; then, for the recovery through- 1886 and 1887; and the extraordinary outputs of our iron furnaces during the last three years. The price of pig-iron might be taken as an index to the condition of the iron-mining industry, and if represented graphically, they would shorn approximately parallel curves. The mining industry cannot always respond quickly to a rise in price and an increased demand for ore; nor can its production drop simultaneously with sudden falls in price of iron and of ore. Hence, the irregularities of the one are not reflected in the other. The statistics of the iron mines collected by the United States census, for the year ending June 30, 1880, exhibit admirably their condition at that time. The reports received from mine owners and managers, of the production for the year 1888, furnish the basis for a comparison and supply data for some notes on the changes in the iron-mining industry in New York which have taken place in this period of time. The iron-ores of New York may be grouped in the following districts: I. The Highlands of the Hudson (magnetites). II. The Lake Champlain and Adirondack Region (magnetites). III. St. Lawrence and Jefferson Counties (red hematites). IV. Clinton and Wayne Counties (fossil-ores of the Clinton Group). V. Dutchess and Colnmbia Counties (limonites). VI. The Hudson River (carbonates). VII. Staten Island (limonites). The ores of the first and second districts, as enumerated, are almost exclusively magnetites; those of the third and fourth are hematites;

Jan 1, 1889

By Robert W. Hunt

I have repeatedly said that the mechanical treatment of the metal forming a steel rail, during its manufacture, was comparatively of much greater importance than its chemical composition; and years of observation have confirmed and emphasized this fact. ' The comparison of the wear of the earlier steel rails with that of later ones, and to the great disadvantage of the latter, ia still being constantly made by railway oficials. And while some of us, with experience covering the whole history of the manufacture of steel rails, are aware of the great differences in the conditions governing their production at various periods, I do not think the engineering world generally appreciates the direct and imperative influence which these variations have had, and are having, upon the wearing-quality of the rails. In the earlier days, the steel was poured into ingots which would make but two 30-ft. rails not exceeding a weight of 60 lb. per yard—giving a mass weighing, say about 1,400 lb., and of a section of about 12 in. square. To-day the ingots are about 22 in. square, and weigh more than 4,000 lb. Of course, the interior of the larger ingots must remain hot and liquid longer than that of the smaller ones, and from this condition arises the steel-rail makers béte noire—segregation of the metalloids and piping of the steel. Ingots of the smallest section will pipe, but with the increase of the size, so will follow that of the interior cavity. This well-known tendency demands that special care should be exercised to avoid the evils arising from it.

Jan 1, 1905

The production of petroleum in India (including Burma) increased from 334,811,624 gal.' ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939

The production of petroleum in India (including Burma) increased from 334,811,624 gal.' ill 1936 to 350,322,222 gal. in 1937, the highest figure in the history of the industry. The increase in 1937 was clue to an increase of some 20 million gallons from Singu, 51/2 million gallons from Attack, 11/4 million gallons from Thayetmyo, and 1 mi1lien gallons from Digboi, accompanied by decrcases of 91/2 million gallons from Yenan-gyaung and 2 million gallons from Yenangyat,. The amount of gasoline produced from natural gas during the year was 10,616,313 gal. in Burma and 456,780 gal. in the Punjab. Yenangyaung Field.—The Yenangyaung field maintained its reputation of being one of the most wonderful oil fields in the world. The total production during 1937 was less than in the previous year but the resources of the field as a whole are sufficient to ensure an adequate supply of oil for many years. At the end of 1037 there were 2910 wells producing in the field. Besides a large number of ells drilled to shallow sands, this total includes 180 hand-dug wells, whose continued existenice is one of the interesting features of the field. During the year the deep drilling activities of 1936 in the southern part of the field died down, owing to the disappointing results obtained. On the eastern flank the limit of present economic extension of the oil sands was approximately demareated. Satisfactory results continue to be obtained from gas drives in the leased blocks; gas is also injected for repressuring and storage. Casing policies continue to be carefully designed to protect the oil sands against the danger of flooding by water and, in general, production methods throughout the field are characterized by a realization of the importance of the conservation of oil and gas and the prevention of waste, whether simple or underground. Singu Field.—-In 1937 the increase in the output from the Singu field was continued. This increased production was due not only to the rapid development of the valuable area in the southern part of the field but also to the successful results obtained from the first wells to produce from behind the practically completed river training wall of the Burmah Oil

Jan 1, 1939

By S. E. Bretherton

(San Francisco Meeting, September, 1915) DURING the year 1878-79, Anton Eilers, who was then interested in the lead smelting and refining business near Salt Lake City, Utah, made a somewhat radical departure from the regular practice at that time, which was to use but little lime in the slag, with a high percentage of iron. Lime was not only a cheaper flux than iron, but it enabled the metallurgist to make a more siliceous slag, an economical advantage in smelting where the smelting companies had to purchase either iron or lime to neutralize the excess silica, and penalize the ore shippers accordingly. The larger amount of both lime and silica in the slag also made it of lighter specific gravity, and a better separation of the metals and mattes was secured. This change in the formation of slags for lead smelting was brought about by Anton Eilers, prior to the Leadville mining excitement of 1879. We must also give Mr. Eilers credit for the general introduction of the hollow water-cooled cast-iron jacket for the blast furnace. Again referring to the use of more lime and less iron in the formation of slags,. there is no doubt but that it prevents the formation of a great many so-called "sows" in the lead crucible, such as were made in the early history of lead smelting in the Rocky Mountains; these sows consisted of lead, iron, arsenic, sulphur, copper, and other metals, including gold and silver, mixed with unconsumed fuel, and often, after vain attempts to cut them up or melt them to a suitable size for handling, were buried in the slag clumps to get them out of-sight. Another advantage derived from the adoption of high-lime slags. when smelting ore containing arsenic is the production of less speiss (a by-product heavier than matte, resulting from careless operation of the furnace, the lead being driven out of the crucible and sows built up). This speiss, while usually not as rich in precious metals as matte made at the same time, is too valuable to be thrown away; but it is difficult to treat, and it was thrown away or piled on the slag clumps in the pioneer clays of lead smelting in this country.

Jan 8, 1915

By E. E. Barker

Although flotation was known to be a successful process prior to 1312, Utah Copper Co.'s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.'s ores were on a full flotation basis. Effect of Flotation on Ore Reserves The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Jackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent. became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent. and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

By Charles Kirchhoff

For twenty years it has been my work to watch and record progress in both the technical and the commercial branches of mining engineering in the wide sense in which it is represented by our Institute. While you who have been actively engaged in our profession have made history, a few of us have attempted to be the historians and have been kept keenly on the qui vive to follow the developments of so broad a field. One so employed may be pardoned if he ask you to pause for the unusual purpose of looking backward, that you may measure what you and others have done, and that the younger men may gather inspiration from the work accomplished by their elders and their predecessors. It is not so long since that the commercial management dominated our industries. Bred in the school of science, which seeks its reward in establishing the truth, our engineers were sometimes indifferent to trade conditions and requirements. Much of that feeling has disappeared, and the engineer recognizes that it is his mission to apply the achievements of science to a useful commercial end. On the other hand, business men now understand that the utilization of our natural resources and the production of articles for consumption is impossible without the intervention of the engineer. They must co-operate, unless, indeed, the two functions are combined in one man —a rare but powerful combination. Now the final measure of success of both is the cost sheet on the one hand and the expansion of markets on the other, so closely interwoven, so mutually interdependent. There is one cardinal feature, however, which characterizes the engineer's work—namely, the permanence of his achievements. Every improvement, particularly when it has been recorded in such lasting form as a paper in the Transactions of our societies—

Jan 1, 1900

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

ONE of the interesting-though not unnatural-features of the whole Porphyry Copper development is the way in which the history of each property dovetails with that of one or more of the others. The same names keep cropping up as one digs into the accounts of events from 1900 to 1915. J. Parke Channing made examinations of Nevada, Ray, and Inspiration, as well as of Miami. Henry Krumb did important work in the early stages of the exploitation of Utah, Nevada, Ray, Braden, and Inspiration. Pope Yeatman was favorably impressed with the Braden property before he had ever visited it, when he saw a batch of Braden ore sent to the United States for testing. It reminded him immediately of Nevada Consolidated ore: indeed, he was unwilling at first to believe that it came from South America. And it was while working on the examination at Utah Copper that Philip Wiseman became enthused with the possibilities of the Ray mines. In 1905, Mr. Krumb, under the general direction of A. Chester Beatty, was strenuously engaged at Bingham, Utah, in arriving at an answer to this question: Should or should not the Guggenheim interests back Jackling to the tune of several million dollars to build the big concentrators at Gafield? Seeley W. Mudd was the Guggenheim engineer on the Pacific coast and in that capacity was indirectly responsible for the work at Bingham. At his suggestion Wiseman came up from Los Angeles as one of Krumb's assistants-at $5 per day, incidentally. A little later Mr. Mudd, in Utah on one of his visits, went down to Bingham. That evening in the old Hills Hotel in Markham Gulch he was going over reports with Mr. Krumb. Wiseman and some of the other engineers on Krumb's staff were present. During a breathing spell, Mudd expressed

Jan 1, 1933