Search Documents

By F. Petkovich, M. P. Sudbury

Development of a new method of treating flotation concentrates for the preparation of feed suitable for direct charging to blast furnaces or converters is described. The method takes advantage of the fact that pyrrhotite contained in the concentrates can be made to undergo exothermic reactions which, under properly controlled conditions, result information of oxidation products that serve to cement the concentrate particles together. Thus green concentrates either in the form of pellets or briquettes containing 5 to 8 pct moisture not only were hardened, but also completely dried autogenously by continuous countercu,vrent shaft treatment with air. The process was developed through pilot plant operations ranging from 35 1b per hr to 2.5 tph, culminating in products evaluation tests on a railway-car scale. Falconbridge Nickel Mines Ltd., Falconbridge, Ont., have practised sintering, on a travelling grate machine, for many years to prepare a pyr-rhotite-bearing Cu-Ni sulfide flotation concentrate for blast furnace smelting. In recent years the development of new mines, and the construction of concentration plants some 40 miles from the smelter has increased the quantity of concentrate shipped, and encouraged the search for a method of producing dry, hard pellets or briquettes suitable for direct charging to a blast furnace or converter, and capable of withstanding considerable handling. The cementing properties of pyrrhotite oxidation products were discovered during a search for a suitable agglomeration method for sulfide concentrates, and were exploited in a process subsequently developed for autogenously drying and hardening pellets and briquettes of pyrrhotite-bearing Cu-Ni sulfide flotation concentrate. EARLY TEST WORK The production of hard, dry pellets of concentrate filter cake was attempted in the drying plant of one of the new concentrators. While soft pellets were produced containing 5 pct moisture, attempts at further drying resulted in disintegration of the pellets and intolerable dusting. The plant therefore was controlled to produce a concentrate containing about 6 pct moisture. The partially dried concentrate, which was shipped to Falconbridge for sintering, tended to heat spontaneously in transit. An at- tempt to briquette the moist concentrate at Falconbridge, in a plant incorporating a muller, a 20-in. roll briquetting press, and a steam-heated travelling grate oven, was more successful, although the equipment corroded rapidly due to the acid nature of the concentrate after spontaneous heating had occurred. LABORATORY STUDIES OF SPONTANEOUS HEATING OF CONCENTRATE The spontaneous heating of partially dried concentrate was studied in the laboratory. Moist concen-

Jan 1, 1961

By David Cole

THE appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent m:-chine, or to (to more work except by the use of superimposed decks, the latter having obvious disadvantages. FIG. 1.-The- Butchart RIFFLE System. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2.

Jan 2, 1915

By Max Roesler

I. INTRODUCTION THE following article concerns the geological occurrence of the iron-ore deposits on the south coast of Cuba. The article is based on a detailed field study, made in the hope that some information would I gained which might be of value in the search for further orebodies, Or in the economic development of the ore already found. LOCATION The iron-ore deposits of the Firmeza district lie near the coast, in the southeastern part of Cuba, in the Province of Oriente. The orebodies of this district form part of a belt of deposits that extends from Sigua, 25 miles east of Santiago, to Sevilla, 5 miles east of Santiago, and lies on the seaward slope of the Sierra Maestra range of mountains.

Jan 10, 1916

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By H. H. Dreissen, F. J. Fontein

The operating principle of the classifying cyclone has been described often but some special aspects of the cyclone receive further clarification here. In addition, several uses of the classifiers are summarized and made clear by means of practical examples. In coal and ore washeries, the washing cyclone is widely used for the separation by specific gravity of sizes up to about 12 mm. This application has lately been extended to the separation by specific gravity of particles up to about 50 mm. This use makes special demands on the construction and wear resistance of the cyclone. The sieve bend, a development of the Dutch State Mines which is less well known than the hydrocy-clone, is dealt with at some length. The sieve bend is an apparatus designed for wet screening. Attention is given to the variables influencing the performance of the sieve bend. Hydrocyclones are now so widely applied that it would be difficult to find an industry not, directly or indirectly, using them or knowing how to use them since publications on this subject abound.1-3,5,9-11,13-15 However, because of the large number of variables influencing the operation of classifying cyclones, it is not entirely possible to calculate the results of this type of cyclone. Therefore, a number of lesser known variables will be discussed here along with some special applications of the classifying cyclone. FACTORS INFLUENCING CYCLONE CLASSIFICATION Shape of Particles: The shape of particles may cause a much coarser classification than the one expected, considering the sieve analysis and the cyclone dimensions chosen. This was clearly shown by feeding a mixture of spheres and disks in water into a cyclone. The spheres were 0.36 mm diam and the disks, 3 mm diam and 0.03 mm thick. These dimensions were chosen in order that the disks and spheres might have the same rates of fall under gravity. Both spheres and disks had a specific gravity of 1.05. The results obtained with these particles in a cyclone are summarized in Table I. Test No. 2 shows that the catch of spheres was

Jan 1, 1963

By Martin G. Castro, Renato G. Bautista, Morton Smutz

During the last 25 years, multistage mixer-settlers have been used extensively for liquid ion exchange work. The mixer-settler has the advantage of being a compact device in which a large number of stages can be assembled in a relatively small area. They are particularly advantageous for the separation of rare earths. Most of the adjacent rare earths have separation factors which are near one, which means that a large number of stages are needed to produce a good separation. When two elements (m, n) are extracted simultaneously, the separation factor (ßm, n) is defined as: [ ] where Ym, Yn are the molarities of the respective elements in the organic phase and Xm, Xn, are their molarities in the aqueous phase at equilibrium. The industrial consumption of rare earth oxides rose to over 6800 tons in 1968, an increase of 33% over 1967.1 The increased production and demand for rare earth and lanthanum chlorides for petroleum cracking catalysts was one of the principal factors in this increased consumption of rare earths. In 1968 approximately 59% of the rare earth oxides produced were used for gasoline cracking catalysts in the form of rare earth and lanthanum chlorides. There was also an increase in the sales of lanthanum oxides for use in optical lenses and in fiber optics. The future looks good for the rare earth industry. The rare earths can be expected to be used in many new products which are being developed. Until the late 1950's tributyl phosphate (TBP) was the principal solvent used in rare earth liquid ion exchange. In 1957 Peppard3 reported the use of di (2-ethyl-hexyl) phosphoric acid (D2EHPA) as a solvent for separating the rare earths. Rare earth separation factors of up to 2.5 were obtained in nitrate and chloride systems while the maximum separation factor using the

Jan 1, 1972

By Lawrence Addicks

T HIS has been a most momentous year in the annals of the Institute. We have been in the midst of a situation which, were it not for the convulsions of social unrest with which life is surrounded on every side, would have attracted the attention of the world at large. I do not refer to the desperate campaign for new members. That has gone on much as usual except that, this being leap year, the annual proposal to the M. & M. Society has been omitted. Nor do I refer to the desperate situation which we found in other directions, the spread of Bolshevism, the burning of the Engineers' Club, the fact that the selling of copper appears to have become one of the lost arts. No, I speak of the great question which has to be. settled once and for all, as to whether this great Institute should adopt simplified spelling. The whole trouble started in the ranks of the California Hysterical Society. It appears, while most of the San Francisco members can read and write, several of them cannot spell. It also appears that the Secretary, in editing the Transactions, has perhaps made just a little bit too much of a point of employing the correct Stoughton idiom. At any rate, the rebels filed an amendment to the constitution, and the stage was set for civil war, with perhaps more stress on war than on civil.

Jan 1, 1920

By R. Salter, C. K. Chase

Although Asarco's Silver Bell Unit, 40 miles west of Tucson, Ariz., is known primarily for copper production, molybdenite is also produced as a byproduct in the 8000 tpd flotation mill. The Silver Bell ore comes from two pits approximately two miles apart. Copper mineralization is essentially chalcocite resulting from two to three-fold secondary enrichment in a highly altered zone. A typical porphyry copper deposit, Silver Bell ore is of medium hardness. The ore consists of about one part molybdenum to 65 parts of copper. In the copper concentrate which is the starting point for separate molybdenum recovery, the ratio is also one part molybdenum to 65 of copper. Molybdenum mineralization is primary. Enrichment is not evident but it is notable that the molybdenite is more common in the more siliceous, harder rocks. The actual molybdenite occurs as diversely oriented flakes of fairly constant grain size, mostly in fractures associated with quartz veins. Most of the mineral appears unoxidized; secondary coatings on the molybdenite flakes are fortunately rare. In May 1962 a modified, improved version of the molybdenite circuit was put into operation.

Jan 7, 1964

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

By A. G. Rozner

TRANSVERSE rupture tests have been commonly used in mechanical investigations of brittle materials. The specimens are simple, easy to prepare, and loading presents no difficulty. Owing to the complexity of stress distribution in bending1 one can determine stresses rigorously only for the elastic range. The bend-test results, however, are at times converted into tensile-strength data, determined as maximum fiber stress. The assumption is made that for small plastic deformations the linear stress-strain relation applies. This problem was experimentally investigated by Bach3 who tested cast iron in bending and in tension and found that the maximum fiber strength obtained in bending exceeded the experimental tensile strength by a factor depending on the geometry of the tested piece. The factor varied from 1.57 for a rectangular cross section to 2.12 for a circular cross section of the tested beam. Since this work was carried out 60 years ago, the cast iron used could be expected to have been highly brittle, thus the extent of plastic deformation prior to fracture very small. We have therefore carried out a number of tests on magnesium-modified cast iron with an average elongation of -5 pct. It was hoped that the data obtained from the tests would serve as a guideline for comparing data obtained in tension and bending for brittle materials. Mechanical properties were measured at room temperature on an Instron tensile machine at a crosshead speed of 0.05 in. per min. The three-point bend test employed cylindrical bars 0.20 in. in diameter with a 1.0-in. span. For the tensile test, cylindrical tensile specimens with a gage length of 0.85 in. and a diameter of 0.160 in. were used. Results are summarized in Table I. From Table I one can see that fracture strength

Jan 1, 1965

Jan 1, 1967

By T. C. M. Pillay, John Chipman

The Si-0 equilibrium in liquid iron was investigated in some detail by Gokcen and Chipman1 who reported equilibrium constants of the following reactions: In each case the thermodynamic equilibrium constant K was obtained by extrapolating K' to infinite dilution. Their results on reaction [I] were consistent with those of earlier observers, and there seems to be little doubt as to the approximate validity of the equilibrium product determined. On the other hand, the results on reactions [2] and [3] indicated unusual curvilinear relationships between the activity coefficients of silicon and of oxygen and the silicon concentration. Since a linear relation is observed in all other similar instances, it was concluded that some source of error had affected the gas-metal equilibrium relationships. Recently the authors undertook a restudy of these equilibria with the view especially to establishing the equilibrium constant of reaction [2]. Their experiments, however, were discontinued before a tbroughly satisfactory answer had been obtained and consequently have remained unpublished until the present time. Quite recently Matoba, Gunji, and Kuwana2 published the results of a very thorough study of these equilibria. It is the purpose of the present note to Compare these three sets of experimental data, a comparison which leads to Confirmation of the results of Matoba and coworkers. The experimental arrangements described by Dutilloy and Chipman were employed. A controlled mixture of Hz, H,0, and argon was led into the induction furnace over the surface of the Fe-Si melt contained in a silica crucible. On account of the slow approach to equilibrium, runs were continued for at least 8 hr and, in some cases, as much as 12 hr. Samples were taken by means of silica tubes at the start and during the final 4-hr period of each run. Out of twelve runs only seven appeared to have approached equilibrium with sufficient certainty to be reported here. The results of these experiments, all at 1600°c, are shown by the triangles in Fig. 1. Equilibrium was approached from both oxidizing and reducing conditions and the direction of approach is indicated by the shape of the triangle. Attempts to extend the study to higher silicon concentrations were unsuccessful on account of the transfer of silica from the metal bath to the upper portions of the crucible by means of a silicon-monoxide mechanism. Matoba, Gunji, and Kuwana used similar methods and approached equilibrium from both sides. Their results at three temperatures are shown by the solid lines of Fig. 1. A line corresponding to 1600 deg is interpolated from their equations and is shown by the dotted line. The results of Gokcen and Chipman at 1600 deg in the range 0.02 to 2.0 pct Si are also shown. At concentrations up to about 0.6 pct Si, these investigators approached equilibrium from both directions, and their results in this range appear to be trustworthy. Above 1 pct Si, however, all of their experiments involved oxidation only, as shown by a decrease in the silicon content of the bath. It now seems certain that they failed to reach equilibrium at these higher silicon concentrations and that the curvilinear relation shown by their results is incorrect. It is evident that their results in the lower silicon range are in good agreement with those of Matoba and coworkers. In fact, a straight line drawn through their results would parallel the dotted line and would differ from it by only 0.05 in log K. The new data also lie close to that line. It may thus be concluded that the three sets of data are in good agreement and that the equations proposed by Matoba and coworkers for reaction [2] are satisfactory . They take the limiting value of log K', at 0 pct Si as log K ,. The slope of each line gives the value

Jan 1, 1962

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By Lewis M. Haupt

Discussion of the paper of Mr. Granger, presented at the New Haven meeting, February, 1909, and published in Bulletin No. 25, January, 1909, pp. 1 to 37. LEWIS M. HAUPT, Philadelphia, Pa. (communication to the 'Secretary*) :-This subject is of great interest to me, and I am noting progress and conditions as a test of my own judgment in advocating what I believed to be the nearer, cheaper and better route at Nicaraugua. I have as yet learned nothing to change my views, or modify the convictions which led me to retire from the Commission; but that is not the issue to-day. Our government is committed to the Panama route, and is bound to " make good." There are many points presented by Mr. Granger which seem to me worthy of very serious consideration. But when all is said there remains the risk of seismic convulsions, to which either form of canal is subject; and I fail to see that the risk would be reduced by making the cut deeper, with greater surcharge of lateral pressure upon the side walls. A severe earthquake in the rainy season would doubtless close either type of canal. One of the arguments in favor of the Panama route most insisted on, was that Nature had provided good natural harbors at its termini. Recalling this, it has interested me to note that the cost of creating the necessary harbors is estimated at $27,000,000. Mr. Granger refers to this, and quotes the Board's report to the effect that, on the Atlantic side, it will require 5 miles of jetties to " make an excellent harbor out of a wretched one." The vulnerable part of Mr. Granger's paper seems to me to lie in the admission that the plant required is still in the embryonic stage, and that at least one machine should be built and tested " to demonstrate that the theoretical strains and forces work out in practice exactly as expected." This, how-

Jul 1, 1909

By K. Leutwyler

The key to realistic casing stress analysis in thermal recovery installations is accurate knowledge of the temperatures involved. Much information leading to prediction of heat losses from tubing string to wellbore has been published. This .same information permits calculation of casing temperature under certain conditions. This paper reviews the basis for most of the published work, the line source solution to the diflusivity equation and examines some of its application criteria in the light of unsteady-state conditions. An alternate finite differences method is presented for correlation, and experimental data pertaining to the heat transfer mechanism in the annulus is reported. In the light of the information presented in the paper, it appears that the assumption of a line source for the tubing-wellbore system is valid even for reasonably short periods of heat flow, .such as "steam soak" operations. The empirically modified equation presented earlier matches computer derived results of the finite differences approach lor periods as short as 50 hours. Previously predicted cas ing temperatures and the associated stress levels are thus verified based on these correlative computations and the reported experimental information. Fall out from the computer output resulting in some studies of the influence of insulating cement properties on casing temperature, and experimentally studied effects of nitrogen placed in the annulus at various pressures., are described. INTRODUCTION Generally speaking, predictions of average casing temperatures have been based on an idealized model involving a centralized tubing string at uniform constant temperature radiating energy towards the casing under steady-state conditions.'. ' Heat is transferred away from the casing to the formation by unsteady-state conduction across thermal barriers consisting of cement and the mud sheath. Heat balances written on the casing permit prediction of instantaneous casing temperatures. During early periods of injection, casing temperature varies appreciably as a function of time; however, for long injection times this variation decays as heat flow from the wellbore to the formation stabilizes, and it becomes virtually negligible as conditions surrounding the wellbore become quasi-steady-state (Fig. 1). Carslaw and Jaeger -escribe a solution to the diffusivity equation for a line source (Fig. 2). A constant supply of heat is introduced into the medium from the line placed into the origin of the x-y coordinate system and parallel to the z-axis. Heat spreads outward in the infinite cylindrical solid and the temperature increase on a line going through point (x, y) parallel to the z-axis at a distance r can be predicted by: The following criterion must be considered: the Carslaw and Jaeger equation is obtained on the basis of a large

Jan 1, 1967

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By J. C. Martin

Stmplified equations are developed for the flow of fluids in gas drive reservoirs in which the effects of gravity can be neglected. The results show that the pressure distribution is governed by a nonlinear heat flow type of equation, and the saturation distributions are related to the pressure by the same equations QS those developed by Muskat for the average pressure and saturations in gas drive reservoirs. Unrler certain conditions the equation for the pressure can be approximated by the linear form of the heat flow equatlon. This equation tk analogous to the equation for the pressure in single-phase compressible flow The analysis reveals that the equation for the pressure in n~ultiphase flows can be obtained directly from the equation for the pressure in slngle-phase flows by simply replacing the single-phase compressibility by the total compressibility and the single-phase mobility by the sum of the mobilities of all the fluids present. Perrine's method of pressure buildup analysis for multiphme flows is based on these same substitutions. Thus, the development presented in this paper constitutes a theoretical justification for Perrine's method of pressure buildup analysis. One of the most difficult problems associated with the production of oil is the determination of the flow of the fluids within the reservoirs. One purpose of this paper is to present the development of simplified equations for the flow in gas drive reservoirs. The other purpose is to present some of the needed theoretical foundation for the methods currently being used in the analysis of multiphase pressure buildup data. The analysis presented in this paper makes use of a partial linearization of the equations governing multiphase flows. It is felt that the process of linearizing or partially linearizing the nonlinear equations of multiphase flows can lead to useful results since this process has proved extremely valuable in the study of other fields of science and engineering where nonlinear equations are encountered. Pressure buildup data of shut-in wells have been used for many years to estimate the static reservoir pressure. These data have also been used in studying the aver- age permeability both away from and close to the well-bores. The majority of the buildup data are obtained from wells producing two or three fluids. As yet the theoretical foundations for the methods of buildup analysis used in connection with rnultiphase buildup data have not been established. A number of methods of analysis of pressure buildup data have been developed." Most of these methods apply only to single-phase flows, and almost all of the theoretical analysis is confined to single-phase flows. Perrine' developed a method of analysis for rnultiphase flows from the method for single-phase flows of Miller, Dyes, and Hutchinson.' He did this by simply replacing the single-phase compressibility by the multiphase compressibility and replacing the single-phase mobility by the sum of the mobilities of the fluids in the rnultiphase flows. Obviously, such a procedure lacks a certain amount of theoretical justification, and such practices can lead to erroneous results. Fortunately, Perrine's results have a theoretical justification, and this justification is presented in the following discussion. It is assumed that gravitational effects and the cornpressibility of the rock can be neglected. Under these assumptions the equations governing the simultaneous flow of gas, oil and water in porous media areo* The preceding equations can be expanded into the following expressions.

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975