Search Documents

By D. H. Henley, F. F. Craig, W. W. Owens

The oil recovery performance of systems producing entirely by bottom-water encroachment has been experimentally determined in a series of scaled laboratory-model tests. The effects of well spacing, fluid mobilities, rate of production, capillary and gravity forces, well penetration and well completion techniques on the oil recovery performance have been investigated. The laboratory tests were performed using two uniform, un-consolidated sand-pack models. The models have ratios of the interwell distance to the formation thickness of 12 and 2, respectively. Tests at constant total fluid production rate were performed simulating a range of uniform reservoir characteristics and operating conditions encountered in field operations. The performance was determined by material balance and by observation of the encroachment of dyed fluids into the models. The results of the model tests agreed with those obtained mathematically when the conditions previously considered in theoretical studies were simulated, that is, when the oil and water are of equal density and no capillary forces exist. The model study of bottom-water drive indicated that certain variables can aoect the oil recovery performance to a greater degree than can be predicted by present analytical methods. In one comparison, the oil recovery at a water-oil ratio of 20 (obtained at a wide well spacing) varied as much as threefold, depending upon the system's properties and the production rate. Lesser effect of mobility ratio and no eflect of capillary forces over the range studied were observed. The test 'results also showed that the deeper the well penetration into the oil column, the greater the total water production to a producing WOR of 20. However, the ultimate sweep efficiency, and so the oil recovery to this level of WOR, did not vary significantly with well penetration. Horizontal fractures at the top of the formation did not significantly change the sweep characteristics of the reservoir models when values of radius and fracture capacity encountered in actual reservoirs were used. Impermeable pancakes at the bottom of the well moderately increased the oil recovery efficiency both at water breakthrough and at high water-oil ratios. A method is outlined by which the oil recovery performance of other uniform bottom-water drive systems can be estimated from the information obtained in these model tests. INTRODUCTION When oil is produced from a well which partially penetrates an oil zone completely underlain by water, the water rises directly beneath the well in a symmetrical cone when the system is uniform. Two different flow mechanisms can cause the water cone to form—coning and bottom-water drive. In coning, the aquifer is relatively inactive and the cone is formed beneath the well by the pressure gradients associated with the oil flow to the well. The oil can be produced by a solution-gas drive, an edge-water drive or other driving forces in the interwell area. In a bottom-water drive, the driving force for oil production comes from an upward encroachment of the underlying active aquifer. Two papers have analyzed the theoretical performance characteristics of bottom-water drive reservoirs. In the initial mathematical investigation, Muskat' established the equations which determine the pressure distribution in this type of reservoir and solved these equations for certain conditions. Specifically, it was assumed that the water and oil had equal mobilities and equal densities, there were no capillary forces, the pressure throughout the oil zone remained above the bubble-point pressure, a constant pressure existed at the initial water-oil contact and the oil was completely displaced by the encroaching water. These assumptions were used in obtaining analytical solutions. In general, Muskat found that the sweep efficiency to initial water breakthrough to the well was larger for the thicker oil zones, the closer well spacings, the lower ratios of vertical to horizontal permeabilities, the smaller the penetration of the well into the oil zone and the smaller the bore size of the well. The production history after water breakthrough was expressed as a volumetric sweep efficiency at a given producing water-oil ratio. The results indicated that cumulative oil production at producing water-oil ratios of 10 is less affected by the well spacing than is the water-free production history. Muskat studied well spacing which today would be regarded as close. The maximum value of his dimensionless well spacing (ratio of interwell distance to formation thickness) was 4.3. This would require the development of a 50-ft-thick oil sand on less than 10-acre spacing if the vertical and horizontal permeabilities were equal, with

By P. J. Shenon

ENROLLMENT in geological and mining engineering curricula is declining at an accelerated rate despite the greatest need for trained men ever extant in the minerals industry. Industrial and military demand is mounting, but the number of freshmen selecting the mineral field continues to fall. Estimates on the needs of industry range as high as 30,000 new engineers a year. The current deficit is more than 60,000 engineers less than the 350,000 to 450,000 which eventually will be needed. The indisputable fact is that the colleges are turning out fewer and fewer engineers despite the greatest enrollment in colleges and universities ever experienced in the United States. In 1950 a record 52,000 young men stepped out of the confines of ivy covered walls with engineering degrees in their hands. By 1951, however, the number dropped to 41,000 and present enrollment indicates a national graduating class of only 25,000 for 1952. No letup in the drop is forecast. About 19,000 can be looked for in 1953 and 1954 may reach an unhappy 12,000. It becomes clear that something must be done to attract high school graduates to engineering. One immediate possibility could be to make the course burden carried by the engineering student somewhat lighter. The prescribed curriculum in many schools is such that the student takes the path of least resistance, and instead of training for an engineering future, studies for a vocation which will allow him to learn and at the same time get at least a nominal enjoyment out of college life. Review geological and mining curricula of 20 colleges and it will be found that the engineering student is a veritable pack mule compared to a lad taking liberal arts or some other non-technical program of study. The curriculum for geological engineering at one school calls for 202 semester hr, with almost 23 hr carried per semester. Multiply this figure by three hr, the minimum supposedly to be devoted to a credit and you get 69 hr per week. With a bare minimum of 84 hr for sleeping and eating, about two hours a day remain for recreation. However, the load of other schools investigated is about 19 hr. The University of Utah requires 238 quarter hr for graduation with a degree in geological engineering, while requiring only 183 quarter hr for baccalaureate degree from University college, Utah's liberal arts school. It can be stated with a measure of surety that the same proportions exist in other universities. The first step would be for ECPD to review its requirements for mining and geological engineering. It must recognize that mining and geological engineers operate in a specialized field, as do other types of engineers. Although a geological engineer may not design a bridge, as pictured by the ECPD Committee on Engineering Schools, his field of design calls for similar engineering precision, a knowledge of materials, construction methods, economic considerations, and financing. Six schools have been accredited by the ECPD. What is the basis for approval and can the requirements be modified and still be kept in line with the needs of the geological engineer? Course work from school to school varies with the exception of mathematics, chemistry, and physics. Even in those courses the not inconsiderable variation lends dubious creditability to the mean. One accredited school requires 7 1/3 semester hr of chemistry, compared with 24 hr required by another, making an average for the six schools of 17 1 /3 hr. Required credit hr in mechanics ranges from 4 to 18 and in surveying from 2 to 15. Several non-accredited schools require more hr than do the accredited schools in some courses. Why is the engineering student forced to carry such a back-breaking load? The answer is of course fairly obvious. He is irrevocably set apart from the rest of the student body because of the nature of his life's work. He is training for a place in a world where technology is becoming increasingly involved. He must be prepared to do a job now-and not later. Mining and geological engineering require the same essential backgrounds as other engineers, and more. The "more" is a knowledge of mining methods, metallurgy and geology for the mining engineer. The geological engineer must know in addition, mineralogy, petrography, and geophysics. The load is compounded finally by the addition of liberal arts courses. Should anything be done to relieve the situation? Today's engineer must be a whole man, capable of handling the tools of communication and with an understanding of the economics of industry. He must be able to write clear simple English, and he must be man who can think from some other position than bent over a work table. He must be aware of the history of his country and to some extent that of the world. Not all schools share this view. Only two of the accredited schools require history courses. However, five of the non-accredited schools make it mandatory. Four accredited and five of the nonaccredited schools require economics. Courses in mathematics, physics, and chemistry are fundamental in engineer training. The average for the accredited schools could serve as a guide in

Jan 1, 1952

By S. G. Cupschalk, J. J. Wert, R. A. Buchanan

The uniaxial deformation of thermally ordered and disordered polycrystalline Cu3Pt was studied by means of the X-ray line - broadening analysis according to Warren and Averbach and the extension of this analysis to ordered fcc materials by Mikkola and Cohen. Because of the heat treatment history, extinction had a pronounced effect on the X-ray spectra of ordered and disordered C%Pt at small plastic strains. After an appropriate correction for extinction, the long-range order in thermally ordered ChPt was found to decrease at a slow constant rate with plastic strain. Furthermore, the antiphase domain probability increased at a constant rate to 17.5 pct strain. The effective particle size behavior indicated that the stacking fault energy is lower in ordered than in disordered Cu3Pt. Analysis of the stress-strain curves shouled that ordered Cuzt has a slightly lower yield Point but a much higher work-hardening rate than disordered Cu3Pt. THE presence of long-range order in a solid-solution alloy has a marked effect on its mechanical properties. While this effect has been known qualitatively for many years, it was not until recently that detailed investigations have been performed to determine the exact role long-range order plays in this strengthening mechanism. The development of an advanced, quantitative. X-ray diffraction analysis by Warren and Averbachl and the extension of this analysis to the L1, type super lattice by Mikkola and cohen2 have greatly accelerated research in this field. The research reported in this paper consisted of two primary phases. The first phase was to determine the effect of long-range order on the tensile properties of polycrystalline Cu3Pt. This objective was accomplished by comparing the stress-strain behavior of thermally ordered CusPt to that of thermally disordered CusPt. The second phase of the research was to determine the difference between the atomic arrangements in thermally ordered and thermally disordered Cu3Pt as a function of uniaxial deformation and thereby gain a deeper insight into the mechanism by which long-range order affects the tensile properties. This second objective was accomplished by applying the Warren-Averbach method of peak profile analysis to the X-ray diffraction patterns obtained from ordered and disordered Cu3Pt after given amounts of uniaxial deformation. EXPERIMENTAL PROCEDURE The Cu3Pt was prepared by vacuum melting and casting. After a homogenization anneal, the ingot was cold-rolled to sheet form. Two tensile specimens with gage sections of 2.50 by 0.500 by 0.115 in. were carefully machined from the sheet. The specimens were polished with a final step of 600-grit paper to insure smooth diffracting surfaces. Finally, one specimen was heat-treated to yield an average grain diameter of 0.016 mm and an initial degree of long-range order, S, of 0.825. The other specimen was water-quenched from above the critical temperature, 645"C, to yield an average grain diameter of 0.017 mm and zero long-range order. The heat treatment history of each specimen is shown in Table I. The tensile tests were performed utilizing a Research Incorporated Model 900.95 Materials Testing System. This unit employs a closed-loop feedback system which maintains a constant strain rate through an extensometer clipped to the gage section of the tensile specimen. A strain rate of 1.32 i0.02 x 10"4 sec-' was employed in testing both specimens. In the X-ray diffraction analysis, a General Electric XRD-5 diffractometer equipped with a pulse-height analyzer set for 90 pct efficiency was employed. The goniometer speed selected was 0.2 deg, 20, per min. Filtered Cu radiation was used for all peaks and all peaks were chart-recorded. Because of nonuni-form grain size. it was necessary to spin the specimens during X-ray analysis in order to obtain reproducible integrated intensities. The spinning rate was 2000 i100 rpm. The application of the Warren-Averbach method of peak broadening analysis to a diffraction pattern is very time consuming if done manually. In this research, the calculations involved were performed with the aid of a computer program by wagner.3 As reported by Wagner, the program is written in Fortran TV computer language. It was modified to Fortran I1 so as to be handled by the IBM 7072 computer at Van-derbilt University. In the X-ray diffraction analysis of uniaxially deformed Cu3Pt, the 100, 200. 400. 111, and 222 reflections were recorded from the initially ordered sample after 'plastic strains of 3.0, 6.0, 9.0, 12.0,

Jan 1, 1970

By W. R. Ingalls

In reviewing the history of the metallurgy of zinc, I shall pass hastily over what is only of antiquarian interest. That has been excellently treated by Dr. Bernhard Neumann in "Die Metalle" (1904) and has been described briefly in my "Production and Properties of Zinc" (1902), in my "Lead and Zinc in the United States " (1908), and in other metallurgical works of more or less the same date. In this present monograph, I have it in mind to confine myself mainly to technical practice, especially to that of the last 75 years, prior to which period advance was slow and of no great moment. The ancients made brass by the cementation process, i.e., embedding copper in a mixture of calamine and carbon and heating, whereby zinc oxide was reduced and zinc was vaporized and combined with the copper. Zinc was isolated by some of the alchemists, who named it and knew something of its properties, but made no use of it. Long before then, however, zinc was produced in India. Later it was produced in southern China. Possibly the Chinese obtained their knowledge from India. The Chinese in remote places still produce small quantities of zinc. I have seen photographs of their furnaces; or pots, for they hardly deserve the dignity of being called furnaces. I imagine that they are the same that were used centuries ago, for I cannot conceive of anything more primitive. Anyway, it is certain that the idea of a commercial production of zinc in Europe was imported from the Orient, where the metal was known in commerce as Speauter and Spiauter, whence speltrum and finally our term spelter. Tutanego and Tuteneague are other old names. Dr. Isaac Lawson went to China about 1730, expressly to discover the method of its production. What connection there was between Isaac Lawson and John Champion we do not know, but the latter obtained in 1739 a patent for a process of distillation downward and at some time between 1740 and 1743 erected a works at Bristol and actually began the manufacture of spelter. A production of 200 tons per annum is mentioned. In about the year 1766, Rishop Watson visited the Champion works and saw the process in operation, which previously had been

Jan 1, 1937

William P. Blake, TUCSON, Ariz. (communication to the Secretary): As one who in youth, now nearly half a century ago, had the privilege of participating in the initial explorations which have alreacly resulted, within a single lifetime, in the establishment and Development of a vast continental empire, so well described by Dr. Douglas, I may be permitted to supplement with some additional details the comprehensive sketch given in his paper. Before the War Department, in 1853, sent out the Pacific railroad exploring parties, Fremont had already made his memorable expeditions, exploring the Great Basin and the passes into California; Sitgreaves had traversed, from east to west, the Zuni and Moqui country; and, still later, Emory had examined the region along the boundary-line between the United States and Mexico. The services of these pioneers deserve to be mentioned in even an outline of the history of continental development. Concerning the five practicable railroad-routes, suggested in the Reports of Explorations aid Surveys," etc., as published

Jan 1, 1900

By C. S. Smith, K. K. Ikeuye

In an earlier paper1 one of the authors called attention to the significance of the relative free energies of grain boundaries and interphase boundaries in alloys in determining the shape and distribution of micro-constituents. The ratio of the interphase and inter-crystalline boundary energies (that is, —?12, where ?12 is the energy of the interface between a crystal of phase 1 and a crystal of phase 2, and ?11 is the energy of the boundary between two crystals of phase 1) will be denoted by F. It is this ratio that determines, by the simple triangle of forces relation, the dihedral angle, ?, of phase 2 where it adjoins a boundary between two grains of phase 1. On a metallographic sample various angles are actually obtained because of the random orientation of the plane of observation, but the statistically most frequent angle is the true one. These basic principles were discussed in detail in the earlier paper. The experiments described below show the effect of both composition and temperature on ? and T for some alloys containing a liquid phase, and provide data on the rate of approach to the equilibrium angles in both solid and liquid phases. All the alloys were melted in a graphite crucible and cast into ingots 3/4 by 11/8 in. cross-section. Some of the aluminum alloys consisted of two immiscible liquids from which uniform castings could not be obtained. The amount of liquid phase varied locally to a considerable extent and the analyses were meaningless. Nevertheless, the composition of the liquid would not differ from that in an alloy of the intended gross composition, and the synthetic composition of the alloys was therefore used in considering the surface energy results. The ingots were given initial deformation by cold-rolling to 50 pct reduction, annealed, and given a second 50 pct reduction prior to cutting into small samples for heat treatment at the times and temperatures subsequently reported. The resulting micro-samples were carefully prepared metallographically and examined at magnifications of 650, 1280, or 2500. The objectives used were 21X, 0.40 NA (dry); 41X, 0.65 NA (dry); and 80X, 1.40 NA (oil emulsion). The appropriate angles were measured by rotation of the stage of a Bausch and Lomb metallograph to align the appropriate boundaries successively with a cross-hair in a micrometer eyepiece. About 250 angles were measured on each phase. Though the angles were read to 1°, the accuracy is probably not above 3°, because of uncertainty in setting the cross-hair tangent to the sometimes curved boundary. The corners of very small particles, particularly in early stages of adjustment after cold-rolling, were difficult to measure and the results were slightly dependent on the magnification used (compare Fig 1-C and 1-D). With particles of larger size and more nearly equilibrium shape, magnification made no difference (vide Fig 1-F and 1-G). The measured angles were grouped in 10° intervals (5° if ? was less than 20°) and plotted in bar

Jan 1, 1950

By P. L. De Bruyn, R. J. Charles

THE transfer of kinetic energy of translation into other forms of energy by impact is a fundamental process in most crushing and grinding operations. During and after the impact process the original source energy may be accounted for in any of the following possible forms: 1) Kinetic energy of translation of both the impacted and impacting objects. 2) Kinetic energy of vibration of the components of the impact system. 3) Potential energy as strain energy of the components of the system or in the form of residual stresses. 4) Heat generated by internal friction during plastic deformation or during damping of elastic waves. 5) New surface energy of fractured materials. At any instant during the impact process only the strain energy of the components of the system can contribute directly to the brittle fracture process. If fracture is the desired result, as in comminution, it would seem advantageous to choose or arrange the conditions of impact so that a maximum amount of the original kinetic energy could be converted to strain energy at some moment during a single impact. The present work deals with determination of these desirable conditions for a simple case of impact and application of the principles involved to general cases of impact. Experimental Method: Longitudinal impact of a rod with a fixed end was chosen as the impact system for investigation. The rod was mounted horizontally and the fixed end was formed by butting one end of the rod against a rigidly mounted steel anvil. The rod, of pyrex glass, was 10 in. long by 1 in. diam with both ends rounded to a 6 in. radius. The rounded ends permitted reproducible impacts on the free end of the rod and assured a symmetrical fixed end. Pyrex was selected as the rod material because of the marked elastic properties of such glass and the similarity of fracture between pyrex and many materials encountered in crushing and grinding operations. The frequency of natural longitudinal oscillation of the rod was 10 kc, and thus simple electronic equipment could be used for observation of strain changes occurring in the rod at this frequency. As shown in Fig. 1, impacts on the free end of the rod were obtained either by a pendulum device or by a spring-loaded gun. Relatively heavy hammers (100 to 600 g) of mild steel were used in the pendu- lum impacts, while fairly light projectiles (20 to 80 g) were fired from the spring-loaded gun. One of the main objects of the experimental work was to obtain the strain-time history of the rod as a function of the mass and kinetic energy of the impacting hammers. For this purpose a technique involving wire resistance strain gages and a recording oscilloscope was employed. Five gages were applied at equidistant sections along the rod, and by means of a switching arrangement the strain-time history at any section, and for any impact, could be obtained in the form of an oscillograph with a time base. The equation relating strain and voltage change across a strain gage through which a constant current is flowing is as follows: e = ?v/iRF [1] ? = strain, ?v = voltage change, i = gage current, R = gage resistance, and F = gage factor (from manufacturer's data — SRA type, Baldwin Lima Corp.). With the above equation an oscillograph depicting voltage change vs time on a single trace can be converted directly to a strain-time diagram if a calibration of the vertical response on the oscilloscope screen for specific voltage inputs is available. In the present case the calibration was obtained by photographing precisely known audio frequency voltages on the same oscillograph as that on which a voltage-time trace from a strain gage had been made. Synchronization of the beginning of the single trace with the beginning of the impact was accomplished by permitting contact of the impacting objects to close an electrical circuit from which a voltage pulse, sufficient to initiate the trace, was obtained. The struck end of the rod was lightly silvered for purposes of electrical conduction so that it would form one of the electrical contacts. Markers every 100 micro-seconds on the traces served for a time base calibration. Determinations of the kinetic energies of translation prior to impact were made in the case of the pendulum hammers by measuring the height of fall of the hammer and in the case of the projectiles by measuring the exit velocity from the gun barrel by means of an electrical circuit employing light sources, slits, and phototubes.' During the experimental work it became evident that the time of contact between the impacting object and the rod was an important variable in the impact process. Measurements of the times of contact were made, therefore, for every impact for which a strain-time record was obtained. The time of contact was determined by permitting the impacting components, when in contact, to act as a closed switch and discharge a condenser at relatively constant voltage. The discharge was observed and photographed with a time base on the oscilloscope screen.

Jan 1, 1957

By B. S. Gottfried

A generalized mathematical model is presented, which describes the thermal recovery of oil in linear systems with convective external heat loss. Three-phase fluid flow, conduction-convection heat transfer, chemical reaction between oxygen and oil and aqueous phase change are included, making the model applicable to a variety of thermal recovery processes. The complexity of the model requires that numerical solutions be obtained with a digital computer. The numerical approximations of the partial differential equations are presented and the algorithm is discussed in detail. The analysis is applied to the detailed simulation of a forward-combustion laboratory tube experiment. The results of the simulation exhibit with reasonable accuracy all of the principal thermal and bydrodynamic characteristics observed in the laboratory (i.e., the propagation of a combustion zone, a steam plateau, and oil and water banks). Numerical variations in the parameters appearing in the external heat-loss term, the aqueous phase-change term, and the Arrhenius combustion term are examined, and their effects on the predicted temperature profiles, oil and water production histories, and the air-oil ratio are presented. In spite of an oversimplification in the chemical reaction mechanism and the considerable computer time required to obtain solutions, the model represents a major advance in the ability to simulate the phenomena observed in thermal recovery experiments. INTRODUCTION Thermal oil recovery refers to a class of recovery processes where heat is supplied to a reservoir to provide the necessary expulsive energy. This thermal energy can be supplied externally as steam or hot water, or it can be generated in situ by forward or reverse combustion. In either case, however, thermal recovery processes are charac- terized by the simultaneous flow of two or three fluid phases in a variable - temperature field, accompanied by possible chemical reaction or phase-change effects.2-5, 7- 10, 14,16-18,20-22 Although a physical understanding of the thermal recovery processes is far from complete, it is possible to construct mathematical models which describe approximately all of the principal physical and chemical phenomena. However, attempts to solve such models, even with high-speed computers, involve formidable mathematical difficulties. Consequently, theoretical solutions have been obtained only for idealized cases in which important physical phenomena are neglected. For example, consider the process of forward in situ combustion. All such theories which have been developed consider only certain aspects of the process, such as heat transfer, 2-4,8,9,l6,l8 heat transfer with phase change,10 heat transfer with chemical reaction,7 or the hydrodynamics of three-phase flow.21 A general theory including all of the above phenomena has not been developed to date. This paper presents a unified theory of thermal recovery processes in linear systems. A mathematical model is developed which explicitly includes conduction-convection heat transfer with convective external heat loss, chemical reaction between air and oil, aqueous phase change, and the hydrodynamics of three-phase flow. A system of equations is developed which can be solved numerically on a high-speed digital computer, resulting in predicted temperature, pressure, and saturation histories in space and time. The model allows a more detailed simulation of thermal recovery tube experiments than had previously been possible. THEORETICAL DEVELOPMENT Consider the linear flow of gas, water and oil in a homogeneous porous medium. Assume that the oil will react with gaseous oxygen, and that mass is transferred between the water and gas phase by evaporation or condensation. In the absence of hydrocarbon phase change, intraphase diffusion,

Jan 1, 1966

By George A. Roberts

The development of an alloy system, high-speed steel, is used as an example of the progress of physical metallurgy. Tracing the history of men and their thoughts as they studied and invented and modified these materials, the story of high-speed steel since the 1890's is seen to be a long, slow, but steady progression of achievements. Today's multiplicity of high-speed steels are the result. Data are presented on quantitative metallography of carbides in high-speed steel with high vanadium content using the QTM instrument. Grindability as well as mechanical properties are related to the content of excess MC and M6C carbides in a series of high-speed steels and the newer matrix steels. These emphasize the present state of knowledge and show the current stages of thought that may affect the development in succeeding years. It is a great thrill for me, an ex-research metallurgist and ex-practicing metallurgical engineer, to speak to an audience currently engaged in both pursuits on the occasion of the 43rd Howe Memorial Lecture before the Iron and Steel Division of the AIME. I shall not review Henry Marion Howe's distinguished career, so adequately reviewed in Maxwell Gensamer's contribution in the 1965 AIME History of Metallurgy, except to point out that, while leading the life of an intellectual, he worked as a practicing research metallurgist and a practicing metallurgical engineer for significant periods of time and contributed greatly in both areas. For those of you who believe, as I do, that in the intellectual activity of metallurgy we are blessed with an intimate mixture of science and engineering (see Mehl's 1960 Howe Lecture), we might recall that Howe, while pursuing a life of writing and teaching in later years, served as the first Chairman of the Division of Engineering of the National Academy of Sciences. That metallurgists were called upon then to lead an engineering recognition movement is perhaps related to the strong part played by the AIME and its members in the recent establishment of a National Academy of Engineering and to the fact that a metallurgist is its head, 47 years after Howe served. I stress these engineering aspects for I wish to talk about a metallurgical engineering subject today. Alloy systems, physical metallurgy, and steel blended with an historical perspective and a report on new techniques to improve the old will, I trust, be of sufficient interest to bring these lectures back to the physical-metallurgy banner from which they have departed for 4 years. Those process metallurgists, open-hearth fiends, and physical chemists among you will just have to be patient. The development of an alloy system is the engineering application of scientific thought and fact. There are many interesting alloy systems, developed to a high degree of technology and sophistication over the past 40 to 70 years. These systems are bound together and related by a similar set of characteristics. For example, stainless steels are a system in which the members are related by a high chromium content which gives a corrosion-resistant characteristic. A subfamily in this system would be austenitic steels

Jan 1, 1967

By Giovanni Barla, Stefan H. Boshkov

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The technique of calibrating gelatin mixtures proposed by Richards and Mark in 1966 is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example with the view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The prediction of the displacement, stress field and mode of fracture associated with a given rock structure, its initial stress field, and its physical properties is essential to rock mechanics and ground control. The basic approach is to assume the rock mass to behave as a continuous, homogeneous, and isotropic medium. The classical theory of elasticity is the simplest theory based on such a concept. Specification of the elastic constants, the initial state of stress in the ground, and the boundary conditions on stress and displacement allows one to predict stress and displacement within the body. Subsequently, provided that a criterion which governs rock fracture under various stress conditions has been established, a stability analysis of the rock structure can be performed. A natural extension of the present knowledge consists of removing some of the simplifying assumptions which characterize the analytical solutions based on the classical theory of elasticity. Complex geometry, the significance of tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space are some of the important factors which are neglected in the classical approach. A better insight into the real problem can be attained with either the finite element method of stress analysis or an experimental technique. The former has already been applied with success on several occasion 1-4 and is destined to render great service in the field of rock mechanics and ground control. The latter, which will be considered in this paper, has been used extensively in applications too numerous to be enumerated. Experimental technique involves either prototype testing, if the area to be studied is accessible, or model testing. Two- and three-dimensional photo-elastic analyses are very convenient means of obtaining the stress distribution in models of complex geometry. In general, such analyses are confined to studies of stress fields around openings which are sufficiently far removed from the surface boundary so that the stresses in their neighborhood are practically equal to those produced by an initial uniform stress field; i.e., so that gravitational effects are negligible. There are, however, many rock structures where these effects must be taken into account to attain a more realistic representation of the problem. Surface and near surface rock structures, systems of openings interacting with one another, and structural components loaded only by their own weight are some of the obvious examples. This paper was written to show how factors neglected in the usual analysis based on the classical theory of elasticity, can be taken into account when gelatin mixture models are used inconjunction with photoelastic methods. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with a view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The birefringence of gelatin mixtures has been known for some time. A series of experiments were carried out by Rossi in 1910,5 but after that very

Jan 1, 1970

As knowledgeable men in the industry know, a mineral occurrence is found through prospecting but an ore deposit is "made" -made through, first, imaginative and effective exploration; thence through efficient engineering, sales and management. There are two main phases of exploration-reconnaissance and target investigation-each of which can be further divided into two additional stages (see accompanying table). The search for a new ore deposit within a known and geologically mapped mining district involves only the last two stages, whereas the search for a new orebody in a virgin geologic environment involves at least three stages and often the full sequence. Of course, some of the exploration stages may be bypassed depending on available results of previous mineral surveys and/or exploration by individuals, business concerns, and governments.

Jan 10, 1967

By Morris Muskat

A theory is presented for calculating the performance history of complete water-drive systems producing from idealized stratified formations. The general equations are applied to systems where the permeability stratification is either of the exponential or linear type. Calculations were carried through for different degrees of permeability stratification, but with special emphasis on the effect of the mobility ratio between the produced oil and the invading water on the resultant performance. These results are also expressed graphically as curves for the initial water breakthrough recovery, for the different degrees of stratification, as a function of the mobility ratio, and of the composition of the produced fluid stream as a function of the cumulative oil recovery. For several typical cases the latter has also been plotted as a function of the cumulative oil and water throughflow. The general result is that when the mobility of the oil is lower than that of the invading water the channelling tendency resulting from the permeability stratification becomes aggravated as the higher permeability zones become flooded out. Situations of this type would obtain when producing low gravity or highly viscous oils. Conversely, if the mobility of the oil is high compared to that of the invading water, the flooding of the high permeability zones will lead to a retarding and choking effect, and the gross bypassing phenomena will be partially suppressed. These conditions would correspond to those of flooding high gravity or low viscosity oils. A discussion is given of the various basic assumptions made in the analysis, including that of ignoring the stripping phase of the production history as implied by relative permeability concepts. INTRODUCTION The physical ultimate recoveries from oil reservoirs are basically determined and limited by the physical oil displacement processes associated with the reservoir producing mechanism. In practice, however, the economic ultimate recoveries are further limited by the mobility of the reservoir fluids and the uniformity and continuity of the producing formation. In fact, it is the differential depletion between the component parts of the composite reservoir which ultimately determines the total recovery at the time of field abandonment. While this observation applies to both the solution gas drive and gravity drainage mechanisms, in which use is made only of the energy contained within the original oil-bearing reservoir, it is of even more paramount importance under operations wherein the energy associated with extraneous fluids provides the ultimate oil expulsion mechanism. Whether the invading fluid is the water from an edgewater drive, water injected for pressure maintenance, gas injected for pressure maintenance, or gas returned to the formation in a cycling program, it is often the continuity and uniformity of the producing section which will control the economic efficiency of the operations. The importance of the problem of reservoir non-uniformity does not, of course, lessen its complexity or the difficulties of its solution. In fact, these are inherently such that the concept of a "general" solution is virtually meaningless. About all that can be reasonably hoped for is the analysis of specific and well-defined types of non-uniformity which may give some degree of approximation to actual reservoir conditions. Since variations in the nature of the reservoir which depend only on the position along the streamlines will not lead directly to major differential depletion development within the reservoir, the types of non-uniformity considered thus far have involved stratification assumptions. That is, the producing section has been replaced by a multi-layer "sandwich," each uniform areally, and differing from the others only in its basic physical constants as to thickness, porosity and permeability. The fluid motion in the composite system is thus approximated by a parallel superposition of the independent fluid movements in the individual strata. For the specific application to cycling operations the theory of the effect of permeability stratification has been developed for both discontinuous' and continuous types of permeability stratification. Among the latter, treatments have been given of systems in which permeability distributions are governed by exponential, linear' or probability3 functions. In all these studies complete dynamical equivalence was assumed between the injected dry gas and the displaced wet gas. The overall effective permeability of each stratum was therefore considered as constant and independent of the degree of invasion of the injected fluid. In the case of the displacement of oil by water, the assumption of dynamical equivalence between the water and oil will be strictly valid only by accident. Even if the oil viscosity should be the same as that of the water, the effective permeability to the oil in the presence of the connate water will in general be quite different from that of the water behind the water-oil interface flowing past the trapped residual oil. As a result the effective permeability for the stratum as a whole and rate of water invasion will change with time as the intrusion continues. The differential fluid motion in the individual strata will thus also vary with time. Qualitatively, it is easy to predict the resultant effects. If the permeability to viscosity ratio of the invading fluid exceeds that of the fluid displaced, the stratification and bypassing effect of the perme-

Jan 1, 1950

By John D. Weibmer

A strong step towards acknowledgement of mining as a skilled trade has been taken by the Tintic Division of Kennecott Copper Corp. In May 2 ceremonies, a pilot program was signed into force which, possibly for the first time in US history, recognizes mining as an apprentice trade and grants journeyman status to those who complete the prescribed training sequence. The apprenticeship standards, hammered out after months of consultation between management, labor, and government, are presently limited only to underground hard-rock mining and only within Kennecott's Tintic Division, but the architects of the program are confident that the concept will spread-first to other underground operations where miners desire documented evidence of their special skills, then to open-pit and soft-rock operations.

Jan 6, 1977

By AIME AIME

T HE year 1920 will be a memorable one in the history of the world's coal supply. The prices reached were the highest of modern times, and as usually happens at such a time, the quality of the output deteriorated. In the last two years of the war, the world's output had risen close to the pre-war level. After the armistice, however, the cessation of munitions manufacture and the delay in resumption of normal business curtailed the demand for coal. Industrial disputes both in Europe and America closed many mines late in 1919 and further reduced the supply. Thus when in 1920 the world set its face to work again and industrial activity was resumed where resumption was possible, consumers' reserves of fuel proved insufficient and an almost universal feeling of apprehension over the coal supply swept around the world. The reasons for this alarm-lately a thing of the past-become clear when the world's production in 1920 is cast up.

Jan 1, 1921

By A. B. Young

T HE smelting industry in Utah is represented by four plants: The Midvale of the United States Smelting, Refining & Mini.ng Co., the Murray of the American Smelting and Refining Co., the Garfield of the same company and the Tooele of the Inter- na.tiona1 Smelting Co. The first two are lead smelters, the Garfield plant is a copper smelter while the last named embraces both a lead and copper smelter. A total daily smelting capacity of over 10,000 tons is represented, of which 4000 tons is lead smelting capacity. With the exception of Tooele, forty miles distant, all of these smelters are within twenty miles of Salt Lake City. Pyrometallurgical operations in this district are con- fined entirely to the production of unrefined bullion, which is shipped east to the various refineries of the respective companies. The smelting industry in this state had its beginning away back in the latter days of the Civil War, many years before the completion of the trans-continental railroad. Ox teams were still bringing their companies of better fixed Mormon emigrants across the plains to the valley of the Great Salt Lake and those in lesser circumstances were still pushing their hand- carts over the same roads to the temporary abode

Jan 1, 1925

By Freeman Bishop

Having obviously cleared the way for fast confirmation by the Senate Interior Committee, the Administration recently named Elburt F. Osborn, vice president of Penn State University, as director of the Bureau of Mines. Interior Committee Chairman Henry M. Jackson (D of Wash.) has moved hearings on the nomination right along, forecasting that they will end in a confirmation. Dr. Osborn not only made a good impression on the Committee, he also made it amply clear that he would be the boss of his job and have right-hand aides to help straighten out conflicts stemming from recently enacted health and safety regulations for miners. Mining engineers in the field hope this clarification can come soon. They are frankly fed up with local, state, regional and national overlapping of restrictions.

Jan 1, 1970

Geological and Natural History Survey of Wisconsin, The University of Wisconsin, Madison, Wis - E. F Bean, State Geologist. A complete list of publications of this Survey will be sent upon request Only a portion of the Bulletins and Maps fall within the scope of this directory, and most of them are available They are: Bulletin 4, Building and ornamental stones of Wisconsin (1898), $2 50, 6, Preliminary report on the copper-bearing rocks of Douglas County, and parts of Washburn and Bayfield counties (1901), 50 cents, 7, The clays and clay industries of Wisconsin (pt 1) (1901), 50 cents; 14, Report on lead and zinc deposits of Wisconsin (the report is out of print but the 18 maps which accompanied it can still be had) (1906), 20 cents (a series of six maps, supplementary to these (1909), may be had for 6 cents), 15, The clays of Wisconsin and their uses (1906), 50 cents; 16, The geology of north-central Wisconsin (1907), $2, 17, The abandoned shore lines of eastern Wisconsin (1907), 50 cents, 19, Zinc and lead deposits of the Upper Mississippi Valley (1907), 25 cents; 34, The limestone road materials of Wisconsin (1914), 50 cents, 35, Underground and surface water supplies of Wisconsin (1915), $150, 36, The physiography of Wisconsin (new edition now in press) (1916), $125, 41, A study of methods of mine assessments and valuation (1914), 50 cents; 44, Mineral land classification in parts of northwestern Wisconsin (1915), $5, 45, The peat resources of Wisconsin (1915), 50 cents, 46, Mineral

Jan 1, 1933

By Charles H. Fulton

ONE of the events of note in mineral industry education circles during the year was the summer school for engineering teachers, devoted to mining and metallurgical engineering, which was conducted by the Society for the Promotion of Engineering Education in co¬operation with the University of Wisconsin. It was in charge of Prof. Harry P. Hammond, director of the summer school, and Prof. Richard S. McCaffery of the University of Wisconsin. It was attended by 63 people, and practically every educational institution offering mineral industry courses had representatives present. The session was successful and those in attendance spoke highly of the pro¬gram and results obtained. The Mineral Industry Education Division cooperated with the S.P.E.E. in this project. Prof. Hammond will discuss the purpose and results of this session at the February meeting.

Jan 1, 1934

By Messrs. von Jonstorff

Continued Discussion of the Paper of Messrs. von Jonstorff, Blair, Dillner and Stead, presented at the New York Meeting of the Iron and Steel Institute, October, 1904.* (Bethlehem Meeting, February, 1906.) CLEMENS C. JONES, Richmond, Va. (communication to the Secretary+) :-In the chapter of this paper entitled "Method for the Determination of Phosphorus," by Andrew A. Blair, a form of the reductor used by Mr. Blair is illustrated. This form was employed by me in my earliest experiments, and abandoned after my adoption of the final apparatus described in my paper on the subject in 1889. The results reported by Mr. Blair are very closely accordant; but my experience was that, in the use of this form, a loss of the solution, amounting to almost a cubic centimeter, was occasioned by minute bubbles of hydrogen rising to the surface, and there exploding. My final reductor was designed to prevent this loss; and the most satisfactory results were obtained with a reductor having the open cup replaced by a bulb-shaped receptacle, provided with a glass stopper, similar to that of a separatory funnel of similar capacity, as suggested in a foot-note in my original paper. In my experience, the use of this later form of reductor repeatedly gave duplicate results which were, coincident to the fourth decimal place. R. W. RAYMOND, New York, N. Y.:-The. remarks of Mr. Jones recall to my mind an interesting part of the history of the Institute, and, of its relation to modern progress in the department covered by this interesting and valuable paper. In

Mar 1, 1906

By J. B. Wagner, p. Hembree

The iron tracer diffusion coefficient of umstite has been measured at 110(fC across the phase field and at a single composition at 800°C. Assuming a simple cation vacancy model the tracer diffusion coefficient was found to be a linear function of the cation vacancy concentration at 1100°C. The equation is D = 3 x 20 29 where denotes the concentration of vacancies in numbers per cc. The tracer work at 800°C was carried out to investigate the reported "pinning" of tracer to the wustite surface at low temperatures. No evidence for the "pinning" of the tracer was found at 800°C in COz-CO gas mixtures. HIMMEL, Mehl, and Birchenall,&apos; Carter and Richardson,2 and Desmarescaux and La combe3 have measured the diffusion of iron tracer in wustite at several temperatures and compositions. The present work was undertaken to extend the measurements over a large composition range at 1100°C and to resolve certain apparent discrepancies in the data, expecially at lower temperatures. EXPERIMENTAL Wustite was prepared by oxidizing rectangular iron plates* in C02-CO mixtures. The samples were •The iron was supplied by the Battelle Memorial Institute courtesy of the American Iron and Steel Institute. The analysis is presented in Table I. quenched. Due to the inward flow of cation vacancies during oxidation, the center of the sample contained a thin void. The edges of the wustite slab were sanded until the sample could be split into two parts. Each part was then sanded on the front and back flat area until a smooth surface was obtained. The specimens were then replaced in the furnace and equilibrated at llOO°C in a predetermined COa-CO mixture by methods described elsewhere.4"6 The specimens were again quenched and the surfaces were lightly sanded to remove any roughness following the first equilibration. The specimens were then reequi lib rated in the same C02-CO mixture for thirty minutes in order to relieve any mechanical damage on the surface due to the polishing. The specimens were then quenched and the tracer was applied by an electroplating technique. The work of Carter and ~ichardson&apos; demonstrated that there was no systematic difference in the iron tracer diffusion coefficient in wustite if the tracer was plated, dried, or evaporated on the specimen. In the present study a piece of filter paper was saturated with an iron chloride solution of pH <* 3 that contained the tracer FeS5. The wustite was placed on the filter paper and made the cathode. A current density of 0.4 to 0.6 ma per sq cm was passed for about five to ten minutes. The thickness of the tracer layer was estimated to be about 7 x lom6 cm. This estimate was made by considering the area plated, the current flow, and time for plating and the activity of the iron in the plating solution. Different areas of the specimen were counted using a collimator to determine the uniformity of the tracer. Any specimen which exhibited a variation from the initial count rate (about 1500 cpm) by more than 15 pct was rejected. An estimate of the time necessary to convert the thin layer of iron tracer to wustite was made using the data of Pettit and wagner." he estimated time was 1 sec at 1100°C assuming linear oxidation kinetics. The shortest diffusion anneals were 1800 sec. The samples were suspended in the hot zone of a furnace by two platinum wires. Two separate specimens were run at the same time. Only the edges of each sample were in contact with the wires. The C02-CO gas of the same composition as that used in the pre-diffusion anneals flowed freely around the samples at a linear velocity of 0.9 cm per sec. To initiate a run, the specimens were lowered from the cold zone of a furnace to the hot zone by a magnetic lowering device." bout 60 sec were required for lowering. To terminate a run, the sample was withdrawn from the hot zone to the cold zone. Time zero for the beginning of the experiment was taken when the sample blended into the red glow of the furnace and conversely for the end of the experiment. The surface decrease method of measuring the tracer diffusion coefficient was used to collect the data. This method requires that counting geometry be reproducible because the specimen is counted before the diffusion anneal and after the anneal. A special jig was constructed for each specimen so the specimen could be removed from the jig and returned to the jig such that the well geometry was reproducible.

Jan 1, 1970