Search Documents

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By AIME AIME

THIS year the Chairman of the Institute's Iron and Steel Division is THIS William Anderson Haven, better known to the membership generally as Bill Haven. The Division Chairman is an individual endowed with a broad perspective of the ferrous metal industry he result of his earlier experiences as a successful operating man in the working and management of blast furnaces and his later experiences as an engineering-consulting executive concerned with the design and erection of and steel works throughout the world. William A. Haven was born to iron steel in the Pittsburgh district on ;. 1, 1888, and in due time--or in 1909 graduated from Penn State with a Bachelor degree in industrial chemistry.

Jan 1, 1944

By Thomas S. West

A gravel pack completion is described which, in addition to sand screening, permits the exclusion of water and gas from the oil production. A gravel pack composed of alternate layers of different particle sizes is employed which has horizontal but not overall vertical permeability to drilling mud. A packer is run on the tubing and set in the screen member, around which the gravel layers are placed. The hydrostatic pressure of a mud column prevents the entry of fluid above (or below) the level of the packer. The producing level may be changed by raising or lowering the tubing. Vertical coning is controlled by replacing the mud column with oil and continually injecting oil into the sand section above (or below) the packer. Three well histories with this completion are described in detail. Statistics on the first 100 completions of this general type are given. INTRODUCTION Gravel pack type completions have heretofore been almost exclusively for the purpose of preventing sand production. This paper describes and presents well data on a gravel pack procedure which is primarily a selective completion method. Although complete sand screening is achieved, the exclusion of gas and water is the primary objective. The application of this procedure is therefore not limited to unconsolidated sands. Application to hard sand or limestone reservoirs is equally feasible. GRAVEL PACK PROCEDURE Figs. 1 and 2 illustrate the gravel pack procedure employed. The gravel is placed by means of the frangible disc type dump bailer shown by Fig. 1.' This bailer has its lower end closed by a plate glass or steel rimmed cement disc. This disc breaks when the bailer passes over the liner allowing the gravel to be deposited around the liner. The liner employed is usually 2 3/8 in. to 2 7/8 in. OD and 1.995 in. or 2.07 in. ID (ID of 2-in. tubing or 2-in. line pipe). Two tvDes,. of slotted sections have been employed. One type employs horizontal hacksaw cut or milled slots of about 1/32 in. width opposite the producing section. The other type employs the same type,. of horizontal slot. but slots are placed in groups of six at intervals of about 8 in. A cage composed of half round vertical bars, spaced apart, is then welded to the pipe over the slotted sections. This liner has the bottom end closed, usually by bull plugging. The upper end is closed, while placing the gravel, by a cap which is held in place by means of a shear pin. This cap has a mandrel attached to it which extends downward inside of the liner to within a few inches of its lower end. The top of the liner cap is formed to fit a releasing type wire line core barrel overshot. The liner is lowered to bottom on the wire line by means of this overshot and released. The length of the liner is usually suffi- cient to extend to about 20 ft above the highest level to which gravel is to be placed, the upper end of the liner always being in the casing. The dimensions of the liner and bailer are such with respect to the casing size that the bailer will always pass over the liner. After releasing the liner the bailer is run to bottom. Passage of the empty

Jan 1, 1951

By Thomas S. West

A gravel pack completion is described which, in addition to sand screening, permits the exclusion of water and gas from the oil production. A gravel pack composed of alternate layers of different particle sizes is employed which has horizontal but not overall vertical permeability to drilling mud. A packer is run on the tubing and set in the screen member, around which the gravel layers are placed. The hydrostatic pressure of a mud column prevents the entry of fluid above (or below) the level of the packer. The producing level may be changed by raising or lowering the tubing. Vertical coning is controlled by replacing the mud column with oil and continually injecting oil into the sand section above (or below) the packer. Three well histories with this completion are described in detail. Statistics on the first 100 completions of this general type are given. INTRODUCTION Gravel pack type completions have heretofore been almost exclusively for the purpose of preventing sand production. This paper describes and presents well data on a gravel pack procedure which is primarily a selective completion method. Although complete sand screening is achieved, the exclusion of gas and water is the primary objective. The application of this procedure is therefore not limited to unconsolidated sands. Application to hard sand or limestone reservoirs is equally feasible. GRAVEL PACK PROCEDURE Figs. 1 and 2 illustrate the gravel pack procedure employed. The gravel is placed by means of the frangible disc type dump bailer shown by Fig. 1.' This bailer has its lower end closed by a plate glass or steel rimmed cement disc. This disc breaks when the bailer passes over the liner allowing the gravel to be deposited around the liner. The liner employed is usually 2 3/8 in. to 2 7/8 in. OD and 1.995 in. or 2.07 in. ID (ID of 2-in. tubing or 2-in. line pipe). Two tvDes,. of slotted sections have been employed. One type employs horizontal hacksaw cut or milled slots of about 1/32 in. width opposite the producing section. The other type employs the same type,. of horizontal slot. but slots are placed in groups of six at intervals of about 8 in. A cage composed of half round vertical bars, spaced apart, is then welded to the pipe over the slotted sections. This liner has the bottom end closed, usually by bull plugging. The upper end is closed, while placing the gravel, by a cap which is held in place by means of a shear pin. This cap has a mandrel attached to it which extends downward inside of the liner to within a few inches of its lower end. The top of the liner cap is formed to fit a releasing type wire line core barrel overshot. The liner is lowered to bottom on the wire line by means of this overshot and released. The length of the liner is usually suffi- cient to extend to about 20 ft above the highest level to which gravel is to be placed, the upper end of the liner always being in the casing. The dimensions of the liner and bailer are such with respect to the casing size that the bailer will always pass over the liner. After releasing the liner the bailer is run to bottom. Passage of the empty

Jan 1, 1951

Page Bronze Bearing Metals. By G. H. Clamer............... 162 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. Waring .. 166 The Tin-plate Industry. By D. M. BUck. Discussed by G. H. ClameR, J. W. RICHARDS............................ 168 The Aluminum Bronze Industry. By W. M. Corse............ 171 Bronzes, Bearing Metals, and Solders. By G. K. BURgess and R. W. Woodward. Discussed by G. H. Clamer, R. T. Roberts......... 175 Babbitts and Solder. By G. W. Thompson................ 184 The Cadmium Supply of the United States. By C. E. Siebenthal. Discussed by M. L. Lissberger, C. W. Hill, F. F. ColcoRd.......... 185 Solder, Its Use and Abuse. By M. L. LissbergeR............ 192 Bronze Bearing Metals G. H. ClameR,* Philadelphia, Pa.—Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early days, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 1, 1919

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By P. G. Nahin, A. Grenall, R. S. Crog, W. C. Merrill

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By W. C. Merrill, P. G. Nahin, A. Grenall, R. S. Crog

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By John V. Beall

Tsumeb has added a chapter to its absorbing history with the beginning of copper smelting operations this month. This development will be followed shortly by another one when lead smelting and refining plants go on the line next year. In our own milieu these events would be common- place enough (although a new lead smelter certainly would be cause for wonder), but in the sparsely settled remote regions of northern South West Africa they are a dramatic industrial expansion. They are also, however, a sound businesslike extension of policies which have marked the tenure of Tsumeb Corp. Ltd. The historical data given in Table I are a drab listing of factual bones without the corporeal splendor which should surround the denouement of the Tsumeb bonanza. When Sir Francis Galton traversed the country, his was an expedition which was in keeping with the then blooming era of heroic explorations. The Otavi highlands in the interior were unexplored and the reception of the natives uncertain. While the exploratory work was in progress during the turn of the century the Hottentots and Hereros were successively in open bloody rebellion. The suppression of these uprisings, particularly the Hereros, by German soldiers so decimated the tribes that a labor shortage ensued for many years, hampering the development of the colony. To these troubles may be added difficulties In obtaining mining supplies. However, there should have been no shortage of meat from wild game judging by conditions prevailing even today.

Jan 12, 1962

By Cornelius Kelley

THE American producers of silver are keenly alive to the importance of the silver problem and its vital effect on the mining industry in Montana and other States where precious-metal mining constitutes a basic industry. There are so many ramifications to the subject that one is tempted, no matter from what angle an approach is made, to digress along lines that inevitably lead into a maze of social, economic and financial problems, through which no clear pathway is marked, and regard¬ing which no definite opinion can be expressed, as the ultimate solution is dependent upon the policies adopted and carried out by the more important Governments with reference to their fiscal requirements and currency systems. The situation may be summarized in two questions First, what, if any, plan have the silver producers, as being the most directly interested, to offer in meeting the situation which will confront the industry upon the termination of purchases of domestic silver under the Pittman Act? Second, what, if any, assistance can be extended by the Government in connection with the problem? In answer to the first inquiry, while the matter has been the subject of discussion among the principal producers, they have been unable to formulate a defi-nite plan, principally because they have been and are dealing with a subject embracing many unknown fac-tors; and second, it has been felt that before any plan is adopted there should be indicated the extent to which cooperation on the part of the Government may be depended upon to enable a proper study of the situation to be made. In order to explain these rather cryptic statements, a general review of the situation may aid. Whatever differences of opinion there may have been in the past upon the subject of bi-metallism or the establishment of a fixed ratio between the coinage value of gold and silver, it will probably be conceded that it would be neither wise nor expedient to attempt a revival of this discussion, nor to undertake to solve the question by the adoption of such a remedy. Issues of contro-versial economics must be avoided, if possible-political economics will destroy rather than assist constructive effort.

Jan 2, 1923

By F. Twyman, D. M. Smith

Those chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates may be checked as often as desired. If, possessing these advantages, the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards 19cientific Paper No. 444. The Development of Analysis by Spectrogbaphy Fig. 1 shows, by means of photographs taken with a quartz spectro-graph, what a valuable region of the spectrum is excluded if one has a visual instrument only. Wave length 4023 is about the end of the visible spectrum, the region from 3800 to 1854 being invisible. It is easy to understand then how it is that the vigorous resuscitation of spectrum analysis which has commenced in the last few years has been associated with the use of the quartz spectrograph; notwithstanding that the most useful instrument for the general inorganic chemist to have at his elbow, after the balance, is a good visual spectrometer.(1) 1 The revival of spectrum analysis is to be attributed chiefly to the work of W. N. Hartley with his co-workers, and to A. de Gramont. Hartley,

By C. A. HEILANDG

THERE is a need for men well trained in geo- physical prospecting. Although the number of geophysicists required by the industry in the future cannot be expected to be very great, there will always be a demand for courses on the subject. A number of educational institutions are, therefore, interested in providing instruction in geophysical prospecting. Some institutions will be satisfied with courses in general geophysical prospecting designed to give the geologist fundamental concepts on the comparative merits of the methods and the interpretation of the results. Other institutions will want to give special instructions in theory, field procedure, and interpretation of any or all geophysical methods. In giving such special courses a number of problems will be faced, and it seems to me that such difficulties are easier to overcome in an engineering institution than in a university. A knowledge of basic engineering subjects, such as required of all students in an engineering school, seems to be the best foundation upon

Jan 1, 1930

As one surveys the extensive taconite operations on the Mesabi Range, he may find it difficult to believe that only 15 years ago, the iron ore mining industry here was staring at its own imminent demise. Due to the high demands for iron ore during World War II the postwar period of 1946-1950, and the subsequent "police action" in Korea, there was rapid consumption of the Mesabi's already depleted ores, and some economists were giving the Range only 20-25 years of life. In the 13-year period 1941-1953, more than 850 million tons of iron ore were shipped to steel mills, an amount almost equal to the total production during the preceding 30 years. Proven ore reserves dropped from 1.1 billion tons in 1940 to 8.3 million tons in 1954, the largest decrease being recorded in the famed direct shipping ores.

Jan 9, 1968

By David J. Selleck, Eugene P. Pfleider

9.61. Introduction. Open pit mining methods produce more than 80% of all raw materials today in the United States. Much of this comes either from properties that formerly employed underground methods and were converted to open pit or from mines that ultimately must go underground when the economic stripping limit is reached. Generally the ores are transported over large vertical distances and techniques have been developed to do this economically. One approach is to combine conventional surface trucking, over relatively level roads, with the use of gravity and underground facilities. There are various modifications, depending upon the character of the orebody and the topography. Several schemes, as used in Sweden, Canada, and the United States, merit describing. One of the critical problems involved in the transference of ores from surface to underground is that of flow of bulk solids. Must it be crushed? Will it hang up in the transfer? What size and inclination of ore pass are required. How is the ore best fed onto the transporting device underground? As an example, the planning engineers for the Carol Project of the Iron Ore Company of Canada faced these problems in making their designs for the production and transportation of some 55,000 tpd from their Smallwood Mine in Labrador. Other operations, facing somewhat similar conditions, used other approaches of interest. This chapter describes some of the factors involved in the design, construction, and operation of a combination surface underground transportation system as applied to open pit mining operations. 9.62. Tunnel-Ore Pass Systems. The type, shape, dip, and size of the orebody, as well as the surface topographic features, generally estab-

Jan 1, 1968

By Waldemar Lindgren

At the time of the discovery of America the old world had a scant supply of the precious metals. Both the northern and the southern part of the new continent proved wonderfully rich in gold and silver and its treasures were eagerly looted; though the looting has lasted four centuries, the mines of its mountain chains are far from being exhausted. Even the later discoveries in Australasia and eastern Siberia could not rob the Western Hemisphere of its position as the greatest gold and silver producing region of the world, though finally the developments in a narrow and circumscribed area in South Africa wrested from the Americas their supremacy in the production of gold. Nevertheless the history of the two parts of the great western continent has been strikingly different. At first the Spaniards extracted vast treasures of silver from Mexico, Peru, and Bolivia, while Colombia arid some placer deposits in Peru yielded a smaller quantity of gold. A couple of centuries later, a stream of gold began to flow from Brazil, the silver production from the countries mentioned above continuing strong in the meanwhile. Later on, the yield of South America diminished, but to offset this there began a wonderful series of discoveries in North America. The gold fields of California astonished the world; and when the cream of these had been skimmed off there began a no less amazing development of the Central Cordilleran gold and silver districts, which soon made the United States the greatest producer of the precious metals. Aided by ever improving technique, extensive exploration, and a system of railroads, the yield was maintained and increased. Still later followed the discoveries of the gold fields of the arctic region and silenced those who had maintained that the zenith in gold production had passed. Recently the province of Ontario in eastern Canada

Jan 1, 1917

By A. F. Taggart

THE following notes represent significant excerpts from a mass of records of experimental work done in the ore-dressing laboratory at the Columbia School of Mines during the years 1926 to 1928-inclusive. CLASSIFICATION OF EXPERIMENTAL WORK The experiments performed may be grouped for purposes of description under the following general -headings: I. Collecting agents. a. A method for quantifying collecting effect. b. Coating with undissolved collecting agents (oils) c. Action of dissolved collecting agents. II. Frothing agents. a. A method for quantifying frothing effect. b. Relation between frothing effect and chemical composition. III. Inorganic reagents. a. Methods of studying the effects of these reagents. b. Effect on slime dispersion. c. Effect on sulfides. SUMMARY OF THE ORIGINS OF PRESENT-DAY FLOTATION PRACTICE The first practicable, foolproof method of froth flotation was described in U. S. patent 835120, issued in 1906 to Sulman, Picard and Ballot, and in the equivalent patents in other countries. A number of less simple methods of producing the same result had been described previously in patent publications and otherwise.1 The reagents specified in all of these early patents were "oils" and, in addition, some inorganic substance, usually an acid. The quantities of reagents recommended and added were enormous when' compared with those used today.

Jan 1, 1929

WE must begin by defining what we mean by the Copperbelt. This term is generally used to denote that region of Northern Rhodesia in which the copper mines of that territory are situated. The first published use of the term Copperbelt we have been able to trace dates back to 1905. The African World of December of that year contained an article entitled "The Great Northern Copper Belts of Rhodesia." The next reference we have traced is in 1909 in an article in the Transactions of the Geo- logical Society of South Africa. It began to be used generally in the late twenties and by 1929 was in common use to denote the region which today contains the existing large copper mines of Northern Rhodesia. The first of three accompanying maps is a very simple outline map of Africa showing where Rhodesia is within Africa, and where the Copperbelt is within Rhodesia. The second is a larger scale map of the Copperbelt itself. It will be seen that within the present Copperbelt there are six producing mines. Two of these are new and four are relatively established, having started operations between the two world wars. The Copperbelt also includes a town- ship called Ndola, which is not a mining town, but a railhead on the main line. This town has developed primarily as a result of the mining industry in the neighborhood. It describes itself as the Gateway to the Copperbelt and is shortly to become a refining center.

Jan 5, 1957

By Richard Moldenke

One of the little-known characteristics of cast iron, which nevertheless has an important bearing on results where accuracy in machining is essential, is the ability of this material to ease up internal strains when allowed to remain quiescent for a more or less extended period of time. It seems as if the molecules in such a casting, by virtueof their "mobility," can adjust their relative positions to an extent sufficient to overcome some of the existing stresses. The following instance will perhaps give a fair idea of the condition a casting may be in when just shaken out of the sand. A very large sheave-wheel, after shaking out, was taken outdoors to be cleaned and made ready for turning up. It was leaned against the side of the building, but before much could be done an arm tore apart with a loud report. Investigation showed that the sun had been shining on the upper rim, thus adding a slight strain to those already existing within the arm and thus overbalancing the strength of the metal in tension. Had this sheave been kept under cover for a while, or at least until machined, the strains would have eased off sufficiently to allow the sun to look upon it without disaster. It will not be necessary to multiply examples. Every engineer knows the danger of water-hammer in pipe lines, particularly if the latter are of cast iron. Every mechanic knows, or should know, that it is not good to strike a fitting that is under steam pressure. It will be necessary to say a few words on the "internal strains" in castings—the so-called "casting strains" we hear so much about. We all know that to get a casting reasonably true to the dimensions wanted requires a slightly larger pattern. The usual allowance for gray iron is 1/8 in. to the foot (1 cm. per meter) and 1/4 in. to the foot (2 cm. per meter) for white iron (all dimensions). This reduction in length, breadth and thickness in a casting is erroneously called "shrinkage." It should be called "contraction," as for practical purposes it is simply the difference in dimensions of the casting red-hot and cold. The real "shrinkage" covers an entirely different situation. When a

Jan 1, 1917

By A. M. Adair

The effect of cathodically charging zone-refined iron with hydrogen and the resultant yield stress-grain size relationship has been investigated by tensile testing at -31°C. The resulting Petch plots (using a least-squares analysis) reveal a significant reduction in the slope and an increase in the intercept for specimens cathodically charged with hydrogen, regardless of whether the hydrogen is present during testing or is removed by evacuation. Other than surface blistering, the major effect of cathodically charging this material is to create occasional grain boundary cracks and thus presumably a large number of free dislocations at grain boundaries. These results are consistent with the hypothesis that the slope of the Petch plot is related to the stress required to activate dislocation sources at or near pain boundaries. While there is no significant effect of the presence of hydrogen on the lower yield stress of this material, the ductility is considerably reduced. After hydrogen removal by evacuation, the ductility recovers substantially and almost complete recovery of ductility is experienced by the smaller grain size specimens. THE influence of hydrogen on the mechanical properties of ferritic materials has received much attention throughout the history of the metallurgy profession. This interest has stemmed from the obvious importance of preventing the catastrophic failure of parts in service, and from the desire to determine what mechanism is responsible for the observed behavior. The various mechanisms proposed for hydrogen em-brittlement have been discussed in detail by Tetel-man,'who concludes that a combination of the applied stress and hydrogen pressure within voids best accounts for the many experimental observations reported. From a quite reasonable correlation of the strain aging and delayed-failure behavior of a variety of materials,2-7 Troiano and coworkers are of the opinion that the delayed-failure mechanism (slow strain rate embrittlement as well) is better explained as a lattice effect; solute elements diffuse to regions of high triaxial stress, form uncondensed atmospheres there, and effect a reduction in the cohesive strength of the lattice. Since hydrogen yield points8,9 have been observed in ferritic materials, and since the hydrogen embrittlement process may be related to strain aging, one further contribution to embrittlement could be hydrogen-dislocation interactions which make crack blunting by plastic deformation a more difficult process. The etch" relationship offers a means of comparing the relative ease of initiating and propagating plastic deformation in metals and alloys. In the present study, this relationship was used to compare the behavior of zone-refined iron in three conditions: uncharged, cathodically charged with hydrogen, and cathodically charged with hydrogen and evacuated. These Petch plots and the observed ductility parameters allowed a separation of the effects of the very presence of hydrogen and the act of cathodically charging hydrogen into this material. MATERIALS AND EXPERIMENTAL PROCEDURE An ingot of zone-refined iron was obtained from Battelle Memorial Institute which contained the following (typical) interstitial impurities in ppm: carbon, 10 * 5; nitrogen, 1; oxygen, 22; hydrogen, 0.9. The ingot was cold-reduced to a 1/2-in.-sq cross section, recrystallized 1 hr at 575°C, and then straight-rolled to a thickness of about 0.105 in. Tensile specimens were milled from the strip having a 1-in. gage length

Jan 1, 1967