Search Documents

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Dong Maolin

A great amount of high temperature off-gas, whose maximum temperature is up to 2100?, is generated during the smelting process of electric arc furnace (EAF). The dust content, which is mainly iron oxide, of the off-gas is high and worthy of industrial recovery. The heat carried by the high temperature off-gas with dust is about 11% of the total energy input of EAF, and some even is as high as 20%. The high-temperature off-gas not only takes away a lot of heat but also places a huge burden to de-dusting system of EAF. It not only reduces the iron oxide dust recovery ratio, but also causes serious pollution problems. With the development of the iron and steel industry, the proportion of molten iron for EAF gradually increases, and even more than 30% in some cases. The increase of molten iron causes increases in the amount of EAF off-gas and heat waste. As a result the problem of dust removal is worsening [1-2]. How to sufficiently recover the sensible heat of the high temperature off-gas, create conditions for efficient dust removal, thus reduce operating costs of dust removal system and the production costs is a problem which EAF steel making companies must pay attention to.

Oct 30, 2017

By Florian Markus Penz

The increase in Basic Oxygen Furnace (BOF) plants in steelmaking has given rise to renewed interest in a dynamic simulation of the BOF process. Material and process costs can be saved with optimized process times and targeted charging of scrap and slag formers. Beside hot metal, scrap is the main source of iron in the BOF process. Furthermore, scrap is used as a coolant during the process due to exothermal chemical reactions occurring in the BOF. In this paper, the melting and dissolution behaviour of scrap in the BOF process is discussed. A new dynamic thermodynamic and kinetic Matlab® model used to simulate scrap melting behaviour as a function of various scrap surface parameters and particle size is presented, as well as the influence of scrap properties on liquid bath temperature and final crude steel composition after a defined blowing period.

Oct 30, 2017

By Christoph Sedivy

Industrie 4.0 is slowly but surely arriving in the melt shops. Furnaces are being equipped with more and more sensors, digital models are increasing the degree of automation, and information is being shared between different aggregates within the plant. Because the electrode control system plays a key role in electric steelmaking, it naturally assumes an important position in the melt shop’s Industrie 4.0 strategy. In addition to reliable, state-of-the-art core regulation functionality, monitoring and reporting tools and the ability to communicate with other equipment are also required. Therefore, the latest generation of our electrode control system, the Melt Expert, was developed based on Industrie 4.0 design principles. Intelligent plant condition diagnostics, performance monitoring, and user-defined reporting are essential modules in this new system. With these functionalities, electrode control systems are developing into the information and control center of the furnace. A newly developed software app brings most relevant process information to mobile devices. This feature allows steelmakers to keep an eye on the performance of their equipment anytime and anywhere. This paper describes the new features of the electrode control system and shares our customers’ operational experience. Our focus is on the practical aspects of plant status monitoring, KPI reporting, and diagnostic functionality as well as the improvements achieved.

Oct 30, 2017

By Alessandro Molinari

In recent times, coke oven machines are acquiring a more prominent role in the coke making process. Apart from the traditional handling of the coal and coke flow, nowadays these machines are also deeply involved in all environmental and process control aspects. Paul Wurth coke oven machines have been developed by Schalke to meet the most recent requirements in terms of emissions control, automation, instrumentation, operability and maintainability. In CSP, Ceará, the new coke making plant represents the status of the art of the technologies applied to the whole coking process; starting from the Coke Oven Batteries and the Gas Treatment Plant developed by Paul Wurth up to the Coke Machines supplied by Schalker Eisenhütte, whose technology is now part of Paul Wurth coke making products portfolio. Present paper describes the plant configuration focusing on Coke Oven Machines and the key factors which are guarantying the success of the project.

Aug 16, 2017

By Rogério Felício dos Santos

Nitriding of metallic materials using electric discharges generated during electric discharge machining (EDM) is a recently developed technique. The aim of this paper was to correlate mechanical properties of a nitrided layer produced in AISI 4140 steel by EDM nitriding with the type and amount of nitrides. A conventional die-sinking EDM equipment and electrolytic copper electrodes were used to generate the electric discharges. The electrolyte was a solution of urea in deionized water. Knoop microhardness profiles assessed the variation of hardness along the nitrided layer, whereas the elastic modulus of this layer was measured using nanoindentation tests. Optical microscopy and X-ray diffraction (XRD) were used to characterize the nitrided surface. The results showed the formation of a nitrided layer containing iron nitrides with average thickness of around 25 µm. The amount of nitrides reduced from the surface towards the centre and these results correlated well with microhardness profiles obtained.

Jul 31, 2018

By Paul Riches

Today’s steel producers face the dual challenge of ensuring on-time delivery and ever demanding product requirements, while also running a lean operation. Every day the management of a long rolling plant requires continuous optimization of both operating and business practices. Imagine a long rolling facility, where individual pieces of equipment communicate with each other, where sensor information can be used not only for control purposes but to also monitor the condition of the equipment, where models are used to verify the process is within working limits and the equipment raises alerts to operators when it requires maintenance! Utilizing the ongoing evolution in technology though data collection, communication, internet of things, control techniques and smart sensors, there is now more information available than ever before. The collection and analysis of this information will both advance control and monitoring of plant performance; revolutionizing long rolling mill plants worldwide and optimizing the entire value chain, along with improved and more flexible production.

Oct 30, 2017

By Paulo Masiero

Sintered titanium carbide has been extensively used since the early 1980s for demanding wear-resistant applications and, in particular, in environments characterized by high temperature and oxidation. Thanks to its physical characteristics, especially its low density, titanium carbide (TiC) has been successfully applied in the manufacture of cassette guide rollers for hot steel rolling. However, the peculiar characteristics of the sintered Ti carbides make it difficult their redressing and hence this has always represented the limit for a more extensive application. Very often iron based alloys are preferred even if, in general, they are less cost effective just because they are easier to be redressed by turning. The availability of a simple, compact, fully automatic and reasonably priced CNC machine; specialized in the grinding of guide rollers and able to operate accurately and efficiently -both in contour and in plunge- can definitively solve TiC’s redressing problems and render its use even more widespread and attractive.

Oct 30, 2017

By Esteban Ruisanchez Rodriguez

In this paper we will discuss the process of the grain size customization of the EBT filler sand in relationship to the technical characteristics of the furnace and its tap hole. By customizing the grain size distribution, the glassy area formed on the top of the tap hole varies and supports differently the metallurgical pressure of the molten steel providing increased free opening speeds. Taylor made sand improves therefore the free opening rate, reduces the tap to tap time and increases the lifespan of the tap

Aug 16, 2017

By Thomas Höfler, Michael Auinger, Bernhard Linder

Gas-fired pusher furnaces are commonly used to heat steel slabs before hot rolling. Temperatures well above 1000 °C combined with an oxidizing atmosphere containing H2O, CO2 and O2 result in rapid oxidation of most steel grades. The resulting oxide scale and the chemistry of the metal-scale-interface are major determining factors for the occurrence of hot rolling defects. To better understand these phenomena, lab-scale trials were performed with two different steel grades in an electric tube furnace in the temperature range 1000-1250 °C, using an atmosphere of about 20 % H2O, 7 % CO2 and 3 % O2. Humidification of the gas was achieved by evaporation, using a custom thermostat with standard laboratory glassware. The resulting samples were prepared metallographically, using cold mounting under vacuum with taper section angles, and analyzed using light microscopy and SEM/EDS. The scale structure of the Si alloyed steel was highly dependent on the oxidation temperature due to the formation of eutectic liquid phases of FeO, Fe2SiO4 and FeAl2O4. Below the eutectic temperature, the scale of the Si steel appeared to be made up of three distinct areas: The external scale consisting solely of Fe oxides, the internal scale containing Fe2SiO4 and FeAl2O4, and an internal oxidation zone with SiO2 and Al2O3 in a mostly plain Fe matrix. Comparisons of the experimental results with simulations of the internal oxidation showed good qualitative agreement.

Oct 1, 2019

By Bruno Kneipel Neto, Mylena Inaiê Correia, Fabricio Cerqueira, José Francisco da Silva Filho

The automotive industry, when aiming to increase the resistance to corrosion, uses in the Body in White (BIW) concept the galvanized steels. The hot-dip galvanized steels that stand out most are known as GI steels. They are formed by the zinc element and by phases of intermetallic intermediate iron-aluminum-zinc compounds. The characteristic properties of the GI coating are directly related to the formation of the intermetallic layer, which is responsible for providing the connection between the metal substrate and the coating layer. In this context, two different types of steel (SAE1005 and TRIP780 steel) were used for laboratory characterization of their intermetallic layers through metallographic techniques. The results of the tests showed that the inclined section metallographic inlay technique allows obtaining a larger region of analysis of the intermetallic layer. For the surface analysis, it was observed that the chemical solution used in the preparation of the samples was effective, making possible an analysis more specific about the intermetallic layer formation, distribution and morphology.

Oct 12, 2019

By Roman Vaynshteyn

In places where Blast Furnaces are usually located, climatic factors may be unfavorable. Raw materials may be exposed to e.g. rain during transport/storage, bringing moisture into the process with consequences for stability and hot metal cost. This paper describes a technology for drying and pre-heating pellets and coke in the stockhouse. It does not require additional handling or logistical equipment and does not introduce extra transfer steps and degradation. Not only can moisture content be reduced, it can be controlled to a stable level by the operator.

Aug 16, 2017

By Jovanir Francisqueto, José Fagundes, Nayara Neves Coutinho, Marco Túlio Costa

The purpose of this project is to increase the visibility of which will be daily produced on the hot strip mill (HSM). The forecast was performed through the implementation of an automated tool for weekly HSM production planning. The project was started with the definition of the weekly planning process, through the determination of the main business objectives, like as: priorities of service (customers and delivery date), definition of HSM’s rules and restrictions of operating resources. Using a sophisticated mathematical model, through the computational simulation is possible the experimentation of various production scenarios, allowing the visualization of volumes by type of sequence, clients / priorities, mix to be produced, cylinder change quantity forecast, better forecasting of the productivity of the HSM, consumption of utilities, within others. Main benefits: sequencing which production orders should be produced, reducing unforeseen stops due lack of material, improving the quality of the stock which allows the reduction of the aging of slabs in the slabyard and the vision of customer services. Computational simulation as a weekly planning tool achieve, with other benefits, to present alternatives for better decision making.

Oct 6, 2019

By Nicola Santangelo

The current economic crisis and growing environmental issues have led the steel industry to face the simultaneous effects of low demand and production overcapacity in a globalized steel market, whilst confronting high energy prices and the need to comply with the green economy. Heat Recovery from waste gas of the Electric Arc Furnace (EAF) represents one of the greatest opportunities to reduce the consumption of primary energy and reduce the CO2 emissions in steel industry. The heat of the off-gas, if recovered and converted into electrical power, can make the whole Fumes Treatment Plant autonomous from the electric point of view, thus making it a “Zero-Energy FTP”. The concept is to substitute the Cooling Components (Water Cooled Panels and Air Cooler) are substituted with Heat Recovery Components (Hot Water Cooled Panels and Heat Exchanger). The recovered heat can be converted into power by using an Organic Rankine Cycle (ORC) turbine. The heat recovered by the HWCP and the Heat Exchanger is characterized by a variable thermal power, which affects the efficiency of the downstream ORC System. Danieli, in collaboration with the University of Udine, has developed the Thermal Stabilizer Unit (TSU). Danieli has realized the first step towards Zero Energy FTP at ABS steelmaking plant (Italy) by installing a CHR® - Clean Heat Recovery. This plant has been started up on 17th October 2014. The HMI of the CHR® is integrated in the HMI of the furnace, so all the process could be kept under control by the furnace operator. At ABS recovered thermal power reaches 5.5 MW. The max power production reached with CHR plant in ABS (over 1MW of electric power) consents an annual saving of approx. 500,000 EUR.

Aug 16, 2017

By Thomas Germershausen

Worldwide BOF-based steel plants are faced with demanding environmental requests and rising energy costs. For cleaning of primary gases from the BOF the scrubbing technology is worldwide adapted. For wet-scrubbers there is a direct relation between pressure loss and achievable clean gas dust content. Subsequently main energy consumers within Gas Cleaning Plants are the driving fans. To evaluate actual performance and to identify optimization measures extensive field measurements at existing Gas Cleaning Plants were performed. The operational results from various BOF plants worldwide will be presented and benchmarked. As a conclusion, advanced control strategies for reduced energy consumption and lower environmental impact were developed and implemented.

Jul 30, 2018

By Samuel F. Rodrigues, Clodualdo Aranas Jr., Fulvio Siciliano

The application of thermo-mechanical control processing (TMCP) in hot rolling of steels has become a common routine since the last 60 years. The understanding of the physical metallurgy behind TMCP played a major role in the early developments. Physical and numerical simulation works are performed firstly to derive the fundamental metallurgical knowledge and secondly to conceive existing TMCP practices. In this paper, a summary TMCP techniques is presented. The occurrence of dynamic transformation of ferrite in the austenite region is shown by means of synchrotron light diffraction methods. This phase transformation mechanism is taken into consideration and its effects on TMCP are proposed in an exploratory way.

Oct 1, 2019

By Giulio Rodrigues Altoé

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of epoxy matrix composites reinforced with continuous fique fiber, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Aug 16, 2017

By Yong Tian, Tian Zhang, Zhao-Dong Wang

To meet the requirements of high-performance steel plates, while reducing manufacturing costs and saving energy, the advanced cooling system for plate mill (ADCOS-PM) with functions of accelerated cooling (ACC), ultra-fast cooling (UFC), and direct quenching (DQ) was researched and developed by the State Key Laboratory of Rolling and Automation (RAL). Since 2003, several sets of ADCOS-PM device were developed and implemented in industrial practice. To fully utilize the ADCOS-PM technology, the combination of various strengthening mechanisms was promoted by NG-TMCP technology and low-cost, high performance plates were produced such as pipeline steels, and high-strength construction machinery steel.

Oct 1, 2019

By Francois Mignard

With a limited global steel production growth, automotive application market shows interesting volumes and trends especially in emerging countries. The recent period has again enabled Siemens VAI to confirm a position amongst leading suppliers of new plants serving high-end steel production in particular for unexposed and exposed automotive material. With a series of recent plant references in operation and under construction, relevant answers to such sustained level of performances are highlighted along the downstream processes. Designed for a wide range of applications, Siemens VAI processing lines includes advanced technological and state-of–the art equipment, among them, Solid state laser welder, Pickling Tunnel tanks, Skin pass mill and Tension leveller, Side trimmer with dynamic width adjustment, and new generation of Automatic surface inspection systems. With a continuous aim of driving improvements, Siemens VAI has also developed Global Quality Monitoring solutions notably through advanced software which provide just-in-time warnings and assist steel makers in the daily operation of their lines. As lifecycle partner, Siemens VAI offers solutions and services in metallurgical expertise from metallurgical modelling, through physical simulation on rolling, annealing and galvanizing processes, and enables Siemens to accompany our customers along with their project definition till fulfilment of highest market requirements.

Jul 30, 2018